IP CAMERA SERIES
OPERATION GUIDE
Please read instructions thoroughly before operation and retain it for future reference.
459a_359a_459ah_359ah_552a_552ah_565a_561_561h_552b_552bh_459b_459bh_552C_358_358H_458_458H V1.6
IMPORTANT SAFEGUARD
All lead-free products offered by the company comply with the requirements of the
European law on the Restriction of Hazardous Substances (RoHS) directive, which means
our manufacture processes and products are strictly “lead-free” and without the hazardous
substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product
must be collected separately at the product end-of-life. This applies to your product and
any peripherals marked with this symbol. Do not dispose of these products as unsorted
municipal waste. Contact your local dealer for procedures for recycling this equipment.
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device mat not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Trademark Acknowledgements
iPad® & iPhone® are the registered trademarks of Apple Inc.
Android™ is a trademark of Google Inc. Use of this trademark is subject to Google Permissions.
Microsoft®, Windows® & Internet Explorer® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
Disclaimer
We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume
any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. The content of
this manual is subject to change without notice.
This product doesn’t have a standby / off mode.
MPEG4 Licensing
THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN
COMPLIANCE WITH THE MPEG4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING
MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND
NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY
MPEG LA TO PROVIDE MPEG4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY
OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL
AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE
HTTP://WWW.MPEGLA.COM.
GPL Licensing
This product contains codes which are developed by Third-Party-Companies and which
are subject to the GNU General Public License (“GPL”) or the GNU Lesser Public License
(“LGPL”).
The GPL Code used in this product is released without warranty and is subject to the
copyright of the corresponding author.
Further source codes which are subject to the GPL-licenses are available upon request.
We are pleased to provide our modifications to the Linux Kernel, as well as a few new
commands, and some tools to get you into the code. The codes are provided on the FTP
site, and please download them from the following site or you can refer to your distributor:
Model 1, 2, 3 & 4: http://download.dvrtw.com.tw/GPL/IPCAM/F-Seriers/linux.tar.gz
Model 5: http://download.dvrtw.com.tw/GPL/IPCAM/A-Seriers/linux.tar.gz
Model 6 & 7: http://download.dvrtw.com.tw/GPL/IPCAM/S-Seriers/linux.tar.gz
TABLE OF CONTENTS
1. OVERVIEW......................................................................................................................................... 1
1.1 Product Features....................................................................................................................................... 1
1.2 Package Content....................................................................................................................................... 1
1.3 Cable Overview ......................................................................................................................................... 2
1.5 External Alarm Connection........................................................................................................................ 2
2. CAMERA ACCESS WITH INTERNET EXPLORER............................................................................ 4
2.1 Camera Login............................................................................................................................................ 4
2.2 Control Panel Overview ............................................................................................................................ 4
2.3 Digital PTZ (DPTZ) Operations ................................................................................................................. 6
2.4 Event Record Search & Playback ............................................................................................................. 8
3. CAMERA CONFIGURATIONS............................................................................................................ 9
3.1 System configuration menu....................................................................................................................... 9
3.2 Network ................................................................................................................................................... 11
3.2.1 Network .......................................................................................................................................................... 11
3.2.2 QoS ................................................................................................................................................................ 11
3.2.3 DDNS ............................................................................................................................................................. 11
3.2.4 SNTP.............................................................................................................................................................. 11
3.2.5 FTP.................................................................................................................................................................12
3.2.6 MAIL ...............................................................................................................................................................12
3.2.7 SMS................................................................................................................................................................13
3.2.8 Filter ...............................................................................................................................................................14
3.2.9 UPnP / Bonjour...............................................................................................................................................14
3.2.10 RTP ..............................................................................................................................................................15
3.3 Camera ................................................................................................................................................... 17
3.3.1 Camera...........................................................................................................................................................17
3.3.2 Video ..............................................................................................................................................................17
3.3.3 Color...............................................................................................................................................................18
3.3.4 Advanced........................................................................................................................................................18
3.3.5 Privacy Mask (For selected models only) ......................................................................................................19
3.4 Record..................................................................................................................................................... 20
3.4.1 Record............................................................................................................................................................20
3.4.2 Record Timer..................................................................................................................................................20
3.5 Storage.................................................................................................................................................... 20
3.5.1 Memory ..........................................................................................................................................................20
3.6 Trigger ..................................................................................................................................................... 21
3.6.1 Trigger ............................................................................................................................................................21
3.7 General ................................................................................................................................................... 22
3.7.1 General...........................................................................................................................................................22
3.7.2 Time................................................................................................................................................................22
3.7.3 Server Log......................................................................................................................................................23
3.7.4 Online .............................................................................................................................................................23
3.7.5 Account...........................................................................................................................................................24
3.7.6 Google Maps ..................................................................................................................................................24
3.7.7 Maintenance...................................................................................................................................................25
APPENDIX 1 PRODUCT SPECIFICATIONS........................................................................................ 27
APPENDIX 2 BIT RATE TABLE FOR REFERENCE ............................................................................ 36
APPENDIX 3 POE CONNECTION ....................................................................................................... 38
APPENDIX 4 API ID APPLICATION FOR SMS MESSAGING.............................................................. 39
APPENDIX 5 Q&A ................................................................................................................................ 41
APPENDIX 6 RECORDING TIME TABLE ............................................................................................ 42
APPENDIX 7 MICRO SD CARD COMPATIBLE LIST........................................................................... 43
1. OVERVIEW
1.1 Product Features
 Easy network setup with your iPhone / iPad
 1.3 / 2 Megapixel solution with HDTV 720p quality, allowing users to notice minor details more easily
 Solid light series featuring better overexposure prevention (Advanced Smart Light Control)
 ONVIF standard supported to simplify system integration
 POE (Power-over-Ethernet) support to eliminate the use of power cables and reduce installation costs
 External alarm I/O device connection
 IR LEDs built-in for night surveillance
 (For selected model only) Equipped with a vari-focal lens of f2.8 ~ 12mm, suitable for various monitoring environments.
 (For selected model only) WDR to increase image recognizability in overexposure and dark areas.
 (For selected model only) Zoom lens of f6.0 ~ 60mm with 10x optical zoom, 10x digital zoom and auto focus, suitable for
various monitoring environments.
 (For selected model only) Micro SD card support for video storage.
 (For selected model only) Built-in heater which can operate at temperatures as low as -40℃.
 Remote Surveillance
-- Full compatibility on iPhone & iPad, and Internet Explorer® on Windows® operating system
1.2 Package Content
or
or
or
Quick
guide
Camera
For selected models only:
Screws
Wall
Plugs
Wrenches
Bracket
Desiccant
1
Sun Shield
1.3 Cable Overview
Type A:
Type B:
RJ45 network cable
RJ45 network cable
Alarm-in
GND
Alarm-in
GND
RESET
RESET
GND
Alarm-out
GND
Alarm-out
Power cable
Power cable
Cable
Description
Power cable
Connect to DC12V power supply.
Note: The power adapter is optional.
RJ45 network cable
Connect it to the supplied RJ45 cable extender adapter for cable extension, and prepare
another RJ45 network cable with suitable length for your connection.
GND
Ground wire, used for reset default or external device connection.
Alarm-in
Reserved for connecting to an external alarm device. For details, please refer the user
manual of your alarm device.
Alarm-out
Reserved for connecting to an external alarm device. For details, please refer the user
manual of your alarm device.
RESET
Remove the insulating coating of this wire, and twist it with a ground wire together to reset
default. This will reset all parameters, including the IP address to factory default settings.
Note: Disconnect power before twisting these two wires together, and connect to
power again for reset default.
1.5 External Alarm Connection
This camera supports external I/O device connection for easy connection.
Below shows you how to connect an external device to this camera.
2
1.5 Insert a Micro SD card (For selected models only)
For local video recording, a micro SD card slot can be found on the camera. The camera doesn’t support
hot-swapping. Please insert or remove the micro SD card with power disconnected. The data originally saved in the
micro SD card (if any) will be removed after inserting it to the camera.
Note: Only selected models are equipped with a micro SD card slot for local video recording.
Please follow the directions in the below graphic to insert Micro SD card properly:
Type A:
Type B:
Note: It’s recommended to use tweezers for inserting / removing Micro SD card.
3
2. CAMERA ACCESS WITH INTERNET EXPLORER
This network camera can be accessed via Microsoft® Internet Explorer® and iPhone / iPad / Android mobile devices
with our self-developed program “EagleEyes” installed depending on different using situations.
Note: For details about accessing network cameras via iPhone / iPad / Android mobile devices, please
refer to http://www.eagleeyescctv.com.
Before using the camera, make sure you have configured the network settings, and the network connection is fine.
For network configurations, please refer to:

