User Manual - Warehouse Sound

System 10 and System 10 PRO Components
Digital Wireless
Installation and Operation
ATW-T1006
Boundary Microphone Transmitter
ATW-T1007
Microphone Desk Stand Transmitter
2
ATW-T1006 and ATW-T1007 Installation and Operation
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE
APPLIANCE TO RAIN OR MOISTURE.
CERTIFICATION: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. THIS DEVICE
COMPLIES WITH INDUSTRY CANADA LICENSE-EXEMPT RSS STANDARD(S). OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Cet appareil est conforme à la/aux norme(s) CNR exempte(s) de licence d’Industrie Canada.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas
causer d’interférence et (2) cet appareil doit accepter toutes les interférences, y compris celles
susceptibles de provoquer un fonctionnement non souhaité.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que
la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
WARNING: Changes or modifications not expressly approved in writing by Audio-Technica may
void the user’s authority to operate this equipment.
RF Exposure Statement: This transmitter must not be co-located or operated in conjunction
with any other antenna or transmitter used in other systems.
The ATW-T1006 and ATW-T1007 comply with FCC/IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and
RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF
energy that it deemed to comply without maximum permissive exposure evaluation. (MPE). But
it is desirable that it should be installed and operated keeping the radiator at least 20cm or more
away from person’s body.
Le ATW-T1006 et ATW-T1007 conformes aux limites d’exposition aux rayonnements énoncées
pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC. Cet équipement émet une énergie RF très faible qui est
considérée conforme sans évaluation de l ’exposition maximale autorisée. Cependant, il est
souhaitable qu'il devrait être installé et utilisé en gardant une distance de 20 cm ou plus entre le
dispositif rayonnant et le corps.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil umerique de la
classe B est conforme a la norme NMB-003 du Canada.
CAUTION! Electrical shock can result from removal of the transmitter chassis cover. Refer
servicing to qualified service personnel. No user-serviceable parts inside. Do not expose
to rain or moisture. The circuits inside the transmitter have been precisely adjusted for
optimum performance and compliance with federal regulations. Do not attempt to open the
transmitters. To do so will void the warranty, and may cause improper operation.
Danger of explosion if battery is replaced incorrectly. If battery dies, send transmitter to
Audio-Technica so battery can be replaced with same or equivalent type. Likewise, send
damaged, inoperable transmitters to Audio-Technica or other qualified service center for
recycling—do not throw away transmitter as its battery contains toxic materials.
Avoid leaving the transmitter in the open sun or in areas where temperatures exceed 110° F
(43° C) for extended periods. Extremely high humidity should also be avoided. Note: Placing
any object on a surface (such as a conference table) before its finish is fully cured may result in
damage to the finish.
Notice to individuals with implanted cardiac pacemakers or AICD devices: Any
source of RF (radio frequency) energy may interfere with normal functioning of the implanted
device. All wireless microphones have low-power transmitters (less than 0.05 watts output)
which are unlikely to cause difficulty, especially if they are at least a few inches away.
However, since a “body-pack” mic transmitter typically is placed against the body, we suggest
attaching it at the belt, rather than in a shirt pocket where it may be immediately adjacent
to the medical device. Note also that any medical-device disruption will cease when the RF
transmitting source is turned off. Please contact your physician or medical-device provider if
you have any questions, or experience any problems with the use of this or
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Unplug this apparatus during lightning storms or when unused for long periods of time.
10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
CAUTION on handling receiver battery
• Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open,
crush, modify, disassemble, heat above 140°F (60°C) or incinerate.
• Battery must be replaced and recycled by qualified service personnel.
• If the battery leaks and the liquid contacts your skin or clothing, immediately flush with
clean water.
• If the battery leaks and the liquid contacts your eyes, immediately wash thoroughly with
clean water and seek medical assistance.
• Do no short circuit; may cause burns or catch fire.
• Charge battery only with the supplied AC adapter and USB cable.
Thank you for choosing an Audio-Technica System 10 digital wireless
transmitter. You have joined thousands of other satisfied customers who
have chosen our products because of their quality, performance and
reliability. This wireless microphone system is the successful result of
years of design and manufacturing experience.
