Wireless (802.11g) Network Camera

C24-CAMANL Video
Server/Encoder
User’s Guide
Table of Contents
CHAPTER 1 INTRODUCTION.............................................................................................. 1
Overview ............................................................................................................................ 1
Physical Details - Video Server......................................................................................... 2
Package Contents .............................................................................................................. 3
CHAPTER 2 BASIC SETUP ................................................................................................... 4
System Requirements........................................................................................................ 4
APPENDIX A SPECIFICATIONS.......................................................................................... 6
Video Server....................................................................................................................... 6
Regulatory Approvals ....................................................................................................... 6
P/N: 957YDC01MY
Copyright © 2012. All Rights Reserved.
Document Version: 1.0
All trademarks and trade names are the properties of their respective owners.
i
1
Chapter 1
Introduction
This Chapter provides details of the Video Server's features, components and
capabilities.
Overview
The Video Server digitizes analog video signals and transmits digital images directly to your
gateway.
Features
•
Dual Stream Live Video to Multiple Users. The MPEG4 and JPEG encoders built
into the video server generate a ready-to-view video stream. Just connect to the video
server using your gateway.
•
Multi-Protocol Support. Supporting TCP/IP networking, SMTP (E-mail), HTTP and
other Internet related protocols, the Video Server can be easily integrated into your
existing network.
•
IP Filter. Use the IP Filter to block/accept access to the IP addresses.
1
Physical Details - Video Server
Front - Video Server
Reset Button
This button is recessed; you need a pin or paper clip to press it. It can
be activated at any time the video server is in the "ready" mode.
Reset to manufacturer default value and reboot. When pressed
and held over 10 seconds, the settings of Video Server will be set to
their default values.
Note:
After this procedure is completed, the Ready LED will blink three
times to confirm that the reset was completed successfully.
Video Out
Loop-through connection to the video signal from the Video In
connector. It allows direct connection to an external monitor.
Note:
This output must be terminated if not used.
Video In
It supports a single composite video source by using a BNC
connector.
Line Out
If required, an external speaker can be attached here.
Line MIC In
If required, an external microphone can be attached here.
Microphones designed to be used with PCs are usually compatible
with this microphone input.
Network LED
(Green)
On - LAN connection is detected.
Off - LAN connection is not detected
Blinking - Data is being transmitted or received via the LAN
connection.
Active LED
(Green)
Off - No user is viewing the video server.
Ready LED
(Green)
On - Power on.
Blinking - User(s) is viewing the video server.
Off - No power.
Blinking - The Ready LED will blink
Rear - Video Server
Ethernet Port
Use a standard LAN cable to connect your Video Server to the
Device Port of the gateway.
IO Ports
The terminal block includes 1 RS-485 port (2 pins), 2 GND ports, 1
input port and 1 output port.
Connect the supplied 12V power adapter here. Do not use other
power adapters; doing so may damage the video server.
Power Input
2
Package Contents
1.
2.
3.
4.
Video Server
Power Adapter
Video Output Terminator
Quick Installation Guide
3
2
Chapter 2
Basic Setup
This Chapter provides details of installing and configuring the Video Server.
System Requirements
To use the wired LAN interface, a standard 10/100BaseT hub or switch and network cable is
required.
1. Connect the LAN Cable
Connect the Video Server to the device port of the gateway using a standard Ethernet cable.
In installations with multiple devices connected to the device port a 10/100BaseT switch
may be used.
2. Connect the Camera
Connect the video output of the camera to the video in of the Video Server, using a
standard video cable with BNC connectors.
3. Connect Coaxial Terminator on Unused Video Output connector
Terminator provides best quality video if this output is not used for local video viewing.
4. Power Up
Connect the supplied 12Vpower adapter to the Video Server and power up. Use only the
power adapter provided. Using a different one may cause hardware damage.
5. Check the LEDs
•
The Ready LED will turn on briefly, then start blinking. It will blink during startup, which
takes 15 to 20 seconds. After startup is completed, the Ready LED should remain ON.
•
The Network LED should be ON.
6. Adding your Video Server to the C24 Manager
Connect the supplied 12Vpower adapter to the Video Server and power up. Use only the
power adapter provided. Using a different one may cause hardware damage.
Step 1. Log into User Portal (with authorized credentials)
Step 2. Go to System Tab
Step 3. Click on the “Manage Devices” button
Step 4. Click on “Cameras”
Step 5. Select C24-CAMANL Wired IP Analog Camera Adapter
4
Connect the analog camera to the Video In connector of the C24-CAMANL.
Next, connect the C24-CAMANL to the Device LAN port of your gateway with an Ethernet
cable. Finally, plug the power supplies for the camera and C24-CAMANL into an electrical
outlet.
Note: Once connected, the "POWER" and "NETWORK" LEDs on the front of the
C24-CAMANL will turn solid green.
Step 6. Click on “Continue” and follow the installation wizard instructions
5
A
Appendix A
Specifications
Video Server
Model
Video Server
Dimensions
90mm (W) * 30mm (H) * 140mm (D)
Operating Temperature
0° C to 40° C
Storage Temperature
-10° C to 60° C
Network Protocols:
TCP/IP, DHCP, SMTP, NTP, HTTP, HTTPS, UPnP, FTP, RTP,
RTSP
Network Interface:
1 Ethernet 10/100BaseT (RJ45) LAN connection
LEDs
3
Power Adapter
External Power Adapter:12V/1A DC External
PoE: 48V/0.3A
I/O Ports
Input
Output
GND
RS485
x1
x1
x2
x 1 (2pins)
Regulatory Approvals
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this equipment.
(Example - use only shielded interface cables when connecting to computer or peripheral
devices).
6
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
CE Approvals
The Video Server and the Ethernet Video Server meet the guidelines of the European Union
and comply with the 99/5/EEC and RTTE 99/5EG directives, including the following standards:
•
EN60950
•
EN300 328-2
•
EN301 489-1
•
EN301 489-17
This is a Class B product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.
IC Approvals
This devices complies with Industry Canada ICES-003 rule.
Cet appareil est conforme à la norme NMB003 d’Industrie Canada.
7
Download PDF