“ADVANCED NETWORK SETUP” downloadable from www.surveillance-download.com/user/m359a.swf if your
network environment is not wireless.
2.1 Camera Login
Step1: Open your web browser, and key in http://ipaddress:portnum in the URL address box.
For example, for the IP address 60.121.46.236 and port No. 888, please key in ”http://60.121.46.236:888” into
the URL address box, and press “Enter”.
Step2: In the login page, key in the user name and password, and enter the security code from the image below if any.
Then, click “LOGIN”.
Step3: The wizard is then started.
‧ To skip the wizard and directly access the camera live view, click “Close”.
‧ To directly access the camera live view without starting the wizard for the login next time, check “Do not start wizard at login”.
Note: If you’re prompted to install “VLC player”, “Software” and “H264 Streaming Viewer”, please
agree to proceed the installation.
Step5: When the login is successful, the live view is shown.
2.2 Control Panel Overview
Note: The buttons available depend on the user level used to log in.

Type A:
4

Type B:
Function
Icon
User Level
Description
Live
Supervisor / Power User
/ Normal User / Guest
Switch to the live view page.
DPTZ
Supervisor / Power User
/ Normal User
Backup
Supervisor / Power User
Config.
Supervisor / Power User
Switch to the DPTZ configuration page.
For details, please refer to “2.3 Digital PTZ (DPTZ) Operations” at page 6.
Enter the event record list for video playback.
For details, please refer to “2.4 Event Record Search & Playback’ at page 8.
Switch to the system configuration page, and the functions available for
“Supervisor” and “Power User” are different.
For details, please refer to “3.1 System configuration menu” at page 9.
Media Type*
--
Supervisor / Power User
/ Normal User / Guest
Select the image player from the drop-down list:
 H.264 / MPEG-4 / Motion JPEG
 QuickTime
QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime
installed in your operating system before selecting “QuickTime”. When it is
selected, you will be promoted to enter the user name and password to access
the camera.
 VLC
Live player*
--
Supervisor / Power User
/ Normal User / Guest
Select the image player from the drop-down list:
 ActiveX
 QuickTime
QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime
installed in your operating system before selecting “QuickTime”. When it is
selected, you will be promoted to enter the user name and password to access
the camera.
 VLC
Quality
--
Supervisor / Power User
/ Normal User
Click & drag the slider to select the video quality:
BASIC / NORMAL / HIGH / BEST.
Video Resolution
--
Supervisor / Power User
/ Normal User
2 megapixel model
1.3 megapixel model








Video Profile*
--
Supervisor / Power User
/ Normal User
5
Select the image resolution from the drop list:
HD1080P (1920 x 1080)
HD720P (1280 x 720)
VGA (640 x 480) or D1 (720 x 480)
QVGA (320 x 240) or CIF (352 x 288)
SXGA (1280 x 1024)
HD720P (1280 x 720)
VGA (640 x 480)
QVGA (320 x 240)
Select the pre-defined video set from the drop list. The video set could be
configured in “Config” -> “Camera” -> “Video”.
Function
Icon
User Level
Description
Supervisor / Power User
/ Normal User
Live View Size:
Click to display the image in full screen.
To exit the full screen mode, press “Esc” on your keyboard.
Full Screen
This icon appears only when the selected resolution is HD1080P, SXGA or HD720P
& VGA.
The QVGA resolution is resized to fit into the current live view size.
Double size
This icon appears only when the selected resolution is QVGA.
The current live view size is the same as the selected resolution.
Normal Size
This icon appear only when the selected resolution is SXGA or HD720P or
HD1080P.
The selected resolution is resized to fit into the current live view size.
Fit to screen
This icon appear only when the selected resolution is SXGA or HD720P or
HD1080P.
Click and hold the movable square on the left bottom corner of the live view
to move
No Scale
This icon appear only when the selected resolution is SXGA or HD720P or
HD1080P.
Snapshot
Supervisor / Power User
/ Normal User
Click to take a snapshot of the current view on a new window. Right click
on the picture and re-save it to the location you want.
Alarm Out
Supervisor / Power User
/ Normal User
Click to force your alarm-out device to work. For example, when your
alarm device is a buzzer, click this button and your buzzer will start to
sound even if there’s no alarm event.
/
Supervisor / Power User
/ Normal User
Click to zoom in / out the current image.
/
Supervisor / Power User
/ Normal User
Click to zoom in the image to the largest / zoom out the image to its
original size.
/
Supervisor / Power User
/ Normal User
Click to adjust the clearness of the video images.
DPTZ
Supervisor / Power User
/ Normal User
Click to enable digital PTZ functions with zoom-in ratio up to 16X.
Focus Zone
Supervisor / Power User
/ Normal User
Zoom-in / out*
Max. Zoom-in / out*
Focus near / far*
Click to assign the point for focus adjustment.
This function will be disabled when DPTZ is enabled.
* For selected models only
2.3 Digital PTZ (DPTZ) Operations
This camera has PTZ capability, i.e. digital PTZ (hereafter called “DPTZ”), for wide area monitoring.
STEP1: Click “DPTZ” to show the DPTZ control panel.

Type A:
6
STEP2: Select the functions when needed:
FUNCTION
Resolution
ICON
--
DESCRIPTION
Select the video resolution for the DPTZ function. Only “VGA” and “QVGA” are available.
Take snapshots
Click to take a snapshot of the current view on a new window. Right click on the picture and re-save it to the
location you want.
Alarm Out
Click to force your alarm-out device to work. For example, when your alarm device is a buzzer, click this button
and your buzzer will start to sound even if there’s no alarm event.

Type B:
FUNCTION
Moving panel
ICON
--
DESCRIPTION
When
is selected, the moving control panel will be shown to move the picture after zoom-in is
performed.
Click to take a snapshot of the current view on a new window. Right click on the picture and re-save
it to the location you want.
Take snapshots
The selected resolution is resized to fit into the current live view size.
Fit to screen
This icon doesn’t work when the selected resolution is VGA or QVGA.
Zoom in / out
/
Click
Max. zoom in / out
/
Click
once to enlarge the picture to the max zoom ratio by 16X, and click
the picture ratio to 1X.
Focus near / far
/
Click to adjust the clearness of the video images.
Focus Zone
once to enlarge the picture by 1X, and click
Click to assign the point for focus adjustment.
This function will be disabled when DPTZ is enabled.
7
once to restore the zoom ratio by 1X.
once to restore
2.4 Event Record Search & Playback
This camera can only save up to three alarm recordings.
Note: To save more recorded data, it’s recommended to use this camera with a compatible NVR.
/
Previous / Next Hour
Click to jump to the next / previous time interval in an hour, for example, 11:00 ~ 12:00 or 14:00
~ 15:00, and start playing the earliest event video clip recorded during this whole hour.
Fast Forward
Increase the speed for fast forward. Click to get 2X, 4X, 8X & 16X speed forward eventually.
Fast Rewind
Increase the speed for fast rewind. Click to get 2X, 4X, 8X & 16X speed rewind eventually.
Play
Click to play the current video clip.
Pause
Click to pause the video playback.
Stop
Click to stop the video playback.
In the pause mode, click to get one frame forward.
Step
Audio
Click to mute the playback if necessary, and click again to restore.
Click to download the current video clip to the specified path in your PC.
Download
The downloaded video can only be opened by our own video player. Please go to “General” → “Maintenance” to
download the video player, or get the player from the CD supplied with the sales package.
8
3. CAMERA CONFIGURATIONS
Users can further configure this network camera by accessing via Internet Explorer.
3.1 System configuration menu
Click “Config.” to enter the configuration page.
The functions are categorized into six menus: Network, Camera, Record Timer, Storage, Trigger and General.

