GV-LPR CAM 20A Installation Guide V2.0 (Type B Model)

Models
The GV-LPR CAM is available in both EIA and CCIR video format. The camera gives a 570
TVL high-contrast license plate recognition video to the GV-LPR software that identifies license
plates. It features 24 high-efficient LEDs for an illumination range of 15 ~ 25 meters / 49.21 ~
82.02 feet. It also features a weather-sealed, IP66-compliant housing with the heater and
blower inside. This installation guide will take you through the functionality and use of the
GV-LPR CAM.
Note:
The GV-LPR CAM comes with a free GV-LPR Software, and you need to insert the supplied
GV-USB Dongle to the PC to run the software. The free GV-LPR Software is a Trial Edition.
It can only capture the license plate images and does not support the license plate
recognition function.
Packing List
GV-LPR CAM 20A
Installation Guide V2.0
(Type B Model)
●
AC Power Cable (110-125V, 10A) x 1
●
Power Adapter (100-240V, 12V/5A) x 1
●
Outdoor Mounting Bracket x 1
●
GV-LPR Software DVD
●
GV-USB Dongle
There are hardware types A, B and C for GV-LPR CAM 20A. Your current device is a type B.
You can find this information on your product box.
GV-LPR CAM 10A PAL DC12V
GV-LPR CAM 10A NTSC DC12V
GV-LPR CAM 20A PAL DC12V
GV-LPR CAM 20A NTSC DC12V
A
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
© 2012 Auguest GeoVision Inc. All rights reserved.
2012/08
English
LPRCAM20AV20-C
B
C
Installing Camera Module
1. Push the sun shield forward to align with
the back of camera enclosure.
4. Slightly lift the camera module and slide it
out completely.
6. Insert the video cable through the screw
cap.
9.
Loosen the screw cap on the right, insert
the power cable through the screw cap.
Sun Shield
Screw Cap
Camera Enclosure Back
7. Attach the video cable to the BNC
connector and plug it into the “VIDEO
OUT” jack.
2. Loosen the set screws on the back of the
camera enclosure.
VIDEO OUT
Jack
Completely slide the camera
module out
5. Loosen the screw cap on the left.
10. Remove the terminal block. Plug black
and white wires of the power cable to the
terminal block. Reinsert the terminal
block onto the camera. The white wire is
required to connect to the positive pin (+)
on the camera and the black wire to the
negative pin (-).
8. Adjust the length of the video cable and
then tightly screw the cap.
3. Pull out the camera module.
Camera Module
11. Adjust the length of the cable and then
tightly screw the cap (see Steps 8 for the
picture).
Adjusting Camera Settings
Overview
9
8
Shutter Speed
See the lists below for shutter speed settings.
7
Distance between the object and the
camera is 550 cm (18.04 ft).
1
2
No
6
165 SEC
145 SEC
5
182 SEC
150 SEC
4
183 (*) SEC
155 SEC
184 SEC
170 SEC
185 SEC
180 SEC
225 SEC
200 SEC
3
Function
1
Auto Iris lens connector
2
Video out
3
Power Terminal (It is already connected. Follow Steps 11 to 12 in Installing Camera
Module to insert the Power Cable.)
4
Moves down the OSD menu.
5
Moves the focus rightward to select menu options.
6
Power LED
7
Moves up the OSD menu.
8
Enters the OSD menu option and confirms the selection
9
Moves the focus leftward to select menu options.
Distance between the object and the
camera is 1100 cm (36.08 ft).
Note:
1. The default settings are marked with (*).
2. The gray areas in the charts are not recommended for use.
LED Brightness Settings
The GV-LPR CAM is designed with 24 high-efficient LEDs which you can adjust the brightness.
You can push up (ON) and down (OFF) the switches of SW2, SW3 and SW4 for LED
brightness settings. See the table below for 8 LED brightness setting values.
Note: The factory default setting of SW1 is ON. If you find the images of license plates captured
in the day time or sufficient lights are unclear, check the SW1 and make sure it is switched to
ON.
