User manual - G100 stabilizer

G100
1 Beginner Guide
FEIYU-EN-3
Please upgrade the firmware to V1.13 or above version.
Insert The Batteries
Install The Camera
Remove the power switch
cap, insert two 18350
batteries into the handle.
Install the GoPro camera by the
special Thumb Screw. And make
sure it is fixed well.
Working Mode Instructions
Use for switch
the working
mode and
realize other
function
Heading Follow Mode Camera Pitch and Roll Angles remain
The working mode and function
can be identified by the LED status
Attention ! Please install the suitable camera first before power on the Gimbal.
R
Function Button
constant, heading follows the handheld position.
Heading And Pitch Follow Mode Camera Roll Angle remains
constant. Heading and Pitch follow the handheld position.
Heading Lock Mode Heading, Pitch and Roll are all locked to
point at one position.
Confirm the camera is
installed well,then press
the power button to turn
on the Gimbal.
L
Manual Pulling Locking
The pitching can be adjusted 8 seconds after the Gimbal has been started. Within the Heading Follow and Heading
Lock Mode the pitching can be adjusted to the desired angle manually, wait in this position up to 0.5 second until the current angle is adjusted.
Installation
Method
Reset
Four press the function button in succession within any working mode, the gimbal will reset to the original state.
Level Calibration
The pitch and roll angle can be adjusted to level by G100 Remote Control without connect to the computer. Details of the
operation please refer to chapter 6
Please choose one way
to install the GoPro camera
Heading Follow Speed Mode Configuration
The follow speed of the heading can be configurate by G100 Remote Control without
connect to the computer. Details of the operation please refer to chapter 6
Function Button Instructions
When the Gimbal is working, you
can press the function button to
switch among the three working
modes and a special working
condition freely.
(Details of working modes please refer
to the instructions of working modes)
2 Product Appearance Instructions
Pitch Axis
Roll Axis
M2 Knurled
Thumb Screw
Video Input
And
Camera
Charging
Interface
Heading Axis
Function
Interface
Function
Button
Power
Switch
If any comments or suggestions please do not hesitate
to e-mail us directly : service@feiyu-tech.com
Heading
Special Working Condition (Inversion Mode)
When in any working mode, press the function button for three times in succession, the
Gimbal enter into the inversion mode and switch to the Heading following mode automatically. Invert the Gimbal to capture more excited
scenes easily by switching mode combination. When in inversion working condition press the function button for three times in succession to reset
the Gimbal back to the original state.
Standby Mode
Press the function button for 3 seconds, then the motor will stop working and the LED of the function button will light constantly.
This indicates that the Gimbal is in the standby mode. Single press the function button the Gimbal will be awakened immediately.
Mode Switching
Power On
Roll
FY-G100 is suitable for GoPro 4/GroPro 3+/GroPro 3, also can be compatible
with GoPro LCD backpack and the cameras with the same size.
3 Operation Instructions
Pitch
3-axis
EN
Operation
LED Status
Function Explanation
Operation Again
Single Press
Single Flashes
Heading Follow Mode
Other operation is arbitrary
Function Of Operation Again
Double Press
Double Flashes
Heading And Pitch Follow Mode
Other operation is arbitrary
Three Press
Single Flashes
Inversion Mode
Three Press again
Four Press
Single Flashes
Reset
Other operation is arbitrary
Long Press
For 1 Second
On Constantly
Heading Lock Mode
Other operation is arbitrary
Long Press
For 3 Second
On Constantly
Standby Mode
Single press again
4 Standard And Optional Accessories
Exit standby mode ,
and awaken immediately
Correct Method For Using USB Data Cable
USB
Standard Accessories
Exit inversion mode to original state
!