For details about “Network”, please refer to “3.2 Network” at page 11.

For details about “Camera”, please refer to “3.3 Camera” at page 17.
 For details about “Record”, please refer to “3.3.5 Privacy Mask (For selected models only)
You can cover certain areas on the camera image with privacy masks.
Item
Description
Mosaic Size
Choose the mosaic size of the privacy mask.
The options are: 8×8, 32×32, and 64×64.
Privacy Mask Name
Name your privacy mask.
Function
Select “On” to enable the privacy mask function.
Mosaic
Select “ON” to have the mosaic effect.
Color
Select “ON” to color the privacy mask. In the meantime, you can’t see the mosaic effect.
Mask Color
Select the color for the privacy mask.
Transparency
Select the transparency for your privacy mask.
The options are: 0%, 25%, 50%, and 100%.
9

3.4 Record” at page 19.

For details about “Storage”, please refer to “3.5 Storage” at page 20.

For details about “Trigger”, please refer to “3.6 Trigger” at page 21.

For details about “General”, please refer to “3.7 General” at page 22.
Main Menu
Sub-Menu
Reference
Network
Network
Configure network settings.
QoS
Limit the data flow for live streaming.
DDNS
Enter DDNS information when the network type is PPPOE or DHCP.
SNTP
Synchronize your camera time with the networked computer systems.
FTP
Enter the FTP information for event notifications when “FTP” is chosen in “Trigger” →
“Trigger”.
Mail
Enter Email information for event notifications when “Email” is chosen in “Trigger” → “Trigger”.
SMS
Enter text messaging information for SMS notifications when “SMS” is chosen in “Trigger” →
“Trigger”.
Filter
Choose to permit or block the IP address(es) which can access this camera.
*Suitable for Windows-based operating system.
UPnP
Allow this camera to be detected among devices within the same network area for easy and
quick usage.
*Suitable for Apple Mac-based operating system.
Bonjour
RTP
Camera
Camera
Allow this camera to be detected among devices within the same network area for easy and
quick usage.
Set the parameters for video data transmission when you’re using multimedia other than web
broswers and Video Viewer for remote access.
1. Rename the camera.
2. Change the place where the camera name is shown on the screen.
Video
Adjust video-related settings in different video format.
Color
Adjust the color performance.
Advance
Adjust the camera parameters if necessary.
Record
Configure the record function.
Record Timer
Schedule external alarm recording.
Storage
Memory
Check the current storage capacity and clear all recorded data when needed.
Trigger
Trigger
Record
1. Enable / disable the motion detection.
2. Set the motion detection area.
3. Configure how the camera reacts for any event.
1. Select the language of the web browser.
General
General
2. Check the MAC address of the camera.
3. Lock camera access after the specified time.
Time
Set daylight saving time and the current time.
Server Log
Check the system event logs.
Online
Check the current online user(s).
Account
Google Maps
1. Create a new user account with different access privilege.
2. Modify or delete an existing user account.
Allow you to know where the network camera is.
1. Check the current firmware version and upgrade your camera.
Maintenance
2. Copy system configurations.
3. Reboot the camera.
4. Download the video player to play the recorded data.
10
3.2 Network
3.2.1 Network
You can set the network configuration of the network camera depending on your network type.
For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m359a.swf.
3.2.2 QoS
QoS, Quality of Service, is the ability to control the data flow for real-time streaming. This function is important if
your network bandwidth is insufficient and you have other devices to share the network bandwidth.
Check “QoS Enable”, and set the max. upload rate from 256 to 10240 kbps.
3.2.3 DDNS
Select “On” when the selected network type in “Network” is “PPPOE” or “DHCP”.
For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m359a.swf.
3.2.4 SNTP
SNTP (Simple Network Time Protocol) is used to synchronize your camera time with the networked computer..
Function
Description
GMT
Once users choose the time zone, the network camera will adjust the local area time of the system
automatically.
NTP Server
Simply use the default SNTP server (For example, tock.stdtime.gov.tw) or change to another server with
which users are familiar.
Sync. Period
Select “Daily” to synchronize the camera time with the network time every day or “None” to turn off this
function.
Sync
Click and the network camera will synchronize the time with the network time.
11
3.2.5 FTP
Enter the detailed FTP information and click “Save” to confirm. The information you set here will be applied
when “FTP” is selected in “Trigger” → “Trigger”.
3.2.6 MAIL
Enter the detailed e-mail information and click “Save” to confirm. The information you set here will be applied
when “Email” is selected in “Trigger” → “Trigger”.
Function
Description
SMTP Server
Enter the SMTP server address provided from your e-mail system supplier.
Port
Enter the port number provided from your e-mail system supplier. If this column is left blank, the e-mail server will use
port 25 to send e-mails.
Mail From
Enter the name of the sender.
SSL Encryption
Select “Yes” if your e-mail server is using SSL encryption to protect your e-mail content from unauthorized access.
Verify Password
Some mail servers are required to verify the password. Please enter the “user name” and “password”.
E-Mail Address List
Add the e-mail address(s) of the assigned recipient(s).
Test
When all information is entered, click “Test Mail” to try if the receipt.
12
3.2.7 SMS
Note: Before using this function, you need to apply an account and get an API ID from the mobile
messaging company, such as Clickatell and EVERY8D. For details, please refer to “APPENDIX 4
API ID APPLICATION FOR SMS MESSAGING” at page 39.
Enter the detailed information needed for text messaging, and click “Save” to confirm. The information you set
here will be applied when “SMS” is selected in “General” → "Trigger".
Function
Description
System
The text messaging service provider is Clickatell.
User name / Password
Enter the account user name and password you created in Clickatell.
API ID
Enter the API ID you applied from Clickatell.
Recipient
Click “Add” to enter the phone number, including the country code, to receive the text
message. Five sets of phone numbers are allowed.
Transfer Interval
Set the interval time in minutes between two-message sending.
The options are 0, 15, 30 & 60.
Reset Counter
Click to restart the text messaging, and the SMS will be sent after the specified time interval
since you click this button.
Message
Enter the text content (up to 70 characters) you want to send with the text message.
Test
To know whether your SMS setting is correct, click this button to immediately send a SMS to
your phone.
Note: This testing is not free and you will be charged for SMS sending base on your
local rate.
13
3.2.8 Filter
Choose to permit or block the IP address(es) which can access this camera, and click “Save” to confirm.
Function

Description
Filter Configuration
Error Count
Set the maximum count for login failure. When the maximum count is reached, the IP address trying to access the
network camera will be locked.
Error Lock Time
Set the lock time in minutes when the maximum count of error login for an IP address is reached.
Echo Request
Select “Non-Block” to allow other users to use the ping command to detect the IP address of your network camera, or
“Block” to deny the ping command request.

IP/MAC Filter Configuration
IP/MAC Filter
Choose to enable or disable the filter function.
IP/MAC Filter Policy
If “Enable” is selected, choose whether you want to permit (Allow) or block (Deny) the IP address list below.

