Standard Series Technical Data, 8414

YES
YES
YES
YES
NS
NS3
NS3 YES NS13 NS14 NS15 NS16
F157/1
YES
YES
YES
YES
YES
NS
NS3
NS3 YES NS13 NS14 NS15 NS16
157/2F
NS12
NS12
NS12
NS12
NS12
YES
NS3
NS3 NS12 NS13 NS14 NS15 NS16
ENCLOSURES
224/1
YES
NS12
YES
AS
AS
NS
NS3
223H
Y1
NS12
NS
AS
AS
NS
255
YES
NS12
YES
AS
AS
240
Series
T240
Series
SC240
Series
NS12
NS12
NS12
NS12
NS12
NS12
NS12
NS12
NS12
NS12
AS
The product can be mounted, however, it will not meet Australian Standards requirements.
N3
Product base fouls the accessory mounting bosses, meaning that the product can’t be mounted flush.
N6
The product can be mounted, however, the ‘press to test’ & ‘press to reset’ buttons can’t be pushed.
N8
The finished result looks very unprofessional.
N10
Mounting centres line up, however, the product overhangs the accessory.
N12
The bosses attaching the mechanism back box to the flush plate protrude below the flush plate edge, meaning that the product can’t be mounted flush.
N13
Product base is too large to fit into the accessory.
NS1
Can be direct mounted to surface (55mm mounting centres).
NS2
Can be direct mounted to surface (70mm mounting centres).
NS3
Can be direct mounted to surface (98mm mounting centres).
NS4
Can be direct mounted to surface (124mm mounting centres).
NS5
Can be direct mounted to surface (40mm mounting centres).
NS6
Can be direct mounted to surface (60mm mounting centres).
NS7
Individual Switch & Socket sections for the Standard Range have been formatted to indicate if a product
can or cannot be installed with a particular mounting accessory.
This cross reference charts is best used in conjunction with the “Key” on Page 86.
Product of Clipsal Australia Pty Ltd
ABN 27 007 873 529
Head Office
12 Park Terrace, Bowden
South Australia 5007
Telephone (08) 8269 0511
Facsimile (08) 8340 1724
Internet clipsal.com
E-Mail plugin@clipsal.com.au
Offices in all States
NSW Sydney
Albury
(02) 9794 9200
(02) 6041 2377
VIC
Melbourne
Country Areas
(03) 9207 3200
1800 653 893
QLD
Brisbane
Townsville
(07) 3244 7444
(07) 4729 3333
SA
Adelaide
(08) 8268 0400
WA
Perth
(08) 9442 4444
Can be direct mounted to surface (87mm mounting centres).
TAS
Launceston
(03) 6343 5900
NS8
Can be direct mounted to surface (78mm mounting centres).
NT
Darwin
(08) 8947 0278
NS3 NS12 NS13 NS14 NS15 NS16
NS9
Can be direct mounted to surface (136mm mounting centres).
NS3
NS3 NS12 NS13 NS14 NS15 NS16
NS10
Can be direct mounted to surface (84mm mounting centres - 3 sets, 46mm apart).
NS
NS3
NS3 NS12 NS13 NS14 NS15 NS16
NS11
Can be direct mounted to surface (50mm mounting centres).
NS12
NS
NS3
NS3 NS12 NS13 NS14 NS15 NS16
Area Representatives
NSW Albury
Mid North Coast
Coffs Harbour
Dubbo
Newcastle
NS12
Can be direct mounted to surface (84mm mounting centres).
NS12
NS12
NS
NS3
NS3 NS12 NS13 NS14 NS15 NS16
NS13
Can be direct mounted to surface (75mm mounting centres).
NS12
NS12
NS
NS3
NS3 NS12 NS13 NS14 NS15 NS16
NS14
Can be direct mounted to surface (145mm mounting centres).
NS15
Can be direct mounted to surface (104mm mounting centres).
15V,
15VS, 15VX,
15VXN, 15VXX, 15/2V,
15/2, 15/2S,
15/2VS,
15V15,
15/2VN, 15/2N, 25/2V,
25V,
15D2V, 25/2VS, 25/2VN 15DD2V
25VXA
40
14
16/2,
16,
16N, 16/2S,
16F, 16/2N,
16/15 16/2F
16X
23,
23X
NS16
Can be direct mounted to surface (120mm mounting centres).
NS17
Can be direct mounted to surface (230mm x 40mm mounting centres).
NS18
Can be direct mounted to surface (153mm mounting centres).
T
CODE
YOU WILL FIND THE KEY TO THIS TABLE ON PAGE 86
ACT
Canberra
0419 238 824
0418 164 070
VIC
Bendigo
Geelong
Gippsland
Western Victoria
0418 570 213
0418 527 233
0418 512 680
0419 380 444
Cairns
Mackay
Maryborough
Northern Rivers
Rockhampton
Sunshine Coast
Toowoomba
Townsville
0418 773 254
0418 752 134
0418 664 338
0418 768 902
0419 869 752
0418 711 786
0418 726 394
0418 180 372
The text on the top of the cover can’t be seen.
QLD
DESCRIPTION - SUITABLE
X5
Ensure mounting accessory is set back 25mm from outer wall surface.
Y1
Allow 10mm depth for mechanism and cable protrusion.
Y2
Allow 15mm depth for mechanism and cable protrusion.
Y3
Allow 20mm depth for mechanism and cable protrusion.
Y4
Allow 25mm depth for mechanism and cable protrusion.
Y6
Allow 45mm depth for mechanism and cable protrusion.
Y7
The conduit plugs or conduit have to be shortened to accommodate the large base of product.
86
WA
SA
Bunbury
0418 931 684
Kalgoorlie &
0417 928 981
Eastern Gold Fields
Karratha
0418 937 249
Riverland/Mildura/
Broken Hill
0418 596 145
International Enquiries
International Sales and Marketing
Telephone + 61 8 8269 0587
Facsimile + 61 8 8340 7350
E-Mail export@clipsal.com.au
New Zealand
Clipsal Industries (NZ) Ltd
Telephone (09) 576 3403
Facsimile (09) 576 1015
E-Mail headoffice@clipsal.co.nz
Customer Service
Free Fax (0508) 250 305
Auckland/Mobile Phone (09) 572 0014
Free Phone (0508) CLIPSAL
2547725
You can find this brochure and many
others online in PDF format at:
clipsal.com
Follow the links off the home page
or access the following page directly:
clipsal.com/wat_lib_pdf.cfm
clipsal.com
Special thanks to
Graham Ward (Active Connection Electrical)
and Greg Spurling (Spurling Electrical)
for their contribution to this catalogue.
The shape of the switch dolly is a trade mark of
Clipsal Australia Pty. Ltd.
Clipsal Australia Pty Ltd reserves the right to change
specifications, modify designs and discontinue items
without incurring obligation and whilst every effort is
made to ensure that descriptions, specifications and
other information in this catalogue are correct, no
warranty is given in respect thereof and the company
shall not be liable for any error therein.
© Copyright Clipsal Australia Pty Ltd 2005.
All rights reserved.
This material is copyright under Australian and
international laws. Except as permitted under the
relevant law, no part of this work may be reproduced
by any process without prior written permission of
and acknowledgement to Clipsal Australia Pty Ltd.
O/N 8414 July 05/01
85
(02) 6041 2377
0418 430 361
0418 653 183
0418 822 564
0407 298 792
0418 434 169
0418 686 040
South West Sydney 0419 868 353
Tamworth
0417 714 339
Wagga Wagga
0418 578 903
Wollongong
0418 423 581
technical
te
chn
data
YES
It is often difficult to determine which mounting accessory is best utilised when installing the vast amount
of products in the Clipsal switch & socket ranges. The cross-reference chart in the following pages will
help you to simplify this task.
DESCRIPTION - NOT SUITABLE
O/N 8414 July 05/01
157/1F
MOUNTING ACCESSORIES CROSS REFERENCE CHART
C1-002
15DX
FIRE RATED
WALL BOXES
15DD
JUNCTION
BOXES
MOUNTING ACCESSORIES CROSS REFERENCE CHART
Cat
No.
CODE
STANDARD SERIES - No other range is up to standard
MOUNTING ACCESSORIES CROSS REFERENCE CHART
10,
10D,
10DS,
10DN,
10DLS,
10D15S,
20,
20D,
20DS,
20DN,
15,
15S,
15N,
15D,
15D15,
15DN,
15/15,
15/15S,
15/15N,
15L,
15LN,
15X,
15XX,
25,
25L,
25X,
25XS,
25XA,
25XAN,
25XD,
25S,
25N,
25D,
25D15,
25/15,
25/15S,
25/15N,
25/1510,
42/20,
42/20N
clipsal.com
page
CONTENTS
2
4
12
STANDARD SERIES INTRODUCTION
HOW TO ORDER SECTION
STANDARD SERIES COLOURS
13
14
15
16
19
21
23
23
24
24
26
29
30
31
SWITCHES
Standard Size Flush Switches
Architrave & Miniature Architrave Size Flush Switches
Intermediate & Large Format Size Flush Switches
Flush Plates
Dimmers & Fan Controllers
Timer Controls
Sunset Switches
Switch Multipliers & Booster Element Relay
Under Voltage Relays
Key Tag & Key Operated Switches
Ceiling & Foot Operated Switches
Circuit Identification Products & Mounting Accessories
Cable Connection Accessories
Protected Switches - Moulded and Zinc Diecast
32 - 38
39
40
46
47
50
54
SOCKETS
Various Socket Outlets
Wilco & Clock Connection Accessories
Switched Socket Outlets
Safety, Cooker Socket & Plug and Universal Shaver Outlets
TV Equipment
Chemical Resistant Standard Industrial Range
Protected Switched Socket Outlets - Zinc Diecast
55
61
68
69
81
30 SERIES SWITCH MECHANISMS
SCHEMATIC WIRING DIAGRAMS
MOUNTING TEMPLATES
STANDARD RANGE QUICK REFERENCE GUIDE
FOLD OUT MOUNTING ACCESSORIES CROSS REFERENCE CHART
SETTING THE STANDARD
The Clipsal Standard Range
of Flush Switches, Socket
Outlets and Accessories has
been a firm favourite for many
years, and with good reason.
With pure, uncluttered styling and
timeless lines, Clipsal’s Standard Range
has stood the test of time.
These accessories make it easy to
update or replace switches in the
thousands of Australian homes built in
the 1970s and 80s that already feature
Standard Range products.
Today’s Standard Range however,
features a greater choice of economical
flush switches, sockets and accessories
than have ever been available before.
Switches in all sizes from mini architrave
to large format can be purchased
either assembled or as plates
only, along with printed
mechanisms for
specific functions.
FOR OVER 30 YEARS
Dimmers, fan controllers, time delays,
surface, ceiling and other special
purpose switches are all available in the
Standard Range format.
Socket outlets with features such
as Surge Protection, RCD Protection,
Timers and Dual Voltage also
add to this range to provide for
today’s requirements.
Approvals and Certification
Where required, all Clipsal Standard
Range products have been approved
by The Department Of Energy, South
Australia, and carry the
Approval Mark S/1.
Single/Multi Switch Mechanisms
Note: Depth refers to the dimensions that
switchplate protrudes off the wall surface. It does
not include the amount the mechanism recesses
into the wall.
Standard size switch dimensions are
115mm (length) x 73mm (width) x 11mm (depth).
Each range of switches and socket outlets have different
prefixes at the beginning of the Catalogue Number.
The “3” prefix indicates the product is a
Standard Range Switch Product.
Length
For Standard Range switches
that prefix is ‘3’. For example, a
vertically mounted single gang
switch in Standard Range
is 31VA.
Mounting Centres
Width
Clipsal Standard Range products use the 30 Series Switch
Mechanism, which is a Trademark of Clipsal Australia Pty.
Ltd. Standard Range switches are supplied in one, two,
three, four, five and six-gang formats, meaning that
the gridplate remains the same size, however, a varying
number of switch mechanisms may be used.
HOW TO ORDER SWITCHES
Depth
HOW TO ORDER SWITCHES
3 1VA
This number indicates the number of switch mechanisms
included in the product. Note that the size of the gridplate does
not change, only the number of switch mechanisms is variable.
One
Gang
Two
Gang
Three
Gang
Four
Gang
Five
Gang
Six
Gang
31VA
32VA
33VA
34VA
35VA
36VA
Horizontal or Vertical Formats
31VA
Standard Range Catalogue Numbers will also vary
depending on whether the switch is vertically or
horizontally mounted. For example, 31VA is vertically
mounted whereas 31HA is horizontally mounted.
The ‘A’ in the catalogue number refers to the product
being Assembled.
One
Gang
31HA
31HA
Two
Gang
31VA
32HA
Architrave Switches
The letter “V” indicates the product is
Vertically Mounted.
The letter “H” indicates the product is
Horizontally Mounted.
Three
Gang
32VA
Four
Gang
33VA
33HA
34HA
One
Gang
Two
Gang
Three
Gang
Four
Gang
30
32A
33A
34A
Standard Range switches are also available
in architrave sizes in one, two, three and
four-gang formats.
4
Each format has a different size gridplate.
30 dimensions are 75mm (l) x 32mm (w) x 10mm (d).
32A dimensions are 85mm (l) x 32mm (w) x 10mm (d).
33A dimensions are 113mm (l) x 32mm (w) x 10mm (d).
34A dimensions are 140mm (l) x 32mm (w) x 10mm (d).
HOW TO ORDER SWITCHES (continued)
Miniature Architrave Switches
Miniature Architrave size switches are available in one,
two and three gang formats.
One
Gang
Two
Gang
Three
Gang
30T
32TA
33TA
Each format has a different size gridplate.
30T dimensions are 54mm (l) x 27mm (w) x 10mm (d).
32TA dimensions are 75mm (l) x 27mm (w) x 10mm (d).
33TA dimensions are 98mm (l) x 27mm (w) x 10mm (d).
HOW TO ORDER SWITCHES
A ‘T’ in the Catalogue Number refers to “miniature”
plate size.
Intermediate Switches
One
Gang
Intermediate switches are available in one and
two-gang formats.
Two
Gang
A ‘B’ in the Catalogue Number refers to “intermediate”
plate size. An ‘L’ in the Catalogue Number refers to the
mounting centres being spaced further apart.
The gridplate remains the same size for both formats.
31BA & 32BA dimensions are
95mm (l) x 48mm (w) x 11mm (d).
31BLA & 32BLA dimensions are
95mm (l) x 48mm (w) x 11mm (d).
31BA
31BLA
32BA
32BLA
Large Format Switches
Large Format switches are available from one to
nine-gang formats.
3 1 /2 V A
The gridplate remains the same size for all formats.
Dimensions are 116mm (l) x 116mm (w) x 11mm (d) for
all products.
The “/2” indicates the gridplate is larger than
standard or approximately 50% wider.