SW4
LED Brightness (mA)
ON
ON
470 (Default Setting)
ON
OFF
400
ON
OFF
ON
350
4
ON
OFF
OFF
300
5
OFF
ON
ON
250
6
OFF
ON
OFF
200
7
OFF
OFF
ON
150
8
OFF
OFF
OFF
100
SW2
SW3
1
ON
2
ON
3
OSD Menu Options and Functions
Main Menu
Sub Menu
Options
Function
Default
Main Menu
Sub Menu
Options
Function
Exposure
Lens
Manual (ELC Level)
Manually adjusts the camera lens.
-
Day & Night
Auto
ON, OFF
Automatically switches between color and B & W
DC (DC Level)
Press SET to adjust the lens
17
Color ► BW 0 ~ 214
brightness.
E. Shutter
1/60, 1/100FLC,
Burst
BW ► Color 0 ~ 214
Sets the shutter speed for the camera. 1/500
Read time
1/120, 1/250, 1/500,
3 ~ 12
1/1000, 1/2000,
The backlight compensation (BLC)
OFF
which the camera changes from
black-and- white to color.
appear clearly when they have strong
backlighting. Select ON and press SET
● Read time: The time taken for the
LEVEL to adjust the BLC ratio at the
camera to change from color to
black-and- white mode or the reverse
center, top, down, left and right of the
camera. The higher value, the stronger
the compensation.
OFF, 12 DB, 15 DB,
Automatically adjusts the camera light
33 DB
Function
WB Mode
Color
n/a
Sets the scene in colors.
B&W
n/a
Sets the scene in black and white.
Mirror
ON, OFF
Select ON to reverse the image.
OFF
18 DB, 21 DB, 24
sensor to accommodate for different
DB, 27 DB, 30 DB,
illumination level and produce clear
Sharpness
0 ~ 49
Adjusts the sharpness value.
20
33 DB, 36 DB
image. The higher the value, the
Gamma
User, 0.45,
Adjusts the gamma value.
0.45
ON (0 ~ 50),
Enable and configure the Side Light
OFF
OFF
Compensation (SLC) to compensate
brighter the image.
RGB
AWC
0.6, 1.0
Automatically adjusts the white balance AWC
SLC
under fixed level of illumination.
ATW
Dynamically adjusts the color intensity
scenes with brighter center and darker
surroundings.
according to illumination level of the
scene.
Manual
Not functional
Pushlock
Select this option to apply the current
HME
ON (0 ~ 50),
Enable and configure the Highlight
OFF
Masking Exposure (HME) to mask areas
later.
R- Y Gain
Not functional
B- Y Gain
Not functional
Mask 1
ON, OFF
Mask 3
Mask 4
Color Set
BLACK, GRAY,
Color1 ~ Color6
ON, OFF
OFF
Enable the Dynamic Range Compressor
OFF
(DRC) to reduce the illumination
difference within a scene.
128
Exit
n/a
Press ENTER to exit the OSD menu.
Select ON to enable the mask and
Save & Exit
n/a
Press ENTER to save configurations and -
select SET WINDOW to define the size
of the privacy mask.
Factory Set
n/a
view to keep sensitive areas invisible.
Mask 2
DRC
128
Sets up to 4 solid blocks on the live
OFF
of strong illumination and compensates
low-light areas within a scene.
white balance settings to all the scenes
Privacy
monitor only displays in colors.
● BW ► Color: The threshold value at
processes the scene for objects to
AGC
● Burst: Enable this function if your LCD
which the camera changes from color to
black-and-white.
1/100000
ON, OFF
black-and-white mode based on the
illumination conditions.
● Color ► BW: The threshold value at
1/4000, 1/10000,
BLC
Default
Sets the color of the privacy mask.
Exit
-
exit the OSD menu.
BLACK
Press ENTER to load factory default
settings.
-
Installing Camera Enclosure
Main Menu
Sub Menu
Options
Function
Default
Set
Camera ID
0 ~ 254
Names the came ra.
