GNSS Receiver Quick Tour with GNSSTool

CHC® GNSS Receiver
QuickTour with GNSSTool
(PDA Network Mode)
1. Launch the GNSSTool software and Click
[Connect] menu to connect receiver.
2.
In connect interface, users will config
device protocol and connection type.
3. Device Protocol: Including the choices of
Smart RTK (like i80), GNSS RTK (like X91),
Local (the device to use GNSSTool, like
HCE300 or Android phone) and Peripheral
(like X360).
4. Connection Type: If receiver is smart RTK
(like i80), there are there choices: Bluetooth,
WiFi and Demonstration. If receiver is GNSS
RTK (like X91), there are two choices:
Bluetooth, and Demonstration.
(1) If users choose WiFi, then users will click
Connection Hot Spot to search available
GNSS Receiver Quick Tour with GNSSTool (PDA Network Mode)
1
network.
Then it will request users to open WLAN
Setting, please choose the WiFi of receiver
(like GNSS-1002521) and input password
(12345678).
It will prompt Connected if you connect
successfully,
also
it
will
display
WiFiConnected in the main interface.
(2) If users choose Bluetooth, then users will
click Target bt to search available Bluetooth.
Then click CONNECT to connect receiver.
GNSS Receiver Quick Tour with GNSSTool (PDA Network Mode)
2
Then it will request users to open Bluetooth
Setting, please choose the Bluetooth of
receiver (like GNSS-1002521) and pair with it.
It will prompt Connected if you connect
successfully,
also
it
will
display
BlueToothConnected in the main interface.
Then click CONNECT to connect receiver.
(3) If users choose Demonstration, then users
will use or test all the functions of this
software. Just click CONNECT to finish.
GNSS Receiver Quick Tour with GNSSTool (PDA Network Mode)
3
It will prompt Connected if you connect
successfully,
also
it
will
display
DemostrationConnected
in
the
main
interface.
6. Click [Work Mode] menu to config work
mode.
7.
Main screen of work mode displays the
configuration of the current equipment. In most
5. Click [Receiver Setting] menu to config
receiver.
cases, we use the common and specific
operation mode to meet the daily trial.
GNSS Receiver Quick Tour with GNSSTool (PDA Network Mode)
4
: Click to create a new work mode.
8. Then it will prompt Create New Work
Mode interface.
to obtain APN information, and click
to confirm.
Click
10.
Source List: Click to obtain source table
and select message source.
RTK: Switch on.
Work Way: Select Auto Rover.
DataLink: Select Network.
Diff Source Type: Select CORS.
Input the corresponding IP and Port.
9. Users will also click APN to get SIM APN.
GNSS Receiver Quick Tour with GNSSTool (PDA Network Mode)
5
shielding obstruction. The satellites lower than
this angle will not be tracked, the default is 10.
PDOP Limit: Customize as you wish.
RTK
FREQ:
Show
the
refresh
rate
of
coordinates.
Note: If you can’t obtain source list successfully,
please check whether receiver is dialed on.
Then, input User and Password for your Ntrip
account.
12.
Click
to save work mode, and then it
will prompt “Please Input Work Mode Name”.
Enter work mode name, and click OK. The
prompt “Save the Mode Successfully!” will pop
up.
Note: The RTCM 1021-1027 messages need to
be switched on or off here. If the mount point
without corresponding messages, please switch
off here.
11.
Elevation Mask: The angle is set for
GNSS Receiver Quick Tour with GNSSTool (PDA Network Mode)
6
13.
Then the green LED will flash and the states
will come from Single to Fix, which means the
rover is getting the correction data from base.
GNSS Receiver Quick Tour with GNSSTool (PDA Network Mode)
7
Download PDF