One
Gang
Two
Gang
Three
Gang
Four
Gang
Five
Gang
Six
Gang
31/2VA
32/2VA
33/2VA
34/2VA
35/2VA
36/2VA
Seven
Gang
Eight
Gang
Nine
Gang
5
37/2VA
38/2VA
39/2VA
HOW TO ORDER FLUSH PLATES
Standard Range switches can also be purchased with
flush plate only (no switch mechanisms). Note “A” is
not part of the catalogue number which means no
mechanisms are “assembled” in the plate.
See below for one-gang through to six-gang Catalogue
Numbers (please note that the ‘VH’ part of the Catalogue
Number means that mechanisms can be mounted either
vertically or horizontally).
HOW TO ORDER FLUSH PLATES
Standard Size Flush Plates
One Gang
Two Gang
Three Gang
Four Gang
Five Gang
Six Gang
31VH
32VH
33VH
34VH
35VH
36VH
Miniature Architrave Flush Plates
One Gang
Two Gang
Three Gang
31T
32T
33T
Architrave Flush Plates
One Gang
Two Gang
Three Gang
Four Gang
31
32
33
34
Intermediate Flush Plates
One Gang
One Gang
Two Gang
Two Gang
31B
31BL
32B
32BL
6
HOW TO ORDER FLUSH PLATES & NON-STANDARD SWITCHES
HOW TO ORDER FLUSH PLATES
AND NON-STANDARD SWITCHES
Large Format Flush Plates
One Gang
Two Gang
Three Gang
Four Gang
Five Gang
Six Gang
31/2VH
32/2VH
33/2VH
34/2VH
35/2VH
36/2VH
Note
Seven Gang
Eight Gang
Nine Gang
37/2VH
38/2VH
39/2VH
depicts aperture is filled in.
How To Order Non-Standard Switches
Switches can also be ordered with features, including
neon switch mechanisms and indicators, dimmers, fan
controllers, timers, credit card operation, weatherproof
versions and other variations.
Message and Neon Indicator Mechanisms:
Message mechanisms are available in an endless amount
of configurations (see Pages 57-60 for more details).
Neon indicator mechanisms include 30N-RED & 30NCOLOURS. 30/2NM is a switch mechanism with a neon
indicator. Please note that flush plates must be purchased
separately for these products.
30LM
30/2NM
30N-RED
Sunset Switches
Catologue number arrangement is formed as follows:
31VSSR.
‘31’ refers to Single Switch Plate
‘V’ refers to Vertical orientation
‘SS’ refers to Sunset Switch
‘R’ refers to with Relay
31VSSR
Light Dimmers:
include 32E450L (C-Thru ® Leading Edge),
32E450T (C-Thru ® Trailing Edge).
32E450L
7
32E450T
Fan Speed Controller:
is 32E500F.
32E500F
HOW TO ORDER NON-STANDARD SWITCHES (CONTINUED)
HOW TO ORDER
NON-STANDARD SWITCHES (CONTINUED)
Timers - Electronic:
include 31VETR, 31VETR3 & 31VETF (fans).
‘ET’ refers to Electronic Timer.
‘R’ refers to Relay (2 wire, no neutral required).
‘R3’ refers to 3 Wire Relay (3 wire, neutral required).
‘F’ refers to Fan.
31VETR &
31VETR3
31VETF
Timers - Pneumatic:
include 319, 319RA, 319N, 319HP & 319X.
All Pneumatic timer products are prefixed with ‘319’.
‘RA’ refers to a Reverse Action (operation).
‘N’ means that the product includes a Neon.
‘HP’ refers to the product being Hose Proof (weatherproof).
‘X’ means that the product is supplied with an extra switch.
319
319N
319HP
NOTE: Analogue timers are also available, refer page 22.
Key Tag Switches:
include 36VKT3N, 36VKT3NX, 36VKT4, 36VKT4X.
36VKT3N & 36VKT4
36VKT3NX & 36VKT4X
‘V’ refers to Vertical.
‘KT’ refers to Key Tag.
‘N’ refers to Neon.
‘X’ refers to Extra Switch.
F
OF
ON
F
OF
ON
Key Operated Switches:
include 31VK1, 31VK1/2, 31VK2, 31VK2/2.
‘K1’ refers to Key Operated ‘One Way’ Switch.
‘K1/2’ refers to Key Operated ‘Two Way’ Switch.
‘K2’ refers to Key Operated, Locking in both On/Off Positions.
‘K2/2’ refers to Key Operated ‘Two Way’, Locking in both
On/Off Positions.
31VK1
F
OF
31VK1/2 &
31VK2/2
ON
31VK2
F
OF
ON
Common Keyed Switches:
include 31VK1CK, 31VK1/2CK, 31VK2CK, 31VK2/2CK.
‘CK’ - By adding “CK” to Key Operated Switches allows for ‘One
Common Key’ to be used across all switches.
31VK1CK
IP54 Weatherproof Switch:
8
is 31VHWP.
‘WP’ refers to Weather Proof.
31VHWP
31VK1/2CK &
31VK2/2CK
31VK2CK
HOW TO ORDER TELEPHONE, DATA AND TV CONNECTION ACCESSORIES
HOW TO ORDER TELEPHONE, DATA
AND TV CONNECTION ACCESSORIES
Telephone and Data Outlets
The following accessory is available:
One Gang Data Outlet
31VRJ
TV Antenna Connection Accessories
The following accessories are available:
TV Outlet Plate
Coaxial TV Socket
TV Socket
TV Socket
TV-FM Splitter
75 Ohm
3kVAc Isolation, 75 Ohm
F Type Connection, 75 Ohm
Standard Plate
31VTV75
31VTV75ACF
31VTV75F
32VTV75FM
31VTVA
Pay TV Socket
Pay TV & FTA TV
Pay TV & FTA TV
Pay TV & FTA TV
marked ‘PAY TV’
AC Isolation, Standard Plate
F Type, Standard Plate
Screw Coaxial, Standard Plate
31TVF
32TVACFF
32TVFF
32TVSF
Ordering Colours
When ordering switches, colour variations also have to
be taken into consideration, as the Catalogue Number
will change depending on the colour of the product.
Each colour has its own ‘code’, for example, the code
for White Electric is ‘WE’ and the code for Cream is
‘CM’. The Catalogue Number for a Standard Range
One-Gang Vertically Mounted Switch in White Electric
is 31VA,WE.
Refer to ‘Standard Range Colours’ on page 12 for
colour options and their corresponding codes.
9
HOW TO ORDER
SWITCHED SOCKET OUTLETS
HOW TO ORDER SWITCHED SOCKET OUTLETS
Switched Socket Outlets are often referred to as GPO’s
(General Purpose Outlets), Power Points or Power
Outlets. So that there is no confusion, the description
‘Switched Socket Outlets’ will be used throughout this
brochure. Single and twin Socket Outlets are available in
the Standard Range in horizontal and vertical formats.
This number indicates the number of sockets included in the product.
The plate size remains the same for both single and twin switched
socket outlets, only the number of switches and sockets vary.
Catalogue Numbers will vary depending on the
number of sockets and whether the product is
horizontally or vertically mounted. Single Switched
Socket Outlet dimensions are 115mm (length) x 73mm
(width) x 14mm (depth). Twin Switched Socket Outlet
dimensions are 115mm (l) x 72mm (w) x 14mm (d).
15V
The letter ‘V’ indicates that the product is vertically mounted.
Where there is no letter ‘V’, the product is horizontally mounted.
Single Horizontal
Single Vertical
Twin Horizontal
Twin Vertical
15
15V
25
25V
Please note: Single and Twin Automatically Switched
Socket Outlets are also available (Catalogue Numbers
10 and 20).
10 dimensions are 115mm (l) x 73mm (w) x 16mm (d).
20 dimensions are 115mm (l) x 73mm (w) x 16mm (d).
If a Quad Socket Outlet is required, this will only
be achieved by using the Classic C2000 Range
(Catalogue Number C2015D4).
Large Format Switched Socket Outlets
The Catalogue Number for a Single Switched Large
Format Socket Outlet is 15/2, whereas for a Twin
Switched Large Format Socket Outlet it is 23.
15/2 dimensions are 115mm (l) x 115mm (w) x 14mm (d).
23 dimensions are 145mm (l) x 86mm (w) x 15mm (d).
15/2
23
Intermediate Switched Socket Outlets
The Standard Range also includes a Single Switched
Intermediate size Socket Outlet, Catalogue Number 14.
Dimensions are 115mm (l) x 61mm (w) x 13mm (d).
14
Skirting Mounted Switched Socket Outlets
10
Single Automatic (Catalogue Number 11),
Twin Automatic (Catalogue Number 11/2),
Single Switched (Catalogue Number 16), and
Twin Switched (Catalogue Number 16/2) Skirting
Mounted Socket Outlets available.
11 dimensions are 99mm (l) x 45mm (w) x 17mm (d).
11/2 dimensions are 125mm (l) x 50mm (w) x 17mm (d).
16 dimensions are 99mm (l) x 45mm (w) x 14mm (d).
16/2 dimensions are 168mm (l) x 45mm (w) x 13mm (d).
11/2
16/2
HOW TO ORDER SWITCHED SOCKET OUTLETS (Continued)
HOW TO ORDER
SWITCHED SOCKET OUTLETS (Continued)
Special Features and Options
Standard Range Socket Outlets may also be ordered
with special features, including an extra switch
mechanism, safety shutters, neons, double pole
switched versions, deep plate format products and
more. For example, a Single Combination Switched
Socket Outlet may be ordered with Safety Shutters
(Catalogue Number 15S). Please see the main part
of the brochure for Combination and Automatically
Switched Socket Outlets with special features.
Ordering Colours
When ordering switched socket outlets, colour
variations also have to be taken into consideration, as
the Catalogue Number will change depending on the
colour of the product. Each colour has its own ‘code’,
for example, the code for White Electric is ‘WE’ and the
code for Cream is ‘CM’. The Catalogue Number for a
Standard Range Twin Switched Socket Outlet in White
Electric is 25,WE.
Refer to ‘Standard Range Colours’ on page 12 for
colour options and their corresponding codes.
11
STANDARD SERIES COLOURS
STANDARD SERIES COLOURS
The Standard Range offers an unsurpassed choice
of decorator colours, from subtle hues to bold vibrant
colours for maximum impact. Five colours are available
as standard and a further six colours available for a
small surcharge. Two chemical resistant colours are
available at standard prices.
Each colour has its own code, which must be added
to the end of the Catalogue Number, if that particular
colour is desired. For example, if a Vertically Mounted
Single Switch in White Electric is desired, the
Catalogue Number is 31VA,WE.
Standard Colours
Surcharge Colours
White Electric - WE
Cream - CM
Red - RD
Grey - GY
Soft Grey - SG
Desert Sand - DS
Beige - BG
Dove Grey - DO
Brown - BR
Black - BK
Nutmeg - NU
Chemical Resistant Colours
Chemical White - RW
12
Chemical Soft Grey - RS
STANDARD SIZE FLUSH SWITCHES
SWITCHES
Standard Size Flush Switches
These impact resistant flush plates mount to all standard pattern mounting brackets and wall boxes. Being the most
common plate size in the Standard Range, it also offers the largest choice of options.
All vertical models can be converted to horizontal by removing mechanisms and turning them 90o before replacing.
All models have a base projection of 15mm and room projection of 11mm.
STANDARD SIZE FLUSH SWITCHES - HORIZONTAL MOUNTING
Cat. No.
Length
Width
Depth
Mounting Centres
All Products
115mm
73mm
11mm
84mm apart
31HA
A 1 Gang Switch, 250V/10A, 1 way/2 way.
32HA
B 2 Gang Switch, 250V/10A, 1 way/2 way.
33HA
C 3 Gang Switch, 250V/10A, 1 way/2 way.
34HA
D 4 Gang Switch, 250V/10A, 1 way/2 way.
A
B
31HA
C
34HA
D
STANDARD SIZE FLUSH SWITCHES - VERTICAL MOUNTING
Cat. No.
Length
Width
Depth
Mounting Centres
All Products
115mm
73mm
11mm
84mm apart
31VA
A 1 Gang Switch, 250V/10A, 1 way/2 way.
32VA
B 2 Gang Switch, 250V/10A, 1 way/2 way.
33VA
C 3 Gang Switch, 250V/10A, 1 way/2 way.
34VA
D 4 Gang Switch, 250V/10A, 1 way/2 way.
A
B
31VA
C
D
13
35VA
E 5 Gang Switch, 250V/10A, 1 way/2 way.
36VA
F 6 Gang Switch, 250V/10A, 1 way/2 way.
E
F
35VA
ARCHITRAVE AND MINIATURE ARCHITRAVE SIZE FLUSH SWITCHES
ARCHITRAVE AND MINIATURE ARCHITRAVE
SIZE FLUSH SWITCHES
Architrave Size Flush Switches
Architrave switches are available in models with one to four switches. Also available is a single switch model with a
deep plate and a double pole version for caravans, mobile homes and similar.
ARCHITRAVE SIZE FLUSH SWITCHES
Cat. No.
Length
Width
Depth
Mounting Centres
30, 30D, 30/15,
30D15
75mm
32mm
10mm
55mm apart
39
75mm
32mm
10mm
55mm apart
30DD
77mm
35mm
18mm
55mm apart
32A
85mm
32mm
10mm
70mm apart
33A
113mm
32mm
10mm
97mm apart
34A
140mm
32mm
10mm
124mm apart
30
A 1 Gang Switch, 250V/10A, 1 way/2 way.
A
30
C
30D
A 1 Gang Switch, 250V/10A, 1 way, double pole.
30/15
A 1 Gang Switch, 250V/15A, 1 way/2 way.
30D15
A 1 Gang Switch, 250V/15A, 1 way, double pole.
39
B 1 Gang Switch, 250V/10A, 1 way/2 way, 3 position - Low/Off/High.
32A
B
39
33A
D
30DD
30DD
C 1 Gang Switch, 250V/10A, 1 way, double pole, deep plate.
32A
D 2 Gang Switch, 250V/10A, 1 way/2 way.
33A
E 3 Gang Switch, 250V/10A, 1 way/2 way.
34A
F 4 Gang Switch, 250V/10A, 1 way/2 way.
E
34A
F
Miniature Architrave Switches
Miniature Architrave switches are available in single, two or three gang models. They are designed for use in areas
where space is at a premium. All models are suitable only for direct fixing.
MINIATURE ARCHITRAVE SWITCHES
Cat. No.
Length
Width
Depth
Mounting Centres
30T
54mm
27mm
10mm
40mm apart
32TA
75mm
27mm
10mm
60mm apart
33TA
98mm
27mm
10mm
83mm apart
30T
A 1 Gang Switch, 250V/10A, 1 way/2 way.
32TA
B 2 Gang Switch, 250V/10A, 1 way/2 way.
33TA
C 3 Gang Switch, 250V/10A, 1 way/2 way.
14
A
30T
B
33TA
32TA
C
INTERMEDIATE AND LARGE FORMAT SIZE FLUSH SWITCHES
INTERMEDIATE AND LARGE FORMAT SIZE
FLUSH SWITCHES
Intermediate Size Switches
One or two gang intermediate size models offer the convenience of either wall or architrave mounting. This range
offers the option of two mounting centres, 55mm (B) and 78mm (BL).
