Nortel VPN Router Installation -- VPN Router 600

Version 7.05.300
NN46110-308 02.01
311862-F Rev 01
November 2007
Standard
600 Technology Park Drive
Billerica, MA 01821-4130
Nortel VPN Router Installation
— VPN Router 600
2
Copyright © 2007 Nortel Networks. All rights reserved.
The information in this document is subject to change without notice. The statements, configurations, technical data, and
recommendations in this document are believed to be accurate and reliable, but are presented without express or implied
warranty. Users must take full responsibility for their applications of any products specified in this document. The
information in this document is proprietary to Nortel Networks Inc.
Trademarks
Nortel, the Nortel logo, the Globemark, and Contivity are trademarks of Nortel Networks.
Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated.
HyperTerminal is a trademark of Hilgraeve, Inc.
Intel is a trademark of Intel Corporation.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation.
Netscape and Netscape Navigator are trademarks of Netscape Communications Corporation.
All other trademarks are the property of their respective owners.
Statement of conditions
In the interest of improving internal design, operational function, and/or reliability, Nortel Networks Inc. reserves the
right to make changes to the products described in this document without notice.
Nortel Networks Inc. does not assume any liability that may occur due to the use or application of the product(s) or
circuit layout(s) described herein.
USA requirements only
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which
case users will be required to take whatever measures may be necessary to correct the interference at their own expense.
European requirements only
EN 55 022 statement
This is to certify that the Nortel Networks VPN Router 600 is shielded against the generation of radio interference in
accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application
of EN 55 022 Class A (CISPR 22).
Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, in which
case, the user may be required to take appropriate measures.
Achtung: Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in welchen Fällen der Benutzer für entsprechende Gegenmaßnahmen verantwortlich ist.
NN46110-308 02.01
3
Attention: Ceci est un produit de Classe A. Dans un environnement domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilisateur de prendre les mesures spécifiques appropriées.
EC Declaration of Conformity
This product conforms (or these products conform) to the provisions of the R&TTE Directive 1999/5/EC.
Japan/Nippon requirements only
Denan statement
Voluntary Control Council for Interference (VCCI) statement
Taiwan requirements
Bureau of Standards, Metrology and Inspection (BSMI) statement
Canada requirements only
Canadian Department of Communications Radio Interference Regulations
This digital apparatus (VPN Router 600) does not exceed the Class A limits for radio-noise emissions from digital
apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
Nortel VPN Router Installation — VPN Router 600
4
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique (VPN Router 600) respecte les limites de bruits radioélectriques visant les appareils numériques
de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des Communications du Canada.
Nortel Networks Inc. software license agreement
This Software License Agreement (“License Agreement”) is between you, the end-user (“Customer”) and Nortel
Networks Corporation and its subsidiaries and affiliates (“Nortel Networks”). PLEASE READ THE FOLLOWING
CAREFULLY. YOU MUST ACCEPT THESE LICENSE TERMS IN ORDER TO DOWNLOAD AND/OR USE THE
SOFTWARE. USE OF THE SOFTWARE CONSTITUTES YOUR ACCEPTANCE OF THIS LICENSE
AGREEMENT. If you do not accept these terms and conditions, return the Software, unused and in the original shipping
container, within 30 days of purchase to obtain a credit for the full purchase price.
“Software” is owned or licensed by Nortel Networks, its parent or one of its subsidiaries or affiliates, and is copyrighted
and licensed, not sold. Software consists of machine-readable instructions, its components, data, audio-visual content
(such as images, text, recordings or pictures) and related licensed materials including all whole or partial copies. Nortel
Networks grants you a license to use the Software only in the country where you acquired the Software. You obtain no
rights other than those granted to you under this License Agreement. You are responsible for the selection of the
Software and for the installation of, use of, and results obtained from the Software.
1. Licensed Use of Software. Nortel Networks grants Customer a nonexclusive license to use a copy of the Software
on only one machine at any one time or to the extent of the activation or authorized usage level, whichever is applicable.
To the extent Software is furnished for use with designated hardware or Customer furnished equipment (“CFE”),
Customer is granted a nonexclusive license to use Software only on such hardware or CFE, as applicable. Software
contains trade secrets and Customer agrees to treat Software as confidential information using the same care and
discretion Customer uses with its own similar information that it does not wish to disclose, publish or disseminate.
Customer will ensure that anyone who uses the Software does so only in compliance with the terms of this Agreement.
Customer shall not a) use, copy, modify, transfer or distribute the Software except as expressly authorized; b) reverse
assemble, reverse compile, reverse engineer or otherwise translate the Software; c) create derivative works or
modifications unless expressly authorized; or d) sublicense, rent or lease the Software. Licensors of intellectual property
to Nortel Networks are beneficiaries of this provision. Upon termination or breach of the license by Customer or in the
event designated hardware or CFE is no longer in use, Customer will promptly return the Software to Nortel Networks or
certify its destruction. Nortel Networks may audit by remote polling or other reasonable means to determine Customer’s
Software activation or usage levels. If suppliers of third party software included in Software require Nortel Networks to
include additional or different terms, Customer agrees to abide by such terms provided by Nortel Networks with respect
to such third party software.
2. Warranty. Except as may be otherwise expressly agreed to in writing between Nortel Networks and Customer,
Software is provided “AS IS” without any warranties (conditions) of any kind. NORTEL NETWORKS DISCLAIMS
ALL WARRANTIES (CONDITIONS) FOR THE SOFTWARE, EITHER EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE AND ANY WARRANTY OF NON-INFRINGEMENT. Nortel Networks is not obligated to
provide support of any kind for the Software. Some jurisdictions do not allow exclusion of implied warranties, and, in
such event, the above exclusions may not apply.
3. Limitation of Remedies. IN NO EVENT SHALL NORTEL NETWORKS OR ITS AGENTS OR SUPPLIERS BE
LIABLE FOR ANY OF THE FOLLOWING: a) DAMAGES BASED ON ANY THIRD PARTY CLAIM; b) LOSS OF,
OR DAMAGE TO, CUSTOMER’S RECORDS, FILES OR DATA; OR c) DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS),
WHETHER IN CONTRACT, TORT OR OTHERWISE (INCLUDING NEGLIGENCE) ARISING OUT OF YOUR
USE OF THE SOFTWARE, EVEN IF NORTEL NETWORKS, ITS AGENTS OR SUPPLIERS HAVE BEEN
ADVISED OF THEIR POSSIBILITY. The forgoing limitations of remedies also apply to any developer and/or supplier
of the Software. Such developer and/or supplier is an intended beneficiary of this Section. Some jurisdictions do not
allow these limitations or exclusions and, in such event, they may not apply.
NN46110-308 02.01
5
4.
General
a.
If Customer is the United States Government, the following paragraph shall apply: All Nortel Networks
Software available under this License Agreement is commercial computer software and commercial computer
software documentation and, in the event Software is licensed for or on behalf of the United States
Government, the respective rights to the software and software documentation are governed by Nortel
Networks standard commercial license in accordance with U.S. Federal Regulations at 48 C.F.R. Sections
12.212 (for non-DoD entities) and 48 C.F.R. 227.7202 (for DoD entities).
b.
Customer may terminate the license at any time. Nortel Networks may terminate the license if Customer fails
to comply with the terms and conditions of this license. In either event, upon termination, Customer must
either return the Software to Nortel Networks or certify its destruction.
c.
Customer is responsible for payment of any taxes, including personal property taxes, resulting from
Customer’s use of the Software. Customer agrees to comply with all applicable laws including all applicable
export and import laws and regulations.
d.
Neither party may bring an action, regardless of form, more than two years after the cause of the action arose.
e.
The terms and conditions of this License Agreement form the complete and exclusive agreement between
Customer and Nortel Networks.
f.
This License Agreement is governed by the laws of the country in which Customer acquires the Software. If
the Software is acquired in the United States, then this License Agreement is governed by the laws of the state
of New York.
Nortel VPN Router Installation — VPN Router 600
6
NN46110-308 02.01
7
Contents
New in this release. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1000BASE-T (1000 GT) Ethernet card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
How to get help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Finding the latest updates on the Nortel Web site . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Getting help from the Nortel Web site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Getting help over the phone from a Nortel Solutions Center . . . . . . . . . . . . . . . . . . . . 18
Getting help from a specialist by using an Express Routing Code . . . . . . . . . . . . . . . 18
Getting help through a Nortel distributor or reseller . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Text conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Printed technical manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Chapter 1
Introducing the Nortel VPN Router 600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Description of the Nortel VPN Router 600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Preparing to install the Nortel VPN Router 600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Shipment contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Site requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Installing the chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Nortel VPN Router Installation — VPN Router 600
8
Chapter 2
Cabling the VPN Router and turning the power on . . . . . . . . . . . . . . . . . . 29
Connecting communications cables VPN Router 600 . . . . . . . . . . . . . . . . . . . . . . . . . 30
Connecting the power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Understanding the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Front panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
LEDs on the system 10/100BASE-TX Ethernet ports . . . . . . . . . . . . . . . . . . . . . . 35
10/100BASE-TX Ethernet interface card LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
1000BASE-T (1000 GT) Ethernet interface card LEDs . . . . . . . . . . . . . . . . . . . . . 37
56/64K CSU/DSU WAN interface card LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
ADSL WAN interface card LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
T1/E1 CSU/DSU WAN interface card LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Single V.35/X.21 WAN interface card LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Chapter 3
Configuring the management IP interface. . . . . . . . . . . . . . . . . . . . . . . . . . 43
Required information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Configuring the management IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Testing the configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Chapter 4
Installing option cards and DIMMs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Shutting down the system to add or replace hardware . . . . . . . . . . . . . . . . . . . . . . . . 52
Opening the Nortel VPN Router 600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Installing and replacing an option card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Replacing a DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Chapter 5
Using recovery mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Nortel VPN Router Installation — VPN Router 600
Contents 9
Appendix A
Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Chassis specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
System ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
10/100BASE-TX Ethernet LAN port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Serial port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Modem cable specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Hardware option cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
10/100BASE-TX Ethernet interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
1000BASE-T (1000 GT) Ethernet interface card . . . . . . . . . . . . . . . . . . . . . . . . . . 77
56/64K CSU/DSU WAN interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
ADSL WAN interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
ISDN BRI interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
T1/E1 CSU/DSU WAN interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Single V.35/X.21 WAN interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
V.90 modem interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Nortel VPN Router Installation — VPN Router 600
10
Contents
NN46110-308 02.01
11
Figures
Figure 1
Front view of the VPN Router 600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 2
Rear view of the VPN Router 600 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 3
