Table of Contents
1
Hardware Installation and Connection..........................................................................1
1.1 Check Unpacked DVR ..........................................................................................1
1.2 About Front Panel and Rear Panel.....................................................................1
1.3 After Remove the Chassis....................................................................................1
1.4 HDD Installation .....................................................................................................1
1.5 Rack Installation.....................................................................................................2
1.6 Front Panel .............................................................................................................2
1.7 Rear Panel ..............................................................................................................5
1.7.1 General 2U series ............................................................................. 5
1.7.2 2U series (HD-SDI series)................................................................. 6
1.7.3 2U series (960H series)..................................................................... 7
1.8 Connection Sample ...............................................................................................8
1.8.1 2U series ........................................................................................... 8
1.8.2 2U series (HD-SDI series)................................................................. 9
1.8.3 2U series (960H series)................................................................... 11
1.9 Alarm Input and Output Connection .................................................................12
1.9.1 Alarm Input and Output Details ....................................................... 12
1.9.2 Alarm Input Port .............................................................................. 14
1.9.3 Alarm Output Port............................................................................ 14
2
Overview of Navigation and Controls..........................................................................16
2.1 Login, Logout & Main Menu ...............................................................................16
2.1.1
2.1.2
2.1.3
2.1.4
Login ............................................................................................... 16
Main Menu ...................................................................................... 17
Logout ............................................................................................. 17
Auto Resume after Power Failure ................................................... 18
2.2 Live Viewing..........................................................................................................18
2.3 Manual Record.....................................................................................................19
2.3.1 Manual record menu ....................................................................... 19
2.3.2 Basic operation ............................................................................... 19
2.3.3 Enable/disable record...................................................................... 20
i
2.3.4 Enable all channel recording ........................................................... 20
2.3.5 Stop all channel recording............................................................... 21
2.4 Search & Playback ..............................................................................................22
2.5 Schedule ...............................................................................................................25
2.5.1 Quick Setup..................................................................................... 26
2.5.2 Redundancy .................................................................................... 27
2.6 Snapshot ...............................................................................................................28
2.6.1
2.6.2
2.6.3
2.6.4
Schedule Snapshot ......................................................................... 28
Activation Snapshot......................................................................... 28
Priority ............................................................................................. 29
Image FTP ...................................................................................... 29
2.7 Network .................................................................................................................30
2.7.1 Network Setting ............................................................................... 31
2.8 Pan/Tilt/Zoom .......................................................................................................32
2.8.1 PTZ Setup ....................................................................................... 32
2.8.2 PTZ Operation................................................................................. 33
2.8.3 3D Intelligent Positioning Key.......................................................... 33
3
Web Client Operation ....................................................................................................35
3.1 Network Connection ............................................................................................35
3.2 Login ......................................................................................................................35
3.3 Main Window ............................................................................................ 35
3.3.1 LAN Login ....................................................................................... 35
3.3.2 WAN Login ...................................................................................... 36
Appendix Toxic or Hazardous Materials or Elements .....................................................37
ii
Welcome
Thank you for purchasing our DVR!
This quick start guide will help you become familiar with our DVR in a very short time.
Before installation and operation, please read the following safeguard and warning carefully!
Important Safeguard and Warning
1.Electrical safety
All installation and operation here should conform to your local electrical safety codes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
2.Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3.Installation
Keep upwards. Handle with care.
Do not apply power to the DVR before completing installation.
Do not place objects on the DVR.
4.Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5.Environment
The DVR should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included:
Contact your local retailer ASAP if something is missing in your package.
7. Lithium battery
Improper battery use may result in fire, explosion, or personal injury!
When replace the battery, please make sure you are using the same model!
iii
1 Hardware Installation and Connection
Note: All the installation and operations here should conform to your local
electric safety rules.
1.1 Check Unpacked DVR
When you receive the DVR from the forwarding agent, please check whether there is any visible
damage. The protective materials used for the package of the DVR can protect most accidental
clashes during transportation. Then you can open the box to check the accessories.
Please check the items in accordance with the list. (Remote control is optional). Finally you can
remove the protective film of the DVR.
Note
Remote control is not a standard accessory and it is not included in the accessory bag.
1.2 About Front Panel and Rear Panel
For detailed information of the function keys in the front panel and the ports in the rear panel,
please refer to the User’s Manual included in the resource CD.
The model label in the front panel is very important; please check according to your purchase
order.
The label in the rear panel is very important too. Usually we need you to represent the serial
number when we provide the service after sales.
1.3 After Remove the Chassis
Please check the data cable, power cable, COM cable and main boar cable connection is secure
or not.
1.4 HDD Installation
You can refer to the User’s Manual for recommended HDD brand.
Please follow the instructions below to install hard disk.
This series DVR max supports 8 SATA HDDs. Please use HDD of 7200rpm or higher.
1. Loosen the screws of the
2. Remove the HDD upper
3. Now you can see the bottom
upper cover.
bracket
bracket
1
4. Line up the HDD to the
four
holes
of
the
5. Use screws to fix HDD.
HDD
6. Install the upper bracket and then
Use screws to fix HDD in the
bracket.
bracket.