INTERMEDIATE SIZE SWITCHES
Cat. No.
Length
Width
Depth
Mounting Centres
31BA, 32BA
95mm
48mm
10mm
55mm apart
31BLA, 32BLA
95mm
48mm
10mm
78mm apart
31BA
A 1 Gang Switch, 250V/10A, 1 way/2 way (95 x 48mm at centre).
32BA
B 2 Gang Switch, 250V/10A, 1 way/2 way (95 x 48mm at centre).
31BLA
C 1 Gang Switch, 250V/10A, 1 way/2 way (95 x 48mm at centre).
32BLA
D 2 Gang Switch, 250V/10A, 1 way/2 way (95 x 48mm at centre).
A
B
C
D
31BA
32BA
31BLA
32BLA
Large Format Size Flush Switches
These Large Format Switches are used mainly to replace older accessories, particularly in locations such as hospitals
and schools. Impact resistant, the flush plates are available with up to nine mechanisms.
Plates mount to Standard two gang pattern 157/2 and 164/2 Metal Wall Boxes, 257D2 PVC Deep Wall Boxes, 448 and
448SD Surface Mounting Blocks, 156/2 Mounting Brackets and 154/2 Mounting Clips.
All Large Format Switches have a base projection of 14mm.
LARGE FORMAT SIZE FLUSH SWITCHES - VERTICAL MOUNTING
Cat. No.
Length
Width
Depth
Mounting Centres
All Products
116mm
116mm
11mm
84 x 46mm
31/2VA
A 1 Gang Switch, 250V/10A, 1 way/2 way.
32/2VA
B 2 Gang Switch, 250V/10A, 1 way/2 way.
33/2VA
C 3 Gang Switch, 250V/10A, 1 way/2 way.
34/2VA
D 4 Gang Switch, 250V/10A, 1 way/2 way.
35/2VA
E 5 Gang Switch, 250V/10A, 1 way/2 way.
A
B
31/2VA
C
D
36/2VA
F 6 Gang Switch, 250V/10A, 1 way/2 way.
37/2VA
G 7 Gang Switch, 250V/10A, 1 way/2 way.
38/2VA
H 8 Gang Switch, 250V/10A, 1 way/2 way.
39/2VA
I
E
35/2VA
F
G
15
H
39/2VA
9 Gang Switch, 250V/10A, 1 way/2 way.
I
FLUSH PLATES
Standard Size Flush Plates
Flush plates can be purchased without the 30M Switch for convenience and increased choice. They are available in
Miniature, Architrave, Standard and Large Format sizes.
A series of blank plates are also available for particular applications, such as the termination of unused or looped
cables, mounting of custom equipment or simply blanking off unused openings in wall/wall cladding.
Unused ‘gangs’ can be blanked off with 30P. (see Page 60).
STANDARD SIZE FLUSH PLATES
Cat. No.
Length
Width
Depth
Mounting Centres
All Products
115mm
73mm
11mm
84mm apart
31VH
A 1 Gang Flush Plate.
32VH
B 2 Gang Flush Plate.
33VH
C 3 Gang Flush Plate.
34VH
D 4 Gang Flush Plate.
35VH
E 5 Gang Flush Plate.
36VH
F 6 Gang Flush Plate.
31VX
G Blank Flush Plate.
31VXCB
G Blank Flush Plate, with 30A terminal block.
FLUSH PLATES
A
B
31VH
C
D
35VH
E
F
G
31VX
ARCHITRAVE SIZE FLUSH PLATES
Cat. No.
Length
Width
Depth
Mounting Centres
31
75mm
32mm
11mm
55mm apart
31D
77mm
35mm
18mm
55mm apart
32
85mm
32mm
11mm
70mm apart
33
113mm
32mm
11mm
97mm apart
34
140mm
32mm
11mm
124mm apart
31
A 1 Gang Flush Plate.
31D
B 1 Gang Flush Plate, deep.
32
C 2 Gang Flush Plate.
33
D 3 Gang Flush Plate.
34
E 4 Gang Flush Plate.
A
B
31D
C
D
32
16
E
34
FLUSH PLATES (Continued)
MINIATURE ARCHITRAVE SIZE FLUSH PLATES
Cat. No.
Length
Width
Depth
Mounting Centres
31T
54mm
27mm
10mm
40mm apart
32T
75mm
27mm
10mm
60mm apart
33T
98mm
27mm
10mm
83mm apart
31T
A 1 Gang Flush Plate.
32T
B 2 Gang Flush Plate.
33T
C 3 Gang Flush Plate.
A
31T
B
33T
C
FLUSH PLATES (Continued)
31T
INTERMEDIATE SIZE FLUSH PLATES
Cat. No.
Length
Width
Depth
Mounting Centres
31B
95mm
48mm
10mm
55mm apart
32B
95mm
48mm
10mm
55mm apart
31BL
95mm
48mm
10mm
78mm apart
32BL
95mm
48mm
10mm
78mm apart
31B
A 1 Gang Flush Plate, with 55mm mounting centres.
32B
B 2 Gang Flush Plate, with 55mm mounting centres.
31BL
C 1 Gang Flush Plate, with 78mm mounting centres.
32BL
D 2 Gang Flush Plate, with 78mm mounting centres.
A
B
C
D
31B
32B
31BL
32BL
LARGE FORMAT SIZE FLUSH PLATES - VERTICAL MOUNTING
Cat. No.
Length
Width
Depth
Mounting Centres
31/2VX, 31/2V,
32/2V, 33/2V,
34/2V, 35/2V,
36/2V, 37/2V,
38/2V, 39/2V
116mm
116mm
11mm
84mm x 46mm
31/3VX
162mm
31/2VX
A 1 Gang Blank Flush Plate.
31/2V
B 1 Gang Flush Plate.
32/2V
C 2 Gang Flush Plate.
33/2V
D 3 Gang Flush Plate.
34/2V
E 4 Gang Flush Plate.
35/2V
F 5 Gang Flush Plate.
36/2V
G 6 Gang Flush Plate.
37/2V
H 7 Gang Flush Plate.
38/2V
I
39/2V
J 9 Gang Flush Plate.
31/3VX
K 3 Gang Blank Flush Plate.
A
B
115mm
11mm
31/2VX
84mm x 46mm x 46mm
C
D
8 Gang Flush Plate.
35/2V
E
F
G
H
38/2V
I
17
J
31/3VX
K
FLUSH PLATES, DATA COMMS. & WEATHERPROOF SWITCHES
FLUSH PLATES, DATA COMMS. & WEATHERPROOF SWITCHES
SKIRTING SIZE FLUSH PLATES
Cat. No.
Length
Width
Depth
Mounting Centres
31BMF, 32BMF
99mm
45mm
18mm
78mm apart
35BMF
156mm
45mm
18mm
136mm apart
31BMF
A 1 Gang Flush Plate.
32BMF
B 2 Gang Flush Plate.
35BMF
C 5 Gang Flush Plate.
A
31BMF
B
C
35BMF
32BMF
JUNCTION BOX MOUNTED FLUSH PLATE
Cat. No.
Diameter
Depth
Mounting Centres
31VR
70mm Ø
24mm
51mm
31VR
A Round Plate, suits J.Box Mounting (70mm diameter).
A
31VR
A
31VRJ
Data Comms. Accessory
TELEPHONE/DATA OUTLET PLATE
Cat. No.
Length
Width
Depth
Mounting Centres
31VRJ
115mm
73mm
11mm
84mm apart
31VRJ
A Telephone/Data Outlet Plate, with Cat 3 RJ45 Socket.
Multi-gang Telephone/Data plates should be ordered by purchasing RJ45 Sockets and Plates separately.
IP54 Rated Weatherproof Switch
The 31VHWP is an attractive switchplate designed for use
in outdoor locations such as stairwells, barbecue areas
and gazebos.
For more
information,
check the Clipsal
Standard Range
Weatherproof
Switchplate flyer
O/N 17771.
Completely weatherpoof, the switchplate is particularly suitable
for 30 Series illuminated press buttons and switch mechanisms
that are easy to see at night.
The secret of the switchplate is the translucent rubber membrane
that keeps out water and dust, yet still enables easy switching.
IP54 RATED WEATHERPROOF FLUSH SWITCH
18
Cat. No.
Length
Width
Depth
Mounting Centres
31VHWP
115mm
73mm
11mm
84mm apart
31VHWP
A 1 Gang Weatherproofed Switch Plate (IP54 rated).
A
31VHWP
C-THRU® LIGHT DIMMERS
& FAN CONTROLLERS
In commercial environments too, light dimmers have an
almost endless number of applications. Auditoriums,
restaurants and boardrooms are just a few of the possible
locations in which a light dimmer will offer you full control
of lighting to suit any occasion, and the new C-Thru®
Light Dimmers enable you to choose the right dimmer,
first time - every time.
In a market first, Clipsal has teamed up with other
industry leaders and lighting manufacturers to colour
code both dimmer and load, allowing unprecedented
ease in compatible product selection. Never before has it
been so simple to choose the right dimmer or fan control
product to suit your application.
The C-Thru Light Dimmer unit comprises a separately
switched, compact, modular dimming mechanism rated
at 450W (1.8A). The units utilise state-of-the-art Leading
Edge and Trailing Edge dimming technology to provide
full control of incandescent and low voltage lighting (using
either iron core or electronic transformers).
®
The C-Thru® Product Range is suitable for use in any new
installation, but is also retrofittable, and may be used to
replace a standard switch in any existing installation.
C-THRU® LIGHT DIMMERS & FAN CONTROLLERS
A Clipsal C-Thru® Light Dimmer lets you adjust the
lighting levels in any area, for any occasion. For instance,
you may want to add a little romance to an intimate
dinner, create the right mood for a movie, or leave just
enough light on to navigate your way to the bathroom
during the night.
Please note that the C-Thru® Range of Dimmer and Fan
Speed Control products is immune to the effects of high
frequency (ripple) signal injection on the mains voltage
supply. These signals are commonly injected onto the
mains by the supply authority for such applications as offpeak hot water switching and remote meter monitoring.
This unique Australian design innovation ensures true
flicker-free dimming operation.
Load Compatibility
Each product in the Clipsal C-Thru® Product Range is
colour coded to indicate load compatibility. This colour
coding concept allows easy selection of the right dimmer
for your application.
C-THRU® COLOUR
Load
Symbol
Compatible Loads
Leading
Edge
Dimmer
32E450L
Series
450W
Trailing
Edge
Dimmer
32E450T
Series
450W
Fan Speed
Controller
32E500F
Series
500W
Incandescent lighting
Halogen 240V lamps
Low voltage lighting
with iron-core
transformers
Low voltage lighting
with electronic
transformers
Exhaust fans
(shaded pole
induction motors)
Ceiling fans
(split-phase induction
motors)
Recommended C-Thru® Dimmer/
Fan Control Loads
32E450L
Series
32E450T
Series
Look for the compatibility
sticker on selected lighting
and fan control products.
32E450L, Leading Edge Dimmer, 450W
19
32E500F
Series
Please note: the colour coding scheme outlined above
is the subject of an exclusive Clipsal patent.
DIMMERS, FILTER MODULE & FAN SPEED CONTROLLERS
DIMMERS, FILTER MODULE & FAN SPEED CONTROLLERS
C-THRU ® LIGHT DIMMERS
Cat. No.
Length
Width
Depth
Mounting Centres
32E450L,
32E450T
115mm
73mm
11mm - plate
13mm - knob
84mm apart
30mm - wall recess
32E450LM,
32E450TM
22mm
22mm
13mm - knob
41mm - wall recess
32E450L
A C-Thru Light Dimmer, Leading Edge, 220 - 240V/450W.
32E450LM
B C-Thru ® Light Dimmer Mechanism, Leading Edge, 220 - 240V/450W.
32E450T
A C-Thru® Light Dimmer, Trailing Edge, 220 - 240V/450W.
32E450TM
B C-Thru® Light Dimmer Mechanism, Trailing Edge, 220 - 240V/450W.
N/A
35E450L
®
A
B
35E450LM
35E450TM
HIGH POWER SERIES LIGHT DIMMERS
Cat. No.
Length
Width
Depth
Mounting Centres
31E800T,
31E1000L
115mm
73mm
15mm - plate
11mm - knob
30mm - wall recess
84mm apart
32/1000,
32/2400
115mm
73mm
11mm - plate
13mm - knob
30mm - wall recess
84mm apart
31E800T
A
Trailing Edge Light Dimmer, 250V/800W, suits incandescent and electronic
transformers.
31E1000L
B
Leading Edge Light Dimmer, 250V/1000W, suits incandescent and iron core
transformers.
32/1000
A High Power Leading Edge Light Dimmer, 250V/1000VA, remote wired.
32/2400
B High Power Leading Edge Light Dimmer, 250V/2400VA, remote wired.
A
31E800T
B
32/1000
FILTER MODULE
Cat. No.
Length
Width
Depth
Mounting Centres
32EIND
96mm
70mm
48mm
73mm apart
32EIND
A Inductor Filter Module for use with 32 Series High Powered Dimmers.
A
32EIND
C-Thru® Fan Speed Controller
The C-Thru® Fan Speed Controller unit is rated at 500W (2A), and may be used to provide continuous variable speed
control of motor loads such as ceiling sweep fans and exhaust fans.
C-THRU ® FAN SPEED CONTROLLER
20
Cat. No.
Length
Width
Depth
32E500F
116mm
73mm
11mm - plate
13mm - knob
84mm apart
30mm - wall recess
32E500FM
22mm
22mm
13mm - knob
N/A
41mm - mechanism
32E500F
C-Thru ® Fan Speed Controller, 220 - 240V/500W - standard size gridplate
A and surround complete with one 30M switch and one 32E500FM fan control
mechanism with knob (suits exhaust fans and ceiling fans).
32E500FM
B
C-Thru ® Fan Controller Mechanism, 220 - 240V/500W
(suits exhaust fans and ceiling fans).
Mounting Centres
A
32E500F
B
32E500FM
CEILING SWEEP FAN & ELECTRONIC TIMER CONTROLS
CEILING SWEEP FAN CONTROLLERS
& ELECTRONIC TIMER CONTROLS
Capacitor Ceiling Sweep Fan Controllers
FAN SPEED CONTROLLER FOR “AIRFLOW” ACES36AL & ACES48AL
Cat. No.
Length
Width
Depth
Mounting Centres
All Products
115mm
73mm
11mm - plate
14mm - knob
84mm apart
40mm - wall recess
31VF3CA
A
31VF3CB
A 3 Speed Fan Controller, 100VA, suitable for Airflow ACES56AL and AFLR48.
3 Speed Fan Controller, 100VA, suitable for use with Airflow ACES36AL and
ACES48AL.
A
31VF3CA
31VF3CB
This range is available in White Electric (WE) only.