Front panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 4
LEDs on the system 10/100BASE-TX Ethernet port . . . . . . . . . . . . . . . . 35
Figure 5
LEDs on the 10/100BASE-TX Ethernet interface card . . . . . . . . . . . . . . . 36
Figure 6
LEDs on the 1000BASE-T (100 GT) Ethernet interface card . . . . . . . . . . 37
Figure 7
LEDs on the 56/64K CSU/DSU WAN interface card . . . . . . . . . . . . . . . . 38
Figure 8
LEDs on the ADSL WAN interface card . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 9
LEDs on the T1/E1 CSU/DSU WAN interface card . . . . . . . . . . . . . . . . . 40
Figure 10
LEDs on the single V.35/X.21 WAN interface card . . . . . . . . . . . . . . . . . . 41
Figure 11
Removing the screws from the bottom of the VPN Router 600 . . . . . . . . 53
Figure 12
Removing the chassis from the steel enclosure . . . . . . . . . . . . . . . . . . . . 54
Figure 13
VPN Router 600 system board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 14
Removing the blank bracket from the option card slot . . . . . . . . . . . . . . . 58
Figure 15
Inserting the option card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 16
Securing the option card in the slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 17
Replacing the chassis in the steel enclosure . . . . . . . . . . . . . . . . . . . . . . 60
Figure 18
Installing a DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 19
Recovery Diskette screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 20
10/100BASE-TX Ethernet connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 21
Serial cable (9-pin D-sub plug to RS-232-C modem plug) . . . . . . . . . . . . 74
Figure 22
Modem cable (9-pin D-sub plug to RS-232-C modem plug) . . . . . . . . . . . 75
Figure 23
10/100BASE-TX Ethernet interface card . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 24
1000BASE-T (1000 GT) Ethernet interface card . . . . . . . . . . . . . . . . . . . 78
Figure 25
56/64K CSU/DSU WAN interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 26
ADSL WAN interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Figure 27
ISDN BRI S/T interface card and ISDN BRI U interface card . . . . . . . . . . 82
Figure 28
T1/E1 CSU/DSU WAN interface card (half-height card) . . . . . . . . . . . . . . 83
Figure 29
T1/E1 CSU/DSU WAN interface card (full-height card) . . . . . . . . . . . . . . 84
Nortel VPN Router Installation — VPN Router 600
12
Figures
Figure 30
Single V.35/X.21 WAN interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Figure 31
V.90 modem interface card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
NN46110-308 02.01
13
Tables
Table 1
Items shipped with the Nortel VPN Router 600 . . . . . . . . . . . . . . . . . . . . 27
Table 2
Interfaces and cables for the VPN Router 600 . . . . . . . . . . . . . . . . . . . . . 30
Table 3
Power cord requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Table 4
Front panel LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 5
LED indicators on the system 10/100BASE-TX Ethernet port . . . . . . . . . 35
Table 6
LED indicators on the 10/100BASE-TX Ethernet interface card . . . . . . . . 36
Table 7
LED indicators on the 1000BASE-T (100 GT) Ethernet interface card . . . 37
Table 8
LED indicators on the 56/64K CSU/DSU WAN interface card . . . . . . . . . 38
Table 9
LED indicators on the ADSL WAN interface card . . . . . . . . . . . . . . . . . . . 39
Table 10
LED indicators on the T1/E1 CSU/DSU WAN interface card . . . . . . . . . . 40
Table 11
LED indicators on the single V.35/X.21 WAN interface card . . . . . . . . . . 41
Table 12
Supported option cards for the Nortel VPN Router 600 600 . . . . . . . . . . . 56
Table 13
Physical, electrical, and environmental specifications . . . . . . . . . . . . . . . 71
Table 14
10/100BASE-TX Ethernet port pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table 15
Multiple DB9 and DB25 connector pinouts . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 16
Modem cable pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Table 17
1000BASE-T (1000 GT) Ethernet pinouts . . . . . . . . . . . . . . . . . . . . . . . . 78
Table 18
56/64K CSU/DSU cable pinouts for crossover connection . . . . . . . . . . . . 79
Table 19
56/64K CSU/DSU cable pinouts for straight-through connection . . . . . . . 80
Table 20
ADSL cable pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Table 21
ISDN BRI S/T cable pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 22
ISDN BRI U cable pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 23
T1/E1 CSU/DSU cable pinouts for crossover connection . . . . . . . . . . . . . 84
Table 24
T1/E1 CSU/DSU cable pinouts for straight-through connection . . . . . . . . 85
Table 25
V.35 cable pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Table 26
X.21 cable pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Table 27
V.90 modem cable pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Nortel VPN Router Installation — VPN Router 600
14
Tables
NN46110-308 02.01
15
New in this release
The following section details what’s new in Nortel VPN Router Installation—
VPN Router 600 (NN46110-308) for Release 7.05.300:
Features
See the following section for information about feature changes:
1000BASE-T (1000 GT) Ethernet card
The 100 GT Ethernet card replaces the 10/ 100BASE-TX Ethernet card. See
“1000BASE-T (1000 GT) Ethernet interface card LEDs” on page 37 and
“1000BASE-T (1000 GT) Ethernet interface card” on page 77.
Nortel VPN Router Installation — VPN Router 600
16
New in this release
NN46110-308 02.01
17
How to get help
This chapter explains how to get help for Nortel products and services.
Finding the latest updates on the Nortel Web site
The content of this documentation was current at the time the product was
released. To check for updates to the latest documentation and software for the
VPN Router 600, go to:
www.nortel.com/support
Select Security & VPN and then, in the section called Virtual Private Networking
(VPN), IPSEC, and SSL, click the appropriate VPN Router product.
Getting help from the Nortel Web site
The best way to get technical support for Nortel products is from the Nortel
Technical Support Web site:
www.nortel.com/support
Nortel VPN Router Installation — VPN Router 600
18
How to get help
This site provides quick access to software, documentation, bulletins, and tools to
address issues with Nortel products. From this site you can:
•
•
•
•
download software, documentation, and product bulletins
search the Technical Support site and the Nortel Knowledge Base for answers
to technical issues
sign up for automatic notification of new software and documentation for
Nortel equipment
open and manage technical support cases
Getting help over the phone from a Nortel Solutions
Center
If you do not find the information you require on the Nortel Technical Support
Web site, and you have a Nortel support contract, you can also get help over the
phone from a Nortel Solutions Center.
In North America, call 1-800-4NORTEL (1-800-466-7835).
Outside North America, go to the following Web site to obtain the phone number
for your region:
www.nortel.com/callus
Getting help from a specialist by using an Express
Routing Code
To access some Nortel Technical Solutions Centers, you can use an Express
Routing Code (ERC) to quickly route your call to a specialist in your Nortel
product or service. To locate the ERC for your product or service, go to:
www.nortel.com/erc
NN46110-308 02.01
How to get help 19
Getting help through a Nortel distributor or reseller
If you purchased a service contract for your Nortel product from a distributor or
authorized reseller, contact the technical support staff for that distributor or
reseller.
Nortel VPN Router Installation — VPN Router 600
20
How to get help
NN46110-308 02.01
21
Preface
The VPN Router 600 is part of the Nortel VPN Router product family. Nortel
VPN Routers support secure, reliable IP VPNs in a single, integrated hardware
device. Throughout this guide, the VPN Router 600 is also referred to as the
gateway.
This guide provides instructions on how to install and start the VPN Router 600
and how to install and replace option cards and the dual inline memory module
(DIMM). This guide also provides some initial configuration information and
includes technical specifications for the gateway.
For complete information about configuring and monitoring the VPN Router 600,
see the documentation on the software CD. (For information about VPN Router
documentation, see “Related publications” on page 23.)
Before you begin
This guide is intended for qualified service personnel who are installing the VPN
Router 600 for the first time or who need to install or replace the following field
replaceable units (FRU):
•
•
LAN, WAN, and serial option cards
Dual inline memory module (DIMM)
Before you install the VPN Router 600, use standard cable system practices to
install all the network wiring on the premises.
Nortel VPN Router Installation — VPN Router 600
22
Preface
Text conventions
This guide uses the following text conventions:
bold Courier text
Indicates command names and options and text that
you need to enter.
Example: Use the show health command.
Example: Enter terminal paging {off | on}.
italic text
Indicates new terms and book titles.
plain Courier
text
Indicates system output, for example, prompts and
system messages.
Example: File not found.
separator ( > )
Shows menu paths.
Example: Choose Status > Health Check.
Acronyms
This guide uses the following acronyms:
ADSL
asymmetric digital subscriber line
AIS
alarm indication signal
BRI
Basic Rate Interface
CSU
channel service unit
DIMM
dual inline memory module
DSU
digital service unit
DTE
data terminal equipment
IP
Internet Protocol
IPsec
IP Security
ISDN
Integrated Services Digital Network
LAN
local area network
LED
light emitting diode
NN46110-308 02.01
Preface
LOS
loss of signal
OOF
out of frame
PCI
peripheral component interconnect
URL
uniform resource locator
VPN
virtual private network
WAN
wide area network
23
Related publications
For complete information about configuring, monitoring, and managing the VPN
Router 600, formerly known as the Contivity Secure IP Services Gateway 600,
refer to the following publications:
•
•
•
•
•
•
•
Release notes provide the latest information, including brief descriptions of
the new features, problems fixed in this release, and known problems and
workarounds.
Nortel VPN Router Configuration — Basic Features (NN46110-500)
introduces the product and provides information about initial configuration.
Nortel VPN Router Security — Servers, Authentication, and Certificates
(NN46110-600) provides instructions for configuring authentication servers
and services, as well as digital certificates.
Nortel VPN Router Security — Firewalls, Filters, NAT, and QoS
(NN46110-601) provides instructions for configuring the VPN Router
Stateful Firewall, NAT, and VPN Router interface and tunnel filters.
Nortel VPN Router Configuration — Tunneling Protocols) (NN46110-503)
provides instructions for configuring the tunneling protocols IPsec, L2TP,
PPTP, and L2F.
Nortel VPN Router Configuration — Advanced Features (NN46110-502)
provides instructions for configuring 802.1Q VLANs, circuitless IP, advanced
WAN settings, PPP, PPPoE, frame relay, ADSL and ATM, T1/E1 CSU/DSU
interfaces, dial services and BIS, DLSw, IPX, and Hardware Accelerator
cards.
Nortel VPN Router Configuration — Routing (NN46110-504) provides
instructions for configuring RIP, OSPF, and VRRP, as well as instructions for
configuring ECMP, routing policy services, and client address redistribution.
Nortel VPN Router Installation — VPN Router 600
24
Preface
•
•
•
•
Nortel VPN Router Configuration — SSL VPN Services (NN46110-501)
provides instructions for configuring services on the SSL VPN Module 1000,
including authentication, networks, user groups, and portal links.
Nortel VPN Router Using the Command Line Interface (NN46110-507)
provides syntax, descriptions, and examples for the commands that you can
use to configure, manage, and monitor the gateway.
Nortel VPN Router Troubleshooting (NN46110-602) provides information
about backup and recovery, file management, upgrading software, and
troubleshooting. This guide also provides instructions for monitoring gateway
status and performance.
Nortel VPN Router Configuration — Tunnel Guard (NN46110-307) provides
information about configuring and using the TunnelGuard feature.
Printed technical manuals
You can print selected technical manuals and release notes free, directly from the
Internet. Go to www.nortel.com/documentation, find the product for which you
need documentation, then locate the specific category and model or version for
your hardware or software product. Use Adobe Reader to open the manuals and
release notes, search for the sections you need, and print them on most standard
printers. Go to Adobe Systems at www.adobe.com to download a free copy of the
Adobe Reader.
NN46110-308 02.01
25
Chapter 1
Introducing the Nortel VPN Router 600
This chapter describes the VPN Router 600 and how to install it.
Note: Before you install the chassis, use standard cable system practices
to install all network wiring on the premises.
This chapter contains the following topics:
Topic
Page
Description of the Nortel VPN Router 600
25
Preparing to install the Nortel VPN Router 600
26
Installing the chassis
28
Description of the Nortel VPN Router 600
The VPN Router 600 enables scalable, secure, and robust IP virtual private
networks (VPNs) for up to 50 simultaneous users across the public data network.
The VPN Router 600 is for branch offices and small businesses that need to be
interconnected through managed Internet Protocol (IP) VPNs.
The VPN Router 600 provides routing, firewall, bandwidth management,
encryption, authentication, and data integrity services to ensure secure tunneling
across IP networks and the Internet. An individual user or group of users can be
associated with a set of attributes that provide custom access to an extranet.
Nortel VPN Router Installation — VPN Router 600
26 Chapter 1 Introducing the Nortel VPN Router 600
Figure 1 shows the front view of the VPN Router 600.