7. Unfasten the HDD power
8. Insert the HDD power
9. Use the special data cable to
cable.
cable.
connect the HDD and the SATA
port. Close the chassis and fix
the screws to secure firmly.
(Note: for the installation steps of HD-SDI series, please take the above steps for reference.)
Important
If the HDD amount is less than four, you do not need to install the HDD bracket.
When there is a bracket, please make sure the installation direction of HDDs is the same.
1.5 Rack Installation
Please note this installation mode is for 1.5U/2U series product.
Please follow the steps listed below.
z Use twelve screws to fix the unit
z Please make sure the indoor temperature is below 35℃ (95°f).
z Please make sure there is 15cm (6 inches) space around the device to guarantee sound
ventilation.
z Please install from the bottom to the top.
z If there are more accessories connected in the rack, please take precaution measures in
case the rack power is overload.
1.6 Front Panel
The front panel is shown as in Figure 1-1.
Figure 1-1
2
The front panel of HD-SDI series and 960H series is shown as follows:
Figure 1-2
Please refer to the following sheet for front panel button information.
Name
Icon
Function
Power button, press this button for three seconds to boot up or
shut down DVR.
Power button
Number button
0-9
Input Arabic number
Switch channel
Input number
more than 10
-/--
If you want to input a number more than 10, please click this
button and then input.
Shift
…
Up/
Down
S、T
In textbox, click this button to switch between numeral,
English(Small/Capitalized),donation and etc.
Enable or disable tour.
Activate current control, modify setup, and then move up and
down.
Increase/decrease numeral.
Assistant function such as PTZ menu.
Shift current activated control, and then move left and right.
Left/
Right
W
ESC
ESC
X
When playback, click these buttons to control playback bar.
Go to previous menu, or cancel current operation.
When playback, click it to restore real-time monitor mode.
Confirm current operation
Enter
ENTER
Go to default button
Go to menu
Record
REC
Slow play
Assistant
Manually stop/start recording, working with direction keys
or numeral keys to select the recording channel.
Multiple slow play speeds or normal playback.
Fn
One-window monitor mode, click this button to display assistant
function: PTZ control and image color.
Backspace function: in numeral control or text control, press it
for 1.5seconds to delete the previous character before the
cursor.
3
In motion detection setup, working with Fn and direction keys to
realize setup.
In text mode, click it to switch between numeral, English
character(small/capitalized) and etc.
In HDD management interface, you can click it to switch HDD
record information and other information (Menu prompt)
Realize other special functions.
Fast play
Play previous
Reverse/Pause
_
W
f
Play Next
Various fast speeds and normal playback.
In playback mode, playback the previous video
In normal playback or pause mode, click this button to reverse
playback
In reverse playback, click this button to pause playback.
In playback mode, playback the next video
In menu setup, go to down ward of the dropdown list.
Play/Pause
f
In normal playback click this button to pause playback
In pause mode, click this button to resume playback.
Window switch
Mult
Click it to switch one-window/multiple-window.
In real-time monitor mode it works as left/right direction key.
Playback mode, counter clockwise to forward and clock wise to
backward.
Up/down direction key.
Playback mode, turn the inner dial to realized frame by frame
playback. (Only applies to some special versions.)
Shuttle(outer
ring)
Jog(inner dial)
USB port
To connect USB storage device, USB mouse.
Remote control
indication light
ACT
Remote control indication light
Status indication
light
Status
If there is Fn indication light, current status indication light is null.
Power indication
light
PWR
Power indication light
Record light
1-32
It becomes on when system is recording.
IR Receiver
IR
It is to receive the signal from the remote control.
4
1.7 Rear Panel
1.7.1 General 2U series
This series DVR rear panel is shown as below. See Figure 1-3.
Figure 1-3
Please refer to the following sheet for detailed information.
1
GND port
2
Power input port
3
Power button
4
Fan
5
DB25 port ( 5th to 16th-channel audio input port)
6
1st to 4th-channel audio input
7
Loop video output
8
Video input
9
Video CVBS output
10
Matrix video output
11
Audio output
12
Bidirectional talk input port
13
Bidirectional talk output port
14
15
16
17
18
19
20
Alarm input/Alarm output/RS485 port
Video VGA output
HDMI port
Video CVBS output RS232 port
Video matrix output eSATA port
USB port
Network port
The 32-channel series DVR rear panel is shown as below. See Figure 1-3.
Figure 1-4
5
Please refer to the following sheet for detailed information.
1
GND port
2
Power input port
3
Power button
4
Fan
5
1st to 4th-channel audio input
6
DB25 port ( 5th to 16th-channel audio input port)
7
Video input
8
Video CVBS output
9
Matrix video output
10
Audio output
11
Bidirectional talk input port
12
Bidirectional talk output port
13
Alarm input/Alarm output/RS485 port
14
15
16
17
18
19
1.7.2
Network port
HDMI port
RS232 port
eSATA port
USB port
Video VGA output
2U series (HD-SDI series)
The rear panel is shown as below. See Figure 1-5.
Figure 1-5
Please refer to the following sheet for detailed information.