The ATW-T1006 System 10 Boundary Microphone Transmitter and
ATW-T1007 System 10 Microphone Desk Stand Transmitter are designed
to provide rock-solid performance along with easy setup and clear, natural
sound quality. Featuring two LED indicators, a user switch for talk/mute
toggling, gain control, low-cut filter and a rechargeable 3.7V lithium-ion
battery, the boundary and desk stand transmitters are both designed
to work with any System 10 receiver. Operating in the 2.4 GHz range,
far from TV and DTV interference, System 10 digital wireless systems
offer extremely easy operation and instantaneous channel selection.
Eight to ten transmitters may be used together without any frequency
coordination problems or group selection issues (consult the operator’s
manual for the System 10 receiver used to determine the maximum
number of transmitters that can be paired with a receiver and the
maximum number of channels that can be used simultaneously).
System 10 wireless ensures clear communications by providing three
levels of diversity assurance: frequency, time, and space. Frequency
Diversity sends the signal on two dynamically allocated frequencies
for interference-free communication. Time Diversity sends the signal
in multiple time slots to maximize immunity to multi-path interference.
Finally, Space Diversity uses two antennas on each transmitter and
receiver to maximize signal integrity.
The ATW-T1006 boundary microphone transmitter features a cardioid
condenser microphone element. The ATW-T1007 microphone desk
stand transmitter works with dynamic gooseneck or phantom-powered
condenser gooseneck microphones with an integral 3-pin XLRM-type
output connector.
3
ATW-T1006 and ATW-T1007 Installation and Operation
Installation
Transmitter Location
For best operation the ATW-T1006 boundary microphone transmitter
or ATW-T1007 microphone desk stand transmitter should be kept at
least 6' (2 m) from the System 10 receiver to help assure maximum RF
performance.
Power Connection
NOTE: Use only the supplied AC adapter and power cord to power or
charge the boundary and desk stand transmitters. To use AC power,
connect the power cord’s USB A-type male port to the AC adapter and
connect the Micro-USB B port to the USB Power Input on the rear of
the transmitter. Next, plug the adapter into a standard 120 V 60 Hz or
230 V 50 Hz (depending on global location) AC power outlet. The AC
adapter and USB cable also charges the transmitter’s internal battery.
Charge battery in an environment with moderate temperature (41°F –
95°F). The system will not charge in temperatures below 32°F or above
104°F in order to prevent potential damage to battery. For safety and to
conserve energy, unplug the AC adapter from the AC outlet when the
system is not in use. Store transmitter in a cool place.
ATW-T1006 Boundary Microphone Transmitter and
ATW-T1007 Microphone Desk Stand Transmitter
Controls and Functions
Figure A—ATW-T1006 and ATW-T1007 (Top)
1. User Switch: Depending on switch function setting, press to toggle
talk/mute, press to talk or press to mute.
2. LED 1: Indicates transmitter status: power on/off, mute/talk, battery
low/charging. See LED chart on page 4.
3. LED 2: Indicates transmitter status: power on/off, mute/talk, battery
low/charging. See LED chart on page 4.
4. 3-Pin XLRF-type Input (ATW-T1007 only): Use to mount any
gooseneck microphone with an XLRM-type output
Figure A
ATW-T1006
3
4
1
Figure B—ATW-T1006 and ATW-T1007 (Bottom)
1. Battery Compartment
2. Pairing Switch: Press to complete pairing sequence. See page 5.
3. System ID Display: Shows System ID. See page 5.
4. Power Switch: Press and hold to turn receiver on or off.
5. Switch Function: Press to change functioning of User Switch
6. Gain Control: Press to change input gain level.
7. Low-Cut Switch: Press to turn low-cut filter on or off.
8. Power Input: Connect the AC Power Supply adapter included in
the system to charge/operate the transmitter.
ATW-T1007
3
2
1
Figure B
8
1
3
2
4
5
6
7
2
4
ATW-T1006 and ATW-T1007 Installation and Operation
Transmitter Operation
Press and hold the Power switch on the bottom of the transmitter. (The
electronics in the transmitter take up to 30 seconds to stabilize after
power is applied.)
Both the ATW-T1006 boundary microphone transmitter and the
ATW-T1007 microphone desk stand transmitter should be placed
on a flat, unobstructed mounting surface. The ATW-T1006 should be
positioned so the front of the microphone faces the sound source. The
sound source should not be below, or higher than 60° above, the plane
of the mounting surface.