Figure 1 Front view of the VPN Router 600
N
VP
n
00
r6
te
ou
R
t
er
w
Po
er
io
nt
te
Al
At
dy
ea
R
ot
Bo
CS60001A
The VPN Router 600 chassis provides the following:
•
•
•
•
Two 10/100 Ethernet LAN ports on the base system
One serial port for out-of-band management of the VPN Router 600
One expansion PCI slot that can contain an optional interface card
One 128 MB dual inline memory module (DIMM)
Preparing to install the Nortel VPN Router 600
Before you install the VPN Router 600, verify that:
•
•
•
Your shipment is complete and undamaged.
You have the cables that you need.
Your installation site meets the physical, electrical, and environmental
requirements.
The sections that follow provide information to help you prepare for installation.
NN46110-308 02.01
Chapter 1 Introducing the Nortel VPN Router 600 27
Shipment contents
In addition to the gateway and this guide, the shipping container for the VPN
Router 600 contains a number of hardware accessories and other items.
Note: Nortel does not ship a power cord with the VPN Router 600
unless you order one.
Table 1 lists the hardware accessories and other items shipped with the gateway.
Table 1 Items shipped with the Nortel VPN Router 600
Quantity
Item
Description
1
Molded serial cable
DB9/DB25-to-DB9/DB25
Used to connect the VPN Router 600 to a PC or
to a local terminal
1
AC-to-DC external power
supply pack
Provides power to the VPN Router 600
1
Important Notice for the
VPN Router 600
Provides shorter instructions for installing the
chassis
1
VPN Router software kit
Contains VPN Router software and
documentation (including this book) on CD
1
VPN client kit
Contains VPN Client software and
documentation on CD
Inspect all items for shipping damage. If you detect any damage, do not install the
VPN Router 600. Call the Nortel Technical Solutions Center in your area (see
“How to get help” on page 17).
Cables
You need cables that are not included in the VPN Router 600 shipping container.
For information about which cables are shipped and which ones you can order,
see “Connecting communications cables VPN Router 600” on page 30. If you do
not have the proper cables, contact your network administrator.
Nortel VPN Router Installation — VPN Router 600
28 Chapter 1 Introducing the Nortel VPN Router 600
Site requirements
The installation site must provide sufficient free space around the VPN Router
600 to ensure proper ventilation and access for servicing. For information about
the physical, electrical, and environmental requirements for the VPN Router 600,
see “Chassis specifications” on page 71.
Installing the chassis
To install the VPN Router 600, position the chassis on a flat, sturdy, horizontal
surface. Make sure that the surface is large enough for the gateway and sturdy
enough to support the combined weight of the VPN Router 600 and the cables that
you attach to it.
NN46110-308 02.01
29
Chapter 2
Cabling the VPN Router and turning the power on
This chapter provides information about how to connect communications cables
and the power cord to the VPN Router 600.
Caution: Connect the cables to the built-in Ethernet ports and to the
interfaces on the optional interface card installed in the VPN Router 600
before you plug the power cord into the outlet.
This chapter contains the following topics:
Topic
Page
Connecting communications cables VPN Router 600
30
Connecting the power cord
32
Understanding the LEDs
33
Caution: Route the cable for all WAN, LAN, and serial connections
inside the building environment.
Nortel VPN Router Installation — VPN Router 600
30 Chapter 2 Cabling the VPN Router and turning the power on
Connecting communications cables VPN Router 600
Gather the cables that you must attach to the VPN Router 600.
Table 2 lists the system ports and the ports provided on the optional interface
cards that you can install in the VPN Router 600. The table also indicates whether
you can obtain cables for the ports from Nortel.
Table 2 Interfaces and cables for the VPN Router 600
Cable available from Nortel
Interface
Included
Ordered separately
10/100BASE-TX Ethernet system port
Serial port
Contact supplier
X
X
10/100BASE-TX Ethernet
X
1000BASE-T (1000 GT) Ethernet
X
56/64K CSU/DSU WAN
X
ADSL WAN
X
ISDN BRI
X
V.90 modem
X
T1/E1 CSU/DSU WAN
Single V.35/X.21 WAN
X
X1
1 Order either the V.35 cable or the X.21 cable.
For information about the connectors and cable pinouts, see Appendix A,
“Technical specifications,” on page 71.
Figure 2 on page 31 shows the back of the VPN Router 600. All interface cables
and the power cord attach to the rear of the gateway.
NN46110-308 02.01
Chapter 2 Cabling the VPN Router and turning the power on 31
Figure 2 Rear view of the VPN Router 600
I/O EXPANSION BAY
CONSOLE
LAN 1
FD
LAN 0
RC
DC INPUT
+12V-1.7A
-12V-0.1A
+5V-10A
75W MAX
CS60002A
Connect the interface cables to the VPN Router 600 in this order:
1
Connect the 10/100BASE-TX RJ-45 cables to the built-in 10/100BASE-TX
Ethernet LAN ports on the gateway (Figure 2).
2
Connect the serial cable shipped with the VPN Router 600 to the serial port
(Figure 2), if you plan to connect a terminal or PC to the gateway.
3
Connect the appropriate cables to the ports on the installed interface card.
If you ordered optional interface cards, connect the cables for these interfaces
to the ports.
Nortel VPN Router Installation — VPN Router 600
32 Chapter 2 Cabling the VPN Router and turning the power on
Connecting the power cord
You must order the power cord for the VPN Router 600 separately.
Caution: Risk of equipment damage
Do not modify or use the AC power cord if it is not the exact type that is
required for your power outlet.
The power cord must meet the requirements described in Table 3.
Table 3 Power cord requirements
Requirement
Description
Current rating
The power cord must be rated for the available AC voltage and
must have a current rating that is at least 125 percent of the
gateway’s current rating (100—240 VAC).
Certification
The power cord must have certification marks from an
acceptable regional agency.
Cord length and flexibility The power cord must be less than 4.5 meters (14.7 feet) long.
It must be a flexible HAR (harmonized) cord or VDE-certified
cordage to comply with the gateway’s safety certifications.
Power supply connector
The connector that you plug into the AC receptacle on the
VPN Router 600 power supply must be an IEC 320, Sheet
C13 female.
Wall outlet connector
The power cord must terminate in a male plug with
appropriate grounding.
To connect the power cord and turn on the system power:
Caution: Before you connect the power supply to the gateway, connect
the cables to the Ethernet and serial ports and to the ports on the installed
option card.
1
Plug the cable attached to the external power pack into the receptacle labeled
“DC Input” on the rear of the VPN Router 600 (Figure 2 on page 31).
Locate the word “top” on the plug end of the cable and align that part of the
cable with the arrow printed above the DC input port.
NN46110-308 02.01
Chapter 2 Cabling the VPN Router and turning the power on 33
2
Plug the female end of the power cord into the external power supply pack.
3
Plug the male end of the power cord into a surge protector.
Caution: Risk of equipment damage
Protect the VPN Router 600 by plugging it into a surge suppressor.
4
Plug the surge protector (or the power cord) into the power outlet.
The VPN Router 600 should begin to boot.
Note: The VPN Router 600 has no power switch. Connecting the VPN
Router 600 to a power supply turns the gateway on.
5
Verify a successful installation by checking the LEDs on the front panel (see
“Front panel LEDs” on page 34).
If the Ready LED does not turn green (to indicate that the gateway has booted
successfully), check that you properly attached the power cord to the power
supply pack and to the power outlet.
If the VPN Router 600 still does not boot, contact your local Nortel Technical
Solutions Center (see “How to get help” on page 17).
Understanding the LEDs
This section describes the LEDs on the front panel of the VPN Router 600 and on
the interface cards that have LEDs. You can confirm that the LAN and WAN
interfaces are cabled properly by examining the LEDs.
Nortel VPN Router Installation — VPN Router 600
34 Chapter 2 Cabling the VPN Router and turning the power on
Front panel LEDs
The front panel of the VPN Router 600 has five LEDs (Figure 3). These LEDs
indicate the status of the VPN Router 600.
Figure 3 Front panel LEDs
N
VP
r
te
ou
R
0
60
er
w
Po
t
er
Al
n
io
nt
te
At
dy
ot
ea
R
Bo
CS60001A
Table 4 describes the LEDs on the VPN Router 600 front panel.
Table 4 Front panel LED indicators
LED
Indicator
Description
Power
On
The gateway is receiving DC power.
Off
The gateway is not receiving DC power.
Alert
Red
A serious alarm condition exists that requires attention.
A red alert usually indicates a hardware error. The red
alert condition is described in the health check display.
Attention
Amber
A non-fatal alarm condition exists. The yellow alert
condition is described in the health check display.
Ready
Green
The gateway has booted and is operational.
Boot
Amber
The gateway is booting and is in a non-ready state.
If the Boot LED and the Ready LED light at the same
time, the VPN Router 600 is in recovery mode (see
Chapter 5, “Using recovery mode,” on page 65).
For complete information about the health check, event log, and system log, see
Nortel VPN Router Troubleshooting (NN46110-602).
NN46110-308 02.01
Chapter 2 Cabling the VPN Router and turning the power on 35
LEDs on the system 10/100BASE-TX Ethernet ports
Figure 4 shows the LEDs for the 10/100BASE-TX Ethernet ports located on the
rear of the VPN Router 600.
Figure 4 LEDs on the system 10/100BASE-TX Ethernet port
Yellow
Green
CS260011A
Table 5 describes the LEDs on the system 10/100BASE-TX Ethernet ports.
Table 5 LED indicators on the system 10/100BASE-TX Ethernet port
LED
Indicator
Description
Green
On
The LAN port is operating at 100 Mb/s.
Off
The LAN port is operating at 10 Mb/s.
On
The cable connections between the LAN port and the
hub are good.
Off
The cable connections between the LAN port and the
hub are faulty.
Flashing
The LAN port is sending or receiving network data.
The frequency of the flashes increases with
increased traffic.
Yellow
Nortel VPN Router Installation — VPN Router 600
36 Chapter 2 Cabling the VPN Router and turning the power on
10/100BASE-TX Ethernet interface card LEDs
Figure 5 shows the LEDs on the 10/100BASE-TX Ethernet interface card.
100TX
DATA
ACT/LINK
Figure 5 LEDs on the 10/100BASE-TX Ethernet interface card
Activity/Link
10/100 Mb/s
CS260009A
The following describes the LEDs on the 10/100BASE-TX Ethernet interface
card.
Table 6 LED indicators on the 10/100BASE-TX Ethernet interface card
LED
Indicator
Description
ACT/LINK
Steady Green or
Flashing Green
The card is sending or receiving network data. The
frequency of the flashes increases with increased
traffic.
Off
The card is not sending or receiving data.
Green
The port is operating at 100 Mb/s.
Off
The port is operating at 10 Mb/s.
10/100TX
NN46110-308 02.01
Chapter 2 Cabling the VPN Router and turning the power on 37
1000BASE-T (1000 GT) Ethernet interface card LEDs
The following figure shows the LEDs on the 10BASE-T/100BASE-TX/
1000BASE-T Ethernet interface card.
Note: The 1000BASE-T (100 GT) Ethernet interface card can only
operate at 10/100 Mbit/s on the VPN Router 600.
Figure 6 LEDs on the 1000BASE-T (100 GT) Ethernet interface card
The following table describes the LEDs on the1000BASE-T (100 GT) Ethernet
interface card.
Table 7 LED indicators on the 1000BASE-T (100 GT) Ethernet interface card
LED
Indicator
Description
ACT/LINK
Steady green
The port is connected to a valid link partner.
Flashing green
The card is sending or receiving network data. The
frequency of the flashes increases with increased
traffic.
