OP7020 FPGA MMC Simulator SFP Optical Interface - Opal-RT

OP7020
FPGA MMC Simulator
SFP Optical Interface
www.opal-rt.com
Published by
OPAL-RT Technologies, Inc. 1751 Richardson, suite 2525 Montreal, Quebec, Canada H3K 1G6
www.opal-rt.com
© 2014 OPAL-RT Technologies, Inc. All rights reserved
Printed in Canada


SYMBOL DEFINITIONS
The following table lists the symbols used in this document to denote certain conditions:
Symbol
Definition
ATTENTION: Identifies information that requires special consideration
TIP: Identifies advice or hints for the user, often in terms of performing a task
REFERENCE _ INTERNAL: Identifies an additional source of information within the bookset.
CAUTION
Indicates a situation which, if not avoided, may result in equipment or work (data) on the system being
damaged or lost, or may result in the inability to properly operate the process.
Indicates a situation where users must observe precautions for handling electrostatic sensitive devices.
!
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It may also be used to alert against unsafe practices.
!
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in serious injury or
death.
OP7020 User Guide
OPAL-RT Technologies iii


CONTENTS
OP7020 FPGA MMC SIMULATOR........................................................................................................... 7
features. .............................................................................................................................................................7
receiving and verification.....................................................................................................................................7
standard hardware. .............................................................................................................................................7
OP7020 INTERFACE............................................................................................................................ 8
front interface....................................................................................................................................................8
op7020 rear interface..........................................................................................................................................8
synchronization leds............................................................................................................................................9
sfp leds...............................................................................................................................................................9
OP7020 SPECIFICATIONS................................................................................................................... 9
LIMITED WARRANTY............................................................................................................................. 11
limited warranty................................................................................................................................................11
return policy.....................................................................................................................................................11
exclusions.........................................................................................................................................................11
warranty limitation and exclusion.......................................................................................................................12
.....................................................................................................................12
..........................................................................................................................................12
disclaimer of unstated warranties
limitation of liability
OP7020 User Guide
OPAL-RT Technologies 5


6
OPAL-RT Technologies
OP7020 User Guide
OP7020 RCP/HIL Virtex 7TM FPGA Processor Expansion Unit

OP7020 RCP/HIL VIRTEX 7TM
FPGA PROCESSOR EXPANSION UNIT
The OP7020 is a Virtex7-based processor and expansion unit designed to be used with an OPAL-RT
real-time computer. It can be used for floating-point models and projects requiring the use of large
amounts of on-board memory.
The OP7020 is also designed to accommodate up to 16 High Speed fiber optic modules (SFP) that
can be used to communicate with other OPAL-RT simulators, such as the OP7000, OP5607 or any
MMC device under test.
The OP7020 FPGA-based simulation system is connected to a high-performance multi-core INTEL
computer, which is used to compute model sub-systems with a time step value of 10 micros and above
features
• Supports a wide range of SFP and SFP+ transceivers with signaling rates up to 5GBps.
• The VC707 can be programmed using PCIe link or USB interface.
receiving and verification
When you receive your shipment, we strongly recommend that you verify the contents of the
package(s). After carefully opening the package, remove the equipment and components. Make sure
that all the items described below are actually in the box and are undamaged.
standard hardware
The OP7020 includes the following basic hardware:
Item
QTY
OP7020 signal conditioning
chassis
1
Cables
1
3M Ipass X8 M-M 68 Pos.
213-0100-0133
1
1.83 m (6’), 3.5 mm audio, M-M
213-0100-0316
1
1.83 m (6’) USB 2.0, USBA-USBB
213-0100-0442
Adapter
1
PCIe X4 to X4 Host adapter
000-0126-0347
Power cord
1
6’ standard power cord, 10A 25V
213-0100-0308
Test Report
User Documentation CD
N/A
Documentation
Description
Part Number
N/A
OPAL-RT strongly recommends the use of anti-static wrist straps whenever handling any
electronic device provided by OPAL-RT. Damage resulting from electrostatic charges will not be
covered by the manufacturers warranty.
OP7020 User Guide
OPAL-RT Technologies 7
OP7020 RCP/HIL Virtex 7TM FPGA Processor Expansion Unit

OP7020 INTERFACE
front interface
The OP7020 interface includes LEDs and various connectors for status, programming and monitoring
purposes.
A
B
C
D
Figure 1: OP7020 front panel
A.
B.
C.
D.
POWER switch: turns simulator on or off
USB PROGRAM: JTAG connection to program the VC707
SYNCHRO: (LVDS [audio] and Fiber synchronization connectors and LEDs:
SFP socket: connectors for SFP modules
op7020 rear interface
The rear interface contains the PCIe connector, which is the only user interface on the back of the
chassis. Power connections are factory wired.
C
A
B
Figure 2: OP7020 rear panel
A. AC power supply on/off switch: turns AC power supply on or off.
B. Power cable connector: connects AC power supply to appropriate outlet
C. PCIe connector: connects to a real-time computer or expansion chassis.
8
OPAL-RT Technologies
OP7020 User Guide
OP7020 RCP/HIL Virtex 7TM FPGA Processor Expansion Unit
OP7020 Specifications
synchronization leds
A series of four LEDs onthe OP7000 front panel display the device status
LED
Power On
After Load & During
Execution
After Reset
Tx
OFF
GREEN**
OFF
Rx
OFF
GREEN**
OFF
M/S
Default*
ORANGE = Slave
GREEN
PWR
GREEN
GREEN
GREEN
Table 1: OP7020 status LEDs
*The color of the LED on power on depends on the default FPGA configuration. if it is a slave
configuration, it will be orange, if it is a master, it will be green.
**Tx and Rx provide synchronization information. When Transmitting synchronization, the Tx LED will be
green. When receiving synchronization, the Rx LED will be green.
sfp leds
The LEDs associated to the selected channel will light to indicate the channel is selected. LEDs are
arrow-shaped to indicate the channel to which it is associated. LED upward arrow linked to top channel,
downward pointing arrow linked to bottom channel (see below):
LED
Color
Description
Green
ON = SFP is inserted
OFF = no SFP is present
Blinking = channel active in RT-LAB
Green
ON = SFP is inserted
OFF = no SFP is present
Blinking = channel active in RT-LAB
Red
OFF = connection okay
ON = transmission fault
Blinking = reception loss
Red
OFF = connection okay
ON = transmission fault
Blinking = reception loss
CH00
CH01
OP7020 SPECIFICATIONS
Product name
OP7020 FPGA MMC Simulator SFP Optical Interface
Power supply
350W max, 115/230 V auto switching power supply
I/O connectors
PCIe
Number of SFP
Up to 16
SFP speed
2 Gbps
Dimensions (HxWxD)
8.14 x 43 x 35.98cm (3.2” x 17” x 14.2“)
Storage temperature
-55 to 85ºC (-67 to 185ºF)
Relative humidity
10 to 90% non-condensing
Maximum altitude
2000 m (6562 ft.)
OP7020 User Guide
OPAL-RT Technologies 9


