Guide Translations
Quick Reference Install Guide
For a Spanish version of the Installation Guide, please download it from
www.directechs.com under Resources.
Remote Start with Keyless Entry
4205-series, 1-button remote
Estimado Cliente:
Si buscas los guías de instalación, por favor de bajar lo del Resources en el
sitio www.directechs.com
Wiring Connections
Primary Harness (H1), 9-pin connector
Heavy Gauge Relay, 6-pin connector
H1/1
LIGHT GREEN BLACK
(-) 200mA FACTORY ALARM DISARM OUTPUT
1
RED
(+) (30A) HIGH CURRENT 12V INPUT
H1/2
GREEN/WHITE
(-) 200mA FACTORY ALARM REARM OUTPUT
2
PINK/WHITE
OUTPUT TO SECOND IGNITION/ACCESSORY CIRCUIT
H1/3
YELLOW
(+) IGNITION OUT (TO ALARM)
3
RED
(+) (30A) HIGH CURRENT 12V INPUT
H1/4
WHITE/BLUE
(-) ACTIVATION INPUT
4
ORANGE
OUTPUT TO ACCESSORY CIRCUIT
H1/5
ORANGE
(-) 500mA GROUND WHEN LOCKED/ANTI-GRIND OUTPUT
5
PURPLE
OUTPUT TO STARTER CIRCUIT
H1/6
BROWN
(-) 200mA HORN OUTPUT
6
PINK
OUTPUT TO PRIMARY IGNITION CIRCUIT
H1/7
RED/WHITE
(-) 200mA TRUNK RELEASE OUTPUT*
H1/8
BLACK
GROUND INPUT
H1/9
WHITE
(+/-) LIGHT FLASH OUTPUT
Satellite harness - 4-pin connector
*Option not available on 1- button
Remote Start harness, (H3) 5-pin connector
Reset and Deletion
Tach Learning
If a feature/virtual tach needs to be reset or the remote controls need to be deleted,
use the following procedure.
To learn the tach signal:
1. Start the vehicle with the key.
2. Within 5 seconds, press and hold the Valet (Control) button.
3. After 3 seconds the system LED will light constant when the tach signal is
learned.
4. Release the Valet (Control) button.
ORANGE
(-) 200mA ACCESSORY OUTPUT
3
PURPLE
(-) 200mA STARTER OUTPUT
Note: Virtual tach is not recommended for diesel vehicles.
4
PINK
(-) 200mA IGNITION OUTPUT
To program Virtual Tach:
1. After the install is complete, remote start the car.
2. If the car does not start on the first attempt, let the remote start attempt again.
3. Once the car starts, let it run until the parking lights come on.
4. When the parking lights come on, shut off the remote start with the remote that’s it! Virtual Tach is programmed.
H3/2
VIOLET/WHITE
TACHOMETER INPUT
H3/3
BROWN
(+) BRAKE SHUTDOWN INPUT
1
LIGHT BLUE
(-) UNLOCK OUTPUT
H3/4
GRAY
(-) HOOD PIN SWITCH SHUTDOWN INPUT
2
EMPTY
NOT USED
H3/5
BLUE/WHITE
(-) 200 mA 2ND STATUS/REAR DEFOGGER OUTPUT
3
GREEN
(-) LOCK OUTPUT
Door Lock, 3-pin connector
Virtual Tach handles disengaging the starter motor during remote starting – it does
not address over-rev. If the customer wants to have the over-rev protection capability, the tach wire must be connected. This may involve more installation shop
charges than initially quoted.
Parking light jumpers
Important: If the Virtual Tach mode over cranks or doesn't crank the
vehicle long enough to start and run the car, use the Bitwriter to add or
subtract the starter output time. You can adjust the output time in increments of 50msec of the learned time using the Bitwriter.
Side View
Antenna
End View
End View
Top View
LED (Programming
indicator)
Control Button
(Valet Switch)
Heavy
Gauge
Relay
Door Lock/unlock
Harness
Reset Features: This resets all features of the system to the factory default
settings.
Note: This feature does not delete the remotes from the system or reset
the Virtual Tach setting
Virtual Tach Reset: Deletes all previously learned values for Virtual Tach,
and on the next remote start sequence the unit begins virtual tach initialization.
Virtual Tach
2
Turn the ignition to the ON position (The heavy gauge pink wire must be connected).
Within 10 seconds, press and release the Valet button: 2 times if you want to
delete remotes, 3 times to reset features or 4 times to reset virtual tach. These
features are described next.
Delete remotes: This feature erases all remotes from the memory of the
system. This is useful in cases when a customer’s remote is lost or stolen.
Note: This does not reset the programmed features of the system or reset
the Virtual Tach setting.
If the tachometer input on the system is connected to the vehicle, the D2D tachometer
input will be ignored.
(-) 200mA STATUS OUTPUT
(-) NEUTRAL SAFETY SWITCH INPUT
2.
When programming tach learning with:
• Analog, the parking lights flash one time
• D2D interface module, the parking lights flash twice
BLUE
BLACK/WHITE
1.
Important: This unit can learn the tachometer with the analog input or
through D2D using an interface module. The unit confirms which source
is used by flashing the parking lights.
1
H3/1
ESP D2D
Installation Points
Note: The “Zap” feature on the Bitwriter does not reset the Virtual tach
setting.
3.
4.
Once you have selected the function step, press the Valet button once more
and hold it. The LED flashes and the horn honks to confirm the selected functional step. Do not release the Valet button.
While holding the Valet button, press the button on the remote control. The
horn honks to confirm that the feature has been successfully reset. You can now
release the Valet button.