Off
The card is not sending or receiving data.
Green
The port is operating at 100 Mb/s.
Off
The port is operating at 10 Mb/s.
10/100/1000
Nortel VPN Router Installation — VPN Router 600
38 Chapter 2 Cabling the VPN Router and turning the power on
56/64K CSU/DSU WAN interface card LEDs
Figure 7 shows the LEDs on the 56/64K CSU/DSU WAN interface card.
Figure 7 LEDs on the 56/64K CSU/DSU WAN interface card
Blue LED
Red LED
56/64K
DDS
Green LED
Yellow LED
Table 8 describes the LEDs on the 56/64K CSU/DSU WAN interface card.
Table 8 LED indicators on the 56/64K CSU/DSU WAN interface card
LED
Description
Blue
The blue alarm LED is lit when receiving an upstream failure
denoted by an alarm indication signal (AIS).
Red
The red alarm LED is lit when a loss-of-signal (LOS) or
out-of-frame (OOF) condition is detected on the receive signal.
Yellow
The yellow alarm LED is lit when the far-end equipment is in the
red alarm condition.
Green
The green LED is lit when the condition is normal operation.
NN46110-308 02.01
Chapter 2 Cabling the VPN Router and turning the power on 39
ADSL WAN interface card LEDs
Figure 8 shows the LEDs on the ADSL WAN interface card.
Figure 8 LEDs on the ADSL WAN interface card
RX/TX LED
RX/TX
ADSL
CONN
CONN LED
Table 9 describes the LEDs on the ADSL WAN interface card.
Table 9 LED indicators on the ADSL WAN interface card
CONN LED
Tx/Rx LED
Description
Steady green
Steady green
The ADSL interface card is not initialized; the
software driver is not installed.
Off
Off
The ADSL interface card is initialized, but has not
established a link with the ADSL network.
Flashing green
Off
The ADSL interface card is attempting to establish a
link with the ADSL network.
Steady green
Off
The ADSL interface card has established a link with
the ADSL network.
Steady green
Flashing green
The ADSL interface card is sending or receiving
network data. (The LED can be dim.)
Nortel VPN Router Installation — VPN Router 600
40 Chapter 2 Cabling the VPN Router and turning the power on
T1/E1 CSU/DSU WAN interface card LEDs
Figure 9 shows the LEDs on the T1/E1 CSU/DSU WAN interface card.
Figure 9 LEDs on the T1/E1 CSU/DSU WAN interface card
LED 1, Red
LED 2, Blue
LED 4, Green
LED 3, Yellow
CS160012A
Table 10 describes the LEDs on the T1/E1 CSU/DSU WAN interface card.
Table 10 LED indicators on the T1/E1 CSU/DSU WAN interface card
LED
Indicator
Description
LED 1
Red
The red alarm LED is lit when a loss-of-signal (LOS) or
out-of-frame (OOF) condition is detected on the receive
signal.
LED 2
Blue
The blue alarm LED is lit when receiving an upstream
failure denoted by an alarm indication signal (AIS).
LED 3
Yellow
The yellow alarm LED is lit when the far-end equipment
is in the red alarm condition.
LED 4
Green
The green LED is lit when the condition is normal
operation.
NN46110-308 02.01
Chapter 2 Cabling the VPN Router and turning the power on 41
Single V.35/X.21 WAN interface card LEDs
Figure 10 shows the LEDs on the single V.35/X.21 WAN interface card.
Figure 10 LEDs on the single V.35/X.21 WAN interface card
LED 1, Red
LED 2, Green
LED 4, Green
LED 3, Green
Table 11 describes the LEDs on the single V.35/X.21 WAN interface card.
Table 11 LED indicators on the single V.35/X.21 WAN interface card
LED
Indicator
Description
LED 1
Red
No external transmit clock source is available.
LED 2
Green
The signals CDC and DSR are on between the DSU
and the adapter. LED 2 detects receive link status.
LED 3
Green
Power to the adapter is on and the onboard
microcode is loaded.
LED 4
Green
Cable is detected.
Nortel VPN Router Installation — VPN Router 600
42 Chapter 2 Cabling the VPN Router and turning the power on
NN46110-308 02.01
43
Chapter 3
Configuring the management IP interface
This chapter describes how to configure a management IP address, subnet mask,
and default gateway address on a newly installed VPN Router 600. After you
complete the procedures in this chapter, you can configure and manage the VPN
Router 600 using a Web browser from a PC.
To configure the management IP address, you use the serial interface
configuration menu. You must connect a PC or terminal to the serial port on the
VPN Router 600.
This chapter contains the following topics:
Topic
Page
Required information
44
Configuring the management IP address
48
Testing the configuration
49
Troubleshooting
50
Nortel VPN Router Installation — VPN Router 600
44 Chapter 3 Configuring the management IP interface
Required information
Before you configure the management interface, collect this information:
•
IP address for the management interface
The management IP address must be accessible from one of the private
physical interfaces on the VPN Router 600. For example, if you plan to assign
IP address 10.2.3.3 with subnet mask 255.255.0.0 to the private physical
interface, the management IP address must reside in the 10.2 network.
•
Subnet mask
The subnet mask specifies which IP addresses are directly reachable on the
network and which ones must be routed through a gateway. For example, the
IP address 10.2.3.3 with a subnet mask of 255.255.0.0 indicates that all hosts
with addresses 10.2.n.n are directly reachable.
•
Default gateway (optional)
The default gateway routes packets to destinations for which there is no
specific route in the routing table. You can configure a default gateway when
you assign the management IP address, or you can configure it at a later time.
Note: Write down and save the management IP address. You need it to
configure the VPN Router 600.
NN46110-308 02.01
Chapter 3 Configuring the management IP interface 45
Configuring the management IP address
You use the serial interface to assign the VPN Router 600 a management IP
address and subnet mask so that you can then use a Web browser for management.
To configure the management IP address using the serial interface:
1
Turn on the terminal or PC.
The terminal or PC should be configured as follows:
•
•
•
•
•
9600 baud
8 data bits
1 stop bit
No parity
No flow control
2
Connect the serial cable (supplied with the VPN Router 600) from the
gateway’s serial port to a terminal or to the communications port on a PC.
3
On the PC, start HyperTerminal or another terminal emulation program, and
press Enter.
The Nortel VPN Router screen appears.
Nortel VPN Router
Copyright (c) 1999-2005 Nortel Networks, Inc.
Version:
Creation date:
Unit Serial Number:
V07_0.024
Jul 6 2006, 08:23:16
510649
Please enter the administrator's user name:
4
Enter the default user name and password for the administrator.
The factory default user name is admin and the default password is setup. The
user name and password are case sensitive.
Please enter the administrator's user name: admin
Please enter the administrator's password: *****
Nortel VPN Router Installation — VPN Router 600
46 Chapter 3 Configuring the management IP interface
The serial main menu appears.
Main Menu: System is currently in NORMAL mode.
0)
1)
2)
3)
4)
5)
6)
7)
8)
9)
B)
P)
C)
L)
R)
E)
Management Address
Interfaces
Administrator
Default Private Route Menu
Default Public Route Menu
Create A User Control Tunnel (IPsec) Profile
Restricted Management Mode
FALSE
Allow HTTP Management
TRUE
Firewall Options
Shutdown
System Boot Options
Configure Serial Port
Controlled Crash
Command Line Interface
Reset System to Factory Defaults
Exit, Save and Invoke Changes
Please select a menu choice (0 - 9,B,P,C,L,R,E):
5
To configure the Interface IP address from the serial menu, type 1, and press
Enter.
The interface menu appears.
- Interface Menu
0) Slot 0, Port 2, Public LAN
IP Address =
Subnet Mask = 0.0.0.0
Speed/Duplex = AutoNegotiate
1) Slot 0, Port 1, Private LAN
IP Address =192.167.120.14
Subnet Mask = 255.255.255.0
Speed/Duplex = AutoNegotiate
R) Return to the Main Menu.
Please select a menu choice:
NN46110-308 02.01
Chapter 3 Configuring the management IP interface 47
6
Type 0, and press Enter to configure the IP address.
The IP address prompt appears.
0) Slot 0, Port 2, Public LAN
IP Address =
Subnet Mask = 0.0.0.0
Speed/Duplex = AutoNegotiate
*Type 0.0.0.0 to delete.
*Just type <CR> to skip.
Old IP address =
New IP address =
7
Type a new IP address, and press Enter.
The subnet mask prompt appears.
Old Subnet Mask = 0.0.0.0
New Subnet Mask =
8
At the New Subnet Mask prompt, type the subnet mask for the management
IP address, and press Enter.
The Speed/Duplex prompt appears.
9
Press Enter to leave the speed and duplex settings unchanged.
The Interface menu appears again with the changes you made.
0) Slot 0, Port 2, Public LAN
IP Address =
Subnet Mask = 0.0.0.0
Speed/Duplex = AutoNegotiate
1) Slot 0, Port 1, Private LAN
IP Address =192.167.120.14
Subnet Mask = 255.255.255.0
Speed/Duplex = AutoNegotiate
R) Return to the Main Menu.
Please select a menu choice:
Nortel VPN Router Installation — VPN Router 600
48 Chapter 3 Configuring the management IP interface
Type R, and press Enter to return to the serial main menu.
10 To configure the management IP address, type 0 and press Enter.
The Management IP Address menu appears.
- Management IP Address Menu
M) Management IP Address =
R) Return to the Main Menu
Please select a menu choice (M,R):
11 Type M, and press Enter.
The Management IP Address prompt appears.
*Type 0.0.0.0 to delete.
*Just type <CR> to skip.
Old management IP address =
New management IP address =
12 Type the new management IP address, and press Enter to configure the
management IP address.
The new IP management address appears in the Management IP Address
menu.
- Management IP address menu
M) Management IP Address =192.167.120.13
R) Return to the Main Menu
Please select a menu choice (M,R):
13 Type R, and press Enter to return to the serial main menu.
The serial main menu appears.
14 From the serial main menu, type E, and press Enter to save the new
management IP address and mask, and to exit the serial menu.
15 Go to the next section, “Testing the configuration” on page 49, to verify that
you can access the VPN Router 600 from a Web browser.
NN46110-308 02.01
Chapter 3 Configuring the management IP interface 49
For detailed information about configuring and managing the VPN Router 600,
refer to the documentation on the VPN Router software CD.
Testing the configuration
After you assign a management IP address to the VPN Router 600, start your Web
browser to verify that you can access the gateway from the browser.
To manage the VPN Router 600 using the graphic user interface (GUI), your PC
must be running one of the following browsers:
•
•
•
Windows 2000 and NT
— Internet Explorer 6.0 or later
— Mozilla 1.7 or later
— Firefox (all versions)
— Netscape 7.x, 8.0.x or 8.1.x
Unix
— Firefox 1.5 or later
— Mozilla 1.7 or later
Linux
— Firefox 1.5 or later
— Mozilla 1.7 or later
To test the management IP address on the VPN Router 600:
1
Open a Web browser.
2
In the URL field, enter http:// followed by the management IP address that
you assigned to the VPN Router 600.
For example, if the management IP address is 10.2.3.2, enter http://10.2.3.2.
If the Welcome screen appears, you correctly configured the management IP
address for the VPN Router 600.
Note: If the Welcome screen does not appear, see “Troubleshooting” on
page 50.
Nortel VPN Router Installation — VPN Router 600
50 Chapter 3 Configuring the management IP interface
3
For information about configuring the VPN Router 600, go to Nortel VPN
Router Configuration — Basic Features (NN46110-500).
Troubleshooting
If you cannot connect to the VPN Router 600 using your browser, check the
following items:
•
•
•
•
•
Ensure that you entered the correct IP address in the browser window.