Please refer to the method of proper usage
mentioned below. Otherwise the device
itself or other equipment can be damaged
Battery Charging: Put the Mini-USB terminal of the USB
Mini-USB
Indicator
Charger
Indicator Explanation
Type: 16340/18350
LED Status
Explain
Input: DC 5V Min 800mA
Blue light flashes
three times
Full Power
Output: DC 4.2V
Blue light flashes
twice
Enough Power
Blue light flashes
once
Low Power
Blue light keeps
flashing
No Power
If the indicator light flashes red,
the Gimbal will not work correctly
due to an error.
Rechargeable
Battery
Type: 18350
USB Cable
Extension Knurled
Thumb Screw
cable into the Mini-USB interface of the charger and the
USB terminal to the power adapter, if needed connect to
the EN Connector.
Connect The Computer: Please remove the batteries first,
then insert the Mini-USB terminal into the function interface on the
Gimbal and the USB terminal to the USB connector. Afterwards
connect the device with the computer to do firmware updates or
parameter configuration. (Please connect the USB cable to the
computer with the USB connector, otherwise the interface of
the computer will be damaged ).
Further information can be found in the chapter of the
Function Interface Instructions.
Charging cable
Optional Accessories
Name
Remote
Control
Video Output cable
Battery
Extender
Extension Bar
Power Adapter
European Standard
Connector
USB Connector
Function Description
Realize the heading & pitch angle adjustment,
mode switching, level calibration and heading
follow speed configuration from a distance.
Extend the capacity space for battery to
make the runtime longer.
Spiral design of the extension bar can be
perfect combination with G4 power switch;
Extended length is optional, it will help to
enjoy a different visual easily.
Camera
Charging Cable
The Gimbal can power supply for the Gopro
camera.
Video Output
Cable
Through this cable the analog video signal of
the Gopro camera will be send to the function
interface on the Gimbal.
Please connect the analoy monitor for displaying
5 Function Interface Instructions
!
8 Extension Bar Instructions (Optional Item)
With the special designed switch, the extension bar can be added directly. Allows to shoot the distance
images more easily. Special design allows for flexible extension.
WARNING
WARNING
350mm
Upgrade........
Mini
Interface
USB Cable
USB Connector
Φ23mm
Please Remove
The Batteries
Before
Upgrading
PC
Attention: Make sure that the connection to the computer is done by the USB connector
Firmware Upgrade Instruction
Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest
firmware then unzip the RAR file.Remove the batteries and refer to the connection diagram to connect the gimbal with the computer.
Please refer to the manual of update operation to upgrading,otherwise the Gimbal will be abnormal.
Extension Bar Diagram
Attention : Please make sure that the connection to the computer is done by the USB connector.
Parameters Configuration
The heading follow speed can be configurate through parameter setting software.User can adjust to the desired following speed mode
according to the requirements of filming scene. Three modes for optional: “SLOW” mode, “NORMAL” mode , “FAST” mode.
Default setting is “NORMAL” mode.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Gimbal Calibration
The Gimbal attitude can be calibrated through parameter setting software. User can adjust the pitch and roll in a small angle to achieve more
accuracy filming scene. Please insert the batteries then refer to the connection diagram to connect the gimbal with the computer for calibration.
Attention : Please make sure that the connection to the computer is done by the USB connector.
6 G4 Remote Control Instructions (Optional Item)
Angle Control
Within the Heading Follow Mode , pitch angle can be controlled by the“UP”
and “DOWN”button on the G4 Remote Control.
Heading angle can be controlled by the“LEFT”and“RIGHT”button .
Function
Button
Mini
Interface
Level Calibration
Direction
Button
Remote
Control
Connect the G100 Remote Control to the
function interface, heading & pitch angle
adjustment and mode switching can be
operated from a distance.
Note: The function button on the Gimbal will
be disabled after connect the G4 Remote Control
Direction
Button
UP
LEFT
DOWN
RIGHT
Initialization Instructions
1. Install the camera properly.
2. Gimbal placed on stationary flat and keep motionless.
3. Power on the Gimbal.
4. The Gimbal is activate and it will be initialized automatically.
Afterward pick up the Gimbal start working with it.