Electronic Timer Controls
Time delay switches are a convenient way of saving energy in both domestic and commercial applications such as
toilets, bathrooms, stairwells, passageways and other areas that are occupied for a limited or known time, ensuring
electrical loads are switched OFF when not in use.
Clipsal offers three types of time delay switches.
The 31VETR is a push-button electronic time delay switch for loads up to 10A. The timer can be set between 15
seconds and 254 minutes. A remote switching function is also included. Another push-button electronic time delay
switch is the 31VETR3 which includes remote switching facilities. The time setting can be set from 10 seconds to 15
hours. The 31VETF incorporates two switched outputs and can be used to turn the fan load on at the same time as the
light, making it ideal for bathrooms and toilets. When the light is switched off, the fan will remain on for a period of time
that can be set from 2 to 20 minutes.
All models have a base projection of 29mm and all terminals accommodate 2 x 2.5mm² cables.
ELECTRONIC TIMER CONTROLS
Cat. No.
Length
Width
Depth
Mounting Centres
All Products
115mm
73mm
11mm
84mm apart
31VETR
Electronic Timer Control, 254 Minute Time Delay, 250V/10A, 2 wire
- remote switch input. Neon indicator, load on/neon off/neon off, load on.
A Delays between 15 secs and 254 mins. Push button to turn load on for set
period. Toggle push-button to cancel timer and turn load off. Minimum
load is 40mA. Suitable for incandescent or fluorescent lighting.
31VETR3
Electronic Timer Control, 15 Hour Time Delay, 250V/10A, 3 wire - remote
switch input. Neon indicator, programmable state. Delays between 10
A secs and 15 hours. Push button to turn load on for set period. Toggle
push-button to cancel timer. Programmable (NO or NC) output. No
minimum load. Suitable for incandescent or fluorescent lighting.
31VETF
Electronic Timer Control, 10 Minutes Time Delay, 250V/10A, Fans/Lights
B - lights are operated directly off the switch. Lighting load (incandescent
only) is 1600VA, fan load is 400VA. Delays between 2 and 20 minutes.
A
31VETR
31VETR3
B
31VETF
21
TIMERS - PNEUMATIC & ANALOGUE
Pneumatic Time Delay Switches
Pneumatic Time Delay switches are robust timers that operate by using air pressure. When the switch is ‘pushed in’,
the load will remain on until the switch ‘pops out’. The pneumatic pressure can be set by the installer, allowing time
ranges of 2-10 minutes (with care, 20 minutes).
TIMERS - PNEUMATIC & ANALOGUE
PLEASE NOTE: Rotate the control knob carefully and in very small increments (over tightening will damage the
tapered valve).
This time switch operates on the air bleed principle and therefore it is not possible to calibrate it too exactingly. The
timing will vary slightly with manufacturing tolerances, air temperatures, relative humidity and barometric pressure.
Pneumatic Timers are most commonly used in units to operate the lighting in stairwells and other public places such
as schools and gymnasiums.
PNEUMATIC TIME DELAY SWITCHES
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
73mm
11mm
84mm apart
319
A Time Delay Switch.
319RA
A Time Delay Switch, Reverse Action.
319N
B Time Delay Switch, with Neon.
319HP
C Time Delay Switch, Weatherproof/Hose Proof.
319X
D Time Delay Switch, with Extra Switch.
A
B
319
C
D
319HP
Adjusting Pneumatic Time Delay Switches
Analogue Timer Controls
Analogue timer controls are available in both switch, socket and portable socket outlet configurations. Connected
Loads can be set by the user to turn ON and turn OFF at different times of the day according to the users requirement.
Multiple scheduled switching events are supported by all models.
ANALOGUE TIMER CONTROLS
Length
Width
Depth
Mounting Centres
TC15/24,
TC15/15/24,
TC15/15/7D
121mm
79mm
42mm
84mm apart
TC32V1,
TC32V24,
TC32V7D
115mm
73mm
62mm
84mm apart
TC475/24
160mm
130mm
120mm
N/A
A
TC15/24
B
B 24 Hour Timer, single socket outlet, 250V/15A (with safety shutter).
TC15/15/7D
B 7 Day Timer, single power outlet, 250V/15A (with safety shutter).
TC32V1
C 1 Hour Timer, flush switch, 250V/15A.
TC32V24
C 24 Hour Timer, flush switch, 250V/15A.
TC32V7D
C 7 Day Timer, flush switch, 250V/15A.
TC475/24
D 24 Hour Timer, portable dual switch socket.
.. .. . . . ..
..
A 24 Hour Timer, single socket outlet, 250V/10A (with safety shutter).
TC15/15/24
...........
TC15/24
...........
22
Cat. No.
.... . . ....
TC32V1
C
D
TC475/24A
SUNSET SWITCH, BOOSTER ELEMENT RELAYS &
SWITCH MULTIPLIERS
SUNSET SWITCH, BOOSTER ELEMENT RELAYS &
SWITCH MULTIPLIERS
Sunset Switches
Sunset Switches cleverly operate lighting in response to the surrounding light levels. Only
switching lights on when they are needed, Sunset Switches are convenient and they save
money.
The 31VSSR will automatically turn on a connected load when the ambient light level falls
below 10 LUX (at around sunset). The load will then turn off the next morning when the light
level exceeds 30 LUX. Delays of around 8 seconds for turn off and 30 seconds for turn on
take into account any short term changes in light levels that may turn the light on or off.
For more information, check the Clipsal 31VSSR Automatic Sunset Switch
brochure O/N 892-912.
SUNSET SWITCH
Cat. No.
Length
Width
Depth
Mounting Centres
74mm
Plate - 13mm
Mech - 30mm
Box - 37mm
84mm apart
31VSSR
115mm
31VSSR
A Sunset Switch, 250V/10A, 16 hours, 2 wire, IP56 (standard size).
A
31VSSR
Please refer to the 56 & 66 Series Industrial brochure, O/N 826-812 for information about the 56SSR & 56PEDD3 Sunset Switches.
Booster Element Relay
The 31VBER is a Booster Relay for a solar hot water element. The relay drops out when the water reaches a certain
temperature, returning to solar operation. The push button switch incorporates a neon indicator to illuminate when the
Booster Element is operating.
BOOSTER ELEMENT RELAY
Cat. No.
Length
Width
Depth
Mounting Centres
31VBER
115mm
73mm
Plate - 16mm
Button - 4.5mm
84mm apart
31VBER
A Booster Relay for Solar Hot Water Element, 250V/15A.
A
31VBER
Switch Multipliers
Switch multipliers are used to add additional circuits to existing single circuit installations and also provide two-way
switching to an existing single switch installation. They are used instead of wall chasing and running wires down the
wall. In this way, they save both time and money.
SWITCH MULTIPLIERS
Cat. No.
Length
Width
Depth
Mounting Centres
780/1, 780/2,
780K1, 780K2
96mm
70mm
48mm
73mm apart
780/1
A Switch Multiplier, 250V/10A, 1 way.
780/2
B Switch Multiplier, 250V/10A, 2 way.
780K1
C Switch Multiplier, 250V/10A, 1 way
780K2
D Switch Multiplier, 250V/10A, 2 way.
780M
E Switch Multiplier Mechanism, 250V/10A.
780A2M
F Switch Multiplier Mechanism, suits 2 loads 2 way type A bias.
780B2M
F Switch Multiplier Mechanism, suits 2 loads 2 way type B bias.
A
B
780/1
C
23
780/2
D
E
F
780A2M
UNDERVOLTAGE RELAYS & KEY TAG TYPE SWITCHES
UNDERVOLTAGE RELAYS & KEY TAG TYPE SWITCHES
Under Voltage Relays
Specifically designed to reduce overloads to airconditioners and other sensitive equipment during under voltage
(brown-out) situations, the relay switching to open circuit. Excessive loads caused by high in-rush currents when
supply is restored are prevented by the manual reset operation requirement, allowing time to full load restoration.
Under Voltage Relays are designed to drop power to the outlet when an under voltage supply condition (or a ‘brownout’) occurs.
UNDER VOLTAGE RELAYS
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
73mm
11mm
84mm apart
A
15X15RZ
A Single Power Outlet, 250V/15A (with no volt relay and reset switch).
15XRZ
15XRZ
B Single Power Outlet, 250V/10A (with no volt relay and reset switch).
32VRZ
C No Volt Relay and Reset Switch, 250V/10A, (standard size).
B
32VRZ
32VRZ15
C No Volt Relay and Reset Switch, 250V/15A, (standard size).
Key Tag type switches and Key Operated Switches
Clipsal’s Standard Range Key Tag Switches and Room
Access Card Operated Switches are the ideal form
of energy management for hotels, motels and other
locations where power can be left on unnecessarily.
Inserting the key Tag or card into the switch activates
selected circuits to operate lighting, air-conditioning,
television, radio and other appliances. Circuits
to refrigerators and other equipment that need to
continually run are not connected to the switches.
Removing the key Tag or card automatically cuts off
power to all of the circuits to significantly reduce
power wastage.
Refer to adjacent page for detailed information on
this range.
24
C
KEY TAG & KEY OPERATED SWITCHES
KEY TAG TYPE SWITCHES
Length
Width
Depth
Mounting Centres
All Products
115mm
73mm
11mm
84mm apart
36VKT3N
A Key Tag, suits 3 x 20A, 250V a.c., 1/2way circuit with neon.
36VKT3NX
B
36VKT4
A Key Tag Type Switch, suits 4 x 20A, 250V a.c., 1/2way circuits.
36VKT4X
B
A
Key Tag, suits 3 x 20A, 250V a.c., 1/2way circuit, neon, extra 250V a.c.
10A switch.
KEY TAG & KEY OPERATED SWITCHES
Cat. No.
36VK KEY
Key Tag Type Switch, suits 4 x 20A, 250V a.c., 1/2way circuits, extra 10A
250V a.c. switch mech.
B
36VK
KEY TAG ONLY
Cat. No.
Length
Width
Depth
Mounting Centres
35VKT
120mm
45mm
5mm
N/A
2034VKT
92mm
40mm
7mm
N/A
35VKT
A Key Tag, suits 35VKT series switches.
2034VKT
B Short Key Tag, suits 2034VKT series switches.
35VKT
A
B
2034VKT
KEY OPERATED SWITCHES
Cat. No.
Length
Width
Depth
Mounting Centres
All Products
115mm
73mm
*11mm
84mm apart
31VK1
A Key Operated Switch, 250V 20A/16AX, 1 way (locks in OFF position).
31VK1/2
B Key Operated Switch, 250V 20A/16AX, 2 way (locks in OFF position).
31VK2
A Key Operated Switch, 250V 20A/16AX, 1 way (locks in ON & OFF position).
31VK2/2
B Key Operated Switch, 250V 20A/16AX, 2 way (locks in ON & OFF position).
A
B
31VK1
31VK2
* Depth does not include key height.
COMMON KEYED SWITCHES
Cat. No.
Length
Width
Depth
Mounting Centres
All Products
115mm
73mm
*11mm
84mm apart
31VK1CK
A Key Operated Switch, 250V 20A/16AX, 1 way (locks in OFF position).
31VK1/2CK
B Key Operated Switch, 250V 20A/16AX, 2 way (locks in OFF position).
31VK2CK
A Key Operated Switch, 250V 20A/16AX, 1 way (locks in ON & OFF position).
A
B
31VK2/2CK
B Key Operated Switch, 250V 20A/16AX, 2 way (locks in ON & OFF position).
* Depth does not include key height.
31VK1/2CK
31VK2/2CK
Note: Common key number is 60051.
25
CEILING & FOOT OPERATED SWITCHES
Ceiling Switches
Ceiling switches can be used to operate lights, fans and even hot water boosters. They are convenient in that wires do
not have to be run down the wall and they can also be placed in an easier switching position, for example, near a bed.
CEILING & FOOT OPERATED SWITCHES
CEILING SWITCHES
Cat. No.
Diameter
Depth
Mounting Centres
306, 342,
343, 346
52mm Ø
71mm
39mm
306
A
342
Ceiling Switch, 250V/10A a.c., 1 way
A
(available in Brown - BR, White Electric - WE).
343
A
Ceiling Switch, 250V/15A a.c., 1 way
(available in Brown - BR, White Electric - WE).
A
346
B
Ceiling Switch, 250V/10A a.c., 2 way
(available in Brown - BR, White Electric - WE).
306
B
Ceiling Switch Cord in 1.8m lengths
(available in White Electric - WE).
346
WILCO CEILING SWITCH
Cat. No.
Length
Width
Depth
Mounting Centres
PC1
57mm
45mm
18mm
30mm x 28mm
PC1
A
Ceiling Switch, Pull Cord, 10A, double pole with indicator
(available in White Electric - WE).
PC1
A
Foot Operated Switch
The 360 foot operated switch is very handy when installed under desks to operate heaters, lighting or fans. It can also
be placed in other convenient positions when ‘foot switching’ is preferred.
FOOT OPERATED SWITCH
Cat. No.
Length
Width
Depth
Mounting Centres
360
93mm
55mm
29mm
68 x 18mm apart
360
A Foot Switch, 250V/10A, double pole.
* Please note:- For Mounting Accessory suggestions, refer to your Clipsal Representative.
26
A
360
AMERICAN STYLE FLUSH SWITCHES & PLATES
Cat. No.
Length
Width
Depth
Mounting Centres
321,321R
115mm
70mm
8mm
60mm apart
322/1R
116mm
116mm
8mm
60 x 46mm
320,320/15
93mm
35mm
35mm
84mm apart
DC3, DC3-SPDT
93mm
35mm
36mm
84mm apart
AMERICAN STYLE FLUSH SWITCHES & PLATES
AMERICAN STYLE FLUSH SWITCHES AND PLATES - INDIRECT MOUNTING
A
321
B
WSW110,
WSW110/TW,
WSW116,
WSW116/TW
93mm
35mm
32mm
84mm apart
FS169/I,
FS169/15DPDT
93mm
35mm
22mm
84mm apart
321
A 1 Gang Switch Plate (available in White Electric - WE).
321R
B
Switch Plate, suits one x 405 or 415 series socket
(available in Brown - BR, Soft Grey - SG, Grey - GY, White Electric - WE).
322/1R
C
Switch Plate, suits one x 320 series switch and 1 x 405 or 415 series
socket (available in Brown - BR, White Electric - WE).
321R
C
320
D
Switch Mechanism, 250V a.c./10A, 1 way
(available in Brown - BR, Grey - GY, White Electric - WE).
320/15
D
Switch Mechanism, 250V a.c./15A, 1 way
(available in Brown - BR, White Electric - WE).
DC3
E
Flush Switch, 5A, 3 terminal, 1 way, DC, with mounting lugs
(available in Brown - BR).
DC3-SPDT
E
Flush Switch, 5A, 3 terminal, single pole/double throw, DC, with
mounting lugs (available in Brown - BR).
WSW110
F
Flush Switch, 10A, 1 way
(available in Brown - BR, Grey - GY, White Electric - WE).