IP/MAC Filter Rules
‧
‧
Rule
To add an item to the IP address list, key in the IP address in “Rule”, and click “Add”.
To remove an existing item in the IP address list, click the item you want to remove, and click “Delete”.
3.2.9 UPnP / Bonjour
“UPnP” stands for “Universal Plug and Play”, which allows devices to connect seamlessly in the home and
corporate environments and simplify installation of computer components, and is only suitable for Microsoft
Windows-based operating system.
“Bonjour” functions the same as “UPnP”, but it’s only suitable for Apple Mac-based operating system.
 UPnP
 Bonjour
Check “Enable” to allow the network camera to be detected among devices within the same network area, and
set the identification name of the camera in “Friendly name”.
When this function is activated, the other PC within the same domain as this camera will be able to search this
camera in:

“Network Neighbor” with the identification name set in “Friendly name” for Windows-based PC, or

“
” (finder) or “Bookmark” with the identification name set in “Device Name” for Mac-based PC.
14
Double-click it to quickly open the web browser for camera access.
Port Mapping (Available only in UPnP)
This function can eliminate the need to additionally access the router for port forwarding.
For details, please refer to “Advanced Network Setup” from www.surveillance-download.com/user/m359a.swf.
Note: Before using this function, make sure your router supports UPnP, and this function is enabled. If
not, please access your router additionally for port forwarding.
When “Port Mapping” is set to “Enable”, the system will automatically assign an IP address or port number for
you if no IP address or port number is entered.
Note: When the configurations are saved successfully, you’ll see a message indicating the IP address
and port number assigned to this network camera.
3.2.10 RTP
The Real-time Transport Protocol (RTP) is an Internet protocol standard to manage the real-time transmission of
multimedia, such as VLC player.
The media player you want to use for remote access must support RTP transmission for this function to work
normally.
Note: When you’re about to end the remote access, please press the stop button on your media player
first, and then close the program. This is to ensure the server receives the stop command, and
also help to protect the server from redundant data transmission.

Type A
15
Function

Description
Port Range
The port range used by RTP is limited, and preserving 100 ports between the start port and end port is necessary.
Start Port
The range of the start port is 1024 ~ 65434.
End Port
The range of the end port is 1124 ~ 65534.

Multicast
Address and port for
H264 / MPEG4 /
JPEG transmission
Set a specific address and port for multicast of each stream format (H264/ MPEG4/ JPEG).
Address and port for
audio transmission
Set a specific address and port for multicast of audio.
The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.
The port for multicast must be an even number.
The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.
The port for multicast must be an even number.
Time to Live (TTL)

The range of Time to Live of the package is between 1 ~ 255. As soon as Time to Live of the
package is 0, it will be dropped.
Type B
Function

Description
Port Range
The port range used by RTP is limited, and preserving 100 ports between the start port and end port is necessary.
Start Port
The range of the start port is 1024 ~ 65434.
End Port
The range of the end port is 1124 ~ 65534.

Video
Address and port for
video transmission
Set a specific address and port for multicast of profile 1 ~ 4.
The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.
The port for multicast must be an even number.

Audio
Address and port for
audio transmission
Set a specific address and port for multicast of audio.
The range of the address is limited between 224.0.0.1 ~ 239.255.255.255.
The port for multicast must be an even number.
16
3.3 Camera
3.3.1 Camera
Rename the camera, and change the place where the camera name is shown on the screen, UP-LEFT /
UP-RIGHT / DOWN-LEFT / DOWN-RIGHT. "Snapshot Path” is used to specify the path to save snapshot files.
Type A
Type B
3.3.2 Video
Adjust video-related settings in different video format.

“Quality” is related to image clearness.

“FPS” is related to the fluency of the video. The more the FPS, the more fluent the video.

“Max Bit Rate” is the maximum limitation of data transmission in the selected image format and resolution.
Take 2 megapixel model as an example below. For 1.3 megapixel model, please refer to its actual display.
Note: QQVGA is for mobile surveillance only.

Type A:

Type B:
17
3.3.3 Color
Adjust the color performance from Brightness, Contract, Saturation, and Hue (for selected models only). Click
and drag the slider to preview the color change on the right side of ths page and adjust the image color.
To restore the default values, click “Back to Default”.
3.3.4 Advanced
Adjust the camera parameters if necessary.
Item
Description
Shutter Speed
Set the shutter speed based on your need.
The options are: Up to 1/10 sec, Up to 1/30, Up to 1/15, Up to1/6, Up to 1 and Up to 2.
Exposure Control*
This function is used to synchronize the shutter time to the fluorescent light to suppress image flickering.
Back light*
It is the function to adjust the image to compensate for an area that is overpowered by brightness because of excessive light.
The image will be properly exposed for clearness. Select to activate (ON) or disable (OFF) this function.
Note: This function is available only in the day mode.
Mirror
Select “ON” to rotate the images horizontally based on your installation situation when necessary.
Flip
Select “ON” to rotate the image 180° when necessary.
De-noise*
Click and drag the slider to adjust the level from 0 ~ 10 to decrease the noise shown in the dark environment.
IR Control
Select “Auto” to automatically enable IR LEDs at night or in the dark environment, “On” to always enable IR LEDs, or “OFF”
to disable this function.
Enhance IR
Select “On” to enhance IR LEDs performance.
IR Turn On Level
Select the level for IR light to activate.
White Balance
Process the current image to retain color balance over a color temperature range.
The options are: Auto, Incandescent Light, Cool Light, sun Light, Cloudy & Sun Shade.
Sharpness
Sharpness enhances the clarity of image detail by adjusting the aperture and sharpening the edges in the pictures.
Hold and drag the slider to adjust the level of sharpness from 0 ~ 100. The higher the value, the sharper the image.
Wide Dynamic
Range*
Wide Dynamic Range (WDR) is used when users need to increase image recognizability in overexposure and dark areas.
The options are: LOW / MIDDLE / HIGH / OFF
*Selected models only
18
3.3.5 Privacy Mask (For selected models only)
You can cover certain areas on the camera image with privacy masks.
Item
Description
Mosaic Size
Choose the mosaic size of the privacy mask.
The options are: 8×8, 32×32, and 64×64.
Privacy Mask Name
Name your privacy mask.
Function
Select “On” to enable the privacy mask function.
Mosaic
Select “ON” to have the mosaic effect.
Color
Select “ON” to color the privacy mask. In the meantime, you can’t see the mosaic effect.
Mask Color
Select the color for the privacy mask.
Transparency
Select the transparency for your privacy mask.
The options are: 0%, 25%, 50%, and 100%.
19
3.4 Record
3.4.1 Record
In “Record Configuration”, you can:
 Enable or disable the alarm record function. When “Enable” is set to “No”, the alarm record function is
disabled even if you enable it in other configuration pages.
 Select if the data should be overwritten when the memory storage is full.
 Select the video resolution for event recording.
Note: The higher resolution you choose, the more accuracy and higher image quality the recording will
be, but the faster the memory storage is consumed and become full
3.4.2 Record Timer
To schedule alarm recording, enable it, and select the day and time for recording.
Note: The timer must be enabled for the record function to work properly.
3.5 Storage
3.5.1 Memory
In “Memory”, you can check the remaining capacity for recording, or clear all recorded data saved if needed.
Note: The recorded data will be removed also when you reset or reboot this camera.
Note: To save more recorded data, it’s recommended to use this camera with the compatible NVR.
Note: To know the total recording time per recording resolution, please refer to “APPENDIX 6
RECORDING TIME TABLE” at page 42.
The total capacity may vary depending on different models. Please check the actual display of your model.
20
3.6 Trigger
3.6.1 Trigger
You can configure how this camera reacts when there’s an alarm or motion event.

Detect
Item
Description
External Alarm
Enable or disable detection from external alarm-in device, and click the title “External Alarm” (in blue) to set
or “N.C.” depending on the configuration of your alarm-in device.
Motion
Enable or disable motion detection.
Motion detection is not supported when the stream format is Motion JPEG.
When “Enable” is selected, click “Detection” to enter the motion detection area setting page as follows:
Sensitivity:
Set the detection sensitivity from the drop-down list: High, Normal or Low.
Area Setting:
Set the motion detection area by selecting the area grids with your mouse. Pink grids represent the area that is not being
detected while the transparent grids are the area under detection. You can set multiple areas under detection.
Click “Clear All” to set the whole area undetected.
Click “Select All” to set the whole area under detection.
Duration
Set the duration time for trigger recording (5 / 10 / 20 / 40 seconds).
21
“N.O.”