1
GND port
2
Power input port
3
Power button
4
Fan
5
Video input
6
Loop video output
7
Audio input
8
Bidirectional talk input port
9
Bidirectional talk output port
10
Video output
11
Audio output
12
Alarm input/Alarm output/RS485 port
13
Network port
14
Video VGA output
6
15
HDMI port
16
USB port
17
eSATA port
18
RS232 port
The rear panel of the 8-channel series product is shown as in Figure 1-6.
Please note there is a series product of only 4-channel audio input.
Figure 1-6
Please refer to the following sheet for detailed information.
1
GND port
2
Audio input
3
Video input
4
Bidirectional talk output port
5
Bidirectional talk input port
6
Audio output
7
Video output
8
Network port
9
Video VGA output
10
HDMI port
11
RS232 port
12
eSATA port
13
USB port
14
1.7.3
Alarm input/Alarm output/RS485 port
2U series (960H series)
The rear panel is shown as below. See Figure 1-7.
Figure 1-7
Please refer to the following sheet for detailed information.
1
GND port
7
2
3
4
5
6
7
8
9
10
11
12
13
Power input port
Power button
Fan
DB25 port (5-16 channel audio input)
1-4channel audio input
Loop video output
Video input
Video CVBS output
Matrix video output
Audio output
Bidirectional talk input port
Bidirectional talk output port
14
15
16
17
18
Alarm input/Alarm output/RS485 port
Video VGA output
HDMI port
RS-232
eSATA port
19
20
USB port
Network port
When connect the Ethernet port, please use crossover cable to connect the PC and use the
straight cable to connect to the switcher or router.
1.8 Connection Sample
1.8.1 2U series
Please refer to Figure 1-8 for connection sample.
The following figure is based on the 16-channel series product.
8
Figure 1-8
1.8.2 2U series (HD-SDI series)
Please refer to the following figure for detailed information. See Figure 1-9.
The following figure is based on the 4-channel series product.
9
Figure 1-9
The 8-channel series product interface is shown as in Figure 1-10.
10
Figure 1-10
1.8.3 2U series (960H series)
Please refer to the following figure for detailed information. See Figure 1-11.
The following figure is based on the 16-channel series product.
11
Figure 1-11
1.9 Alarm Input and Output Connection
Important
Please refer to the specifications for the alarm input and output channel amount. Do not
merely count the alarm input and out channel amount according to the ports on the rear
panel.
There are two alarm input types for you to select: normal open (NO) and normal close (NC).
1.9.1 Alarm Input and Output Details
You can refer to the following sheet for alarm input and output information.
X
Important
Please refer to the specifications for the alarm input and output channel amount. Do not
merely count the alarm input and out channel amount according to the ports on the rear
panel.
1.9.1.1 2U Series
The 2U series product interface is shown as in
Figure 1-12.
12
Figure 1-12
You can refer to the following sheet for alarm input and output information.
ALARM 1 to ALARM 16. The alarm becomes active in low voltage.
1,2,3,4,5,
6,7,8,9,10,
11,12,13,14,
15,16
The first four are four groups of normal open activation output
NO1 C1,
(on/off button)
NO2 C2,
NO5 C5 NC5 is a group of NO/NC activation output (on/off button)
NO3 C3,
NO4 C4,
NO5 C5 NC5
CTRL 12V
+12V
AB cable
connection
Control power output. You need to close the device power to cancel
the alarm.
It is external power input. Need the peripheral equipment to provide
+12V power (below 1A).
Earth cable.
485 A/B
485 communication port. They are used to control devices such as
PTZ. Please parallel connect 120TΩ between A/B cables if there are
too many PTZ decoders.
1.9.1.2 2U Series (HD-SDI series)
The product interface is shown as in Figure 1-13.
Figure 1-13
You can refer to the following sheet for alarm input and output information.
ALARM 1 to ALARM 4. The alarm becomes active in low voltage.
1,2,3,4
NO1 C1,
NO2 C2,
NO3 C3,
NO4 C4,
NO5 C5 NC5
The first four are four groups of normal open activation output
(on/off button)
NO5 C5 NC5 is a group of NO/NC activation output (on/off button)
Earth cable.
T+, T-, R+, R-
RS485 port
485 A/B
485 communication port. They are used to control devices such as
PTZ. Please parallel connect 120TΩ between A/B cables if there are
too many PTZ decoders.
1.9.1.3 2U Series (960H series)
The interface is shown as in Figure 1-14.
13
Figure 1-14
You can refer to the following sheet for alarm input and output information.
1,2,3,4,, 5, 6, 7, ALARM 1 to ALARM 16. The alarm becomes active in low voltage.
8, 9, 10, 11, 12, 13,
14, 15, 16
The first four are four groups of normal open activation output
NO1 C1,
(on/off button)
NO2 C2,
NO5 C5 NC5 is a group of NO/NC activation output (on/off button)
NO3 C3,
NO4 C4,
NO5 C5 NC5
CTRL 12V
+12V
Control power output. You need to close the device power to cancel
the alarm.
It is external power input. Need the peripheral equipment to provide
+12V power (below 1A).