WSW110/TW
G
Flush Switch, 10A, 2 way
(available in Brown - BR, Grey - GY, White Electric - WE).
WSW116
F Flush Switch, 15A, 1 way (Brown - BR, Grey - GY, White Electric - WE).
WSW116/TW
G Flush Switch, 16A, 2 way (Grey - GY).
D
322/1R
E
DC3
F
G
WSW110/TW
H
FS169/I
H
Flush Switch, 10A, intermediate, with mounting lugs
(available in Grey - GY).
27
FS169/15DPDT
I
Flush Switch, 15A, intermediate, double pole/double throw,
with mounting lugs (available in Grey - GY).
* Please note:- For Mounting Accessory suggestions, refer to your Clipsal Representative.
I
FS169/I
SURFACE & PUSH BUTTON SWITCHES
Surface switches are traditional switches that existed before the introduction of the 30 Series mechanism. They are an
economical alternative to the Heritage Range if a traditional look is preferred.
SURFACE & PUSH BUTTON SWITCHES
WILCO SURFACE SWITCH
Cat. No.
Diameter
Depth
Mounting Centres
SS165/15/2
52mm Ø
17mm
36mm
SS165/15/2
A
Surface Switch, 15A, 2 way, 3 terminal, screw secured cover,
52mm diameter (available in Brown - BR, White Electric - WE).
SS165/15/2
A
SURFACE SWITCHES
Cat. No.
Diameter
Depth
Mounting Centres
362, 362/15, 363
60mm Ø
19mm
48mm apart
389
61mm Ø
27mm
43mm apart
362
A
Surface Switch, 250V/10A, 1 way, 3 terminal
(available in Brown - BR, White Electric - WE).
362/15
A
Surface Switch, 250V/15A, 1 way, 3 terminal
(available in Black - BK, Brown - BR, White Electric - WE).
363
A
Surface Switch, 250V/10A, 2 way, 4 terminal
(available in Black - BK, Brown - BR, White Electric - WE).
389
B
Surface Switch, 250V/25A a.c., 32V d.c., 1 way
(available in Black - BK, White Electric - WE).
362,
362/15,
363
A
389
B
BELL PRESS
Cat. No.
Length
Width
Depth
Mounting Centres
98
60mm
25mm
19mm
48mm apart
98
A Bell Press, Illuminated (available in Brown - BR, White Electric - WE).
A
98
WILCO PUSH BUTTON SWITCHES
Cat. No.
PBS136
Length
28mm
Width
Depth
Mounting Centres
15mm
28mm
(Room protrusion - 18mm)
N/A
15mm
34mm
(Room protrusion - 18mm)
N/A
PBS236
28mm
PBS136
A
Push Button Mechanism with Collar and Locknut, 2A, single pole
(available in White Electric - WE).
PBS236
B
Push Button Mechanism with Collar and Locknut, 2A, double pole
(available in WE).
PBS136
A
B
PBS236
PUSH BUTTON WEATHERPROTECTED 1P53 SURFACE SWITCHES
28
Cat. No.
Length
Width
Depth
Mounting Centres
All products
60mm
35mm
32mm
67mm x 54mm
WPBSW110
A 1 Gang Push Button Surface Switch, 10A, 1 way/2 way, single pole.
WPBSW116
A 1 Gang Push Button Surface Switch, 16A, 1 way/2 way, single pole.
A
* Please note:- For Mounting Accessory suggestions, refer to your Clipsal Representative.
WPBSW110,
WPBSW116
CIRCUIT IDENTIFICATION & MOUNTING ACCESSORIES
CIRCUIT IDENTIFICATION & MOUNTING ACCESSORIES
Circuit Identification Products
Clipsal offers a range of Circuit Identification products to make your job easier.
CIRCUIT IDENTIFICATION PRODUCTS
Cat. No.
Length
Width
Depth
30P, 30PFO
21mm
21mm
10mm
30PID
21mm
21mm
7mm
30P
A Removable Blank Plug, suits 30 Series.
Mounting Centres
30P
A
30PFC
B
30PFO
B Plug, marked “FRIDGE - FREEZER ONLY”.
30PID
C 30 Series ID Circuit Plug, tamper proof.
30PIDA4L*
D Label Sheets, 10 x A4 packet (RD, BU, GR, YL, WE colours available).
9
E Cap, suits switch plate screw recesses.
9SERIES
E Identi-Caps for Circuit Identification.
30PID
C
D
E
9
30PIDA4L
*Software for printing these Label Sheets are available on the Alfred CD-ROM Electronic Trade Product Guide.
Mounting Accessories
Mounting Accessories are for use when mounting 30 Series mechanisms without a flush plate, for example, in a panel
or enclosure.
MOUNTING ACCESSORIES
Cat. No.
Length
Width
Depth
Mounting Centres
ET30
6mm
N/A
N/A
N/A
B30GFZ
45mm
27mm
11mm
24mm apart
F30Z1, F30Z1.5
F30Z2, F30Z4
29mm
29mm
N/A
N/A
31/3F
167mm
116mm
11mm
92mm apart
ET30
A Screw Mounted Earthing Terminal.
B30GFZ
B Mounting Clip with Moulded Surround.
F30Z1
C Mounting Clip Mechanism, suits 1mm thick sheet.
F30Z1.5
C Mounting Clip Mechanism, suits 1.5mm thick sheet.
F30Z2
C Mounting Clip Mechanism, suits 2mm thick sheet.
F30Z4
C Mounting Clip Mechanism, suits 4mm thick sheet.
31/3F
D Three Gang Mounting Flange.
ET30
A
B30GFZ
B
F30Z1
C
D
31/3F
29
CABLE CONNECTION ACCESSORIES
Cable Connection Accessories
Cable Connection Accessories are used for safety and to anchor cables.
CABLE CONNECTION ACCESSORIES
CABLE CONNECTION ACCESSORIES
Cat. No.
Length
Width
Depth
Mounting Centres
31VXCB
115mm
73mm
11mm
84mm apart
32VA15/38TB
115mm
73mm
11mm
84mm apart
TBA
N/A
30mm
N/A
A
38, 38A, 38X,
38Y*, 38Z
22mm Ø
38HD
25mm
21mm
38TB
32mm
22mm
31VXCB
A Blank Plate with 30A Connector Block.
31VXCB
N/A
B
32VA15/38TB
B 30M15 Mech and 38TB Terminal Block, in standard size plate.
38
C Grommet, suits up to 2.5mm2 ordinary duty flex cord.
38A
C Grommet, suits up to 1.5mm2 ordinary duty flex cord.
38X
C Grommet, suits up to 1mm2 ordinary duty flex cord.
32VA15/38TB
C
38
D
38Y
E
38HD
Grommet, suits figure 8 two core flex cord, outer diameter of the
figure 8 core cable is maximum 3mm (each core).
38Y*
D
30Z
C Grommet, suits up to 0.75mm2 light duty flex cord.
38HD
E Grommet, suits up to 2.5mm2 ordinary duty with clamp.
38TB
F Cord Outlet Terminal Block with Grommet, suits 30 series plates.
F
38TB
30
* 38Y Grommet requires an 18mm hole for installation.
PROTECTED SWITCHES
PROTECTED SWITCHES - MOULDED
Length
Width
Depth
Mounting Centres
PSM110
75mm
46mm
51mm
69mm apart
PSM115
75mm
46mm
51mm
69mm apart
PSM110
A Protected Switch, 250V/10A, 1 way/2 way.
PSM115
B Protected Switch, 250V/15A, 1 way/2 way.
A
B
PSM110
PSM115
PROTECTED SWITCHES
Cat. No.
PROTECTED SWITCHES - 250V, 10A, ZINC DIE CAST
Cat. No.
Length
Width
Depth
Mounting Centres
PS110,
PS110-DC,
PS110-DP,
PS110-I,
PS110-N,
PS110-TW
79mm
51mm
50mm
37mm apart
PS110-2,
PS110-2DP,
PS110-2I
101mm
79mm
50mm
82mm apart
PS110
A Single pole.
PS110-DC
A Single pole, DC operation.
PS110-DP
A Double pole.
PS110-I
A Single pole, intermediate.
PS110-N
B Single pole, with neon.
PS110-TW
A Single pole, 2 way.
PS110-2
C Single pole, two gang.
PS110-2DP
C Double pole, two gang.
PS110-2I
C Single pole, two gang, intermediate.
A
PS110
B
PS110-N
C
PS110-2
PROTECTED SWITCHES - 250V, 16A, ZINC DIE CAST
Cat. No.
Length
Width
Depth
Mounting Centres
PS116,
PS116/TW
80mm
51mm
50mm
38mm apart
PS116/2
101mm
80mm
50mm
82mm apart
PS116
A
PS116
A Single pole.
PS116/TW
A Single pole, two gang.
PS116/2
B Single pole, 2 way.
31
B
PS116-2
SOCKET OUTLETS
SOCKET OUTLETS
32
AUTOMATICALLY SWITCHED
SOCKET OUTLETS
AUTOMATICALLY SWITCHED SOCKET OUTLETS
Automatically switched socket outlets are most commonly used to supply power to computers, refrigerators,
microwaves and other accessories that don’t need to be switched off at the socket. Simply inserting the plug into the
outlet provides power to equipment. Removing the plug opens the contacts in the socket to provide the same level of
safety as a conventional switched socket when switched off.
Automatically switched socket outlets are also advantageous in that an appliance which is plugged into it can be
switched on or off from a more convenient location, saving time and effort for more valuable activities.
Available in the Standard Range are single and double automatically switched socket outlets, with a weatherproof
version (ideal for caravans) and a product with a security flap.
The socket outlets are manufactured in accordance with AS/NZ 3100, AS/NZ 3112, AS/NZ 3133 and other relevant
Standards Australia Approval and Testing Specifications, Wiring Rules and Supply Authority requirements.
STANDARD SIZE SINGLE AUTOMATICALLY SWITCHED SOCKET OUTLETS
Cat. No.
Length
Width
Depth
Mounting Centres
10, 10D, 10DS,
10DN, 10DLS,
10D15S
115mm
73mm
16mm
84mm apart
10DWP,
10DWP15,
93mm
82mm
12mm
70 x 54mm
415VF,
415VF15
101mm
80mm
37mm
76 x 65mm
10PL
115mm
73mm
22mm
84mm apart
10
A Single Auto Switched Socket Outlet, 10A, single pole, horizontal mount.
10D
A Single Auto Switched Socket Outlet, 10A, double pole, horizontal mount.
10DS
A
10
A
10DN
B
C
Single Auto Switched Socket Outlet, 10A, double pole
with safety shutters, horizontal mount.
10DLS
D
10D15S
10DN
B
Single Auto Switched Socket Outlet, 10A, double pole
with safety shutters and neon, horizontal mount.
E
10DWP
10DLS
Single Auto Switched Socket Outlet, 10A, round earth, double pole with
C
safety shutters, horizontal mount.
10D15S
D
F
Single Auto Switched Socket Outlet, 15A, double pole
with safety shutters, horizontal mount.
10DWP15
Single Auto Switched Socket Outlet, 10A, double pole flush
weatherproof with flap. *Will be superseded by 415VF
*10DWP
E
*10DWP15
Single Auto Switched Socket Outlet, 15A, double pole flush
F
weatherproof with flap. *Will be superseded by 415VF15
415VF
G
G
415VF15
10PL
H
I
Single Auto Switched Socket Outlet, 10A, double pole with flap,
IP34 rating.
415VF
H
Single Auto Switched Socket Outlet, 15A, double pole with flap,
IP34 rating.
Single Auto Switched Socket Outlet, 10A, single pole with security flap,
horizontal mount.
33
I
10PL
AUTOMATICALLY SWITCHED SOCKET OUTLETS (Continued)
AUTOMATICALLY SWITCHED
SOCKET OUTLETS (Continued)
STANDARD SIZE TWIN AUTOMATICALLY SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
73mm
16mm
84mm apart
20
A Twin Auto Switched Socket Outlet, 10A, single pole.
20D
A Twin Auto Switched Socket Outlet, 10A, double pole.
20DS
A
20
A
Twin Auto Switched Socket Outlet, 10A, double pole
with safety shutters.
20DN
B
20DN
B
Twin Auto Switched Socket Outlet, 10A, double pole
with safety shutters and neons.
20DLS
C
Twin Auto Switched Socket Outlet, 10A, round earth,
double pole and safety shutters.
C
20DLS
SKIRTING MOUNTED SINGLE AUTOMATICALLY SWITCHED SOCKET OUTLET
Cat. No.
Length
Width
Depth
Mounting Centres
11
95mm
45mm
17mm
78mm apart
11
A
Single Auto Switched Socket Outlet, skirting mounted, 10A, single pole
(95 x 45mm at centre).
A
11
SKIRTING MOUNTED TWIN AUTOMATICALLY SWITCHED SOCKET OUTLETS
34
Cat. No.
Length
Width
Depth
Mounting Centres
11/2
125mm
50mm
17mm
104mm apart
11/2MF
11/2MFN
156mm
45mm
18mm
136mm apart
11/2
A
11/2
A
Twin Auto Switched Socket Outlet, skirting mounted, 10A, single pole
(125 x 50mm at centre).
11/2MF
B
Twin Auto Switched Socket Outlet, skirting mounted, 10A, single pole,
suits ducting (156 x 45mm at centre).
11/2MFN
C
Twin Auto Switched Socket Outlet, skirting mounted, 10A, single pole,
safety shutters, neons, suits ducting (156 x 45mm at centre).
B
11/2MF
C
11/2MFN
AUTOMATICALLY AND SPECIAL PURPOSE
SWITCHED SOCKET OUTLETS
Cat. No.
Length
Width
Depth
Mounting Centres
All products
97mm
43mm
29mm
84mm apart
10M
A
Single Auto Switched Socket Outlet Mechanism, 10A, single pole
(available in Brown - BR, Grey - GR, White Electric - WE).
10MD
A
Single Auto Switched Socket Outlet Mechanism, 10A, double pole
(available in Brown - BR, Grey - GR, White Electric - WE).
10MDS
A
Single Auto Switched Socket Outlet Mechanism, 10A, double pole
with safety shutter (available in Brown - BR, White Electric - WE).
10MDLS
B
Single Auto Switched Socket Outlet Mechanism, 10A, round earth,
double pole with safety shutter (available in White Electric - WE).
10MD15S
C
Single Auto Switched Socket Outlet Mechanism, 15A, double pole
with safety shutter (available in White Electric - WE).
10MD20
D
Single Auto Switched Socket Outlet Mechanism, 20A, double pole
(available in White Electric - WE).
AUTOMATICALLY AND SPECIAL PURPOSE
SWITCHED SOCKET OUTLETS
AUTOMATICALLY SWITCHED SOCKET OUTLETS
10M
A
10MDLS
B
C
10MD15S
D
SPECIAL PURPOSE AUTOMATICALLY SWITCHED SOCKET OUTLETS
Cat. No.