Action
Here defines how the camera delivers alerts to you for any event.
Item
Description
E-Mail
Select the event type you want to receive E-mail notifications when it occurs.
Then, click the title “E-Mail” (in blue) to configure the media type (H264 / JPEG / MPEG4), file format (AVC / AVI),
and record time (1 ~ 5 seconds) for the event video clip.
The camera will send the captured video clip to the E-mail address(s) you assigned in “Network”  “Mail” once the
selected event type occurs.
FTP
Select the event type you want to receive FTP notifications when it occurs.
Then, click the title “FTP” (in blue) to configure the media type (H264 / JPEG / MPEG4), file format (AVC / AVI), and
record time (1 ~ 5 seconds) for the event video clip.
The camera will upload the captured video clip to the FTP site you assigned in “Network”  “FTP” once the
selected event type occurs.
SMS*
Select the event type you want to receive a text message when it occurs.
The camera will send a text message to the mobile phone number you assigned in “Network”  “SMS” once the
selected event type occurs.
Alarm Out
Select the event type you want to trigger the alarm-out device to work when it occurs.
Then, click the title “Alarm Out” (in blue) to configure the trigger rule (LOW / HIGH).
Record
Select the event type you want to enable event recording when it occurs.
*Selected models only
3.7 General
3.7.1 General
To change the language of UI interface, select from the drop-down list in “Language”.
To lock camera access when it’s not used after the specified time, select “5 MIN”, “15 MIN” or “30 MIN” from the
drop-down list of “Auto Lock Time”, or select “NEVER” to disable this function.
Note: When the camera access is locked after the specified time, to resume camera access, please
enter the password.
3.7.2 Time
Set daylight saving time and the current time, and click “Save” to confirm.
22
Function

Description
Time Configuration
Date
Set the current date.
Time
Set the current time.