Earth cable.
T+, T-, R+, R-
RS485 port
485 A/B
485 communication port. They are used to control devices such as
PTZ. Please parallel connect 120TΩ between A/B cables if there are
too many PTZ decoders.
1.9.2 Alarm Input Port
Please refer to the following sheet for more information.
z Normal open or Normal close type.
z Please parallel connect COM end and GND end of the alarm detector (Provide external
power to the alarm detector).
z Use the controllable +12V power to reset the smoke sensor remotely.
z Please parallel connect the Ground of the DVR and the ground of the alarm detector.
z Please connect the NC port of the alarm sensor to the DVR alarm input(ALARM)
z Use the same ground with that of DVR if you use external power to the alarm device.
Figure 1-15
1.9.3 Alarm Output Port
z
Provide external power to external alarm device.
14
z
z
z
For controllable +12V, it can be used to provide power to devices such as reset smoke
sensor.
To avoid overloading, please read relay parameters sheet in the User’s Manual carefully.
RS485 A/B cable is for the A/B cable of the PTZ decoder.
15
2 Overview of Navigation and Controls
Before operation, please make sure:
z You have properly installed HDD and all the cable connections.
z The provided input power and the device power are matched.
z The external power shall be AC90~264V 50+2% Hz.
z Always use the stable current, if necessary UPS is a best alternative measure.
2.1 Login, Logout & Main Menu
2.1.1 Login
After system booted up, system pops up the startup wizard.
Click the Cancel button; you can go to the system login interface.
Click the Next Step button; you can go to the startup wizard interface. Here you can set the
system basic information. See Figure 2-1.
Figure 2-1
The system login interface is shown as in Figure 2-2.
System consists of four accounts:
z
z
z
Username: admin. Password: admin. (administrator, local and network)
Username: 888888. Password: 888888. (administrator, local only)
Username: 666666. Passwords: 666666(Lower authority user who can only monitor, playback,
backup and etc.)
z Username: default. Password: default(hidden user)
You can use USB mouse, front panel, remote control (not included in the accessory bag) or
keyboard to input. About input method: Click
to switch between numeral, English character
(small/capitalized) and denotation.
Note:
For security reason, please modify password after you first login.
Within 30 minutes, three times login failure will result in system alarm and six times login failure
will result in account lock!
16
Figure 2-2
2.1.2
Main Menu
After you logged in, the system main menu is shown as below. See Figure 2-3.
There are total six icons: search, information, setting, backup, advanced and shutdown.
You can move the cursor to highlight the icon, and then double click mouse to enter the submenu.
Figure 2-3
2.1.3
Logout
There are two ways for you to log out.
The first one is from menu option:
In the main menu, click shutdown button, you can see an interface is shown as below. See
Figure 2-4.
Figure 2-4
There are several options for you. See Figure 2-5.
Figure 2-5
The other ways is to press power button on the front panel for at least 3 seconds, system will
stop all operations. Then you can click the power button in the front panel to turn off the DVR.
17
Please note, before you replace the HDD, do remember shutting down the device and unplug the
power cable.
2.1.4
Auto Resume after Power Failure
The system can automatically backup video and resume previous working status after power
failure.
2.2 Live Viewing
After you logged in, the system is in live viewing mode by default. You can see system date, time
and channel name. If you want to change system date and time, you can refer to general settings
(Main Menu->Setting->General). If you want to modify the channel name, please refer to the
display settings (Main Menu->Setting->Display)
1
Recording status
3
Video loss
2
Motion detection
4
Camera lock
Preview Control
The preview control function has the following features.
z Support preview playback.
— In the preview desktop, system can playback previous 5-60 minutes record of
current channel. Please go to the Main Menu->General to set real-time playback
time.
— Support drag and play function. You can use your mouse to select any playback
start time.
— Support playback, pause and exit function.
— Right now, system does not support slow playback and backward playback function.
z Support digital zoom function.
z Support real-time backup function.
You can follow the contents listed below for the operation instruction.
Preview control interface
Move you mouse to the top centre of the video of current channel, you can see system pops
up the preview control interface. See Figure 2-6. If your mouse stays in this area for more
than 6 seconds and has no operation, the control bar automatically hides.
1
2
3
4
Figure 2-6
You can refer to the following sheet for detailed information.
SN
Name
Function
1
Realtime playback
It is to playback the previous 5-60 minutes
record of current channel.
Please go to the Main Menu->General to set
real-time playback time.
System may pop up a dialogue box if there is no
such record in current channel.
2
Digital zoom
It is to zoom in specified zone of current
channel. It supports zoom in function of multiplechannel.
18
The selected area has an icon as
3
Real-time
function
backup
and the
free area is shown as an icon as
.
It is to backup the video of current channel to
the USB device. System can not backup the
video of multiple-channel at the same time.
Current selected backup channel has an icon as
and the free channel is shown as an icon as
. .
Once the backup started, you can see the free
channel is shown as an icon as
.