Length
Width
Depth
10MP
43mm
42mm
33mm
See mounting detail
(Room protrusion - 3.5mm) Pg. 38
10MDP, 10MDPL,
43mm
10MDP15
42mm
33mm
See mounting detail
(Room protrusion - 3.5mm) Pg. 38
10MP
Mounting Centres
A
Single Auto Switched Socket Outlet Mechanism,
A 10A, single pole, panel mount (available in Brown - BR, Grey - GY,
White Electric - WE). Fascia - 42mm Ø.
10MDP
Single Auto Switched Socket Outlet Mechanism,
B 10A, double pole, panel mount (available in Brown - BR, Grey - GY,
White Electric - WE). Fascia - 42mm Ø.
10MDPL
Single Auto Switched Socket Outlet Mechanism,
C 10A, round earth, double pole, panel mount (available in Brown - BR,
Grey - GY, White Electric - WE). Fascia - 42mm Ø.
10MDP15
Single Auto Switched Socket Outlet Mechanism,
D 15A, double pole, panel mount(available in Brown - BR, Grey - GY,
White Electric - WE). Fascia - 42mm Ø.
415MP and 10MP Panel Mount Detail
10MP
B
10MDP
C
10MDPL
D
10MDP15
35
SPECIAL PURPOSE AUTOMATICALLY
SWITCHED SOCKET OUTLETS (Continued)
SPECIAL PURPOSE AUTOMATICALLY
SWITCHED SOCKET OUTLETS (Continued)
SPECIAL PURPOSE AUTOMATICALLY SWITCHED SOCKET OUTLETS
36
Cat. No.
Length
Width
Depth
Mounting Centres
10MDLB,
10MDSLB,
10MDLSLB,
10MD15SLB,
10MD20LB
60mm
42mm
33mm
50mm apart
G10MDS
46mm
46mm
34mm
N/A
31mm
64mm apart
10MDSLB
10MDLSLB
B
G10FMDS,
G10FMD15S,
G10FMDLS
10MDLB
10MDLE
A
74mm Ø
Single Auto Switched Socket Outlet Mechanism,
A 10A, double pole, less bracket (available in Grey - GY, Soft Grey - SG, White
Electric - WE).
10MD15SLB
C
Single Auto Switched Socket Outlet Mechanism,
A 10A, double pole with safety shutter, less bracket (available in Grey - GY,
White Electric - WE).
10MDLSLB
Single Auto Switched Socket Outlet Mechanism,
B 10A, round earth, double pole, safety shutter, less bracket
(available in White Electric - WE).
10MD15SLB
Single Auto Switched Socket Outlet Mechanism,
C 15A, double pole with safety shutter, less bracket
(available in White Electric - WE).
10MD20LB
D
G10MDS
GEC Miniplug Mechanism, 10A, double pole with safety shutter
E
(available in Grey - GY, White Electric - WE).
G10FMDS
F
10MD20LB
D
E
Single Auto Switched Socket Outlet Mechanism,
20A, double pole, less brackets (available in White Electric - WE).
GEC AF Series Mechanism, 10A, double pole with safety shutter
(available in Grey - GY, White Electric - WE).
G10FMD15S
G
GEC AF Series Mechanism, 15A, double pole with safety shutter
(available in White Electric - WE).
G10FMDLS
H
GEC AF Series Mechanism, 10A, round earth with safety shutter
(available in White Electric - WE).
G10MDS
F
G
GIOFMDS
GIOFMD15S
H
GIOFMDLS
SKIRTING MOUNTED & TOGGLE
SWITCHED SOCKET OUTLETS
SKIRTING MOUNTED SIDE CONNECTING SOCKET OUTLETS
Length
Width
Depth
Mounting Centres
12M
63mm
43mm
29mm
N/A
17M
90mm
43mm
29mm
N/A
12M
Single Auto Switched Socket Outlet, skirting mounted, side connecting
A 250V/10A, single pole (available in Black - BK, Grey - GY,
Red - RD, Soft Grey - SG, White Electric - WE).
17M
Single Switched Socket Outlet, skirting mounted, side connecting,
B 250V/10A, single pole (available in Beige - BG, Black - BK, Brown - BR,
Grey - GY, Red - RD, Soft Grey - SG, White Electric - WE).
12M
A
SKIRTING MOUNTED & TOGGLE
SWITCHED SOCKET OUTLETS
Cat. No.
17M
B
Screws must be at least 15mm long with countersunk
heads and fastened with nuts (for both 12M & 17M)
Toggle Switched Socket Outlets
Toggle switched socket outlets are a foundation product for Clipsal, as they have been around before the 30 Series
mechanism was introduced. They operate similarly to the 30 Series mechanism, however they have a switch design
which is more traditional.
STANDARD SIZE SINGLE TOGGLE SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
70mm
15mm
84mm apart
42/20
A Single Switched Socket Outlet, toggle switch, 250V/20A, single pole.
42/20N
B
42/20
A
Single Switched Socket Outlet, toggle switch, 250V/20A, single pole
with safety shutter and neon.
B
42/20N
SINGLE TOGGLE NARROW ARCHITRAVE SIZE SWITCHED SOCKET OUTLETS - VERTICALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
48mm
15mm
98mm apart
40
A
Single Switched Socket Outlet, toggle switch, 250V/10A, single pole
(115 x 48mm at centre).
40D
A
Single Switched Socket Outlet, toggle switch, 250V/10A, double pole
(115 x 48mm at centre).
37
A
40
UNSWITCHED SOCKET OUTLETS
Unswitched Socket Outlets
Unswitched Socket Outlets are reliable products which have a strong history. They are usually mounted flush against
panels or enclosures and are specialised, in that most Unswitched Socket Outlets are not available in Standard Range
flush plates.
UNSWITCHED SOCKET OUTLETS
UNSWITCHED SOCKET OUTLETS
Cat. No.
Length
Width
Depth
Mounting Centres
405, 405/32,
415, 415L,
415/110, 415/15
96mm
42mm
33mm
(Room protrusion
of 3.5mm)
84mm apart
415MP,
415MP15,
415MPL
43mm
42mm
33mm
(Room protrusion
of 3.5mm)
See mounting detail
Pg. 38
405
A
B
426, 426L,
426/15
66mm Ø
24mm
50mm apart
Single Auto Switched Socket Outlet, 250V/10A, 2 pin parallel
(available in Brown - BR, Grey - GY, White Electric - WE). Fascia - 42mm Ø.
405
A
405/32
Single Auto Switched Socket Outlet, 32V/15A, 2 pin polarised,
B extra low voltage (available in Brown - BR, Grey - GY, White Electric - WE).
Fascia - 42mm Ø.
415
C
415L
Single Auto Switched Socket Outlet, 250V/10A, 3 pin,
D round earth pin (available in Brown - BR, Grey - GY, White Electric - WE).
Fascia - 42mm Ø.
415/110
Single Auto Switched Socket Outlet, 110V/10A, 3 pin,
E 2 round live pins (available in Black - BK, Brown - BR, Grey - GY,
White Electric - WE). Fascia - 42mm Ø.
415/15
F
Single Auto Switched Socket Outlet, 250V/15A, 3 pin,
(available in Brown - BR, Grey - GY, White Electric - WE). Fascia - 42mm Ø.
415MP
G
Single Auto Switched Socket Outlet, 250V/10A, 3 pin,
panel mount (available in Black -BK, White Electric - WE). Fascia - 42mm Ø.
415MP15
H
Single Auto Switched Socket Outlet, 250V/15A, 3 pin,
panel mount (available in Black -BK, White Electric - WE). Fascia - 42mm Ø.
415MPL
I
Single Auto Switched Socket Outlet, 250V/10A, 3 pin, round earth,
panel mount (available in Black -BK, White Electric - WE). Fascia - 42mm Ø.
426
J
Single Auto Switched Socket Outlet, 250V/10A, 3 pin, suits round J-Box
(available in Brown - BR, Grey - GY, White Electric - WE).
426L
Single Auto Switched Socket Outlet, 250V/10A, 3 pin, round earth pin,
K suits round J-Box (available in Brown - BR, Grey - GY,
White Electric - WE).
426/15
L
405/32
C
E
Single Auto Switched Socket Outlet, 250V/10A, 3 pin
(available in Brown - BR, Grey - GY, White Electric - WE). 42mm Ø fascia.
Single Auto Switched Socket Outlet, 32V/15A, 3 pin, suits round J-Box
(available in White Electric - WE).
* Please note:- For Mounting Accessory suggestions,
refer to your Clipsal Representative.
38
415MP and 10MP Panel Mount Detail
415
D
415L
415/110
F
G
415/15
H
415MP
I
J
426
426L
K
L
426/15
WILCO & CLOCK CONNECTION ACCESSORIES
WILCO SOCKET OUTLETS (GREY ONLY)
Length
Width
Depth
Mounting Centres
All products
96mm
42mm
28mm
84mm apart
FOS106
A Single Automatically Switched Socket Outlet, 250V/10A, 3 flat pins.
FOS106R
B
Single Automatically Switched Socket Outlet, 250V/10A, 3 pin,
round earth pin.
FOS106/2R
C
Single Automatically Switched Socket Outlet, 110V/10A, 3 pin,
2 round live pins.
FOS106/15
D Single Automatically Switched Socket Outlet, 250V/15A, 3 flat pins.
FOS105T
E
A
B
FOS106
C
D
WILCO & CLOCK CONNECTION ACCESSORIES
Cat. No.
E
Single Automatically Switched Socket Outlet, 2 flat polarised,
extra low voltage.
FOS106/2R
All models available less lugs (add ‘LL’ to cat. no.).
All models are available in Grey - GY only.
ELECTRIC CLOCK CONNECTION ACCESSORIES
Cat. No.
Length
Width
Depth
Mounting Centres
408/3, 408/3A,
408/4
106mm
59mm
25mm
84mm apart
409/3, 409/3A,
409/4
48mm
35mm
16.5mm
N/A
408/3
A Clock Point Recessed Socket, 250V/5A, 50Hz, 3 pin.
408/3A
B Clock Point Recessed Socket, 3 pin, suitable for other than 250V/50Hz.
408/4
C Clock Point Recessed Socket, 250V/15A, 4 pin.
409/3
D Clock Point Plug, 250V/5A, 50Hz, 3 pin.
408/3
A
B
C
D
409/3
E
409/3A
E Clock Point Plug, 3 pin, suitable for other than 250V/50Hz.
409/4
F Clock Point Plug, 250V/5A, 50Hz, 4 pin.
408/3A
F
409/4
* Please note:- For Mounting Accessory suggestions, refer to your Clipsal Representative.
39
SWITCHED SOCKET OUTLETS
SWITCHED
SOCKET OUTLETS
40
SWITCHED
SOCKET OUTLETS
The Standard Range offers a huge variety of Switched Socket Outlets. Available in 10 and 15A ratings, vertical and
horizontal formats, they also come with a number of options such as neons, extra switches and safety shutters,
not to mention two-piece base versions and more. Also available are large format, intermediate and skirting
mounted versions.
All terminal screws face the same direction and are backed off for easy cable insertion. Socket terminal bores are 5.5mm.
Switched Socket Outlets are manufactured in accordance with AS/NZ 3100, AS/NZ 3112, AS/NZ 3133 and
other relevant Australian and New Zealand Standards, and comply with all relevant Wiring Rules and Electrical
Authorities’ requirements.
SWITCHED SOCKET OUTLETS
Double Pole Switched Socket Outlets
The safety features of double pole switched sockets has led to them becoming an integral part of electrical
accessories in recent times. Standard Range double pole switched socket outlets enable marine craft, caravan and
mobile home manufacturers to install double pole switched sockets in their boats, vans and homes to comply with
AS/NZS3000 requirements.
STANDARD SIZE SINGLE SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
15 Series
115mm
73mm
14mm
84mm apart
15DD Series
115mm
73mm
33mm
84mm apart
15
A Single Switched Socket Outlet, 250V/10A.
15S
A Single Switched Socket Outlet, 250V/10A, with safety shutter.
15N
B Single Switched Socket Outlet, 250V/10A, with safety shutter and neon.
15D
A Single Switched Socket Outlet, 250V/10A, double pole.
15D15
C Single Switched Socket Outlet, 250V/15A, double pole.
15DN
B
15DD
D Single Switched Socket Outlet, 250V/10A, double pole, deep plate.
15DDN
E
Single Switched Socket Outlet, 250V/10A, double pole, deep plate, safety
shutter and neon.
15DX
F
Single Switched Socket Outlet, 250V/10A, double pole with removable
extra switch.
15/15
G Single Switched Socket Outlet, 250V/15A.
A
15
B
C
15N
D
Single Switched Socket Outlet, 250V/10A, double pole
with safety shutter and neon.
E
F
15DDN
G
H
15/15S
G Single Switched Socket Outlet, 250V/15A, with safety shutter.
15/15N
H Single Switched Socket Outlet, 250V/15A, with safety shutter and neon.
15L
I
Single Switched Socket Outlet, 250V/10A, round earth pin.
15LN
J
Single Switched Socket Outlet, 250V/10A, round earth pin, neon and
safety shutter.
15X
K Single Switched Socket Outlet, 250V/10A, with removable extra switch.
15XS
K
15XN
Single Switched Socket Outlet, 250V/10A, with removable extra switch,
L
neon and safety shutter.
15XX
Single Switched Socket Outlet, 250V/10A, with two removable
M
extra switches.
Single Switched Socket Outlet, 250V/10A, with removable extra switch
and safety shutter.
15DD
15/15N
I
15L
J
K
15X
41
L
15XX
M
TWIN SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
TWIN SWITCHED SOCKET OUTLETSHORIZONTALLY MOUNTED
STANDARD SIZE TWIN SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
73mm
16mm
84mm apart
25
A Twin Switched Socket Outlet, 250V/10A.
25S
A Twin Switched Socket Outlet, 250V/10A with safety shutters.
25N
D
25D
B Twin Switched Socket Outlet, 250V/10A, double pole.
25D15
C Twin Switched Socket Outlet, 250V/15A, double pole.
25/15
E Twin Switched Socket Outlet, 250V/15A.
Twin Switched Socket Outlet, 250V/10A with neons and
safety shutters.
A
25
B
C
25N
D
25D15
E
25/15S
E Twin Switched Socket Outlet, 250V/15A, with safety shutters.
25/15N
F
Twin Switched Socket Outlet, 250V/15A, with neons and
safety shutters.
25/1510
G Twin Switched Socket Outlet, 250V/15A and 10A.
25L
H Twin Switched Socket Outlet, 250V/10A, round earth pin.
25X
I
Twin Switched Socket Outlet, 250V/10A with extra one way switch.
25XS
I
Twin Switched Socket Outlet, 250V/10A, extra one way switch
and safety shutters.
MF25X
Twin Switched Socket Outlet, 250V/10A, marked with “FAN” on
J
extra switch.
F
25/15N
G
H
25X
I
J
MF25X
Twin Switched Socket Outlet, 250V/10A, marked with “LIGHT” on
extra switch.