Type a known URL in the browser window to make sure that your network
connection is good.
Check that the management IP address that you configured is on the same
subnet as the physical LAN attached to the gateway.
Ensure that your PC is running a supported browser (see“Testing the
configuration” on page 49).
Check the physical connections on the VPN Router 600, especially the LAN
cable and the power cord.
If you still cannot connect to the VPN Router 600 using a browser, connect a
terminal or PC to the gateway with the serial cable and check the management IP
address listed in the serial menu (see “Configuring the management IP address”
on page 45). Reconfigure the management IP address if necessary.
If you cannot resolve the problem, contact the Nortel Technical Solutions Center
closest to you (see “How to get help” on page 17).
NN46110-308 02.01
51
Chapter 4
Installing option cards and DIMMs
This chapter provides instructions on how to install and replace the following field
replaceable units (FRU) in the VPN Router 600:
•
•
LAN, WAN, and serial interface cards
Dual inline memory module (DIMM)
To install an interface card or DIMM, you must remove the VPN Router 600
chassis from its steel enclosure.
This chapter contains the following topics:
Topic
Page
Shutting down the system to add or replace hardware
52
Opening the Nortel VPN Router 600
52
Installing and replacing an option card
56
Replacing a DIMM
61
Nortel VPN Router Installation — VPN Router 600
52 Chapter 4 Installing option cards and DIMMs
Shutting down the system to add or replace hardware
Shut down the VPN Router 600, and unplug it to install or replace an option card
or to replace the DIMM.
To shut down the VPN Router 600:
1
Use the Web graphic user interface (GUI) or the command line interface
(CLI) to shut down the gateway.
•
•
Web GUI: Choose Admin > Shutdown. Select the option to power off the
gateway after shutdown.
CLI: Use the reload command to shut down the system. For example,
enter reload power-off disable-logins “Upgrade hardware”
(for the complete syntax of the reload command, see the Nortel VPN
Router Using the Command Line Interface (NN46110-507).
2
Wait for the system to shut down. You need to wait several minutes.
3
Remove all interface cables from the rear of the chassis.
4
Disconnect the power cord from the power outlet.
5
Disconnect the power supply cable from the VPN Router 600 DC input port.
Warning: Risk of electric shock
Turn off the VPN Router 600 and unplug it before you attempt to
remove or install an option card or DIMM.
Opening the Nortel VPN Router 600
To install an interface card or to replace the DIMM, you must remove the VPN
Router 600 chassis from its steel enclosure.
To access the chassis:
NN46110-308 02.01
Chapter 4 Installing option cards and DIMMs 53
1
Shut down the VPN Router 600, and then unplug it as described in “Shutting
down the system to add or replace hardware” on page 52.
Warning: Risk of electric shock
Turn off the VPN Router 600 and unplug it before you attempt to
remove or install an option card or DIMM.
2
Turn the VPN Router 600 over to see the bottom of the gateway.
3
Use a Phillips screwdriver to remove the four screws that secure the bottom to
the chassis (Figure 11).
Figure 11 Removing the screws from the bottom of the VPN Router 600
1
2
3
4
CS60003A
Nortel VPN Router Installation — VPN Router 600
54 Chapter 4 Installing option cards and DIMMs
4
Grasp the rear of the chassis, and firmly pull the chassis toward you to loosen
the chassis from the steel enclosure (Figure 12).
You can gently shake the chassis so that it slips outward and into your hand, or
you can pull gently on the I/O expansion bay.
Figure 12 Removing the chassis from the steel enclosure
I/O EXPA
NSION
CONSOL
E
BAY
LAN 1
FD
LAN 0
RC
DC INPU
+12V-1. T
7A
-12V-0.1
A
+5V-10
A
75W MA
X
CS60004A
The system board is now exposed. Figure 13 on page 55 shows the location of the
option card slot and the DIMM slot on the VPN Router 600 system board.
NN46110-308 02.01
Chapter 4 Installing option cards and DIMMs 55
Figure 13 VPN Router 600 system board
Option card slot
DIMM slot
CS60005A
Warning: Risk of injury
Beware of danger if you incorrectly replace the battery. Replace the
battery with the same type or an equivalent battery only, as
recommended by the manufacturer’s instructions. In spite of this
warning, which is mandated for regulatory approval, you must not
change the battery. If you suspect a dead battery, contact Nortel
Customer Support.
Nortel VPN Router Installation — VPN Router 600
56 Chapter 4 Installing option cards and DIMMs
Installing and replacing an option card
The VPN Router 600 has one expansion slot for option cards (Figure 13 on
page 55). This section provides instructions on installing a LAN, WAN, or serial
option card in the VPN Router 600 or, if necessary, replacing the installed card.
You can install the following option cards in the VPN Router 600:
Note: The 1000BASE-T (1000 GT) Ethernet interface card only
operates at 10/100 Mbit/s on the VPN Router 600.
.
Table 12 Supported option cards for the Nortel VPN Router 600 600
Option card
Maximum number
10/100BASE-TX Ethernet interface
1000BASE-T (1000 GT) Ethernet interface
1
1
1
56/64K channel service unit/digital service unit (CSU/DSU) WAN
interface2
1
Asymmetric digital subscriber line (ADSL) WAN interface3
1
Integrated Services Digital Network (ISDN) BRI S/T or U interface4
1
T1 CSU/DSU WAN interface (full-height)
1
T1/E1 CSU/DSU WAN interface (half-height)
1
V.90 modem interface5
1
Single V.35/X.21 WAN interface (full-height)
1
Single V.35/X.21 WAN interface (half-height)6
1
1 The VPN Router 600 must be running Version 5.05.330, 6.05.140 and later, 7.00.062, 7.05.100
and later, or 7.05.300 and later. The VPN Router 600 supports 10/100 Mbps operation only.
2 The VPN Router 600 must be running Version 5.0 or later.
3 The VPN Router 600 must be running Version 4.90 or later.
4 The VPN Router 600 must be running Version 4.80 or later.
5 The VPN Router 600 must be running Version 4.80 or later.
6 The VPN Router 600 must be running Version 4.80 or later.
NN46110-308 02.01
Chapter 4 Installing option cards and DIMMs 57
To install or replace a LAN, WAN, or serial interface card:
1
Shut down the VPN Router 600 using the Web GUI or the CLI, and then
unplug it as described in “Shutting down the system to add or replace
hardware” on page 52.
Warning: Risk of electric shock
Turn off the VPN Router 600 and unplug it before you attempt to install
an option card.
2
Remove the chassis from the steel enclosure (see “Opening the Nortel VPN
Router 600” on page 52).
3
Attach an antistatic wrist strap.
Caution: Risk of equipment damage
Electrostatic discharge can damage VPN Router 600 components.
Nortel VPN Router Installation — VPN Router 600
58 Chapter 4 Installing option cards and DIMMs
4
Remove the blank PCI bracket by inserting a Phillips screwdriver into the slot
at the right of the blank PCI bracket and rotating the screw counterclockwise
(Figure 14).
Figure 14 Removing the blank bracket from the option card slot
Option card slot
Blank PCI bracket
Phillips screwdriver
Screwdriver
slot
Motherboard
CS60010A
5
Slide the option card into the option card slot (Figure 15 on page 59).
Do not bend the copper fingers in the slot.
NN46110-308 02.01
Chapter 4 Installing option cards and DIMMs 59
Figure 15 Inserting the option card
Option card
slot
Option card
Motherboard
CS60006A
Seat the option card firmly and evenly in the card slot with the left tabbed end
of the card seated in the card slot. If you do not seat the card properly, it does
not work.
6
Replace the screw at the right end of the PCI bracket (Figure 16 on page 60).
Nortel VPN Router Installation — VPN Router 600
60 Chapter 4 Installing option cards and DIMMs
Figure 16 Securing the option card in the slot
Option card slot
Option card
Phillips screwdriver
Screwdriver slot
Motherboard
CS60007A
7
Slide the chassis into the steel enclosure (Figure 17).
Figure 17 Replacing the chassis in the steel enclosure
I/O EXPA
NSION
CONSOL
E
BAY
LAN 1
FD
LAN 0
RC
DC INPU
+12V-1. T
7A
-12V-0.1
A
+5V-10
A
75W MA
X
CS60009A
NN46110-308 02.01
Chapter 4 Installing option cards and DIMMs 61
8
Replace the four Phillips screws that secure the bottom panel to the chassis
(Figure 11 on page 53).
9
Connect the cables to the system ports and to the option card port.
10 Plug the cable attached to the external power supply into the receptacle
labeled “DC Input” on the rear of the VPN Router 600.
11 Plug the female end of the power cord into the external power supply pack if
necessary.
12 Plug the male end of the power cord into a surge protector
13 Plug the surge protector into the power outlet.
The VPN Router 600 begins to boot.
Note: The VPN Router 600 has no power switch. Connecting the VPN
Router 600 to a power supply turns the gateway on.
Replacing a DIMM
The VPN Router 600 has one slot for a dual inline memory module (DIMM). If
you have a VPN Router 600 with a 64 MB DIMM, you can upgrade system
memory by replacing the installed DIMM with a 128 MB DIMM.
Note: Nortel ships newer VPN Router 600 gateways with 128 MB of
memory installed. If you purchased your VPN Router 600 after January
2002, your gateway has 128 MB of memory.
Caution: Use of a memory module not purchased from Nortel can
render void your warranty or your service contract.
Nortel VPN Router Installation — VPN Router 600
62 Chapter 4 Installing option cards and DIMMs
To replace the DIMM in the VPN Router 600:
1
Shut down the VPN Router 600 using the Web GUI or the CLI, and then
unplug it as described in “Shutting down the system to add or replace
hardware” on page 52.
Warning: Risk of electric shock
Turn off the VPN Router 600 and unplug it before you attempt to replace
the DIMM.
2
Remove the chassis from the steel enclosure (see “Opening the Nortel VPN
Router 600” on page 52).
3
Attach an antistatic wrist strap.
Caution: Risk of equipment damage
Electrostatic discharge can damage VPN Router 600 components.
4
Locate the DIMM slot on the system board (Figure 13 on page 55).
5
Pull the locking levers back to release the DIMM.
The DIMM snaps up from the circuit board.
6
Pull the DIMM out of the slot.
7
Insert the new DIMM into the slot at a 45 degree angle (Figure 18).
Use the alignment keys on the DIMM to properly position the DIMM in the
connector.
NN46110-308 02.01
Chapter 4 Installing option cards and DIMMs 63
Figure 18 Installing a DIMM
Motherboard
Socket keys
Alignment keys
CS60008A
8
Gently press down on the DIMM until the locking levers lock it into position.
9
Slide the chassis into the steel enclosure (Figure 17 on page 60).
10 Replace the four Phillips screws that secure the bottom panel to the chassis
(Figure 11 on page 53).
11 Connect the cables to the system ports and to the option card port.
12 Plug the cable attached to the external power supply into the receptacle
labeled “DC Input” on the rear of the VPN Router 600.
13 Plug the female end of the power cord into the external power supply pack if
necessary.
14 Plug the male end of the power cord into a surge protector
15 Plug the surge protector into the power outlet.
The VPN Router 600 begins to boot.
Note: The VPN Router 600 has no power switch. Connecting the VPN
Router 600 to a power supply turns the gateway on.
Nortel VPN Router Installation — VPN Router 600
64 Chapter 4 Installing option cards and DIMMs
NN46110-308 02.01
65
Chapter 5
Using recovery mode
The VPN Router 600 does not have a floppy disk drive, so the software image is
built into the onboard flash operating system. Recovery mode on the VPN Router
600 is also built into the flash operating system. You use recovery mode to restore
software to a VPN Router 600.