Figure C—LED Function
The boundary and desk stand transmitters both feature a touchsensitive user switch and two red/green LED status indicators – one
integrated into the user switch on the front on the unit, the other bent
in an L-shape to display on both the top and rear of the unit. This dual
LED configuration allows the transmitter status to be viewed by the
user and by those seated opposite the user.
The boundary and desk stand transmitters operate in two different
modes: Standard and Conference. In Standard mode, which is
the default, both LEDs will illuminate green when the transmitter
microphone is on and will illuminate red when the microphone is
muted. In Conference mode, both LEDs will illuminate red when
the transmitter microphone is on and will not illuminate at all when
the microphone is muted. (An exception for both modes is when
the transmitter power is off and charging cable is plugged into the
transmitter. In this case LED 1 will not illuminate, while LED 2 will
illuminate red while the battery is charging and illuminate green once
the battery is fully charged.)
To switch between Standard and Conference modes, press and hold
the recessed Switch Function button and, while continuing to hold it,
press and hold the Power button. After a few seconds, the mode will
change and the system ID will briefly display A for Standard mode and
C for Conference mode.
Locking the Mute Function
1. Turn the transmitter off.
2. Press and hold the recessed Pair button and, while continuing to
hold it, press and hold the Power button until the transmitter powers
on. The dot that usually appears next to the System ID will not be lit,
indicating that the mute lock has been activated. The LED below the
Switch Function button will also not light when the mute lock is on.
3. To deactivate the mute lock, turn the transmitter off again, then
press and hold the Pair and Power buttons as before until the
transmitter powers on. The dot will once again display next to the
System ID and the Switch Function LED will light, indicating that the
mute lock has been deactivated.
Adjusting Settings
The settings for the user switch, input gain level and low-cut filter can
all be adjusted by pressing the appropriate recessed button on the
bottom of the transmitter.
Standard Mode
Figure C
Condition
Transmitter Power
LED 1
LED 2
LED 1
LED 2
Not linked with Receiver
On
Red/Green
Alternate
Green/Red
Alternate
Red/Green
Alternate
Green/Red
Alternate
Initialize/Toggle Mode
On
Green
Green
Red
Red
Initialize/Press to Talk
On
Red
Red
Off
Off
Initialize/Press to Mute
On
Green
Green
Red
Red
Mic Mute
On
Red
Red
Off
Off
Mic Talk
On
Green
Green
Red
Red
Charging/Mic Mute
On
Red
Red
Off
Off
Charging/Mic Talk
On
Green
Green
Red
Red
Fully Charged/Mic Mute
On
Red
Red
Off
Off
Fully Charged/Mic Talk
On
Green
Green
Red
Red
LED 2
LED 1
Conference Mode
Low Battery/Mic Mute
On
Red Blink
Red Blink
Off
Red Blink
Low Battery/Mic Talk
On
Green Blink
Green Blink
Red Blink
Red Blink
Charging
Off
Off
Red
Off
Red
Fully Charged
Off
Off
Green
Off
Green
5
ATW-T1006 and ATW-T1007 Installation and Operation
Setting the Switch Function
1. The default Switch Function setting is TOGGLE ON/OFF (with
audio on at power up). The LED below the Switch Function button
illuminates green for this setting.
2. Press the Switch Function button once to select MOM. ON
(momentary on), wherein the audio will be on only while the user
switch is being pressed (press to talk). The LED below the Switch
Function button illuminates orange for this setting.
3. Press the button a second time to select MOM. OFF (momentary
off), wherein the audio will be muted while the user switch is being
pressed (press to mute). The LED below the Switch Function button
illuminates red for this setting.
4. Press the button a third time to cycle the setting back to the default.
NOTE: With all transmitters turned off, the receiver’s System ID Display
will cycle through all currently paired ID numbers. Turn on a transmitter
to activate its pairing with the receiver. The receiver recognizes only one
transmitter at a time. That transmitter must be turned off before the
receiver will recognize another paired transmitter. If that transmitter is
turned off out of range, the receiver will not recognize another paired
transmitter until the receiver is powered off and turned on again.
Selecting the Input Gain Level
1. There are three input gain levels that can be selected: -6 dB (for
loudest voices), 0 dB and +6 dB (for softest voices). The default
setting is 0 dB, which the Gain LED indicates by illuminating orange.
