Shuttle XPC Accessory PVG01

Product Specifications
Shuttle Accessory PVG01 –
VGA port expansion kit Shuttle Slim-PCs
Shuttle Accessory
PVG 01
The PVG01 adapter equips compatible Shuttle Slim PCs with an
analog VGA output. For the 1L slim PCs this also means only
one serial interface (COM 1) can be used afterwards.
Note: Slim PCs with H81/H110 chipset support up to two
displays at the same time so that only two out of the available
video outputs can be used.
Scope of
delivery
Specifications
•
•
•
Adapter
Installation guide
Two screws
•
Internal adapter cable, Cable length:
160 mm
Back panel connector: 15-pin Mini DSub female socket (DE15)
Internal connector: Subminiature 2x10pin, 1 mm pitch size, female
•
•
•
Compatibility
Shuttle Order No: POI-PVG01
Images for illustration only.
Compatible to:
1L-Slim-PCs: DX30, DS81, DS87, DH110,
DH170, DQ170
3L-Slim-PCs: XH81(V), XH110(V)
Shuttle Slim PC DS81
1) Front view
2) Rear view with built-in PVG01 VGA port
Shuttle Slim PC XH81 / XH81V
Rear view with built-in PVG01 VGA port
Page 1 14 December 2016
S h u t t l e C o m p u t er Ha n d e l s G m bH
www.shuttle.eu
Fr it z-St r assm an n -St r . 5
25337 Elmsh orn | German y
Tel. +49 (0) 4121-47 68 60
Fax +49 (0) 4121-47 69 00
sale s@ sh u t t le.eu
© 2014 by Shuttle Computer Handels GmbH (Germany). All information subject to change without notice. Pictures for illustration purposes only.
Feature Highlights
Product Specifications
Shuttle Accessory PVG01 – Installation Guide for DS81
Important Notes:
•
•
•
Please also refer to the DS81 installation guide
before fitting processor, memory and drive.
Required Tools for Installation: Phillips
screwdriver and 5mm hexagon screwdriver (or
flat nose pliers)
Caution: For safety reasons, please ensure
that the power cord is disconnected before
opening the case.
Installation of the adapter:
2.
3.
4.
5.
6.
7.
Please remove the case cover, the drive cage
and the processor cooling system as explained
in the DS81 installation guide.
Please remove the serial interface on the right
(COM 2) on the back panel of DS81. Undo the
two hexagon screws, remove the D-Sub
connector from its place and also detach its
onboard connector.
Please now insert the VGA connector of the
PVG01 adapter in the opening and screw it
tightly.
Please connect the other end of the adapter
cable with the appropriate CN25 header on the
mainboard. This connection has a mechanical
reverse polarity protection.
Lead the internal cables of the VGA- and COM
port along the sides of the case making sure
these never obstruct the processor cooling
system.
If desired, please now install further
components according to the DS81 installation
guide. Otherwise please proceed to re-install
the processor cooling, the drive cage and case
cover.
Power on the PC and press the "Delete" key on
the keyboard when the message "Press DEL to
run Setup" is prompted. First select the
"Advanced" tab in the BIOS setup screen, then
go to " Onboard Device Configuration", "Serial
Port Configuration" and "Serial Port 2". Here,
you can set the second serial port to "disabled".
To "Save & Exit" the BIOS setup, press F4 on
the keyboard.
© 2014 by Shuttle Computer Handels GmbH (Germany). All information subject to change without notice. Pictures for illustration purposes only.
1.
Page 2 14 December 2016
S h u t t l e C o m p u t er Ha n d e l s G m bH
www.shuttle.eu
Fr it z-St r assm an n -St r . 5
25337 Elmsh orn | German y
Tel. +49 (0) 4121-47 68 60
Fax +49 (0) 4121-47 69 00
sale s@ sh u t t le.eu
Download PDF