Some Web pages refer to “the recovery diskette” or “the diskette.” In the case of
the VPN Router 600, “the diskette” is a virtual diskette. In all other respects,
recovery mode on a VPN Router 600 works the same way that it does on VPN
Routers that have floppy disk drives.
Note: In addition, the VPN Router 600 does not have a Reset button. If
you need to reset a VPN Router 600, you remove power from the
gateway and then restore power.
To enter recovery mode:
1
Plug in the console cable, the LAN 0 cable, and the DC input cable from the
VPN Router 600 power supply (Figure 2 on page 31).
2
Start HyperTerminal (or another terminal emulation program) on your PC and
connect to the console port of the VPN Router 600.
3
Apply AC power to the power supply.
4
Press the RC (recovery) switch on the rear of the VPN Router 600 by
inserting a paper clip into the hole marked “RC” on the rear of the chassis
(Figure 2 on page 31). The RC switch is located between the LAN 0 cable and
the DC input cable.
Nortel VPN Router Installation — VPN Router 600
66 Chapter 5 Using recovery mode
On your console you can see the BIOS banner and the Nortel VPN Router
banner. Then, you observe the unit execute its power-on self-test. You can
press the switch anytime during the power tests. A momentary press is all that
is required. You do not need to hold the button down.
Note: After the console completes the power-on self-test, it displays the
message Booting recovery image.
Booting the recovery image takes approximately 40 seconds. After the
recovery image boots, the VPN Router 600 displays the welcome message,
the recovery image version, and a prompt for you to enter the administrator’s
user name. At this point, you are in recovery mode.
5
Enter a management IP address, subnet mask, and gateway if they are not
already assigned. You do this from the console menu after logging in as an
administrator.
When the unit has a management IP address, you can manage the unit from
the Web interface.
Note: The switch marked FD is reserved for future use. Pressing this
switch has no effect.
From the Web browser, enter the management IP address of the VPN Router 600.
The Recovery Diskette screen appears (Figure 19 on page 67). From this screen,
you can perform the following tasks:
•
•
•
•
•
•
NN46110-308 02.01
Restore the factory default configuration or the backup configuration.
Reformat the hard disk of the VPN Router 600.
Apply a new software version to the VPN Router 600.
Perform file maintenance.
View the Event log.
Restart the system.
Chapter 5 Using recovery mode 67
Figure 19 Recovery Diskette screen
Nortel VPN Router Installation — VPN Router 600
68 Chapter 5 Using recovery mode
1
Restore the configuration:
To restore the factory default configuration or the backup configuration, do
one of the following:
•
Restore the factory default configuration by selecting Restore Factory
Configuration, then clicking Restore to return the VPN Router 600 to its
original factory default configuration. This option erases data contained
in flash memory and also in the configuration file.
Caution: Risk of configuration loss
If you select this option, you must rebuild your entire configuration
again from scratch
A message specifies the result of the Factory Configuration reset action.
•
Or, you can restore the gateway’s previously backed-up configuration by
clicking Restore. If you previously chose to automatically back up the file
systems, then the Backup Server Host (or IP address) and Path Name,
User ID, and Password appear in the table.
Choose the Partial Backup option to restore the configuration files, log
files, or system files from a partial backup.
Click the radio button of the preferred backup server. The backed-up file
system, including software image and configuration files, from the latest
backup copy residing on the designated server is restored onto the hard
drive of your gateway.
You can use the same backup server for multiple gateways. Each gateway
creates a unique directory based on its serial number. The following
example shows the host, path, and serial number:
C:/software/backup/v101/SN01001
The serial number differentiates backup configurations from multiple
gateways that are saved on the same backup server. The serial number
uniquely identifies each gateway’s backup data.
A blank row in the server backup field always appears to allow you to
manually enter a backup server in case you did not configure automatic
backup server locations.
NN46110-308 02.01
Chapter 5 Using recovery mode 69
•
Alternatively, you can restore a new factory default software image and file
system to the VPN Router 600 hard disk. Specify the name or address and
path of the network file server onto which the software from the Nortel CD
has been installed.
Note: This option restores the disk to an operable but “clean” condition
(for example, configuration values are at factory defaults).
To view your gateway’s serial number when the gateway is operational, click
Status > System from the navigational menu. The serial number is also listed
on the bar code label on the back of the gateway.
2
Click Reformat your Switch’s Hard Disk if you must reformat the hard disk,
for example if you:
— Have problems restoring your configuration that are not caused by the
network or the file/backup server from which the file restoration is being
retrieved.
— Want to reconfigure the VPN Router 600 from scratch.
Caution: Risk of data loss
If you select this option, you erase all information that previously resided
on the hard disk.
A message indicates whether the reformatting of the hard disk was successful.
3
Click the list box to view the available software image and file systems that
are stored on the remote disk and select the image version that you want to
activate.
4
Click Files to display the File Maintenance screen, which allows you to view
the entire hard disk file system.
5
Click View to display the Event Log beneath the Recovery Diskette display.
This is especially useful if a Restore operation fails.
6
Reset the system after recovery operation by unplugging the unit. Either AC
or DC power may be interrupted momentarily to accomplish this. Then
reposition your Web browser to the management IP address, and press Reload
or Refresh from your browser menu to access the management page of the
software running on the hard disk.
Nortel VPN Router Installation — VPN Router 600
70 Chapter 5 Using recovery mode
NN46110-308 02.01
71
Appendix A
Technical specifications
This appendix provides technical specifications for the VPN Router 600 chassis
and its interfaces.
Chassis specifications
Table 13 lists physical, electrical, and environmental specifications for the
chassis.
Table 13 Physical, electrical, and environmental specifications
Specification
Description
Physical
Height
4 in. (10.16 cm)
Width
8 in. (20.32 cm)
Depth
10.75 in. (27.30 cm)
Weight
7 lbs. (3.175 kg)
Electrical
Voltage
100–240 VAC
Current
1.9 A
Frequency
47–63 Hz
Environmental
Operating temperature
32–110oF (0–45oC)
Relative humidity
10–90% noncondensing
Nortel VPN Router Installation — VPN Router 600
72 Appendix A Technical specifications
System ports
The VPN Router 600 system board provides the following built-in interfaces:
•
•
10/100BASE-TX Ethernet LAN ports
Serial port
This section provides information about the 10/100BASE-TX Ethernet LAN ports
and the serial port on the system board.
10/100BASE-TX Ethernet LAN port
The system board provides two 10/100BASE-TX Ethernet LAN interfaces on the
rear of the chassis. (LAN 0 is generally used for Web management, and LAN 1 is
generally used as a public LAN.) These interfaces accommodate an RJ-45
straight- through cable. Depending on whether you use the interface for
10BASE-T or 100BASE-TX operation, select cables for the interface as follows:
•
100BASE-TX connections require Category 5 twisted-pair wire. The
100BASE-TX specification supports 100 Mb/s transmission over two pairs of
Category 5 twisted-pair Ethernet wiring: one pair each for transmit and
receive operations.
Nortel recommends a maximum length of 100 meters for the cable segment
between a 100BASE-TX repeater and a workstation (due to signal timing
requirements). This wiring scheme complies with the EIA 568 wiring
standard.
•
10BASE-T connections can use Category 3, 4, or 5 twisted-pair wiring.
Figure 20 on page 73 shows the 10/100BASE-TX Ethernet connector and its
pinouts.
NN46110-308 02.01
Appendix A Technical specifications 73
Figure 20 10/100BASE-TX Ethernet connector
RD+RD- TD+ TD12345678
CS260010A
Table 14 provides the 10/100BASE-TX Ethernet port pinouts.
Table 14 10/100BASE-TX Ethernet port pinouts
Pin
Description
1
RD +
2
RD -
3
TD +
6
TD -
Serial port
The system board provides a serial port on the rear of the chassis to enable
out-of-band management. Using the serial port, you can assign the management
IP address and subnet mask to the newly installed gateway (for more information,
see Chapter 3, “Configuring the management IP interface,” on page 43).
The serial cable provided with the VPN Router 600 is a DB9/DB25-to-DB9/DB25
cable. This cable provides a crossover connection (transmit-to-receive and
receive-to-transmit). The DB9 connector goes into the gateway and the other DB9
or DB25 connector goes into your workstation (Figure 21 on page 74).
Nortel VPN Router Installation — VPN Router 600
74 Appendix A Technical specifications
Figure 21 Serial cable (9-pin D-sub plug to RS-232-C modem plug)
10 ft
(3.05 m)
Pin 5
Pin 1
Pin 9
Pin 6
Pin 1
Pin 13
Pin 14
Pin 25
9-position D-sub receptacle with screw locks
(ground shield connected to backshell)
25-position D-sub plug with screw locks
(ground shield connected to backshell)
CAB0056A
Table 15 provides the multiple DB9/DB25 serial interface cable pinouts.
Table 15 Multiple DB9 and DB25 connector pinouts
Serial port
DB9 connector
Serial port
DB25 connector
Serial port
DB25 connector
Serial port
DB9 connector
Pinout
Signal
Pinout
Signal
Pinout
Signal
Pinout
Signal
2
RXD
3
TXD
>
2
RXD
3
TXD
3
TXD
2
RXD
>
3
TXD
2
RXD
4
DTR
20
DSR
>
6
DTR
6
DSR
5
Ground
7
Ground
>
7
Ground
5
Ground
6
DSR
6
DTR
>
20
DSR
4
DTR
7
RTS
4
RTS
>
5
CTS
8
CTS
8
CTS
5
CTS
>
4
RTS
7
RTS
NN46110-308 02.01
Appendix A Technical specifications 75
Modem cable specifications
If you need to connect a modem to a VPN Router 600, you must obtain an
appropriate modem cable. The modem cable must have a 9-pin D-sub plug that
connects to the VPN Router 600 serial port and a 25-pin D-sub plug that connects
to the RS-232-C modem port (Figure 22).
Figure 22 Modem cable (9-pin D-sub plug to RS-232-C modem plug)
10 ft
(3.05 m)
Pin 5
Pin 1
Pin 9
Pin 6
9-position D-sub receptacle with screw locks
(ground shield connected to backshell)
Pin 1
Pin 13
Pin 14
Pin 25
25-position D-sub plug with screw locks
(ground shield connected to backshell)
CAB0056A
Table 16 provides the modem cable pinouts.
Table 16 Modem cable pinouts
Nortel termination
Modem termination
Signal
Pin # to Pin #
Signal
Data Carrier Detect
1
8
Data Carrier Detect
Transmit Data (TXD)
2
2
Transmit Data (TXD)
Receive Data (RXD)
3
3
Receive Data (RXD)
Data Set Ready
4
6
Data Set Ready
Data Terminal Ready
6
20
Data Terminal Ready
Clear to Send
7
5
Clear to Send
Request to Send
8
4
Request to Send
Nortel VPN Router Installation — VPN Router 600
76 Appendix A Technical specifications
Hardware option cards
The VPN Router 600 has one expansion PCI slot that supports any of the
following option cards:
•
•
•
•
•
•
•
•
•
10/100BASE-TX Ethernet interface card
1000BASE-T (1000 GT) Ethernet interface card
56/64K CSU/DSU WAN interface card
ADSL WAN interface card
ISDN BRI S/T or U interface card
T1 CSU/DSU WAN interface card (full-height card)
T1/E1 CSU/DSU WAN interface card (half-height card)
Single V.35/X.21 WAN interface card
V.90 modem interface card
This section provides information about the option cards, including the connector
and the cable pinouts for each supported network interface card. For instructions
on installing an option card, see Chapter 4, “Installing option cards and DIMMs,”
on page 51.