4
Exit
Playback control
The playback control has the following features.
z Support play, pause, and exit and drag function.
z During the preview playback process, you can not see the channel title and record status
of current channel. It will display the channel title and the record status once you exit the
preview playback.
z During the preview playback, you can not switch the displayed channel or change
current window-display mode.
z Please note, the tour function has the higher priority than the preview playback. System
automatically exits the preview playback function and its corresponding interface when
the tour function started. You can not control the preview playback until the tour function
ended.
2.3 Manual Record
Note:
You need to have proper rights to implement the following operations. Please make sure the
HDD has been properly installed.
2.3.1 Manual record menu
There are two ways for you to go to manual record menu.
z Right click mouse or in the main menu, Advanced->Manual Record.
z In live viewing mode, click record button in the front panel or record button in the remote
control.
Manual record menu is shown as in Figure 2-7.
2.3.2 Basic operation
There are three statuses: schedule/manual/stop. Please highlight icon“○” to select
corresponding channel.
z Manual: The highest priority. After manual setup, all selected channels will begin ordinary
recording.
z Schedule: Channel records as you have set in recording setup (Main Menu->Setting>Schedule)
z Stop: All channels stop recording.
19
Figure 2-7
2.3.3 Enable/disable record
Please check current channel status: “○” means it is not in recording status, “●” means it is in
recording status.
You can use mouse or direction key to highlight channel number. See Figure 2-8.
Figure 2-8
2.3.4 Enable all channel recording
Highlight ○ below All, you can enable all channel recording.
z All channel schedule record
Please highlight “ALL” after “Schedule”. See Figure 2-9.
When system is in schedule recording, all channels will record as you have previously set
(Main menu->Setting->Schedule).
The corresponding indication light in front panel will turn on.
20
Figure 2-9
z All channel manual record
Please highlight “ALL” after “Manual.” See Figure 2-10.
When system is in manual recording, all scheduled set up you have set in will be null ((Main
menu->Setting->Schedule)).
You can see indication light in front panel turns on, system begins manual record now.
Figure 2-10
2.3.5 Stop all channel recording
Please highlight “ALL” after “Stop”. See Figure 2-11.
System stops all channel recording no matter what mode you have set in the menu (Main
menu->Setting->Schedule)
Figure 2-11
21
2.4 Search & Playback
Click search button in the main menu, search interface is shown as below. See Figure 2-12.
Usually there are three file types:
z R: Regular recording file.
z A: External alarm recording file.
z M: Motion detection recording file.
2
1
3
4
11
7
8
12
6
5
10
9
Figure 2-12
Please refer to the following sheet for more information.
SN
1
2
Name
Display
window
Function
zHere is to display the searched picture or file.
zSupport 1/4/9/16-window playback.
Search
type
zHere you can select to search the picture or the recorded file.
zYou can select to play from the read-write HDD or the connected external
device.
3
Calendar
4
Playback
mode
and
channel
selection
pane.
zThe blue highlighted date means there is picture or file. Otherwise, there is no
picture or file.
zIn any play mode, click the date you want to see, you can see the corresponding
record file trace in the time bar.
zPlayback mode:1/4/9/16. (It may vary due to different series.)
— In 1-window playback mode: you can select 1-16 channels.
— In 4-window playback mode: you can select 4 channels according to your
requirement.
— In 9-window playback mode, you can switch between 1-9 and 10-16 channels.
— In 16-window playback mode, you can switch between1-16 and 17-32
channels.
22
zThe time bar will change once you modify the playback mode or the channel
option.
zDouble click it, you can view the picture/record file list of current day.
zThe file list is to display the first channel of the record file.
zThe system can display max 128 files in one time. Use the S/T or the mouse to
view the file. Select one item, and then double click the mouse or click the ENTER
button to playback.
zYou can input the period in the following interface to begin accurate search.
zFile type:R—regular record; A—external alarm record;M—Motion detect
record.
5
File list
switch
button
6
Card
number
search
7
Playback
control
pane.
zLock file. Click the file you want to lock and click the button
to lock. The file
you locked will not be overwritten.
zSearch locked file: Click the button
to view the locked file.
zReturn: Click button
, system goes back to the calendar and channel setup
interface.
Please note:
zSystem max locks 16 files. The size of the locked file shall be less than the 1/4 of
the HDD total space. The first 16G of each partition can not be locked.
zSystem can only lock one file at one time and can not lock the extra stream. For
the file that is writing or overwriting, it can not be locked.
The card number search interface is shown as below. Here you can view card
number/field setup bar. You cam implement advanced search.
►/
■
W
│W/
X│
►
Play/Pause
There are three ways for you to begin playback.
z The play button
z Double click the valid period of the time bar.
z Double click the item in the file list.
In slow play mode, click it to switch between play/pause.
Stop
Backward play
In normal play mode, left click the button, the file begins backward play.
Click it again to pause current play.
In backward play mode, click ►/ to restore normal play.
In playback mode, click it to play the next or the previous section. You can
click continuously when you are watching the files from the same channel.
In normal play mode, when you pause current play, you can click W│ and
│X to begin frame by frame playback.
In frame by frame playback mode, click ►/ to restore normal playback.