2. Press the recessed Gain button once to change the level from 0 dB
to +6 dB. The LED will illuminate red.
3. Press the Gain button again to change the level to -6 dB. The LED
will illuminate green.
4. Press the button a third time to return the level to 0 dB. The LED will
illuminate orange.
3. Release the Pair and ID buttons and, after a few seconds, the display
will stop blinking and return to normal operation.
Engaging the Low-Cut Filter
1. The low-cut filter is off by default. The corresponding LED indicates
this by illuminating red.
2. Press the recessed Low Cut button to turn the low-cut filter on. The
LED will illuminate green.
3. Press the button again to turn the filter off. The LED will illuminate red.
Setting System ID Number and Pairing Transmitter with a Receiver
NOTE: System ID is an identical number assigned to a paired receiver
and transmitter for identification purposes. The System ID number is not
related to transmitting frequency. Due to the dynamic nature of System
10's automatic frequency selection, the actual transmitting frequencies
may change during power-up or performance. These frequency changes
are seamless and imperceptible to the ear.
NOTE: Up to ten transmitters may be paired with a System 10 PRO
receiver. Up to eight transmitters may be paired with other System 10
receiver models.
1. Turn on the receiver and transmitter.
2. Press the System ID button on the receiver to select a System ID
number from 0 to 9 (1 to 8 if not using System 10 PRO receiver).
3. Within 15 seconds, press and hold the Pair button on the receiver for
about one second. The receiver’s Pairing Indicator will begin to blink
green. Your receiver is now in Pair Mode.
NOTE: If the receiver’s Pair button is not pressed within 15 seconds, the
System ID number will revert to its previous setting.
4. Within 30 seconds of entering Pair Mode, press and hold the
recessed Pair button on the bottom of the transmitter. The transmitter display will show the System ID number you have chosen on the
receiver. The receiver’s Pairing Indicator will glow steady, indicating
you have successfully paired your system.
5. To pair an additional transmitter, you must switch off the first transmitter by pressing and holding its Power button. Turn the second transmitter on and follow instructions 2-4 above, making sure to assign a
different System ID number to the new transmitter.
6. Repeat for each additional transmitter you wish to pair with this
receiver. Remember to switch off all transmitters already paired
before adding a new one and to use a unique ID number for each
transmitter.
Clearing Individual ID Pairings
1. Press the receiver’s System ID button to select the ID number you
wish to clear. The number will begin to blink.
2. Press and hold the Pair button and, while continuing to hold it, press
and hold the ID button until the display shows a blinking “o.” This indicates that your selected ID number has been cleared.
4. Repeat to clear additional ID pairings.
Clearing All ID Pairings
1. Press and hold the receiver’s Pair button and, while continuing to hold
it, press and hold the ID button until the display shows a blinking “o.”
2. Release the Pair and ID buttons. Then, within three seconds, press
and hold the Pair and ID buttons again, until the display shows a
blinking “A.” This indicates that all your paired ID numbers have been
cleared.
3. After blinking for three seconds, the “A” will change to “-” to indicate
that there are no paired transmitters.
Restoring Factory Default Settings
The factory default settings for the boundary and desk stand
transmitters are as follows:
• System ID Number: 1
• Switch Function: Toggle mode (LED: Green)
• Gain: 0 dB (LED: Orange)
• Low-cut: Off (LED: Red)
• Mode: Standard mode
• Mute lock: Off
To restore the settings to the factory default, push and hold the Low
Cut button and, while holding it, push and hold the Power button. The
three LEDs on the bottom of the transmitter will rapidly blink green for
two seconds and then illuminate according to default settings once the
defaults have been restored.
NOTE: All settings will be restored except for the System ID number.
This number and pairing with the receiver will be retained. See above for
instructions on setting and clearing System ID numbers and pairings.
System Operating Frequencies
Automatic Frequency Selection
System 10 wireless systems operate in automatically selected frequencies in the 2.4 GHz range, far from TV and DTV interference. Up to ten
channels (eight channels if not using System 10 PRO receiver) may be
used together without any frequency coordination problems or group
selection issues. Every time a receiver/transmitter pair is powered on,
it automatically selects clear frequencies. Due to the dynamic nature of
System 10 automatic frequency selection, these transmitting frequencies may change during power-up or performance if interference is
encountered. These frequency changes occur at both the receiver and
transmitter; they are seamless and imperceptible to the ear.
