IBS PCI SC/I-T
Controller Board for PC Systems
With PCI Bus
Data Sheet 6039B
01/2002
Product Description
INTERBUS Generation 4 controller board with a
host interface for the PCI bus.
Features
–
INTERBUS protocol (IEC 6 11 58)
–
Permanent storage of the parameterization
data on the controller board
–
Data preprocessing on the controller board
–
User-defined addressing
–
PCP 4.x support
–
Firmware download via diagnostic interface
–
Parameter settings via CMD
–
Connection for direct inputs and outputs (in
preparation)
–
Driver software for Windows NT 4.0 and
Windows 2000
–
High-Level Language Interface HLI
–
INTERBUS OPC server
Applications
Connecting simple sensors/actuators and intelligent field devices directly to a control system
with PCI interface via INTERBUS.
Figure 1
6039B
IBS PCI SC/I-T
1
IBS PCI SC/I-T
5
4
3
2
1
6 1 9 0 A 0 0 2
Figure 2
Structure of the IBS PCI SC/I-T controller board
The controller board has the following components:
1
INTERBUS remote bus interface
3
RS-232 interface
2
Connection for direct inputs and outputs
(in preparation)
4
Diagnostic LEDs
5
DIP switches for setting the board number
RS-232 Interface (Mini-DIN Female Connector)
INTERBUS diagnostics can be used via the serial interface (RS-232) using IBS CMD SWT G4 E. In
addition, the controller board firmware can be downloaded. In this way, it is possible to meet future
system requirements by means of updates.
2
6039B
IBS PCI SC/I-T
Programming
Individual applications are created with the support of the corresponding drivers. These drivers
are available for commonly used operating sysOperating System
Windows® NT
tems and programming languages. The drivers
execute the write and read operations to the
MPM and the I/O addresses.
Driver
Installation
Kernel mode
driver
Setting of the board parameters using the SETUP program.
Windows® 2000 WDM driver
Setting of the board parameters using the SETUP program.
To create drivers for other operating systems, use the Device Driver Development Kit,
Order Designation IBS PCI DDK, Order. No. 27 30 27 1.
Watchdog for Host Monitoring
There is a watchdog circuit on the controller
board that you can use for monitoring your PC
program (PC system crash, program runtime error).
6039B
When the watchdog is triggered, the INTERBUS
system is set to a defined state (reset of all outputs).
3
IBS PCI SC/I-T
User Interfaces
User interfaces are available for the following operating systems.
Operating System DDI
Windows® NT 4
X
®
Windows 2000
X
HLI
OPC
X
X
X
X
Device Driver Interface (DDI)
The Device Driver Interface (DDI) is already installed with the drivers, providing the user with the
basic functions for accessing the controller board.
High-Level Language Interface (HLI)
The High-Level Language Interface (HLI) can be used to enable easy development of control programs in a high-level language. It connects to the Device Driver Interface (DDI).
Advantages of the High-Level Language Interface:
–
Direct configuration with CMD
–
Operating system and hardware-independent access to INTERBUS
The HLI supports the following programming
languages:
WIN NT
Microsoft C/C++
X
Borland C/C++
(or compatible)
X
–
Supports many programming languages
–
Faster and easier data exchange using variable names
Integrated bus and error management
Microsoft VB 4.0
(or later)
X
–
–
Identical access to all controller boards
(IBS ... SC)
Borland Delphi 2.0
(or later)
X
–
Automatic PCP communication establishment and monitoring
INTERBUS OPC Server
It is also possible to use an OPC server (Designation IBS OPC SERVER, Order No. 27 29 12 7) as
a High-Level Language Interface or as an interface to any visualization system. The OPC server
makes it possible to access INTERBUS data under Windows NT/Windows 2000 via a standardized
software interface.
For additional information please refer to the OPC server data sheet.
4
6039B
IBS PCI SC/I-T
Comparison of HLI and OPC
High-Level Language Interface:
W IN N T 4
W IN N T 4
V B , C /C + + ,
D e lp h i
O P C - C lie n t
O P C -S e rv e r
H L I
–
Windows 16/32-bit
–
Fast data exchange
–
High-level language programming
OPC server:
–
Windows NT 4.0/Windows 2000
–
Network-wide data exchange
–
Worldwide standard
(High-Level Language Interface and interface to almost all visualization packages)
D D I
6 0 3 9 A 0 0 6
Figure 3
6039B
Comparison of HLI and OPC
5
IBS PCI SC/I-T
Technical Data
Up-to-date information can be found on the Internet at www.phoenixcontact.com.
