S2K Standalone Keypad Controller Operation Guide

Keyboard Interface Reader application note
__________________________________________________________________________
Introduction:
ACX keyboard interface reader uses Windows HID interface, no need to install the USB driver,
plug and play device.
Reader outputs card number in the cursor position which pre-defined by users.
RF Technology :
EM, Mifare, SONY Felica, HID iCLASS and HID 125KHz
Reader output :
Decimal or Hex depends on the card number bits length.
_______________________________________________________________________________________________________________
Innovative . Explore
Page 1 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
2020 V1.0 Utility Program Operation Guide
This program can apply for ACX 388x reader series
ONE extra RS232 “Y” cable for reader configuration
RS232 “Y” cable RS232 connect to PC, Long USB connect to PC for power supply, Short USB
connect to 388x reader USB Female port.
Run the “2020 V1.0 Utility Program.exe” to configure the reader.
Press the “Scan Device” button.
_______________________________________________________________________________________________________________
Innovative . Explore
Page 2 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
If reader connected properly, the program will read the configuration parametrs from reader and
dispay in the window.
Reader Wiegand Output : Number of bits to be output.
For card serial number (CSN) setting as below:
Sony Felica CSN
: Original CSN 64 bits, reader output full 64 bits CSN
EM CSN
: Original CSN404 bits, reader output full 40 bits CSN
Mifare CSN
: Original CSN 32 / 56 bits, reader output lower 32 bits CSN
For sector number (Usually for HID iCLASS and HID 125KHz)
Input the correct card number bits output (eg 26, 35 bits etc)
If user don’t know the card number format, user can input “0”, andusually click “64 bits data”, then
the reader will read the card number and append leading zeros to totally 64 bits card data length.
This case is suitable for the user has HID multi-card number format card in use.
Card Number Setting: User should know the card number location in the RAW data, input the bit
start location of the card number and input the bit length. If you want to have leading zeros, please
click “Leading ZEROs appended”
Facility Code setting : User should know the Facility Code location in the RAW data, input the bit
start location of the Facility Code and input the bit length. Please also input the Facility Code then
the reader will check the Card’s Facility Code first, if the Facility Code matches, the card number
will be outputed else no output to the teminal.
User can press each button to send its parameters to the reader or select the send all to send all
data to the reader.
After that, disconnet the cable 1 and connect the cable 2, hear 3 beep sounds then the reader
connect to host is successully, user can check the device connect or not in the device manager.
_______________________________________________________________________________________________________________
Innovative . Explore
Page 3 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
Keyboard Output : Click 64 bits output then leading zeros will be append to the raw data. Eg. If
the reader wiegand output is 26 bits, then 34 leading zeros appended, if the reader wiegand output
is 35 bits, then 29 leading zeros appended.
Yoy can select Decial or Hex data output, if the reader wiegand output is not a 4 multipier bits, then
leading zeros will be append to the raw data to be a multipier of 4.
Eg. If he reader wiegand output is 26 bits, 2 leading zeros to be added. If the reader wiegand
output is 35 bits, 1 leading zero to be added.
Output Keys : Five 5 keys user can be defined in the reader after the card data output to the
cursor position.
_______________________________________________________________________________________________________________
Innovative . Explore
Page 4 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
Card Number Format:
HID Card : HID Prox, HID Mifare sector & iClass card.
Symbol: P : parity check, A : Facility code, B : Card Number
1) H10301 standard 26 bits card format : PAAAAAAAABBBBBBBBBBBBBBBBP
2) H10306 HID 34 bits format : EAAAAAAAAAAAAAAAABBBBBBBBBBBBBBBBO
3) H10304 HID 37 bits format : EAAAAAAAAAAAAAAAABBBBBBBBBBBBBBBBBBBO
4) HID Corporate 1000 format : PPAAAAAAAAAAAABBBBBBBBBBBBBBBBBBBBP
Mifare Card
The card number length is 32 bits, no Facility Code & Parity Check Codes
EM Card
The card number length is 40 bits, no Facility Code & Parity Check Codes
_______________________________________________________________________________________________________________
Innovative . Explore
Page 5 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
Example :Case 1.
Standard 26 bits setting:
No leading zeros appended
No Facility checking
Add carriage return
_______________________________________________________________________________________________________________
Innovative . Explore
Page 6 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
Case 2:
HID C1K format (35 bits)
Leading zeros appended
Facility checking, F/C = 111
Add carriage return
_______________________________________________________________________________________________________________
Innovative . Explore
Page 7 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
Case 3:
Mifare 32 bits CSN
Leading zeros appended
Select decimal output
_______________________________________________________________________________________________________________
Innovative . Explore
Page 8 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
Case 4:
Sony Felica 64 bits CSN (only for reader model no. 1111-05)
Select Hex output
Add carriage return
_______________________________________________________________________________________________________________
Innovative . Explore
Page 9 of 10
Keyboard Interface Reader application note
__________________________________________________________________________
Case 5:
Multi card number format in use
Select Hex output
Add carriage return
~ END ~
_______________________________________________________________________________________________________________
Innovative . Explore
Page 10 of 10
Download PDF