6
ATW-T1006 and ATW-T1007 Installation and Operation
System Frequencies
For future reference, please record your system information here (the serial number
appears on each transmitter).
Transmitter
ModelATW-T100
Serial Number
6 or 7
Specifications
Overall System
Operating Frequencies
Total Harmonic Distortion
Operating Temperature Range
Charging Temperature Range
Frequency Response
Audio Sampling
2.4 GHz ISM band
<0.1% typical
0° C to +40° C (32° F to 104° F)
Battery performance may be reduced at
very low temperatures
5˚C to + 35˚C
20 Hz to 20 kHz
Depending on microphone type
24 bit / 48 kHz
To reduce the environmental impact of a multi-language printed document, product information
is available online at www.audio-technica.com in a selection of languages.
Afin de réduire l’impact sur l’environnement de l’impression de plusieurs langues, les
informations concernant les produits sont disponibles sur le site www.audio-technica.com dans
une large sélection de langue.
Para reducir el impacto al medioambiente, y reducir la producción de documentos en varios
leguajes, información de nuestros productos están disponibles en nuestra página del Internet:
www.audio-technica.com.
Para reduzir o impacto ecológico de um documento impresso de várias linguas, a Audio-Technica
providência as informações dos seus produtos em diversas linguas na www.audio-technica.com.
Per evitare l’impatto ambientale che la stampa di questo documento determinerebbe, le
informazioni sui prodotti sono disponibili online in diverse lingue sul sito www.audio-technica.com.
ATW-T1006
Maximum Input Sound Level
RF Power Output
Spurious Emissions
Power Supply
Internal Battery
Battery Life
139 dB SPL
10 mW
Following federal and national regulations
100-240V AC (50/60 Hz) to 5V DC 0.5A
switched mode external USB-type
power supply
3.7 V Rechargeable Li-ion Battery
9 hours
Der Umwelt zuliebe finden Sie die Produktinformationen in deutscher Sprache und weiteren
Sprachen auf unserer Homepage: www.audio-technica.com.
Depending on environmental conditions
Battery Charging Time
4 hours 30 minutes
本公司基于减少对环境的影响,将不作多语言文檔的印刷,有关产品信息可在
www.audio-technica.com的官方网页上选择所属语言和浏览。
Depending on environmental conditions
An empty battery will recharge 90% in 2 hours.
Dimensions
Net Weight
Accessory Included
96.1mm (3.78'') W × 38.0mm (1.50'') H
× 122.8mm (4.83'') D
408 grams (14.4 oz)
AC adapter (USB-type), USB cable
ATW-T1007
RF Power Output
Spurious Emissions
Power Supply
Phantom Power
Internal Battery
Battery Life
10 mW
Following federal and national regulations
100-240V AC (50/60 Hz) to 5V DC 0.5A
switched mode external USB-type
power supply
12V DC
3.7 V Rechargeable Li-ion Battery
9 hours
Depending on environmental conditions
Battery Charging Time
4 hours 30 minutes
Depending on environmental conditions
An empty battery will recharge 90% in 2 hours.
Dimensions
Net Weight
Accessory Included
96.1mm (3.78'') W × 44.2mm (1.74'') H
× 122.8mm (4.83'') D
392 grams (13.8 oz)
AC adapter (USB-type), USB cable
In the interest of standards development, A.T.U.S. offers full details on its test methods to
other industry professionals on request.
†
For product improvement, the product is subject to modification without notice.
Om de gevolgen van een gedrukte meertalige handleiding op het milieu te verkleinen, is
productinformatie in verschillende talen “on-line” beschikbaar op: www.audio-technica.com.
Для снижения вредного воздействия на окружающую среду от печати многоязычного документа,
информация о продукте доступна онлайн на www.audio-technica.com на нескольких языках.
www.audio-technica.com
7
ATW-T1006 and ATW-T1007 Installation and Operation
This page intentionally left blank.
ATW-T1006 and ATW-T1007 Installation and Operation
Audio-Technica Corporation
audio-technica.com ©2016 Audio-Technica P52585
Download PDF