Note:
Use of G100 Remote Control :
USB Data Cable For RC
9 Initialize The FY-G4 Gimbal
Through connect the G100 Remote Control , the gimbal can make level
calibration by RC without connect to the computer. Six press the function
button in succession within any working mode, Gimbal will enter the Level
Calibration Mode. The pitch angle can be adjusted by the“UP”and“DOWN”
button, the roll angle can be adjusted by the “LEFT” and “RIGHT” button.
After finish the level calibration , single press the function button on the RC, the
Gimbal will exit the level calibration mode then enter the standby mode and
save the parameters automatically. Single press the function button on the RC
again the gimbal will be awakened immediately.
Note: Please make sure that Gimbal initialized successfully.
Heading Following Speed Mode Configurate
Hold the“RIGHT”button and four press the function button in succession at
the same time, the Gimbal will accelerate the heading follow speed.
Hold the“LEFT”button and four press the function button in succession at the
same time, the Gimbal will slow down the heading follow speed. When
successfully configurate the heading follow mode the Gimbal will enter the
standby mode and save the parameters automatically. Single press the function
button on the RC again the Gimbal will be awakened immediately.
There are three heading follow speed modes for optional: “SLOW”mode,
“NORMAL”mode , “FAST” mode. Default setting is“NORMAL” mode.
Configuration can be done within any working mode.
7 Video And Camera Charging Interface
The LED of the function button will fast flashing
if the initialization succeed.
FY-G4 needs to be initialized whenever the
following situations appear after power on
Motionless Flat Surface
1. After power on, the angle of pitch is not level with the horizon line.
2. After power on, the angle of roll is not parallel with the horizon line.
3. When the gimbal is in heading lock, the angle of heading moves frequently (heading is not stationary).
10 Specification
Items
Min
Standard
Max
Working Voltage
6.0V
8.4V
0(Horizontal)
0(Horizontal)
17.0V
Pitch Angle
Roll Angle
-160(Down)
-50
Heading Angle
Heading Angle
+160(Up)
+50
Handheld In Horizontal
-160(Left)
+160
Handheld In Vertical
-50
+50
Handheld In Horizontal
Pitch Following Rate
Heading Following Rate
2°/ Sec
3°/ Sec
75°/ Sec
150°/ Sec
Static Attitude Tracking Accuracy
0.01
0.02
0.05
Gimbal In Static Mode
Motion Attitude Tracking Accuracy
0.1
0.2
0.5
Motor Overload<2G
Overload Current Protection
800mA
Weight
265g
FY-G100 Handheld Gimbal is an excellent camera stabilizer,lightweight and portable.
This interface can be output 5 voltage and input analog video signal of GoPro
Connect the camera charging
cable, power supply for the GoPro
camera.
Connect the video output cable, input
analog video signal of GoPro camera
and output via the function interface
on the gimbal.
Analog Monitor Cable
( Equipped By Users )
Prohibit any user for any illegal purpose. Users will be responsible for all behavior of
purchase and use products.
Analog Monitor
( Equipped By Users )
After connect the video output cable, the analog
monitor connect to the function interface for displaying.
Note: The camera charging cable and the video
output cable doesn’t includes in the standard
package, it’s a optional item.
Without Batteries & Camera
11 Attention
DISCLAIMER
Mini
Interface
Remarks
The Guilin Feiyu Electronic Technology Co.,Ltd and our associates are not
responsible for any damages or liabilities caused by the use of this product.
For any unknown sources or using, we will not be any service.
Feiyu Tech reserves the right to amend this manual and the terms and conditions
of use the gimbal at any time.
AT T E N T I O N
Please correct assemble the gimbal according
to the diagram .
Please upgrading firmware and configurate
parameters with the standard configuration
USB date cable.
Please battery charging with the standard
configuration charger.
Please install the camera well before power
on the Gimbal.
Please visit the official website of Feiyu Tech
to get related information: www.feiyu-tech.com
Download PDF