Remote Start Shutdown Diagnostics
To perform shutdown diagnostics:
1. With the ignition Off, press and hold the Valet button.
2. Turn the ignition On and then back Off while holding the Valet button.
3. Release the Valet button.
4. Press and release the Valet button. The LED flashes to report the last
shutdown for one minute or until the ignition is turned on, as shown in the
following table:
LED Flashes
1 flash
2 flashes
3 flashes
4 flashes
5 flashes
6 flashes
7 flashes
8 flashes
Shutdown Mode
Timed out
Over-rev shutdown
Low or no RPM, low battery (voltage and virtual tach modes)
Transmitter shutdown (or optional push button)
(-) Hood Shutdown (H3/4 GRAY)
(+) Shutdown (H3/3 BROWN)
(-) Neutral safety shutdown (H3/1 BLACK/WHITE)
Wait-to-start timed out
Antenna
Side View
Bitwriters with a date code of 6a or older require an IC
upgrade (p/n 998M). Some bitwriters with a date code of
6B do not require the IC upgrade, refer to tech tip # 1112
for more information.
Satellite Harness
© 2013 Directed. All rights Reserved.
Primary Harness
Remote Start Harness
The Bitwriter® (p/n 998U)
requires chip version 2.7 or
newer to program this unit.
1
Programming System Features
Feature Menus
Remote Programming
The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the
feature settings using the Valet button.
Default settings are in bold type.
1.
2.
3.
1.
2.
3.
4.
5.
Turn the ignition on, then off.
Select a Menu. Within 10 seconds, Press and hold the Valet button. The number of LED flashes and horn
honks indicates the menu number. A single LED flash and honk indicates menu 1. Two LED flashes and 2
honks indicates menu 2.
When the desired menu LED flashes and honks are heard, release the Valet button.
Select a Feature, within 10 seconds. Press and release the Valet button the number of times corresponding to the feature you wish to change. Then press and hold one more time to select the feature. The LED
flashes and the horn honks to indicate which feature is selected.
Program the Feature. While holding the Valet button, you can program the feature using the remote
control.
Pressing the button on the remote control advances to each feature option. The LED flashes and the horn honks
indicating which option is selected.
Once a feature is programmed:
• Other features can be programmed within the same menu
• Another menu can be selected
• The learn routine can be exited if programming is complete
To access another feature in the same menu:
1. Press and release the Valet button the number of times necessary to advance from the feature you just programmed to the next one you want to program.
2. Then press the Valet button once more and hold it.
To select another menu:
1. Press and hold the Valet button.
2. After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
Opt. 5+
1
Horn function
Off
Siren
20 mS
Siren
30 mS
Siren
40 mS
Siren
50 mS
2
Ignition controlled lock
On
Off
3
Ignition controlled unlock
On
Off
4
Doorlock output duration
0.8 sec.
3.5 sec.
5
Double pulse
unlock
Off
On
6
Double pulse
lock
Off
On
7
Factory Alarm
Disarm function
with unlock
Before unlock
8
Factory Alarm
Disarm Pulses
Single
Double
9
Comfort*
Closure
Comfort
Closure 1
Off
Panic*
On
Off
10
4.
5.
6.
7.
The programming routine exits if any of the following occurs:
• The ignition is turned off
• There is no activity for 30 seconds
• The Valet button is pressed too many times
0.4 sec.
Basic Remote Functions
Button Press
Remote start
only
Function when remote
start is OFF
Function when remote
start is ON
Press for less than 1.5 Start the engine
seconds
Unlock doors
Press for more than 1.5
seconds
Stop the engine
Car finder
Comfort
Closure 2
**Option not available on 1- button
Feature #
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has
previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet
button.
The Bitwriter®
gives you access to a wider range of system options. These additional features and the adjustments that may be programmed are described in the table below.
1
Feature #
Menu 2
The learn routine exits if any of the following occurs:
• The ignition is turned On
• There is no activity for 30 seconds
• The Valet button is pressed too many times
Menu Item
Menu 1
Turn key to the ON position
Within 10 seconds, press and release Valet button one time.
Within 10 seconds, press and hold the Valet button. The LED will flash one time and the horn honks (if connected) to confirm entry into remote programming.
Press the button on the remote control.
The horn honks to confirm the remote has been programmed.
Release the Valet button, and turn the key to the Off position.
The horn sounds one long honk to confirm that remote programming has been exited.
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
1
Engine checking
Virtual tach
voltage
Off
tachometer
2
Engine
Runtime
12 min
24 min
60 min
3
Park light
output
Pulsed
Constant
4
Cranking time
0.6 sec.
0.8 sec.
1.0 sec.
5
Activation
pulse count
1 pulse
2 pulses
3 pulses
6
2nd Ignition
behavior
Ignition
Accessory
1.2 sec.
Feature
Default
Options
7
Accessory
output
Off during
wait-to-start
On during
wait-to-start
Engine Runtime
12 min.
1-60 min.
8
2nd Status
behavior
Normal
Latch rear
defogger
9
Anti-grind
On
Off
10
Diesel start
delay
Off
Timed 15 sec
Timed 30 sec. Timed 45 sec.
11
Timer moderun time *
12 min
3 min
6 min
2
Diesel start type
Off
Timed
3
Diesel start delay time (seconds)
15 sec
1-90 sec.
4
Virtual Tach Fine Tune
Not initialized
0 to 1 second in 50 millisecond
increments
5
Remote control programming
Unlocked
Locked
6
Feature Programming
Unlocked
Locked
*Option not available on 1- button
Opt. 5+
1.4,
1.6,
1.8,
2.0,
4.0 sec
Pulse rear
defogger
9 min
See full Installation Guide for more
detailed information on this system.
Such information and more can be
found online at:
www.directechs.com
QRN4205 2013-06
© 2013 Directed. All rights Reserved.
2
Download PDF