10/100BASE-TX Ethernet interface card
The 10/100BASE-TX Ethernet interface card has a single RJ-45 connector that
provides the signals needed to interface to 10BASE-T and 100BASE-TX Ethernet
equipment.
Figure 23 shows the 10/100BASE-TX Ethernet interface card.
100TX
ACT/LINK
DATA
Figure 23 10/100BASE-TX Ethernet interface card
CS260009A
For information about the cables that you can connect to this interface and the
cable pinouts, see “10/100BASE-TX Ethernet LAN port” on page 72.
NN46110-308 02.01
Appendix A Technical specifications 77
1000BASE-T (1000 GT) Ethernet interface card
The 1000BASE-T (1000 GT) Ethernet card replaces the 10/100BASE-TX
Ethernet card (see the previous section). This card provides 10/100/1000 Mbit/s
Ethernet services and supports autonegotiation. The card supports the IEEE
802.3ab standard and provides RJ-45/CAT 5 interconnection. It can operate in
either full or half duplex mode at 10/100 Mbit/s, and in full duplex mode at 1
Gbit/s. At 1 Gbit/s, autonegotiation must be used.
Note: The 1000BASE-T (1000 GT) Ethernet interface card can only
operate at 10/100 Mbit/s on the VPN Router 600.
The VPN Router 600, 1100, 1600 and 2600 only support 10/100 Mbit/s operation
for the 1000BASE-T (1000 GT) Ethernet card. To ensure reliable speed/duplex
operation on these platforms, Nortel recommends that both the interface and the
attached devices are hard-coded to the appropriate matching 10/100 speed and
duplex settings.
For the 1000BASE-T (1000 GT) Ethernet interface card to be recognized by the
system, the minimum required VPN Router operating software is:
•
•
•
•
•
5.05.330
6.05.140 and all subsequent versions
7.00.062
7.05.100 and all subsequent versions (FIPS branch)
7.05.300 and all subsequent versions
The following figure shows the 1000BASE-T (1000 GT) Ethernet interface
full-height card for VPN Router.
Nortel VPN Router Installation — VPN Router 600
78 Appendix A Technical specifications
Figure 24 1000BASE-T (1000 GT) Ethernet interface card
Select cables for this card as follows. Keep in mind that this card is
auto-negotiating and uses the highest possible data rate:
•
For 100BASE-TX operation, use Category 5 twisted-pair wiring: one pair
each for transmit and receive operations. The cable must comply with the
EIA 568 wiring specification. Nortel recommends a maximum length of 100
meters for the cable segment.
For 10BASE-T operation, use Category 3, 4, or 5 twisted-pair wiring.
•
The following table provides the pinouts for the 1000BASE-T (1000 GT) Ethernet
interface card..
Table 17 1000BASE-T (1000 GT) Ethernet pinouts
12345678
CS260010A
Pin
Description
1
TP0+
2
TP0-
3
TP1+
4
TP2+
5
TP2-
6
TP1-
7
TP3+
8
TP3-
56/64K CSU/DSU WAN interface card
The 56/64K CSU/DSU WAN interface card has a single RJ-48 connector that
provides the signals needed to interface to network equipment. Figure 25 shows
the 56/64K CSU/DSU WAN interface card.
NN46110-308 02.01
Appendix A Technical specifications 79
Figure 25 56/64K CSU/DSU WAN interface card
56/64K
DDS
The connector on the 56/64K CSU/DSU WAN interface card accommodates an
8-pin RJ-48 modular patch cord. These cables are commonly sold as Category 5,
or Ethernet, cables.
Note: Nortel does not supply an interface cable with the
56/64K CSU/DSU WAN interface card.
Use cable that is wired in accordance with EIA-568-A wiring style. This wiring
style ensures that a twisted pair inside the patch cord carries the transmit signal
(pins 1 and 2) and the receive signal (pins 7 and 8). Nortel recommends that you
use factory-made patch cords.
You connect the 56/64K CSU/DSU WAN interface card to the service provider
network using a straight-through cable or a crossover cable, depending on how the
service provider wired its jack.
•
•
For a straight-through connection, you can use a standard Category 5
(Ethernet) straight-through cable.
For a crossover connection, you cannot use a standard Category 5 crossover
cable. Do not interchange the 56/64K CSU/DSU crossover cable and the
Ethernet crossover cable.
Table 18 on page 79 provides the 56/64K CSU/DSU cable pinouts for a crossover
connection.
Table 18 56/64K CSU/DSU cable pinouts for crossover connection
Nortel termination
Remote termination
Signal
Pin # to Pin #
Signal
Transmit tip
1
7
Receive tip
Transmit ring
2
8
Receive ring
Nortel VPN Router Installation — VPN Router 600
80 Appendix A Technical specifications
Table 18 56/64K CSU/DSU cable pinouts for crossover connection
Nortel termination
Remote termination
not used
3
3
not used
not used
4
4
not used
not used
5
5
not used
not used
6
6
not used
Receive tip
7
1
Transmit tip
Receive ring
8
2
Transmit ring
The cable operates properly if you do not connect pins 3, 4, 5, and 6.
Caution: For crossover connections, do not use Ethernet cable. If you
use Ethernet cable, the link cannot be established.
Table 19 provides the 56/64K CSU/DSU cable pinouts for a straight-through
connection.
Table 19 56/64K CSU/DSU cable pinouts for straight-through connection
Nortel termination
Remote termination
Signal
Pin # to Pin #
Signal
Transmit tip
1
1
Transmit tip
Transmit ring
2
2
Transmit ring
not used
3
3
not used
not used
4
4
not used
not used
5
5
not used
not used
6
6
not used
Receive tip
7
7
Receive tip
Receive ring
8
8
Receive ring
NN46110-308 02.01
Appendix A Technical specifications 81
ADSL WAN interface card
The ADSL Annex A and Annex B WAN interface cards have a single RJ-11
connector that provides the signals needed to interface to the digital subscriber
line access multiplexer (DSLAM) and to telephone equipment.
Figure 26 shows the ADSL WAN interface card.
Note: The ADSL Annex A and ADSL Annex B cards look identical.
Figure 26 ADSL WAN interface card
ADSL
RX/TX
CONN
Included in the accessory box is a 7-foot RJ-11 cable to attach to the DSLAM.
Table 20 provides the ADSL port pinouts.
Table 20 ADSL cable pinouts
Pin
Function
1
N/C
2
Tip
3
Ring
4
N/C
Nortel VPN Router Installation — VPN Router 600
82 Appendix A Technical specifications
ISDN BRI interface card
The ISDN BRI S/T and ISDN BRI U interface cards have a single RJ-45
connector that provides the signals needed to interface to ISDN equipment. (To
connect the ISDN S/T interface to the ISDN network, you must attach an external
NT-1 device to the RJ-45 connector.)
Figure 27 shows the ISDN BRI S/T interface card and the ISDN BRI U interface
card. The two cards look identical.
Figure 27 ISDN BRI S/T interface card and ISDN BRI U interface card
The connector on the ISDN BRI S/T and ISDN BRI U interface cards
accommodates an 8-pin RJ-45 modular patch cord. These cables are commonly
sold as Category 5, or Ethernet, cables.
Note: Nortel does not supply a cable with the ISDN BRI interface cards.
Table 21 provides the ISDN BRI S/T cable pinouts.
Table 21 ISDN BRI S/T cable pinouts
Pin
Function
1
N/C
2
N/C
3
Receive +
4
Transmit +
5
Transmit -
6
Receive -
7
N/C
8
N/C
NN46110-308 02.01
Appendix A Technical specifications 83
Table 22 provides the ISDN BRI U cable pinouts.
Table 22 ISDN BRI U cable pinouts
Pin
Function
1
N/C
2
N/C
3
N/C
4
U interface network connection (tip)
5
U interface network connection (ring)
6
N/C
7
N/C
8
N/C
T1/E1 CSU/DSU WAN interface card
The T1/E1 CSU/DSU WAN interface card has a single connector that provides the
signals needed to interface to T1 or E1 equipment. This interface card ships as a
half-height card and as a full-height card.
Figure 28 shows the T1/E1 CSU/DSU WAN interface card (half-height card).
Figure 28 T1/E1 CSU/DSU WAN interface card (half-height card)
Note: For E1 service, you must install the half-height version of the
T1/E1 CSU/DSU WAN interface card.
Figure 29 on page 84 shows the T1/E1 CSU/DSU WAN interface card
(full-height card).
Nortel VPN Router Installation — VPN Router 600
84 Appendix A Technical specifications
Figure 29 T1/E1 CSU/DSU WAN interface card (full-height card)
CS160012A
The connector on the T1/E1 CSU/DSU WAN interface card accommodates an
8-pin RJ-48 modular patch cord. These cables are sold as Category 5, or Ethernet,
cables.
Note: Nortel does not supply the T1/E1 CSU/DSU WAN interface
cable with the WAN interface card.
Use cable that is wired in accordance with EIA-568-A wiring style. This wiring
style ensures that the transmit signal (pins 4 and 5) and the receive signal (pins 1
and 2) are carried on a twisted pair inside the patch cord. The use of factory made
patch cords is strongly recommended.
You connect the T1/E1 CSU/DSU WAN interface card to the service provider
network using a straight-through cable or a crossover cable, depending on how the
service provider wired its jack.
•
•
For a straight-through connection, you can use a standard Category 5
(Ethernet) straight-through cable.
For a crossover connection, you cannot use a standard Category 5 crossover
cable. The T1/E1 CSU/DSU crossover cable and the Ethernet crossover cable
are not interchangeable.
Table 23 provides the T1/E1 CSU/DSU cable pinouts for a crossover connection.
Table 23 T1/E1 CSU/DSU cable pinouts for crossover connection
Standard-wired
end 8-pin male
Signal name
Pair number
and conductor
Special-wired
end 8-pin male
1
RXDA<-TXDA
wht/org pair 2A
5
2
RXDB<-TXDB
orange pair 2B
4
3
not used
wht/grn pair 3A
3
4
TXDB->RXDB
blue pair 1B
2
NN46110-308 02.01
Appendix A Technical specifications 85
Table 23 T1/E1 CSU/DSU cable pinouts for crossover connection
Standard-wired
end 8-pin male
Signal name
Pair number
and conductor
Special-wired
end 8-pin male
5
TXDA->RXDA
wht/blu pair 1A
1
6
not used
green pair 3B
6
7
not used
wht/brn pair 4A
7
8
not used
brown pair 4B
8
The cable operates properly if you do not connect pins 3, 6, 7, and 8.
Caution: For crossover connections, do not use Ethernet cable. If you
use Ethernet cable, the T1/E1 CSU/DSU does not work to specifications,
and these conditions can corrupt the data.
Table 24 provides the T1/E1 CSU/DSU cable pinouts for a straight-through
connection.
Table 24 T1/E1 CSU/DSU cable pinouts for straight-through connection
Nortel termination
Remote termination
Signal
Pin # to Pin #
Signal
Receive A (RXDA)
1
1
Receive A (RXDA)
Receive B (RXDB)
2
2
Receive B (RXDB)
not used
3
3
not used
Transmit B (TXDB)
4
4
Transmit B (TXDB)
Transmit A (TXDA)
5
5
Transmit A (TXDA)
not used
6
6
not used
not used
7
7
not used
not used
8
8
not used
Nortel VPN Router Installation — VPN Router 600
86 Appendix A Technical specifications
Single V.35/X.21 WAN interface card
The single V.35/X.21 WAN interface card has a single DB28S connector that
provides the signals needed to interface to V.35 and X.21 equipment. Figure 30
shows the single V.35/X.21 WAN interface card.