Daylight Saving Time Configuration
Daylight Saving Time
Specify whether to use daylight saving time (Enable / Disable).
If this function is enabled, set the time period (Start Time / End Time), and adjust the daylight
saving time in hours (Adjust Time).
3.7.3 Server Log
To quickly search the system logs you want by event type, click “Prev. Page” or “Next Page” to find the logs you
want, or check the event type(s) and click “Reload” to start searching.
To clear all system event logs, click “Clear All”.
3.7.4 Online
You can check the current online user(s) with respective online information. To refresh the list, click “Reload”.
 To allow anonymous login, select “Enable” in “Anonymous Viewer Login”.
 To disable image code verification at login, select “No” in “Login with CAPTCHA Image”.
23
3.7.5 Account
You can create a new account with different user access privilege, or delete or modify an existing account
setting.
How to create a new account
Step1: Click “New”, and fill in the following columns.
Column
Description
User Name
Set a user name that will be used for camera access. The user name allows up to 16 alphanumeric characters.
Password
Set the password that will be used for remote login. The password allows up to 16 alphanumeric characters.
Confirm Password
Enter the password again to confirm.
User Level
Set the security level of an account to give the permission to control different functions. There are four user levels:
SUPERVISOR, POWER USER, NORMAL USER and GUEST.
Life Time
Select how long this account is allowed to stay online (1 MIN / 5 MIN / 10 MIN / 1 HOUR / 1 DAY / INFINITE)
Step2: Then, click “Save” to save your setting and create a new account.
How to modify or delete an existing account
Step1: Select the account you want to modify or delete.
Step2: To modify the account, click “Edit” to change the settings, and click “Save”.
To remove the account, click “Delete”.
Note: It’s not allowed to remove an account when there’s only one account in the account list.
3.7.6 Google Maps
This function is used to let you know where the network camera is.
The system will prompt you to apply a Google Maps Key if your access is denied. Please follow the instructions
below when you’re denied:
Step1: Click “Sign up for a Google Maps key” to enter the application page.
Step2: Check the terms and conditions, and enter the IP address of the network camera. Then, click “Generate
API Key”.
Step3: Copy the generated API key, and click “Update Google Maps Key” on the web browser to paste it.
24
3.7.7 Maintenance
Firmware Upgrade
This function is used when users need to upgrade the camera for function scalability.
Note: Before using this function, make sure you have the correct upgrade files provided by your
installer or distributor.
Note: The event videos saved in the camera will be removed after firmware upgrade. Make sure you’ve
copied important events to your PC before firmware upgrade.
Step1: Select “ ” to browse to where you save the upgrade files, and select them one by one until all files are
selected (up to four files).
Step2: Select “Upgrade” to start system upgrading.
Note: You’ll be prompted to keep current configurations. It’s recommended to keep them, or all
configurations will be restored to default values after upgrade.
Note: It takes a few minutes to finish the upgrade process. Do not disconnect the power during
firmware upgrade, or the upgrade may be failed. The camera will reboot after the upgrade.
25
System Configuration Backup
This function is used to copy your system configuration to a “System.bin” file.
You may import the same system configuration to another camera, or restore your system configuration when
the camera is reset to default values.
Select “System.bin” in “Firmware Upgrade”, and select “Upgrade” to import the system configuration.
System Reboot
Select “Reboot” to restart your camera if needed.
Player Download
To see the event video clips downloaded to your PC, you need to first install our own video player in your PC.
Select “Free Download” to download the video player, and double click the file to install it.
26
APPENDIX 1 PRODUCT SPECIFICATIONS
Model 1
Model 2
▓ Network
LAN Port
YES
LAN Speed
Supported Protocols
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP,
RTCP,IPv4, Bonjour, UPnP, DNS,UDP,IGMP, QoS
Number of Online Users
10
ONVIF Compatible
YES
Security
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
Remote Access
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
▓ Video
Video Compression
Resolution
H.264 / MPEG4 / MJPEG
1080P, SXGA, 720P, VGA, QVGA
SXGA, 720P, VGA, QVGA
Frame Rate
30fps
Multiple Video Streaming
4 (H.264, MJPEG, MPEG4)
▓ General
Image Sensor
1/2.9" SONY CMOS image sensor
Min Illumination
1 Lux / F1.4, 0 Lux (LED ON)
S/N Ratio
More than 48dB (AGC off)
Electronic Shutter
1/2 to 1/10,000 sec
Lens
Viewing Angle
1/4" SONY CMOS image sensor
f2.8 ~ 12mm / F1.4 ~ F2.8
Wide: 109° (Horizontal) / 76° (Vertical) /
116° (Diagonal)
Tele: 24° (Horizontal) / 13.5° (Vertical) /
27° (Diagonal)
IR LED
Wide: 66° (Horizontal) / 52° (Vertical) /
90° (Diagonal)
Tele: 16° (Horizontal) / 10° (Vertical) /
22° (Diagonal)
2 Units
Default : up to 25 meters
IR Enhanced Mode : up to 35 meters
IR Effective Range **
IR Shift
YES
IRIS Mode
AES
White Balance
ATW
AGC
Auto
WDR
NO
POE (Power-over-Ethernet)
YES (IEEE 802.3af)
External Alarm I/O
YES (1 input / 1 output)
Micro SD Card Slot
YES
Heater
NO
IP Rating
IP66
Operating Temperature
-20℃~40℃
Power Source (±10%)
Power Consumption (±10%)
12V / 1.5A
PoE & PoN: 11.8W; DC Adapter: 9.5W (IR On) PoE & PoN: 13.8W; DC Adapter: 11W (IR On)
▓ Others
Mobile Surveillance
iPad / iPhone / Android mobile device
Event Notification
FTP / Email / SMS
Digital Pan / Tilt / Zoom
YES
Motion Detection
YES
RTC (real-time clock)
YES
Minimum Web Browsing Requirements
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
* The specifications are subject to change without notice. ** Dimensional tolerance: ± 5mm
27
Model 3
▓ Network
LAN Port
LAN Speed
YES
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP,
RTCP,IPv4, Bonjour, UPnP, DNS,UDP,IGMP, QoS
10
YES (Profile S)
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
Supported Protocols
Number of Online Users
ONVIF Compatible
Security
Remote Access
▓ Video
Video Compression
Resolution
Frame Rate
Multiple Video Streaming
▓ General
Image Sensor
Min Illumination
S/N Ratio
Electronic Shutter
Lens
H.264 / MPEG4 / MJPEG
1080P, SXGA, 720P, VGA, QVGA
SXGA, 720P, VGA, QVGA
30fps
4 (H.264, MJPEG, MPEG4)
1/2.9” SONY CMOS image sensor
1/4” SONY CMOS image sensor
1 Lux / F1.4, 0 Lux (LED ON)
More than 48dB (AGC off)
1/2 to 1/10,000 sec
f2.8 ~ 12mm / F1.4 ~ F2.8
Wide: 109° (Horizontal) / 76° (Vertical) /
Wide: 66° (Horizontal) / 52° (Vertical) /
90° (Diagonal)
116° (Diagonal)
Tele: 16° (Horizontal) / 10° (Vertical) /
Tele: 24° (Horizontal) / 13.5° (Vertical) /
27°(Diagonal)
22°(Diagonal)
2 Units
Default : up to 25 meters
IR Enhanced Mode : up to 35 meters
YES
AES
ATW
Auto
NO
YES (IEEE 802.3at)
Viewing Angle
IR LED
IR Effective Range **
IR Shift
IRIS Mode
White Balance
AGC
WDR
POE (Power-over-Ethernet)
External Alarm I/O
MicroSD Card Slot
Heater
IP Rating
Operating Temperature
Power Source (±10%)
Current Consumption
Model 4
YES (1 input / 1 output)
YES
YES
IP66
-40℃ ~ 40℃
12V / 1.5A
PoE & PoN: 19.5W; DC Adapter: 16.6W (IR On) PoE & PoN: 18.6W; DC Adapter: 15.8 (IR On)
▓ Others
Mobile Surveillance
Event Notification
Digital Pan / Tilt / Zoom
Motion Detection
RTC (real-time clock)
Minimum Web Browsing Requirements
(6)
iPad / iPhone / Android mobile device
FTP / Email / SMS
YES
YES
YES
(3) Intel core i3 or higher, or equivalent AMD
(4) 2GB RAM
(5) AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
The specifications are subject to change without notice.
** Dimensional tolerance: ± 5mm
28
Model 5
▓ Network
LAN Port
LAN Speed
Supported Protocols
Number of Online Users
ONVIF Compatible
Security
Remote Access
YES
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4,
Bonjour, UpnP, DNS,UDP,IGMP, QoS
10
YES (Profile S)
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
▓ Video
Video Compression
Resolution
Frame Rate
H.264 (Main Profile) / MJPEG
1080P to CIF
30/25 fps
Multiple Video Streaming
▓ General
Image Sensor
Min Illumination
S/N Ratio
Electronic Shutter
Lens
Viewing Angle
IR LED
IR Effective Range**
IR Shift
Smart Light Control
IRIS Mode
White Balance
AGC
WDR
POE (Power-over-Ethernet)
External Alarm I/O
MicroSD Card Slot
Privacy Mask
Heater
IP Rating
Operating Temperature
Power Source (±10%)
Power Consumption (±10%)
Model 6
4 (H.264, MJPEG)
1/2.8” CMOS image sensor
0.1 Lux / F1.4(Wide)~F2.8(Tele), 0 Lux (LED ON)
More than 48dB (AGC off)
1/10,000 ~ 1/7.5 (Slow shutter)
f2.8 ~ 12mm / F1.4 ~ F2.8
Wide: 97.4° (Horizontal) / 58.1° (Vertical) / 111.7° (Diagonal)
Tele: 27.1° (Horizontal) / 15.2° (Vertical) / 31.1°(Diagonal)
2 Units
Default : up to 25 meters
IR Enhanced Mode : up to 35 meters
YES
YES
AES
ATW
Auto
YES
YES (IEEE 802.3af)
YES (IEEE 802.3at)
YES (1 input / 1 output)
YES
YES
NO
YES
IP66
-20℃~40℃
-40℃~40℃
12V / 1A
12V / 2A
PoE & PoN: 10.5W; DC Adapter: 8.4W
PoE & PoN: 23.5W; DC Adapter: 20W
▓ Others
Mobile Surveillance
Event Notification
Digital Pan / Tilt / Zoom
Motion Detection
RTC (real-time clock)
Minimum Web Browsing Requirements
iOS & Android
FTP / Email / SMS
YES
YES
YES
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
*The specifications are subject to change without notice
**Using IR enhanced mode and slow shutter speed, the distance can be extended even longer.
29
Model 7
▓ Network
LAN Port
LAN Speed
Supported Protocols
Number of Online Users
ONVIF Compatible
Security
Remote Access
Model 8
YES
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4,
Bonjour, UPnP, DNS,UDP,IGMP, QoS
10
YES (Profile S)
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
▓ Video
Video Compression
Resolution
Frame Rate
Multiple Video Streaming
▓ General
Image Sensor
Min Illumination
S/N Ratio
Electronic Shutter
Lens
Viewing Angle
IR LED
IR Effective Range**
IR Shift
IRIS Mode
POE
WDR
External Alarm I/O
Heater
IP Rating
White Balance
AGC
Operating Temperature
Power Source (±10%)
Power Consumption
Model 9
H.264 (Main Profile) / MJPEG
1080P to CIF
30fps
4 (H.264, MJPEG)
1/2.9" SONY CMOS image
sensor
1/2.8" SONY CMOS image sensor
0.1 Lux / F2.0 (wide)~F2.8(Tele),
1 Lux / F2.0, 0 Lux (LED ON)
0 Lux (LED ON)
More than 48dB (AGC off)
1/7.5 to 1/8000 sec
1/10,000 ~ 1/7.5 (Slow shutter)
f6.0 ~ 60mm / F2.0 ~ 2.8
10X Optical Zoom, Auto Focus,
Near focus limit 10cm (wide) or 80cm (tele) to infinity
1X: 47.3° (Horizontal) x 27.5° (Vertical) x 53.5° (Diagonal)
10X: 5.3° (Horizontal) x 3.0° (Vertical) x 6.1° (Diagonal)
YES
Default mode: up to 40 meters
IR enhanced mode: up to 60 meters
YES
YES (Two stage)
AES
YES (IEEE 802.3af)
YES (IEEE 802.3at)
-YES
YES (1 input / 1 output)
NO
YES
IP67
ATW
Auto
-10℃~40℃
-20℃~40℃
-40℃ ~ 40℃
12V / 1A
12V / 1.5A
12V / 2A
PoE
&
PoN: 28.5W;
DC Adapter: 9W (Max)
DC Adapter: 24W
▓ Others
Mobile Surveillance
Event Notification
Digital Pan / Tilt / Zoom
Motion Detection
RTC (real-time clock)
Minimum Web Browsing Requirements
iPad / iPhone / Android mobile device
FTP / Email / SMS
YES
YES
YES
‧Intel core i3 or higher, or equivalent AMD
‧2 GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
* The specifications are subject to change without notice.
** Dimensional tolerance: ± 5mm
30
Model 10
▓ Network
LAN Port
LAN Speed
Supported Protocols
Number of Online Users
ONVIF Compatible
Security
Remote Access
YES
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4,
Bonjour, UPnP, DNS,UDP,IGMP, QoS
10
YES (Profile S)
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
▓ Video
Video Compression
Resolution
Frame Rate
H.264 / MJPEG
1080P to CIF
30fps
Multiple Video Streaming
▓ General
Image Sensor
Min Illumination
S/N Ratio
Electronic Shutter
Lens
Viewing Angle
IR LED
IR Effective Range**
IR Shift
Smart Light Control
IRIS Mode
White Balance
AGC
WDR
Privacy Mask
POE (Power-over-Ethernet)
External Alarm I/O
MicroSD Card Slot
Heater
IP Rating
Operating Temperature
Power Source (±10%)
Power Consumption (±10%)
Model 11
4 (H.264, MJPEG)
1/2.8” CMOS image sensor
1/10,000 ~ 1/7.5 (Slow shutter)
More than 48dB (AGC off)
1/2 to 1/10,000 sec
f2.8 ~ 12mm / F1.4 ~ F2.8
Wide: 97.4° (Horizontal) / 58.1° (Vertical) / 111.7° (Diagonal)
Tele: 27.1° (Horizontal) / 15.2° (Vertical) / 31.1°(Diagonal)
2 Units
Default : up to 25 meters
IR Enhanced Mode : up to 35 meters
YES
YES
AES
ATW
Auto
YES
YES
YES (IEEE 802.3af)
YES (IEEE 802.3at)
YES (1 input / 1 output)
YES
NO
YES
IP66
-20℃ ~ 40℃
-40℃ ~ 40℃
12V / 1A
12V / 2A
PoE & PoN: 10.5W; DC Adapter: 8.4W
PoE & PoN: 23.5W; DC Adapter: 20W
▓ Others
Mobile Surveillance
Event Notification
Digital Pan / Tilt / Zoom
Motion Detection
RTC (real-time clock)
Minimum Web Browsing Requirements
iOS & Android
FTP / Email / SMS
YES
YES
YES
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
*The specifications are subject to change without notice
**Using IR enhanced mode and slow shutter speed, the distance can be extended even longer.
31
Model 12
▓ Network
LAN Port
LAN Speed
Supported Protocols
Number of Online Users
ONVIF Compatible
Security
Remote Access
YES
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4,
Bonjour, UPnP, DNS,UDP,IGMP, QoS
10
YES (Profile S)
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
▓ Video
Video Compression
Resolution
Frame Rate
H.264 / MPEG4 / MJPEG
1080P, SXGA, 720P, VGA, QVGA
30fps
Multiple Video Streaming
▓ General
Image Sensor
Min Illumination
S/N Ratio
Electronic Shutter
Lens
Viewing Angle
IR LED
IR Effective Range**
IR Shift
Smart Light Control
IRIS Mode
White Balance
AGC
WDR
POE (Power-over-Ethernet)
External Alarm I/O
MicroSD Card Slot
Heater
IP Rating
Operating Temperature
Power Source (±10%)
Power Consumption (±10%)
Model 13
4 (H.264, MJPEG, MPEG4)
1/2.9" CMOS image sensor
1 Lux / F1.4, 0 Lux (IR LED ON)
More than 48dB (AGC off)
1/2 to 1/10,000 sec
f2.8 ~ 12mm / F1.4 ~ F2.8
Wide: 109° (Horizontal) / 76° (Vertical) / 116° (Diagonal)
Tele: 24° (Horizontal) / 13.5° (Vertical) / 27°(Diagonal)
2 Units
Default : up to 25 meters
IR Enhanced Mode : up to 35 meters
YES
NO
AES
ATW
Auto
NO
YES (IEEE 802.3af)
YES (IEEE 802.3at)
YES (1 input / 1 output)
YES
NO
YES
IP66
-20℃ ~ 40℃
-40℃ ~ 40℃
12V / 1A
12V / 2A
PoE & PoN: 12.5W; DC Adapter: 10.25W
PoE & PoN: 25W; DC Adapter: 21.1W
▓ Others
Mobile Surveillance
Event Notification
Digital Pan / Tilt / Zoom
Motion Detection
RTC (real-time clock)
Minimum Web Browsing Requirements
iOS & Android
FTP / Email / SMS
YES
YES
YES
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
*The specifications are subject to change without notice
**Using IR enhanced mode and slow shutter speed, the distance can be extended even longer.
32
Model 14
▓ Network
LAN Port
LAN Speed
Supported Protocols
Number of Online Users
ONVIF Compatible
Security
Remote Access
▓ Video
Video Compression
Resolution
Frame Rate
Multiple Video Streaming
▓ General
YES
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4,
Bonjour, UPnP, DNS,UDP,IGMP, QoS
10
YES (Profile S)
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
H.264 (Main Profile) / MJPEG
1920 x 1080 / 1280 x 720 / 720 x 480 / 352 x 288
30fps
4 (H.264, MJPEG)
Image Sensor
1/2.8" SONY CMOS image sensor
Min Illumination
0.1 Lux / F1.4(Wide)~F2.8(Tele), 0 Lux (IR LED ON)
Shutter Speed
1/10,000 ~ 1/7.5 (Slow shutter)
S/N Ratio
More than 48dB (AGC off)
Lens
f2.8 ~ 12mm / F1.4 ~ F2.8
Viewing Angle
Wide: 97.4° (Horizontal) / 58.1° (Vertical) / 111.7° (Diagonal)
Tele: 27.1° (Horizontal) / 15.2° (Vertical) / 31.1°(Diagonal)
IR LED
2 units
Default : up to 25 meters
IR Enhanced Mode : up to 35 meters
IR Effective Distance**
IR Shift
YES
Smart Light Control
YES
White Balance
ATW
AGC
Auto
IRIS Mode
AES
WDR
YES
Privacy Mask
YES
POE
YES (IEEE 802.3af)
External Alarm I/O
YES (1 input / 1 output)
MicroSD Card Slot
YES (up to 64GB)
IP Rating
IP66
Operating Temperature
-20℃ ~ 50℃
Power Source (±10%)
DC12V / 1A
Current Consumption (±10%)
700mA
Power Consumption (±10%)
10.5W (PoE); 10.5W (PoN) ; 8.4W (DC Adapter)
▓ Others
Mobile Surveillance
iOS & Android mobile devices
Event Notification
FTP / Email / SMS
Digital Pan / Tilt / Zoom
YES
Motion Detection
YES
RTC (real-time clock)
YES
Minimum Web Browsing Requirements
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
*The specifications are subject to change without notice.
**By using IR enhanced mode and slow shutter speed, the distance can be extended even longer.
33
Model 15
Model 16
▓ Network
LAN Port
YES
LAN Speed
Supported Protocols
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4,
Bonjour, UPnP, DNS,UDP,IGMP, QoS
ONVIF Compatible
YES (Profile S)
Number of Online Users
10
Security
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
Remote Access
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
▓ Video
Network Compression
Video Resolution
H.264 / MPEG4 / MJPEG
1280 x 1024 / 1280 x 720 / 640 x 480 / 320 x 240
Frame Rate
30fps
Multiple Video Streaming
▓ General
4 (H.264 / MPEG4 / MJPEG)
Image Sensor
1/ 3” SONY CMOS image sensor
Min Illumination
1 Lux / F1.5, 0 Lux (IR LED ON)
Shutter Speed
1/2 to 1/10,000 sec
S/N Ratio
More than 48dB (AGC off)
Lens
Viewing Angle
f3.8mm / F1.5
65.4° (Horizontal) / 49.9° (Vertical) / 80.4° (Diagonal)
IR LED
2 units
Default : up to 25 meters
IR Enhanced Mode : up to 35 meters
IR Effective Distance**
IR Shift
YES
White Balance
ATW
AGC
Auto
IRIS Mode
AES
POE
YES (IEEE 802.3af)
External Alarm I/O
YES (1 input / 1 output)
MicroSD Card Slot
Heater
YES (up to 64GB)
NO
IP Rating
Operating Temperature
YES
IP66
-20℃~50℃
Power Source (±10%)
-40℃~50℃
DC12V / 1A
Current Consumption (±10%)
627mA max
1.32mA (IR Enhanced Mode ON + Heater ON)
Power Consumption (±10%)
9.74W (PoE) ; 9.74W (PoN) ; 8.28W max (DC
Adapter)
20.5W (PoE) ; 20.5W (PoN) ; 17.42W max (DC Adapter)
▓ Others
Mobile Surveillance
iOS & Android mobile devices
Event Notification
FTP / Email / SMS
Digital Pan / Tilt / Zoom
YES
Motion Detection
YES
RTC (real-time clock)
YES
Minimum Web Browsing Requirements
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
34
Model 17
Model 18
▓ Network
LAN Port
YES
LAN Speed
Supported Protocols
10/100 Based-T Ethernet
DDNS, PPPoE, DHCP, NTP, SNTP, TCP/IP, ICMP, SMTP, FTP, HTTP, RTP, RTSP, RTCP,IPv4,
Bonjour, UPnP, DNS,UDP,IGMP, QoS
ONVIF Compatible
YES (Profile S)
Number of Online Users
10
Security
(1) Multiple user access levels with password
(2) IP address filtering
(3) Digest authentication
Remote Access
(1) Internet Explorer on Windows operating system
(2) 16CH Video Viewer on Windows & MAC operating system
(3) EagleEyes on iPhone, iPad & Android mobile devices
▓ Video
Network Compression
H.264 / MPEG4 / MJPEG
Video Resolution
1920 x 1080 / 1280 x 720 / 640 x 480 / 320 x 240
Frame Rate
30fps
Multiple Video Streaming
▓ General
4 (H.264 / MPEG4 / MJPEG)
Image Sensor
1/2.9" SONY CMOS image sensor
Min Illumination
0.1 Lux / F1.5, 0 Lux (LED ON)
Shutter Speed
1/2 to 1/10,000 sec
S/N Ratio
More than 48dB (AGC off)
Lens
Viewing Angle
f3.8mm / F1.5
73.2° (Horizontal) / 42.8° (Vertical) / 83.2° (Diagonal)
IR LED
2 units
Default : up to 25 meters
IR Enhanced Mode : up to 35 meters
IR Effective Distance**
IR Shift
YES
White Balance
ATW
AGC
Auto
IRIS Mode
AES
POE
YES (IEEE 802.3af)
External Alarm I/O
MicroSD Card Slot
Heater
YES (1 input / 1 output)
YES (up to 64GB)
NO
YES
IP Rating
IP66
Operating Temperature
-20℃ ~ 50℃
-40℃~50℃
Power Source (±10%)
DC12V / 1A
DC12V / 2A
630mA (LED ON)
1.335A (IR Enhanced Mode ON + Heater ON)
10W (PoE); 10W (PoN) ; 8.5W (DC Adapter)
20.73W Max (PoE); 20.73W (PoN) ; 17.62W max
(DC Adapter)
Current Consumption (±10%)
Power Consumption (±10%)
▓ Others
Mobile Surveillance
iOS & Android mobile devices
Event Notification
FTP / Email / SMS
Digital Pan / Tilt / Zoom
YES
Motion Detection
YES
RTC (real-time clock)
YES
Minimum Web Browsing Requirements
‧Intel core i3 or higher, or equivalent AMD
‧2GB RAM
‧AGP graphics card, Direct Draw, 32MB RAM
‧Windows 7, Vista & XP, DirectX 9.0 or later
‧Internet Explorer 7.x or later
*The specifications are subject to change without notice.
**By using IR enhanced mode and slow shutter speed, the distance can be extended even longer.
35
APPENDIX 2 BIT RATE TABLE FOR REFERENCE
The data below is for reference only.
The bit rates listed here may vary depending on the resolution, image quality & frame rate you choose, the
complexity of your monitoring area, and how often the moving objects show in your monitoring area.
Testing Environment