Slow play
In playback mode, click it to realize various slow play modes such as slow
play 1, slow play 2, and etc.
Fast forward
In playback mode, click to realize various fast play modes such as fast
play 1,fast play 2 and etc.
Note: The actual play speed has relationship with the software version.
Smart search
The volume of the playback
23
8
Time bar
9
Time bar
unit
10
Backup
11
Clip
12
Record
type
Click the snapshot button in the full-screen mode, the system can snapshot
1 picture per second.
zIt is to display the record type and its period in current search criteria.
zIn 4-window playback mode, there are corresponding four time bars. In other
playback mode, there is only one time bar.
zUse the mouse to click one point of the color zone in the time bar, system begins
playback.
zThe time bar is beginning with 0 o'clock when you are setting the configuration.
The time bar zooms in the period of the current playback time when you are
playing the file.
zThe green color stands for the regular record file. The red color stands for the
external alarm record file. The yellow stands for the motion detect record file.
●The option includes: 24H, 12H, 1H and 30M. The smaller the unit, the larger the
zoom rate. You can accurately set the time in the time bar to playback the record.
zThe time bar is beginning with 0 o'clock when you are setting the configuration.
The time bar zooms in the period of the current playback time when you are
playing the file.
Select the file(s) you want to backup from the file list. System max supports files
from four channels. Then click the backup button, now you can see the backup
menu. Click the start button to begin the backup operation.
Check the file again you can cancel current selection.
System max supports to display 32 files from one channel.
zIt is to edit the file.
●Please play the file you want to edit and then click this button when you want to
edit. You can see the corresponding slide bar in the time bar of the corresponding
channel. You can adjust the slide bar or input the accurate time to set the file end
time. Click this button again and then save current contents in a new file. .
In any play mode, the time bar will change once you modify the search type.
button, system begins smart search. System supports 396(22*18
Click the
PAL) and 330(22*15 NTSC) zones. See Figure 2-13.
13
Smart
search
Figure 2-13
Click the
, you can go to the smart search playback. Click it again, system stops
smart search playback.
Please note:
z When system is playing, you can select a zone in the window to begin motion
detect. Click the motion detect button to begin play.
z Once the motion detect play has begun, click button again will terminate
current motion detect file play.
24
The system will take the whole play zone as the motion detect region by
default.
z If you select to play other file in the file list, system switches to motion detect
play pf other file.
z During the motion detect play process, you can not implement operations such
as change time bar, begin backward playback or frame by frame playback. .
Important
System does not support motion detect zone setup during the full-screen
mode.
z
14
Other channel
synchronization switch to
play when playback
15
Digital zoom
Other Functions
When playing the file, click the number button, system can
switch to the same period of the corresponding channel to
play.
When the system is in full-screen playback mode, left click
the mouse in the screen. Drag your mouse in the screen to
select a section and then left click mouse to realize digital
zoom. You can right click mouse to exit.
2.5 Schedule
Note:
You need to have proper rights to implement the following operations. Please make sure the
HDDs have been properly installed.
After the system booted up, it is in default 24-hour regular mode. You can set record type and
time in schedule interface.
In the main menu, from Setting to Schedule, you can go to schedule menu. See Figure 2-14.
There are total six periods.
z Channel: Please select the channel number first. You can select “all” if you want to set for
the whole channels.
z Week day: There are eight options: ranges from Saturday to Sunday and all.
z Pre-record: System can pre-record the video before the event occurs into the file. The value
ranges from 1 to 30 seconds depending on the bit stream.
z Redundancy: System supports redundancy backup function. You can highlight Redundancy
button to activate this function. Please note, before enable this function, please set at least
z
z
z
one HDD as redundant. (Main menu->Advanced->HDD Management). Please note this
function is null if there is only one HDD.
Snapshoot: You can enable this function to snapshoot image when alarm occurs.
Record types: There are four types: regular, motion detection (MD), Alarm, MD & alarm.
Holiday setting: Click it you can see an interface shown as in Figure 2-15. Here you can set
holiday date. Check the box, it means current channel shall record as your holiday setup.
Please go to the Period interface to set the holiday date record setup.
Please highlight icon
to select the corresponding function. After completing all the setups
please click save button, system goes back to the previous menu.
At the bottom of the menu, there are color bars for your reference. Green color stands for
regular recording, yellow color stands for motion detection and red color stands for alarm
recording. The white means the MD and alarm record is valid. Once you have set to record
25
when the MD and alarm occurs, system will not record neither motion detect occurs nor the
alarm occurs.
Figure 2-14
Figure 2-15
2.5.1 Quick Setup
Copy function allows you to copy one channel setup to another. After setting in channel 1, click
Copy button, you can go to interface Figure 2-16. You can see current channel name is grey
such as channel 1. Now you can select the channel you wan to paste such as channel 5/6/7. If
you wan to save current setup of channel 1 to all channels, you can click the first box “ALL”. Click
the OK button to save current copy setup. Click the OK button in the Encode interface, the copy
function succeeded.
Please note, if you select ALL in Figure 2-16, the record setup of all channels are the same and
the Copy button becomes hidden.