Figure 30 Single V.35/X.21 WAN interface card
You need a DSU/CSU (digital service unit/channel service unit) between the
WAN connection and the gateway. You can order a V.35 or X.21 cable to attach to
the connector. This cable enables the WAN adapter to function as DTE (data
terminal equipment).
Table 25 provides the V.35 cable pinouts. Table 26 on page 88 provides the X.21
cable pinouts. (The pair suffix A or B refers to an individual wire within a twisted
pair.)
Table 25 V.35 cable pinouts
Standard-wired
end 28-pin male
Signal name
Pair number
and conductor
Special-wired
end 34-pin male
2
TXDA
pair 1A
P
14
TXDB
pair 1B
S
3
RXDA
pair 2A
R
16
RXDB
pair 2B
T
15
TXCA
pair 3A
Y
12
TXCB
pair 3B
AA
17
RXCA
pair 4A
V
9
RXCB
pair 4B
X
24
SCTEA
pair 5A
U
11
SCTEB
pair 5B
W
4
RTSA
pair 6A
C
19
RTSB
pair 6B
no conn
NN46110-308 02.01
Notes
Note 1
Appendix A Technical specifications 87
Table 25 V.35 cable pinouts (continued)
Standard-wired
end 28-pin male
Signal name
Pair number
and conductor
Special-wired
end 34-pin male
5
CTSA
pair 7A
D
13
CTSB
pair 7B
no conn
6
DSRA
pair 8A
E
22
DSRB
pair 8B
J
20
DTRA
pair 9A
H
23
DTRB
pair 9B
no conn
8
DCDA
pair 10A
F
10
DCDB
pair 10B
no conn
18
LL
pair 11A
L
21
RL
pair 11B
N
25
TM
pair 12A
NN
26
M0<-SIGNAL GROUND
pair 12B
B
Note 2
27
M1<-SIGNAL GROUND
pair 13A
B
Note 2
28
M2
pair 13B
no conn
Note 1
1
SHIELD
pair 14A
A
Notes 3,4
7
SIGNAL GROUND
pair 14B
B
Notes 2,4
Notes
Note 1
Note 1
Note 1
The following notes apply to the single V.35 DTE cable:
1. The term “no conn” means the wire is not connected to a pin in the 34-pin connector.
2. Wires 12B, 13A, and 14B connect to pin B in the 34-pin connector.
3. At each end, the cable shield and connector shell must connect respectively to pin A of the 34-pin connector and
pin 1 of the standard 28-pin connector.
4. Do not connect Shield to Signal Ground because these are separate signals.
Nortel VPN Router Installation — VPN Router 600
88 Appendix A Technical specifications
Table 26 provides the X.21 cable pinouts. (The pair suffix A or B refers to an
individual wire within a twisted pair.)
Table 26 X.21 cable pinouts
Standard-wired
end 28-pin male
Signal name
Pair number
and conductor
Standard-wired
end 15-pin male
2
TXDA
pair 1A
2
14
TXDB
pair 1B
9
3
RXDA
pair 2A
4
16
RXDB
pair 2B
11
15
TXCA
pair 3A
6
12
TXCB
pair 3B
13
17
RXCA
pair 4A
pair 5A
Note 1
9
RXCB
pair 4B
pair 5B
Note 1
24
SCTEA
pair 5A
pair 4A
Note 1
11
SCTEB
pair 5B
pair 4B
Note 1
4
RTSA
pair 6A
3
19
RTSB
pair 6B
10
5
CTSA
pair 7A
5
13
CTSB
pair 7B
12
6
DSRA
pair 8A
no conn
Note 2
22
DSRB
pair 8B
no conn
Note 2
20
DTRA
pair 9A
no conn
Note 2
23
DTRB
pair 9B
no conn
Note 2
8
DCDA
pair 10A
no conn
Note 2
10
DCDB
pair 10B
no conn
Note 2
18
LL
pair 11A
no conn
Note 2
21
RL
pair 11B
no conn
Note 2
25
TM
pair 12A
no conn
Note 2
26
M0
pair 12B
no conn
Note 2
27
M1
pair 13A
no conn
Note 2
28
M2<-SIGNAL GROUND
pair 13B
8
Note 3
NN46110-308 02.01
Notes
Appendix A Technical specifications 89
Table 26 X.21 cable pinouts (continued)
Standard-wired
end 28-pin male
Signal name
Pair number
and conductor
Standard-wired
end 15-pin male
Notes
1
SHIELD
pair 14A
1
Note 4,5
7
SIGNAL GROUND
pair 14B
8
Note 3,5
The following notes apply to the single X.21 cable:
1. Wires of pair 4 connect to wires of pair 5, but not to any pins in the DA-15.
2. The term “no conn” means the wire is not connected to a pin in the 15-pin connector.
3. Wires 13B and 14B connect to pin 8 in the 15-pin connector.
4. At each end, the cable shield and connector shell must connect to pin 1 of the connector.
5. Do not interconnect Shield to Signal Ground because these are separate signals.
V.90 modem interface card
The V.90 modem interface card has two RJ-11 connectors that provide the signals
needed to interface to an incoming telephone line and to telephone equipment.
Figure 31 shows the V.90 modem interface card.
LINE
PHONE
Figure 31 V.90 modem interface card
Included in the accessory box is a 7-foot RJ-11 cable to attach to a telephone jack.
Table 27 provides the V.90 modem port cable pinouts.
Table 27 V.90 modem cable pinouts
Pin
Function
1
N/C
2
Tip
3
Ring
4
N/C
Nortel VPN Router Installation — VPN Router 600
90 Appendix A Technical specifications
NN46110-308 02.01
91
Index
Numerics
cable pinouts 81
connector 81
described 81
installing 56
LEDs 39
10/100/1000BASE-X Ethernet interface card
LEDs 37
10/100BASE Ethernet interface card
connector 72
installing 56
10/100BASE system LAN port
cable specifications 72
connector 72
10/100BASE-TX Ethernet interface card
LEDs 36
10/100BASE-TX system LAN port
LEDs 35
10/100BASE-X Ethernet interface card
cable specifications 72
described 76
1000BASE-T (1000 GT) Ethernet interface card 77
LEDs 37
56/64K CSU/DSU WAN interface card
cable pinouts 79
connector 79
described 78
LEDs 38
A
AC power cord
connecting 32
ordering 27
requirements 32
B
backup configuration 68
browsers, supported 49
C
cables
available from Nortel 30
connecting to the gateway 31
ordering 30
power. See AC power cord
technical specifications
100BASE-TX connector 72
10BASE-T connector 72
56/64K CSU/DSU WAN interface 78
ADSL WAN interface 81
ISDN BRI interface 82
modem 75
serial interface 73
single V.35/X.21 WAN interface 86
T1/E1 CSU/DSU WAN interface 84
V.90 modem interface 89
Category 5 wiring requirements 72
accessories, hardware, shipped with the gateway 27
chassis
installing 28
specifications 71
acronyms 22
configuring the management IP address 45
ADSL WAN interface card
connecting
Nortel VPN Router Installation — VPN Router 600
92 Index
by Express Routing Code 18
by phone 18
latest updates 17
Nortel distributor 18
Nortel Web site 17
cables 31
power cord 32
serial cable to the gateway 45
to the gateway using a browser 49
connectors
10/100BASE Ethernet interface card 76
10/100BASE system LAN port 72
56/64K CSU/DSU WAN interface 79
ADSL WAN interface 81
ISDN BRI S/T interface 82
single V.35/X.21 WAN interface 86
T1/E1 CSU/DSU WAN interface 83
V.90 modem interface 89
conventions, text 22
Help, how to get 17
I
installing the chassis
on a flat surface 28
prerequisites 26
interfaces, option card, technical specifications 76
interfaces, system, technical specifications 72
Internet Explorer, supported versions 49
D
default gateway, defined 44
DIMM (dual inline memory module), replacing 61
E
electrical specifications 71
environmental specifications 71
F
factory default configuration 66, 68
front panel LEDs 34
G
gateway, default, defined 44
GUI, Web-based 49
H
hard drive, reformatting 69
hardware accessories shipped with the gateway 27
hardware option cards
installing 56
specifications 76
Help
NN46110-308 02.01
IP address for managing the gateway. See
management IP address
ISDN BRI S/T interface card
cable pinouts 82
connector 82
installing 56
ISDN BRI U interface card
cable pinouts 83
installing 56
L
LAN interface cards
connector 72
LEDs 36
1000BASE-T (1000 GT) Ethernet 37
specifications 76
LAN port, system
cable specifications 72
connector 72
LEDs 35
LEDs
10/100BASE-TX Ethernet interface card 36
1000BASE-T (1000 GT) Ethernet interface card
37
56/64K CSU/DSU WAN interface card 38
ADSL WAN interface card 39
Index 93
front panel 34
single V.35/X.21 WAN interface card 41
system LAN port 35
T1/E1 CSU/DSU WAN interface card 40
M
main menu, serial interface 46
management IP address
configuring 45
defined 44
troubleshooting configuration of 50
verifying 49
mask, subnet, defined 44
modem cable
described 75
pinouts 75
V.90 modem interface 89
plug, AC power, specifications 32
power cord
connecting 32
ordering 27
requirements 32
publications
hard copy 24
related 23
R
reformatting the hard drive 69
requirements, site 28
S
serial cable, connecting to the gateway 45
N
Netscape Navigator, supported versions 49
NT-1 device, required for ISDN BRI S/T 82
O
option cards
installing 56
specifications 76
serial interface
cable pinouts 73
described 73
using to configure the management IP address 45
serial interface cards
installing 56
specifications
ISDN BRI 82
V.90 modem 89
serial main menu 46
P
physical specifications 71
pinouts
10/100BASE Ethernet connector 72
56/64K CSU/DSU WAN interface 79
ADSL WAN interface 81
ISDN BRI S/T interface 82
ISDN BRI U interface 83
modem cable 75
serial interface cable 73
single V.35 WAN interface 86
single X.21 WAN interface 88
T1/E1 CSU/DSU WAN interface 84
serial number, gateway 68
shipment contents 27
single V.35/X.21 WAN interface card
connector 86
installing 56
LEDs 41
V.35 pinouts 86
X.21 pinouts 88
site requirements 28
software version
applying 66
selecting 69
specifications
Nortel VPN Router Installation — VPN Router 600
94 Index
installing option cards 56
installing the chassis 28
removing from steel enclosure 52
replacing DIMM 61
shipment contents 27
shutting down 52
technical specifications 71
verifying connectivity 49
chassis 71
option cards 76
serial port 73
system ports 72
subnet mask, defined 44
system LAN port
cable specifications 72
connector 72
LEDs 35
system ports, specifications 72
T
T1/E1 CSU/DSU WAN interface card
cable pinouts 84
connector 83
installing 56
LEDs 40
technical publications 24
technical specifications 71
testing connectivity to the gateway 49
text conventions 22
troubleshooting the management IP address 50
U
user interface, Web 49
V
V.35/X.21 WAN interface card. See single
V.35/X.21 WAN interface card
V.90 modem interface card
cable pinouts 89
connectors 89
installing 56
verifying the management IP interface 49
VPN Router 600
configuring management IP address for 43
connecting cables to 29
connecting power cord 32
description 25
NN46110-308 02.01
W
WAN interface cards
installing 56
LEDs
56/64K CSU/DSU 38
ADSL 39
single V.35/X.21 41
T1/E1 CSU/DSU 40
specifications
56/64K CSU/DSU 78
ADSL 81
single V.35/X.21 86
T1/E1 CSU/DSU 83
Web interface to the gateway 49
wiring requirements, Category 5 72
X
X.21 WAN interface card. See single V.35/X.21
WAN interface card
Download PDF