1
Title
n/a
Sets a title.
-
Reset
n/a
Edits the title.
Position
Top-L, Top-R, Sets the position of the title.
Bot-L, Bot-R
TOP-L
DPC
White Thr
0 ~ 254
Reduces the defective white pixels.
50
Set
Black Thr
0 ~ 254
Reduces the defective black pixels.
100
DPC Level
0 ~ 254
Sets the area of effect pixels used to
50
Edit
After the installation of camera module and settings adjustment, you are now ready to install the
camera enclosure back.
1. Adjust the lens focus.
2. Lift the camera module.
3. Align the camera module to the camera
4. Secure the camera enclosure with the
-
compensate for the defective ones.
Motion
Langu Chinese
age
English
n/a
Sets the language of the OSD menu.
English
PC Cont.
ON, OFF
Not functional
ON
Alarm Set window
n/a
Sets the detection zone in blocks. Use the Full-scre
n/a
(ON)
direction buttons and the ENTER button
to configure.
en
detectio
n zone
All set
n/a
Sets the full scene as the detection zone. -
All clear
n/a
Clears the previously set detection zone.
-
Sensiti.
0 ~ 55
Adjusts the alarm sensitivity.
44
Show Indi
OFF, ICON,
Sets the type of alarm indicator.
OFF
TRACE
● ICON: shows an icon at the top left
corner when motion is detected
anywhere in the detection zone.
● TRACE: shows color blocks where
motion is detected.
Delay out
1, 3, 5, 7, 9,
Sets the time taken for the alarm
13, 15
message to show after a motion is
detected.
enclosure and slide it back.
1
Note:
The factory default GAMMA value is set to be 1. It will be adjusted to 0.45 every time when you select
RESET. For optimal image performance, it is recommended to adjust the GAMMA value to 1.
5. Push the sun shield back.
screws on both sides.
Specifications
GV-LPR CAM 20A 1/3’’ B/W License Plate Recognition Camera
Model
GV-LPR CAM 20A EIA DC 12V
GV-LPR CAM 20A CCIR DC 12V
Camera
Max. Power Consumption
30W (normal), 50W (heater on)
Dimensions (L x W x H)
425.01 x 155 x 156.75 mm / 16.73 x 6.10 x 6.17 in (with sun shield)
Weight
5 kg / 11.02 lb (with sun shield)
Image Sensor
1/3" B/W EXview CCD
Construction
Robust aluminum with weatherproof sun shield
Resolution
570 TVL
Regulatory
CE, FCC, C-Tick
Protection classification
IP66
EIA
Video Standard
Min. Illumination
Color
N/A
B/W
N/A
IR ON
0 Lux
CCIR
Shutter Speed
Automatic, Fixed (1/60 ~ 1/100000; Deault 1/500)
White Balance
AWB
Image Setting
Brightness, Contrast, Saturation, Sharpness, Gamma, White Balance,
Note:
All specifications are subject to change without notice.
Flicker-less, Image Orientation, Shutter Speed
IR LAMP
LED Quantity
24 high-efficient LEDs
IR Distance
18 m / 59.06 ft (optimal)
15 ~ 25 m / 49.21 ~ 82.02 ft
25,000 hrs
Illuminator Life
Lens
Focal Length
10 ~ 120 mm
Max. Aperture
1.6
Mount
CS Mount
Image Format
1/3"
Operation
Focus
manual
Zoom
manual
Iris
DC
Mechanical
N/A
Lens Mounting
Connectors
Power
DC Jack
Auto Iris DC drive
TV-Out
BNC
General
Operating Temperature
Operation: -30 °C ~ 50 °C / -22 °F ~ 122 °F
Storage: -30 °C ~ 70 °C / -22 °F ~ 158 °F
Heater
≤ 5 °C (ON), > 5 °C (OFF) ; 20W
Power Source
12V DC
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
sales@geovision.com.tw
http://www.geovision.com.tw
Download PDF