26
Figure 2-16
2.5.2 Redundancy
Redundancy function allows you to memorize record file in several disks. When there is file
damage occurred in one disk, there is a spare one in the other disk. You can use this
function to maintain data reliability and safety.
In the main menu, from Setting to Schedule, you can highlight redundancy button to enable
this function. See Figure 2-17.
In the main menu, from Advanced to HDD management, you can set one or more disk(s) as
redundant. You can select from the dropdown list. See Figure 2-17. System auto overwrites
old files once hard disk is full.
Please note only read/write disk or read-only disk can backup file and support file search
function, so you need to set at least one read-write disk otherwise you can not record video.
Note
About redundancy setup:
z If current channel is not recording, current setup gets activated when the channel begin
recording the next time.
z If current channel is recording now, current setup will get activated right away, the current file
will be packet and form a file, then system begins recording as you have just set.
After all the setups please click save button, system goes back to the previous menu.
Figure 2-17
Playback or search in the redundant disk.
There are two ways for you to playback or search in the redundant disk.
27
z
z
Set redundant disk(s) as read-only disk or read-write disk (Main menu->Advanced->HDD
management). See Figure 2-17.System needs to reboot to get setup activated. Now you can
search or playback file in redundant disk.
Dismantle the disk and play it in another PC.
2.6 Snapshot
2.6.1 Schedule Snapshot
In Encode interface, click snapshot button to input snapshot mode, size, quality and
frequency. See the interface on the left of Figure 2-18.
Note:
The HD-SDI series product supports 1080P, 720P, D1, HD1, 2CIF, CIF, QCIF resolution.
The 960H supports 960H, D1, HD1, 2CIF, CIF, QCIF resolution.
In FTP (Main Menu->Network->Network Setting) interface, please input upload interval. See
the interface in the middle of Figure 2-18.
In Schedule interface, please enable snapshot function. See interface on the right of Figure
2-18.
Please refer to the following figure for detailed information. See Figure 2-18.
Figure 2-18
2.6.2 Activation Snapshot
Please follow the steps listed below to enable the activation snapshot function. After you
enabled this function, system can snapshot when the corresponding alarm occurred.
28
In Encode interface, click snapshot button to input snapshot mode, size, quality and
frequency. See the interface on the left of Figure 2-19.
z In FTP interface please input upload interval. See the interface in the middle of Figure
2-18.
z In Detect interface please enable snapshot function for specified channels (interface in
the middle of Figure 2-19). Or in alarm interface (interface on the right of Figure 2-19)
please enable snapshot function for specified channels.
Please refer to the following figure for detailed information. See Figure 2-19.
z
Figure 2-19
2.6.3 Priority
Please note the activation snapshot has the higher priority than schedule snapshot. If you
have enabled these two types at the same time, system can activate the activation snapshot
when alarm occurs, and otherwise system just operates the schedule snapshot.
2.6.4 Image FTP
In Network interface, you can set FTP server information. Please enable FTP function and
then click save button. See Figure 2-20.
Please boot up corresponding FTP server.
Please enable schedule snapshot (Chapter 2.5) or activation snapshot (Chapter 2.6.2) first,
now system can upload the image file to the FTP server.
29
Please input the
corresponding information
here, if you just upload the
image FTP.
Figure 2-20
2.7 Network
Here is for you to input network information.
z IP Version: There are two options: IPv4 (Figure 2-21) and IPv6 (Figure 2-22). Right now, system
supports these two IP address format and you can access via them.
z MAC address: The host in the LAN can get a unique MAC address. It is for you to access in the
LAN. It is read-only.
z
z
z
z
z
z
z
z
IP address: Here you can use up/down button (ST) or input the corresponding number to
input IP address. Then you can set the corresponding subnet mask the default gateway.
Subnet prefix: The input value ranges from 0 to 128. It is to mark a specified network MAC
address. Usually it includes an organization of multiple-level.
Default gateway: Here you can input the default gateway. Please note system needs to
check the validity of all IPv6 addresses. The IP address and the default gateway shall
be in the same IP section. That is to say, the specified length of the subnet prefix shall
have the same string.
DHCP: It is to auto search IP. When enable DHCP function, you can not modify IP/Subnet
mask /Gateway. These values are from DHCP function. If you have not enabled DHCP
function, IP/Subnet mask/Gateway display as zero. You need to disable DHCP function to
view current IP information. Besides, when PPPoE is operating, you can not modify
IP/Subnet mask /Gateway.
TCP port: Default value is 37777. You can change if necessary.
UDP port: Default value is 37778. You can change if necessary.
HTTP port: Default value is 80.
RTSP port: Default value is 554.
Important: System needs to reboot after you changed and saved any setup of the above
four ports. Please make sure the port values here do not conflict.
z Max connection: system support maximal 20 users. 0 means there is no connection limit.
z Preferred DNS server: DNS server IP address.
z Alternate DNS server: DNS server alternate address.
z Transfer mode: Here you can select the priority between fluency/video qualities.
z LAN download: System can process the downloaded data first if you enable this function.
The download speed is 1.5X or 2.0X of the normal speed.