General Data
Order Designation
IBS PCI SC/I-T
Order No.
27 25 26 0
Dimensions
168 mm x 107mm (6.614 in. x 4.213 in.)
Voltage Supply
VS, controller (PC supply)
5 V DC ±5%
Power consumption
Approximately 3.5 W, typical
Host Interface
Connection method
Direct edge connection
Bus system
PCI 32 bits/33 MHz/5 V
Data width
8, 16 or 32 bits
Address area
256-kbyte memory window
Remote Bus Interface
Connection method
9-pos. D-SUB female connector
Interface type
RS-422
Electrical isolation
Yes (test voltage 0.5 kV)
Diagnostic Interface
Connection method
6-pos. Mini-DIN female connector (PS/2)
Interface type
RS-232
Transmission rate
9600 baud
6
6039B
IBS PCI SC/I-T
Ambient Conditions
Temperature (according to EN 60204-1)
Operation: 0°C to 55°C (32°F to 131°F), storage
and transport: -25°C to 75°C (-13°F to 167°F)
Humidity (according to EN 60204-1)
Storage and operation: 75% on average, 85%
occasionally (DIN 40040); no condensation
Air pressure
Operation: 860 hPa to 1080 hPa (up to 1500 m
[4921 ft.] above sea level)
Storage and transport: 660 hPa to 1080 hPa (up
to 3500 m [11483 ft.] above sea level)
Vibration
2g, criterion 1 according to IEC 68-2-6
Conformance With EMC Directive 89/336/EEC
Noise Immunity Test According to EN 50082-2
Electrostatic discharge (ESD)
EN 61000-4-2
IEC 61000-4-2: 1995
Criterion B
6 kV contact discharge
8 kV air discharge
Electromagnetic fields
EN 61000-4-3
IEC 61000-4-3: 1996
Criterion A
Field strength: 10 V/m
Fast transients (burst)
EN 61000-4-4/
IEC 61000-4-4: 1995
Criterion B
Signal/data lines: 2 kV
Surge test
EN 61000-4-5
IEC 61000-4-5: 1995
Criterion B
Signal/data lines: 1 kV
Conducted interference
EN 61000-4-6
IEC 61000-4-6: 1996
Criterion A
Test voltage 10 V
Noise Emission Test According to EN 55011 (Industrial Area)
Emitted interference
6039B
EN 55011
Class A
7
IBS PCI SC/I-T
Ordering Data
Description
Order Designation
Order No.
Controller board
IBS PCI SC/I-T
27 25 26 0
CD-ROM with documentation in German and
English and drivers for Windows NT 4
CD IBS PCI SC
27 33 00 3
RS-232 cable
PRG CAB MINI DIN
27 30 61 1
User manual for the controller board including dri- IBS PCI SC UM E
ver software for Windows NT 4 and Windows 2000
27 25 25 7
System package with controller board, mounting
set, user manual including driver software and
CMD operating software
27 32 99 4
Configuring and Installing the INTERBUS Product IBS SYS PRO INST UM E
Range User Manual
27 43 80 2
CMD operating software
IBS CMD SWT G4 E
27 21 44 2
INTERBUS OPC server
IBS OPC SERVER
27 29 12 7
Device Driver Development Kit including VxWorks IBS PCI DDK
driver source code
27 30 27 1
Windows NT 4 is a trademark of the Microsoft Corporation.
All drivers, HLI, INTERBUS OPC server (demo version), and all documentation can be downloaded
free of charge at www.phoenixconact.com.
Phoenix Contact GmbH & Co. KG
Flachsmarktstr. 8
32825 Blomberg
Germany
+ 49 - (0) 52 35 - 3-00
+ 49 - (0) 52 35 - 3-4 12 00
www.phoenixcontact.com
Worldwide Locations:
www.phoenixcontact.com/salesnetwork
8
6039B
© Phoenix Contact 01/2002 Technical modifications reserved TNR 90 02 49 5
IBS PCI SC SYSKIT E
Download PDF