ML25X
K
25XA
L Twin Switched Socket Outlet, 250V/10A with removable extra switch.
25XAN
Twin Switched Socket Outlet, 250V/10A, removable extra switch,
M
neons and safety shutters.
25XD
I
K
ML25X
42
Twin Switched Socket Outlet, 250V/10A, double pole and removable
extra switch.
L
M
25XAN
SINGLE & TWIN SWITCHED SOCKET OUTLETS VERTICALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
73mm
14mm
84mm apart
15V
A Single Switched Socket Outlet, 250V/10A.
15VS
A Single Switched Socket Outlet, 250V/10A with safety shutters.
15VN
B Single Switched Socket Outlet, 250V/10A with safety shutters and neon.
15V15
C Single Switched Socket Outlet, 250V/15A.
15V15N
D Single Switched Socket Outlet, 250V/15A with safety shutters and neon.
15VX
E Single Switched Socket Outlet, 250V/10A with removable extra switch.
15VXS
E
Single Switched Socket Outlet, 250V/10A with safety shutters
and removable extra switch.
15VXN
F
Single Switched Socket Outlet, 250V/10A with safety shutters, neon
and removable extra switch.
15VXX
G
Single Switched Socket Outlet, 250V/10A with two removable
extra switches.
A
B
C
D
SINGLE & TWIN SWITCHED SOCKET OUTLETS VERTICALLY MOUNTED
STANDARD SIZE SINGLE SWITCHED SOCKET OUTLETS - VERTICALLY MOUNTED
15V
15V15N
E
F
15VXX
G
STANDARD SIZE TWIN SWITCHED SOCKET OUTLETS - VERTICALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
15/2V, 15/2VS,
15/2VN, 15D2V,
115mm
73mm
14mm
84mm apart
15DD2V
133mm
83mm
37mm
97mm
25V, 25VXA
115mm
73mm
16mm
84mm apart
15/2V
A Twin Switched Socket Outlet, 250V/10A, two piece base.
15/2VS
A
Twin Switched Socket Outlet, 250V/10A with safety shutters,
two piece base.
15/2VN
B
Twin Switched Socket Outlet, 250V/10A with neons and safety shutters,
two piece base.
15D2V
A Twin Switched Socket Outlet, 250V/10A, double pole, two piece base.
15DD2V
C
25V
D Twin Switched Socket Outlet, 250V/10A.
25VXA
E Twin Switched Socket Outlet, 250V/10A with removable extra switch.
A
15/2V
B
C
15DD2V
Twin Switched Socket Outlet, 250V/10A, double pole with deep plate,
two piece base.
D
E
25V
43
SKIRTING MOUNTED & INTERMEDIATE
SWITCHED SOCKET OUTLETS
SKIRTING MOUNTED SINGLE SWITCHED SOCKET OUTLETS
Cat. No.
Length
Width
Depth
Mounting Centres
All products
98mm
45mm
14mm
78mm apart
16
A
Single Switched Socket Outlet, skirting mounted, 250V/10A with safety
shutter (98 x 45mm at centre).
16N
B
Single Switched Socket Outlet, skirting mounted, 250V/10A with safety
shutter and neon (98 x 45mm at centre).
SKIRTING MOUNTED & INTERMEDIATE
SWITCHED SOCKET OUTLETS
16
16F
C
A
16N
B
Single Switched Socket Outlet, skirting mounted, 250V/10A,
in line terminals (98 x 45mm at centre).
16/15
D
Single Switched Socket Outlet, skirting mounted, 250V/15A
(98 x 45mm at centre).
16X
E
Single Switched Socket Outlet, skirting mounted, 250V/10A
with removable extra switch (125 x 45mm at centre).
16D
A
Single Switched Socket Outlet, skirting mounted, 250V/10A, double pole
(98 x 45mm at centre).
C
16F
D
16/15
E
16X
SKIRTING MOUNTED TWIN SWITCHED SOCKET OUTLETS
Cat. No.
Length
Width
Depth
Mounting Centres
16/2 Series
168mm
45mm
18mm
145mm apart
16/2M Series
156mm
44mm
18mm
136mm apart
16/2
A
16/2S
Twin Switched Socket Outlet, skirting mounted, 250V/10A,
A
with safety shutters (168 x 45mm).
16/2N
B
16/2F
Twin Switched Socket Outlet, skirting mounted, 250V/10A,
C
with straight sides.
16/2MF
Twin Switched Socket Outlet, skirting mounted, 250V/10A, suits ducting
D
(156 x 44mm).
16/2MF1510
E
16/2MFD
D Twin Switched Socket Outlet, skirting mounted, 250V/10A, double pole.
Twin Switched Socket Outlet, skirting mounted, 250V/10A
(168 x 45mm).
Twin Switched Socket Outlet, skirting mounted, 250V/10A, with neons
and safety shutters (168 x 45mm).
Twin Switched Socket Outlet, skirting mounted, 250V/15A & 10A,
suits ducting (156 x 44mm).
16/2
A
16/2N
B
16/2F
C
16/2MF
D
E
16/2MF1510
INTERMEDIATE SINGLE SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
44
Cat. No.
Length
Width
Depth
Mounting Centres
14
115mm
61mm
13mm
84mm apart
14
A Single Switched Socket Outlet, intermediate size, 250V/10A, horizontal.
A
14
LARGE FORMAT & PROTECTED
SWITCHED SOCKET OUTLETS
LARGE FORMAT SIZE SINGLE SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
115mm
14mm
84 x 46mm
15/2
A Single Switched Socket Outlet, large format, 250V/10A, single pole.
15/2
15/2S
A
Single Switched Socket Outlet, large format, 250V/10A, single pole with
safety shutter.
15/2N
B
Single Switched Socket Outlet, large format, 250V/10A, single pole with
safety shutter and neon.
B
LARGE FORMAT & PROTECTED
SWITCHED SOCKET OUTLETS
A
15/2N
LARGE FORMAT SIZE TWIN SWITCHED SOCKET OUTLETS - VERTICALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
115mm
11mm
84 x 46mm
25/2V
A Twin Switched Socket Outlet, 250V/10A (115 x 115mm).
25/2VS
A
Twin Switched Socket Outlet, 250V/10A with safety shutters
(115 x 115mm).
25/2VN
B
Twin Switched Socket Outlet, 250V/10A with neons and safety shutters
(115 x 115mm).
A
B
25/2V
25/2VN
LARGE FORMAT SIZE TWIN SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Cat. No.
Length
Width
Depth
Mounting Centres
23
145mm
86mm
15mm
120mm apart
23
A Twin Switched Socket Outlet, large format, 250V/10A.
A
23
Protected Switched Socket Outlets
Electricity brings with it the life threatening danger of electrocution, and accidents do occur. Clipsal Residual Current
Devices are renowned for being at the forefront of RCD technology. The 15/15EL and 25EL Series are RCD protected
single and twin socket outlets that provide a simple method of individual circuit protection for your safety.
They simply replace existing socket outlets and work by protecting not only their own outlet(s) but all ‘downstream’
outlets on the same circuit. If a fault occurs, power will be cut in less than 40 milliseconds. The 10mA versions are most
commonly used in hospitals and similar locations, whereas the 30mA versions are used in homes and offices.
Surge protection is ideal for protecting electronic devices (computers, TVs, stereos) from damage against harsh surge
and spike voltages that can occur on the mains supply to the premises. They could save you thousands of dollars
protecting expensive electronic equipment. Please refer to the top of the next page for technical information and
dimensions for this range.
45
SAFETY, COOKER SOCKET & PLUG AND UNIVERSAL SHAVER OUTLETS
SAFETY, COOKER SOCKET & PLUG
AND UNIVERSAL SHAVER OUTLETS
PROTECTED SOCKET OUTLETS
Cat. No.
Length
Width
Depth
Mounting Centres
Earth Leakage
Protected Outlets
116mm
74mm
30mm
84mm apart
25SF
115mm
73mm
plate - 17mm
84mm apart
wall recess - 23mm
15/15EL10
A Single Switched Socket Outlet, 250V/15A, with RCD, 10mA.
15/15EL30
A Single Switched Socket Outlet, 250V/15A, with RCD, 30mA.
25EL10
B Twin Switched Socket Outlet, 250V/10A, with RCD, 10mA.
25EL30
B Twin Switched Socket Outlet, 250V/10A, with RCD, 30mA.
25ELSB
C Spacer Block, (L122 x W83 x H30mm).
25SF
D
25SFM
A
15/15EL10
B
25ELSB
C
Twin Switched Socket Outlet, 250V/10A, surge protected,
(L115 x W73 x H16mm).
D
SURGE
PROTECTED
WHEN LIT
E Surge Filter Mechanism , 250V/10A
E
25SF
Cooker Socket Outlet and Plug
The Cooker Socket Outlet and plug are used so that the stove in a new home can be plugged in by the end user at the
last stages of development rather than hard wired by the electrician. This is so that the stove is not a ‘sitting duck’ in a
new home during development for thieves to steal. When maintenance or cleaning is required, it also means that the
stove can be unplugged safely.
COOKER SOCKET OUTLET AND PLUG
Cat. No.
Length
Width
Depth
Mounting Centres
31VCS
115mm
73mm
11mm
84mm apart
800CL
2
A 1.8m, 4mm Cord, with 250V/32A 3 pin plug.
31VCS
B 3 Pin Cooker Socket on Standard Plate, 250V/32A (suits 800CL).
800CL
A
31VCS
B
Universal Shaver Outlets
Universal Shaver Outlets are used in hotels where international customers require different voltage outlets and an
outlet to plug their shavers into. These are superb products for hotels.
UNIVERSAL SHAVER OUTLET
Cat. No.
Length
Width
Depth
Mounting Centres
727
258mm
73mm
17mm
230 x 40mm
727H
184mm
85mm
18mm
152mm
727V
184mm
85mm
18mm
152mm
727
A Universal Shaver Outlet, Dual Voltage, 240V - 110V.
727H
B Universal Shaver Outlet, Dual Voltage, 240V - 110V (horizontal mount).
727V
C Universal Shaver Outlet, Dual Voltage, 240V - 110V (vertical mount).
727
A
B
46
C
727H
727V
TV ANTENNA CONNECTION ACCESSORIES
TV Antenna Connection Accessories
TV ANTENNA CONNECTION ACCESSORIES
Computers and fax machines are now an everyday part of our lives, not only in the office, but also in our homes. The
Standard Range includes TV and communications accessories for every application.
75 Ohm Coaxial Sockets
There are four 75 Ohm coaxial TV sockets available in Standard Range gridplates. Each provides a secure
connection to antenna cables to ensure optimum reception.
Included in the range is a two gang plate with a TV/FM splitter between TV and radio or other signals to be divided
amongst different receivers.
Also included in the Standard Range of telecommunications’ accessories is a gridplate that enables easy installation
of printed circuit boards.
TV ANTENNA CONNECTION ACCESSORIES
Cat. No.
Length
Width
Depth
Mounting Centres
All products
115mm
73mm
11mm
84mm apart
31VTVA
A 1 Gang Standard Pattern Television Assembly.
A
31VTVA
B
31VTV75
B TV Antenna Socket in Standard Plate, 75 Ohm.
31TVF
C “PAY TV” Antenna Socket, in standard size plate.
C
D
32TVACFF
D
31TVF
“PAY TV/FTA TV” with a.c. Isolation.
E
32TVFF
E “PAY TV/FTA TV” with F Type Connection.
F
32TVFF
32TVSF
F “PAY TV/FTA TV” Screw Coaxial Connection.
G
31VTV75ACF
G TV Socket with 3kcV a.c. Isolation, 75 Ohm in standard size plate.
H
31VTV75F
H TV Socket with F Type Connection, 75 Ohm in standard size plate.
47
I
32VTV75FM
I
TV-FM Splitter, in standard size plate.
32VTV75FM
TV CONNECTION SOCKETS, PLUGS & TERMINATORS
AND ACCESSORIES
TV CONNECTION SOCKETS, PLUGS &
TERMINATORS AND ACCESSORIES
48
CONNECTION SOCKETS, PLUGS AND TERMINATORS
Cat. No.
Length
Width
Depth
Mounting Centres
30TV75P,
30TV75CS
33mm
11mm
11mm
N/A
30TV75C,
30TV75C1,
30TV75T
18mm
30TV75P
A Coaxial Cable Plug, 75 Ohm.
30TV75CS
B TV Antenna Connection Socket, 75 Ohm.
30TV75C
C Coaxial RG59 Cable Connection Plug, 75 Ohm (screw type).
30TV75P
A
17mm
17mm
30TV75CS
N/A
B
30TV75C
C
30TV75C1
30TV75C1
D Coaxial RG9 Cable Connection Plug, 75 Ohm (screw type).
D
30TV75T
E Terminator, suits screw type sockets.
E
30TV75CT
SURFACE MOUNTING CONNECTION ACCESSORY
Cat. No.
Length
Width
Depth
Mounting Centres
30TV75S
54mm
29mm
25mm
N/A
30TV75S
A Coaxial Cable Surface Socket, 75 Ohm.
A
30TV75S
TV ANTENNA MECHANISMS
AND FLY LEADS
Cat. No.
Length
Width
Depth
Mounting Centres
30PFM
22mm
22mm
26mm
N/A
30TVM
22mm
22mm
19mm
N/A
30TVFM
21mm
21mm
19mm
N/A
30TV75M
22mm
22mm
38mm
N/A
30TV75MF
22mm
22mm
35mm
N/A
30TV75MACF
22mm
22mm
33mm
N/A
30TV75MS
22mm
22mm
28mm
N/A
30PFM
A “F” Type Connection, 75 Ohm suits “PAY TV”.
30TVM
B TV Socket, 300 Ohm type (rear clip).
30TVFM
C TV Socket, 300 Ohm type (front clip).
30TV75M
D TV Antenna Socket, 75 Ohm, suits 30 series plates.
30TV75MF
E TV Antenna Socket, 75 Ohm, with “F” type connection.
30TV75MACF
F TV Antenna Socket, 75 Ohm, with 3kV a.c. isolation.
30TV75MS
G TV Antenna Socket, 75 Ohm (screw fi xing, solderless).
A
TV ANTENNA MECHANISMS AND FLY LEADS
ANTENNA MECHANISMS
B
30PFM
C
D
30TV75M
E
30TV75MACF
F
G
30TV75MS
Fly Leads
Fly leads are loose, floating cable as opposed to being hard wired, meaning that they are ‘free and floating’ to allow
them to be attached between two points.
FLY LEADS
Cat. No.
Description
3105FL118MW
A Male to Male Fly Lead, 1.8M.
3105FL118FW
B Male to Female Fly Lead, 1.8M.
A
B
3105FL118MW
49
CHEMICAL RESISTANT STANDARD
INDUSTRIAL RANGE
50
CHEMICAL RESISTANT STANDARD INDUSTRIAL RANGE
CHEMICAL RESISTANT
STANDARD INDUSTRIAL RANGE
has been colour matched to standard White Electric.