Place: Office Entrance
Network translation: H.264
Camera type: Megapixel camera
Static: No one coming in and out
Dynamic: One or two people coming in and out
Resolution
Quality
Frame Rate
(Dynamic) kbps
(Static) kbps
SXGA
Best
FULL
3253
3216
High
2375
2160
Normal
1571
1266
Basic
1465
873
Best
2010
1261
High
1042
1034
Normal
685
572
Basic
457
350
Best
646
366
High
482
350
Normal
302
286
Basic
168
161
1163
1076
High
989
715
Normal
855
534
Basic
719
443
Best
789
571
High
451
447
Normal
349
237
Basic
217
165
Best
269
147
High
182
131
Normal
164
113
Basic
97
71
VGA
QVGA
SXGA
VGA
QVGA
Best
1/4
36
Resolution
Quality
Frame Rate
(Dynamic) kbps
(Static) kbps
SXGA
Best
1/15
581
374
High
405
342
Normal
487
248
Basic
337
141
Best
358
79
High
201
63
Normal
180
28
Basic
92
15
Best
111
84
High
99
68
Normal
97
54
Basic
58
42
VGA
QVGA
37
APPENDIX 3 POE CONNECTION
This device supports PoE (Power-over-Ethernet), developed by the IEEE802.3af or IEEE802.3at task force, and
power can be supplied over the same network (Ethernet) cable as the one used to connect to Internet. No power
cable is needed. Below shows two examples of POE application for reference.

