XCS 12A / XCS 15A
2
15
INTRODUCTION
4
HOOKUP DIAGRAMS
5
INSTALLATION TIPS
QUICK START
6
7
RIGGING
8
PANEL DESCRIPTION
9
FREQUENCY RESPONSE DIAGRAM
10
WIRE CONNECTIONS
TECHNICAL SPECIFICATIONS
11
12
WARRANTY
13
* XCS 12A, XCS 15A are Active Speakers for professional use , they can be used in following
electromagnetic environment: residential, commercial and light industrial, urban outdoors.
They are the apparatusNot intended for rack mounting.
* For XCS 12A, XCS 15A, the peak inrush current is 0.9A
*This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1)this device may not cause harmful interference , and (2)this device
must accept any interference received , including interference that may cause undesired
operation . Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
14
3
XCS
12
XCS
4
13
11
Technical Specifications
4
Hookup Diagrams
Two speaker in stereo operation
Model Active
XCS 12A
System Type
2-Way Active Vented Speaker /Bi-Amp. With DSP processor
Transducer Low
12" Woofer, 2"voice coil
Transducer Driver
o
o
Horn Coverage H x V
1" Neodymium Driver, 1" Voice Coil
90 H x 60 V
Frequency Response
50Hz-20KHz (-6dB)
Crossover Frequency
1.6KHz - DSP Processor
Max SPL
AMP Power Output
125dB Max.
400W Continuous(LF-Class D 350W,HF-Class AB 50W ), 1600W Peak
Connector
Line/Mic With Combo &Link With XLR
External Controls
Volume Control/Lin & Mic Switch/Preset Switch/Power on with
Green LED/ Clip Limiter with Red LED/ Ground Lift.
Digital Presets
Electronic Protections
FLAT -MUSIC-USER
Thermal/Overload/Digital Limiter./Compressor
Power Supply
110-120V
Enclosure Construction
Plastic cabinet,Trapezoidal & Monitor Shape,Metal Grille,
Rubber Feet,3* Handle ( Top and sides)
Mounting
36MM standard pole-mount
Dimensions (HxWxD)
607*380*337mm
Net Weight
14.63 (kg)/ 32.25(Ibs)
50/60Hz or 220V-240V
MAIN OUT R
MAIN OUT L
LINE IN
LINE IN
MIXER
50/60Hz Switchable
Multiple speakers with the same stereo source
MIXER
Model Active
12
XCS 15A
System Type
2-Way Active Vented Speaker /Bi-Amp. With DSP processor
Transducer Low
15" Woofer, 2"voice coil
Transducer Driver
o
o
Horn Coverage H x V
1" Compression Driver, 1" Voice Coil
90 H x 60 V
Frequency Response
45Hz-20KHz (-6dB)
Crossover Frequency
1.6KHz - DSP Processor
Max SPL
AMP Power Output
126dB Max.
400W Continuous(LF-Class D 350W,HF-Class AB 50W ), 1600W Peak
Connector
Line/Mic With Combo &Link With XLR
External Controls
Volume Control/Lin & Mic Switch/Preset Switch/Power on with
Green LED/ Clip Limiter with Red LED/ Ground Lift.
Digital Presets
Electronic Protections
FLAT -MUSIC-USER
Thermal/Overload/Digital Limiter./Compressor
Power Supply
110-120V
Enclosure Construction
Plastic cabinet,Trapezoidal & Monitor Shape,Metal Grille,
Rubber Feet,3* Handle ( Top and sides)
Mounting
36MM standard pole-mount
Dimensions (HxWxD)
625*386*366mm
Net Weight
14 (kg)/ 30.86(Ibs)
50/60Hz or 220V-240V
MAIN OUT RIGHT
MAIN OUT LEFT
LINK TO
NEXT SPEAKER
LINK
LINE IN
LINE IN
LINE IN
LINK TO
NEXT SPEAKER
LINK
LINE IN
50/60Hz Switchable
Use only with a 250V fuse
Use only with a 250V fuse
Use only with a 250V fuse
Use only with a 250V fuse
5
5
Installation Tips
1- Speakers should be placed in a position that allows for unobstructed sound projection. In many
instances is beneficial for speakers to be elevated on tripod stands to achieve maximum
dispersion and reach.
10
2- Use professional advice or service when hanging and installing speakers. Please take precautions
to secure them to prevent them from falling and hurting someone. Care should be taken as to
not damage the cabinet or its components. Please comply with all pertinent Regulations.
3- Use quality cables. Using quality cables will ensure the best possible sound.
4- For best results match the speakers to a good amplifier that matches the wattage and impedance
of your speakers. Proper amplification power results in good quality audio and longer
component life. Check out the power requirement for your cabinet.
5- Avoid pointing a microphone directly at an amplified speaker doing so, could cause feedback
possibly damaging speaker components and your hearing.
Enjoy the sound!
6
11
9
Quick Start
XCS 12A
Make all initial connections with all the equipments powered off, and ensure that all the main
volume controls are turned completely down.
6
1). Connect one side of the signal cable at your audio mixer into output left / right (with StereoJack or XLR) and the other side of the cable into the line input Stereo-Jack) of your active
speaker cabinet.
2). Connect the power cord to mains.
3). Turn on your mixer first, then the active speaker cabinets.
4). Turn up the volume control of the active speaker cabinets.
5). Use PFL function to get the proper input level for the mixer, and adjust the main mix level
control to manipulate the output level.
6). After using, turn off your active speaker cabinets first, then the mixer.
Signal Cable
Signal Cable
XCS 15A
Power Cord
Tripod
Mount
Power Cord
Left
Right
Main Mix
Output
Main Mix
Output
Tripod
Mount
Mixer
10
7
7
8
Panel Description
Rigging
The XCS series speaker cabinet also provides the suspension points for installation.
(M10 1.5PH LENGTH: 30mm).
For further details, please refer to the right illustration(OPTIONAL FUNCTIONAL)
AMP INTERFACE
(1) BI-POLAR MAIN POWER SWITCH
(2) AC POWER SOCKET WITH MAIN FUSE
(3) LINE/MIC INPUT ON COMBO CONNECTOR
(4) LINK OUT ON XLR CONNECTOR
(5) GROUND SWITCH
Eye bolt
(6) THE XCS12A / XCS15A IS SUPPLIED WITH 3 PRESETS, SELECT YOUR FAVORITE AMONG
FLAT-MUSIC-USER
FLAT preset is suited for live sound reinforcement making sound more enjoyable.
MUSIC preset is to equalize the mix for optimal music playback.
USER preset is to change different EQ to match the voice that the user needs, it can be done
Suspension Point
by connecting amplifier module to a PC via the LAN port or the USB port. (The factory preset
of User is the same as normal preset, it can be saved into the product after been modified).
(7) FRONT LED SWITCH
(8) "INPUT SENSITIVITY" SWITCH FOR LINE & MIC
(9) POWER INDICATOR GREEN LED
(10) CLIP INDICATOR RED LED
(9)
(11) (10)
(11) VOLUME CONTROL
(12) USB PLAYER (OPTIONAL)
o
The floor use is as a function of a monitor when the angle is 45
(13) IP CONTROL (OPTIONAL)
(12)
(6)
(5)
(13)
(3)
(4)
45 o
(8)
(7)
(5)
Use only with a 250V fuse
(2)
(1)
XCS 12A / XCS 15A
8
9
Download PDF