30
Important
For the IP address of IPv6 version, default gateway, preferred DNS and alternate DNS, the
input value shall be 128-digit. It shall not be left in blank.
After completing all the setups please click save button, system goes back to the previous menu.
Figure 2-21
Subnet Prefix
Figure 2-22
2.7.1 Network Setting
Network setting interface is shown as in Figure 2-23. Please check the box to enable
corresponding function and then double click current item to go to setup interface.
31
Figure 2-23
2.8 Pan/Tilt/Zoom
Please note:
z Slight difference may be found in the user’s interface, due to various protocols.
z Please make sure the speed domes A/B cables are properly connected to the A/B ports of
DVR.
z You have properly set PTZ information.
z Please switch camera monitor channel to current window.
2.8.1 PTZ Setup
The pan/tilt/zoom setup includes the following items. Please select channel first. See Figure 2-24.
z Protocol: Select corresponding PTZ protocol such as PELCOD.
z Address: Input corresponding PTZ address.
z Baud rate: Select baud rate.
z Data bit: Select data bit. Default value is 8.
z Stop bit: Select stop bit. Default value is 1.
z Parity: There are three choices: none/odd/even. Default value is none.
Figure 2-24
32
After completing all the setups please click save button, system goes back to the previous menu.
2.8.2 PTZ Operation
In one window display mode, right click mouse (click “Fn” Button in the front panel or click
“Fn” key in the remote control). The interface is shown as in Figure 2-25.
Figure 2-25
Click Pan/Tilt/Zoom, the interface is shown as below. See Figure 2-26.
Here you can set the following items:
z Step: value ranges from 1 to 8.
z Zoom
z Focus
z Iris
Click icon
and
to adjust zoom, focus and iris.
Figure 2-26
In Figure 2-26, please click direction arrows (See Figure 2-27) to adjust PTZ position. There are
total 8 direction arrows. Please note if you use remote control, you can use just four directions
(Up/down/left/right).
The speed value ranges from 1 to 8.
Figure 2-27
2.8.3 3D Intelligent Positioning Key
In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See Figure
2-28. Please note, this function needs protocol supported and can only be operated by mouse.
33
Click this key, system goes back to the single screen mode. Drag the mouse in the screen to
adjust section size. It can realize PTZ automatically.
Figure 2-28
Here is a sheet for you reference.
Name
Function
function
key
Zoom
Near
Focus
Near
Iris
close
Shortcut
key
►
_
W
Function
key
function
Far
Far
Open
Shortcut
Key
►
f
You can click set button in Figure 2-26 (or click REC button in the front panel) to set preset, tour,
and pattern.
You can click page switch button in Figure 2-26 (or click Fn button in the front panel) to call main
function.
34
3 Web Client Operation
Slightly difference may be found in the interface due to different series.
3.1 Network Connection
Before web client operation, please check the following items:
z Network connection is right
z DVR and PC network setup is right. Please refer to network setup(main menu->setting>network)
z Use order ping ***.***.***.***(* DVR IP address) to check connection is OK or not. Usually
the return TTL value should be less than 255.
z System can automatically download latest web control and the new version can overwrite
the previous one.
z If you want to un-install the web controls, please run uninstall webrec2.0.bat to auto delete
the control or you can go to C:\Program Files\webrec to delete Single folder.
z Current series product supports various browsers such as Safari, firebox browser, Google
browser. Device only support 1-channel monitor on the Apple PC.
3.2 Login
Open IE and input DVR address in the address column. For example, if your DVR IP is
10.10.3.16, then please input http:// 10.10.3.16 in IE address column.
System pops up warning information to ask you whether install webrec.cab control or not. Please
click yes button.
If you can’t download the ActiveX file, please modify your IE security setup.
After installation, the interface is shown as below. See Figure 3-1.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Figure 3-1
3.3 Main Window
3.3.1 LAN Login
For the LAN mode, after you logged in, you can see the main window. See Figure 3-2.
35
Click the channel name on the left side; you can view the real-time video.
Figure 3-2
3.3.2 WAN Login
In WAN mode, after you logged in, the interface is shown as below. See Figure 3-3.
Figure 3-3
For detailed operation information, please refer to the User’s Manual included in the resources
CD.
36
Appendix Toxic or Hazardous Materials or Elements
Component
Name
Toxic or Hazardous Materials or Elements
Pb
Hg
Cd
Cr VI
PBB
PBDE
○
○
○
○
○
○
○
○
○
○
○
○
Circuit Board
○
○
○
○
○
○
Fastener
Wire and
Cable/AC
Adapter
Packing
Material
Accessories
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Sheet
Metal(Case)
Plastic Parts
(Panel)
Note
O: Indicates that the concentration of the hazardous substance in all homogeneous materials in
the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury or
damage to any assets. The consumer is not authorized to process such kind of substances or
elements, please return to the corresponding local authorities to process according to your local
government statutes
Note
z For detailed operation introduction, please refer to our resource CD included in your
package for electronic version of the User’s Manual.
z Slight difference may be found in user interface.
z All the designs and software here are subject to change without prior written notice.
z
z
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website for more information.
37
Download PDF