10
OPAL-RT Technologies
OP7020 User Guide
Limited Warranty

LIMITED WARRANTY
limited warranty
OPAL-RT Technologies Inc. warrants to the original purchaser and/or ultimate customer (“Purchaser”)
of OPAL-RT products (“Product”) that if any part thereof proves to be defective in material or
workmanship within one (1) year, such defective part will be repaired or replaced, free of charge,
at OPAL-RT Technologies’ discretion, if shipped prepaid to OPAL-RT Technologies Inc. at 1751
Richardson, suite 2525, Montreal, Quebec, Canada, H3K 3G6, in a package equal to or in the original
container. The Product will be returned freight prepaid and repaired or replaced if it is determined
by OPAL-RT Technologies Inc. that the part failed due to defective materials or workmanship.
Otherwise, the fees will be charged to the client (see article “warranty limitation and exclusion”). The
repair or replacement of any such defective part shall be OPAL-RT Technologies’ sole and exclusive
responsibility and liability under this limited warranty.
Purchaser must request an RMA number before shipping any Product for repair:
1. Access the OPAL-RT website (www.opal-rt.com/support/ return-merchandise-authorization-rmarequest), click on support and select Return Merchandise (RMA).
2. Fill out the online form and submit. You will receive a notification with a thread-ID that will be used
for further exchange with support.
3. OPAL-RT’s Support department will evaluate the return and either issue an RMA number via email
using the same thread-ID.
-- If the Product is returned for repair more than 12 months after purchase, the Purchaser is
responsible for the cost of repair. OPAL-RT will assess the repair and prepare a quote. The RMA
number will be sent with the quote.
4. Only when the Purchaser receives the RMA number, may they ship the Product, prepaid, to
OPAL-RT.
return policy
The following fees will apply when customers return products for credit:
A full credit, less a 15% fee and less return fee will only be issued if the product is in perfect working
condition and if the product is returned within 1 month following the shipping date. If repairs are
required on the returned product, the cost of these repairs will be deducted from the credit to be
issued.
No credits will be issued beyond the one month period.
exclusions
If third party products are part of the Product, OPAL-RT will honor the original manufacturer’s warranty.
This limited warranty does not cover consumable items, such as batteries, or items subject to wear or
periodic replacement, including lamps, fuses or filter elements.
OP7020 User Guide
OPAL-RT Technologies 11
Limited Warranty

warranty limitation and exclusion
OPAL-RT Technologies will have no further obligation under this limited warranty. All warranty
obligations of OPAL-RT Technologies are void if the Product has been subject to abuse, misuse,
negligence, or accident or if the Purchaser fails to perform any of the duties set forth in this limited
warranty or if the Product has not been operated in accordance with instructions, or if the Product
serial number has been removed or altered.
disclaimer of unstated warranties
the warranty printed above is the only warranty applicable to this purchase. All other warranties,
express or implied, including, but not limited to, the implied warranties of merchantability or fitness for a
particular purpose are hereby disclaimed.
limitation of liability
It is understood and agreed that OPAL-RT Technologies’ liability, whether in contract, in tort, under
any warranty, in negligence or otherwise shall not exceed the amount of the purchase price paid by
the purchaser for the product and under no circumstances shall OPAL-RT Technologies be liable for
special, indirect, or consequential damages. The price stated for the product is a consideration limiting
OPAL-RT Technologies’ liability. No action, regardless of form, arising out of the transactions under this
warranty may be brought by the purchaser more than one year after the cause of actions has occurred.
12
OPAL-RT Technologies
OP7020 User Guide
CONTACT
OPAL-RT Corporate Headquarters
1751 Richardson, Suite 2525
Montréal, Québec, Canada
H3K 1G6
Tel.: 514-935-2323
Toll free: 1-877-935-2323
Note:
While every effort has been made to ensure
accuracy in this publication, no responsibility
can be accepted for errors or omissions. Data
may change, as well as legislation, and you are
strongly advised to obtain copies of the most
recently issued regulations, standards, and
guidelines.
This publication is not intended to form the
basis of a contract.
Technical Services
www.opal-rt.com/support
UG 13-35241-OP1
06/2014
© OPAL-RT Technologies Inc.
Download PDF