When your router / hub supports POE connection

When your router / hub doesn’t support POE connection (An optional POE connected required)
38
APPENDIX 4 API ID APPLICATION FOR SMS MESSAGING
To allow the camera automatically sending a text message when an event happens, you need to
apply an API ID from a mobile messaging company first, such as Clickatell or EVERY8D.
Below shows an example of how to get an API ID from Clickatell.
Note: The SMS messaging may not be totally free. Please check the charge policy of the
messaging service you use.
Note: The instructions below are for reference only and may vary when Clickatell’s
official website is updated.
Please follow the steps below for application.
Step1: Go to http://www.clickatell.com/login.php. Sign up an account first.
Step2: Select “Developers Central”, select the location where you want to use this service, and fill in
your information to create an account.
Step3: When the account is created, the system will automatically send an Email to your specified
Email address with the user name, password, and client ID used to log into the service.
Step4: Click the link within the email to log in, and you will be prompted to validate your mobile phone
number. Select “SEND ACTIVATION CODE”. The system will send an activation code to that
number for verification.
Check if you receive a text message from Clickatell, and enter the activation code.
39
Step4: In your account, find “Connection Status” and create a connection (API ID).
Step5: Select “HTTP/S”.
Give a meaning name for this connection, and click “Submit and Get API ID”.
Step5: An API ID will be generated as follows.
Note: Note down the API ID for SMS notification setting later.
40
APPENDIX 5 Q&A
For more details about Q&A, please visit our official website: www.eagleeyescctv.com
Question
Answer
I can connect to this camera in my
house or office where it’s installed
with wireless network.
You didn’t configure this camera to Internet, but only in LAN.
But when I leave my house or office, I
can’t connect to it from my mobile
phone (with 3G network), or other PC
(connected to Internet). Why?
My live images are not fluent. Why?
Please follow the steps in the advanced network setup guide
downloadable from www.surveillance-download.com/user/m359a.swf to
complete network configurations, or it’s recommended for you to check
with your local installer or reseller for this service because it’s usually hard
for a person who doesn’t have network knowledge to set network
configurations.
Image fluency could be affected by the local network upload bandwidth,
router efficiency, client network download bandwidth, complexity of live
view, and more.
(Recommended) To have the best image fluency, select QVGA; to have
the best image quality, select “SXVGA” based on the model you have; to
have normal image fluency and quality, select “VGA”.
Please try adjusting the power line frequency to “60 Hz” or “50 Hz” for the
camera.
The live video keeps flickering. Why?
For iPhone users, access the camera, and select “
” on the top right
corner to enter IPCAM Configuration page. Then, go to “Advance Setup”
 “Camera” to change setting.
For access from Internet Explorer, log into the camera, and select
“Config.”  “Camera”  “Camera”.
41
APPENDIX 6 RECORDING TIME TABLE
Below shows the estimated total recording time for each recording resolution.
The recording time per resolution is the average value collected from the both alarm trigger conditions indicated in
“Testing Environment”, and is for reference only.
The time may vary depending on the resolution, image quality & frame rate you choose, the complexity of your
monitoring area, and how often the moving objects show in your monitoring area.
Testing Environment
 Place: Office
 Monitoring area: 1.5 meters away from the camera
 Alarm trigger conditions:
(1) One person walks by the monitoring area and leaves immediately.
(2) Two persons walk by the monitoring area. One goes away immediately, and the other one stays a while and
goes away.
Recording Resolution Recording time (second) SXGA VGA QVGA 25 115 211 42
APPENDIX 7 MICRO SD CARD COMPATIBLE LIST
Manufacturer
Capacity
Class
Manufacturer
Capacity
Class
ADATA
2GB
--
Transcend
2GB
--
4GB
Class 6
4GB
Class 2
2GB
--
4GB
Class 4
4GB
Class 4
4GB
Class 6
2GB
--
8GB
Class 6
4GB
Class 4
16GB
Class 10
8GB
Class 4
2GB
--
16GB
Class 4
4GB
Class 4
32GB
Class 4
8GB
Class 4
2GB
--
32GB
Class 4
4GB
Class 4
64GB
Class 10
16GB
Class 10
TOSHIBA
16GB
Class 4
Silicon Power
64GB
--
TOPRAM
32GB
Class 10
Kingmax
64GB
--
Apacer
SanDisk
Verico
Kingston
43
Download PDF