Resistant Soft Grey (RS) has been matched to
standard Soft Grey.
Improved Chemical Resistance
The majority of Clipsal products are manufactured from
polycarbonate, which provides excellent performance
across a broad spectrum of specific applications.
However, the high standards of hygiene required
in hospitals and food related industries sometimes
involve the use of harsh chemicals which can degrade
polycarbonate.
Standard Industrial Range products are identifiable
by a small symbol on the front of the plate. The ‘CR’ is
for Chemical Resistant and the numeral ‘1’ identifies
the material. If other materials come into use at a later
time for different applications, different numerals will
be used.
To address these problems, Clipsal have worked
closely with their material suppliers to develop an alloy
resistant to these chemicals and with only a minimal
reduction in impact strength.
To order Standard Industrial Range products use
standard product codes and specify Resistant White
(RW) or Resistant Soft Grey (RS). All ratings and
specifications are the same as the corresponding
product in the Standard Range.
The Standard Industrial Range is limited at this time
to 16 products and 2 colours. Resistant White (RW)
CHEMICAL RESISTANT STANDARD INDUSTRIAL RANGE
Cat. No.
Length
Width
Depth
Mounting Centres
31VA, 32VA,
33VA, 34VA,
35VA, 36VA,
31VX
115mm
73mm
11mm
84mm apart
15, 15X, 15/15,
15V, 25V
115mm
73mm
14mm
84mm apart
25, 25XA
115mm
73mm
16mm
84mm apart
449A
122mm
78mm
32mm
84mm apart
449ASD
116mm
73mm
14mm
84mm apart
31VA
A Flush Plate, with 1 x 30M mechanism in vertical format.
32VA
B Flush Plate, with 2 x 30M mechanism in vertical format.
33VA
C Flush Plate, with 3 x 30M mechanism in vertical format.
34VA
D Flush Plate, with 4 x 30M mechanism in vertical format.
35VA
E Flush Plate, with 5 x 30M mechanism in vertical format.
36VA
F Flush Plate, with 6 x 30M mechanism in vertical format.
A
B
31VA
C
D
E
F
33VA
G
H
31VX
I
31VX
G Blank Flush Plate.
15
H Single Switched Socket Outlet, 250V/10A, horizontal mounting.
15X
I
Single Switched Socket Outlet, 250V/10A, with extra switch,
horizontal mounting.
15/15
J Single Switched Socket Outlet, 250V/15A, horizontal mounting.
15V
K Single Switched Socket Outlet, 250V/10A, vertical mounting.
25V
L Twin Switched Socket Outlet, 250V/10A, single base, vertical mounting.
25
M Twin Switched Socket Outlet, 250V/10A, horizontal mounting.
25XA
N
449A
1 Gang Mounting Block, suits all flush plates with 115 x 73mm
O
and 84mm centres.
449ASD
P
J
15
K
M
251
Twin Switched Socket Outlet, 250V/10A, with extra switch,
horizontal mounting.
14mm Spacer, for standard pattern accessories, with 84mm centres,
four mounting holes in centre.
L
N
O
51
P
449ASD
CHEMICAL RESISTANT
STANDARD INDUSTRIAL RANGE (Continued)
CHEMICAL COMPARISONS
Product Type (colour)
Standard Polycarbonate Colours
Resistant White / Resistant Soft Grey
Hydrochloric 10%
EXCELLENT
EXCELLENT
Nitric 10%
EXCELLENT
EXCELLENT
POOR
POOR
POOR
GOOD
POOR
POOR
Petroleum
POOR
EXCELLENT
Lubricating Oils
POOR
EXCELLENT
Hydraulic Oil
POOR
EXCELLENT
Methane
EXCELLENT
EXCELLENT
Propane
EXCELLENT
EXCELLENT
EXCELLENT
EXCELLENT
Glycerol (Glycerin)
FAIR
GOOD
Methyl Alcohol (Methanol)
POOR
GOOD
EXCELLENT
EXCELLENT
POOR
POOR
Methyl Benzene
POOR
GOOD
Xylene
POOR
GOOD
EXCELLENT
EXCELLENT
Acetone
POOR
FAIR
Acetophenone
POOR
FAIR
Ethyl Methyl Ketone
POOR
FAIR
Acids
CHEMICAL RESISTANT STANDARD
INDUSTRIAL RANGE (Continued)
Weak Solutions
Concentrate
Sulphuric 100%
Alkalis
Weak Solutions
Sodium Hydroxide 10% (Caustic Soda)
Concentrate
Potassium Hydroxide 100%
Automotive
Solvents
Aliphatic Hydrocarbons (Alkanes)
Alcohols
Ethylene Glycol
Ethyl Alcohol (Ethanol)
Amines
Aniline
Aromatic Hydrocarbons
Ethers
Dimethyl Ethyl
Ketones
52
CHEMICAL RESISTANT
STANDARD INDUSTRIAL RANGE (Continued)
CHEMICAL COMPARISONS
Product Type (colour)
Standard Polycarbonate Colours
Resistant White / Resistant Soft Grey
EXCELLENT
EXCELLENT
EXCELLENT
EXCELLENT
EXCELLENT
EXCELLENT
EXCELLENT
EXCELLENT
Ambient
EXCELLENT
EXCELLENT
Hot> 60oC
EXCELLENT
GOOD
POOR
POOR
Miscellaneous
Detergent
Magnesium Sulphate
CHEMICAL RESISTANT STANDARD
INDUSTRIAL RANGE (Continued)
Inorganic Salts
Oxidising Agents
Weak Solution
Sodium Hypochlorite 5%
Strong Solution
Hydrogen Peroxide 30%
Water
Steam
This table should be used as a guide only. Any end user should test to evaluate the suitability of any chemical, with
any plastic.
EXCELLENT
Recommended; no adverse effects after extended exposure.
GOOD
Acceptable; minimal loss of mechanical properties after long periods of exposure.
FAIR
Marginal acceptability; loss of mechanical properties after long periods of exposure.
POOR
Not recommended for use.
53
PROTECTED SWITCHED SOCKET OUTLETS
Where power is required in Commercial and Industrial applications, the Clipsal Protected Switched Socket range is the
perfect product. Built tough to last, and in a number of configurations to suit your needs, this range stands the test
of time.
PROTECTED SWITCHED SOCKET OUTLETS
The range is available in zinc die cast and you will find matching switch outlets on page 31.
Please see the table below for details on the full range, including dimensional specifications.
PROTECTED SWITCHED SOCKET OUTLETS - 10A
Cat. No.
Length
Width
Depth
Mounting Centres
PC110,
PC110-2FR,
PC110-2RF,
PC110-N
100mm
79mm
50mm
82mm apart
PC110V-2,
PC110V-2-DP,
142mm
PC110
A
PC110-2FR
Protected Switched Socket Outlet, 250V/10A, zinc die cast,
B
2 flat, 1 round socket.
PC110-2RF
Protected Switched Socket Outlet, 250V/10A, zinc die cast,
2 round, 1 flat socket.
PC110
A
102mm
50mm
84 x 82mm apart
PC110-FR
Protected Switched Socket Outlet, 250V/10A, zinc die cast,
3 flat sockets.
PC110-N
Protected Switched Socket Outlet, 250V/10A, zinc die cast,
D
3 flat sockets, with neon.
PC110V-2
E
Protected Switched Socket Outlet, 250V/10A, zinc die cast,
3 flat sockets, vertical mount, 2 gang.
PC110V-2-DP
E
Protected Switched Socket Outlet, 250V/10A, zinc die cast,
3 flat sockets, vertical mount, 2 gang, double pole.
B
D
PC110-N
E
PC110V-2
PROTECTED SWITCHED SOCKET OUTLETS - 15A
Cat. No.
Length
Width
Depth
Mounting Centres
PC115, PC115-N
101mm
79mm
50mm
82mm apart
PC115V-2
141mm
102mm
50mm
84 x 86mm apart
PC115
A
PC115-N
Protected Switched Socket Outlet, 250V/15A, zinc die cast,
B
3 flat sockets, with neons.
PC115V-2
C
PC115
A
Protected Switched Socket Outlet, 250V/15A, zinc die cast,
3 flat sockets.
PC115-N
B
54
Protected Switched Socket Outlet, 250V/15A, zinc die cast,
3 flat sockets, vertical mount, 2 gang.
C
PC115V-2
30 SERIES SWITCHES - A CLIPSAL TRADEMARK
The Clipsal switch shape was always
destined for greatness.
It was first developed in 1963 and proved to be a
great leap forward. Unsatisfied with the hard lines of
traditional switch rockers at the time, Clipsal engineers
fashioned a more stylish alternative. The Standard
Range of Switches and Socket Outlets was the first to
use the new switch shape.
Over the years the Clipsal switch shape has undergone
very subtle changes to adapt to new technologies,
plastics and designs. But to the naked eye the original
design remains unchanged and is as strong today as
it was many years ago. Today, you’ll find the Clipsal
switch shape in dozens of different switch designs.
The 30 Series can easily be converted from vertical to
horizontal mounting by removing the mechanism and
turning it through 90°. Most switch bases fit a 22mm
diameter hole and have terminal bores of 4.1mm unless
specified otherwise.
Switch assemblies are also available with the switch
mechanisms further secured by screws located behind
the switchplate. These assemblies are designed
to prevent the mechanisms being forced out of the
switchplate which is important when the switches
are used in areas where they may be subjected to
vandalism or undue physical abuse.
The gentle curves of the overall shape are equally
proportioned to provide uncomplicated symmetry.
It is this flexibility and strength in design that has
enabled the Clipsal switch shape to adapt to just about
every Clipsal switch and socket range that has been
designed since the 1960s.
Quality Assurance surrounds everything Clipsal
does and production of the Clipsal switch shape is no
exception. Clipsal was the first Australian manufacturer
of electrical wiring accessories to achieve quality
endorsed status and is now recognised by quality
status systems around the world.
It is this commitment to quality that has given the
Clipsal switch shape its longevity. Its sleek styling was
an immediate success.
And through Clipsal’s dedication to perfection and
continuous improvement it has remained so. Indeed,
we like to think it will always be that way.
The shape of the switch dolly is a trademark
of Clipsal Australia Pty Ltd
55
30 SERIES SWITCH MECHANISMS
30 SERIES SWITCH MECHANISMS
SWITCH MECHANISMS
56
Cat. No.
Description
30M
A
30MRD
250V/10A, 1 way/2 way (with red dolly mark)- terminal bores of 4.1mm ø
B accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole.
M rating is 100.
30FLM
250V/10A, 1 way/2 way (suits fl uoro loads)- terminal bores of 4.1mm ø
A accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole. M
rating is 120.
30FLM15
250V/15A, 1 way/2 way (suits fl uoro loads)- terminal bores of 4.1mm ø
A accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole. M
rating is 90.
30RSM2
250V/15A, Rotary (2 On - 2 Off) - also suitable for 12V d.c. 15A, and audio
C and control applications. Switch positions indicated in window.
M rating is 50.
30RSM3
250V/15A, Rotary (3 On - 1 Off) - also suitable for 12V d.c. 15A, and audio
C and control applications. Switch positions indicated in window.
M rating is 50.
30MCO
A 250V/10A, Changeover, double throw (selects alternate circuits).
30MI
D
250V/10A, Intermediate - four terminals of 3.5mm ø accommodates
2 x 2.5mm² cables. Body fi ts 22mm ø hole.
30MBP
E
440V/15A, Bell press - offers facility for momentary ON or OFF
(one Looping terminal).
30MBPN
250V/15A, Illuminated bell press - offers facility for momentary ON or
F OFF. Neon is connected across terminals 1 & 4.
Alternative lamp voltages available.
30MBPR
250V/10A, Bell press rocker - offers facility for momentary ON or OFF.
G
Suitable for extra low voltage applications (one Looping terminal).
30MD
250V/10A, 1 way, double pole, single throw - terminal bores of 4.1mm ø
D accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole.
M rating is 90.
30HMD
H 250V/10A, double pole, marked “HEAT”.
30MD2
I
30MD15
250V/15A, 1 way, double pole, single throw - terminal bores of 4.1mm ø
O accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole.
M rating is 90.
30MD20
J
250V/20A, 1 way, double pole - 4 terminals of 1.5mm ø accommodate 3 x
2.5mm² cables. Body fi ts 34mm ø hole. M rating is 100.
30M15
A
250V/15A, 1 way/2 way - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole. M rating is 90.
30M15RD
250V/15A, 1 way/2 way (with red dolly mark)- terminal bores of 4.1mm ø
B accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole.
M rating is 90.
30M20
A
250V/20A, 1 way/2 way - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole. M rating is 90.
30M35
N
250V/35A, 1 way/2 way - terminal bore of 3.6mm ø & Looping terminal
bore of 3.9mm ø. M rating is 160. Marked 35A.
30TKM
250V/20A (5A fl uorescent load), 1 way/2 way, toggle key actuated K
one Looping terminal. M rating is 100.
30/1/2LM
250V/10A, 1 way (two Looping terminals) - terminal bores of 4.1mm ø
A accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole.
M rating is 100.
30/1ELM
250V/10A, 1 way (one Looping & one Earth terminal) - terminal bores of
P 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
30/1NM
250V/10A, 1 way rocker with neon indicator - neon can be wired to
L indicate ON, OFF or POWER AVAILABLE. Looping/switch terminal bores of
4.1mm ø. Body fi ts 34mm ø hole (Note: Neutral required).
30/2NM
250V/10A, 2 way rocker with neon indicator - neon can be wired to indicate
L ON, OFF or POWER AVAILABLE. Looping/switch terminal bores of 4.1mm ø.
Body fi ts 34mm ø hole (Note: Neutral not required).
30/5M
M
250V/10A, 1 way/2 way - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø hole. M rating is 100.
A
B
C
D
30M15RD
E
F
30RSM2
G
H
250V/10A, 2 Way, double pole, double throw - six terminal bores of 4.1mm ø
accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. M rating is 75.
250V/10A, 1 way/2 way (with 5 terminals - one Looping and one Earth terminal).
Terminal bore of Common, Looping and Earth of 5.3mm ø accommodates 4 x
2.5mm² cables. Terminal bore of ‘1’ and ‘2’ of 4.1mm ø accommodates 4 x 1.5mm²
or 3 x 2.5mm² cables. Body fits 26mm ø hole. M rating is 40.
30M
30MBPR
I
J
30TKM
K
L
M
30/2NM
35A
N
O
30/5M
P
Note: 30M Series products have fluorescent capacity of approximately 5A. 30MD and 30MI are not recommended for switching of multiple
fluorescent fi ttings.
30 SERIES
SWITCH MECHANISMS (Continued)
Cat. No.
Description
30N-RED
A 250V - neon indicator (RED)
30N-COLOUR
A 250V - neon indicator (OTHER COLOURS)
30 SERIES SWITCH MECHANISMS (Continued)
NEON INDICATOR MECHANISMS
A
30N-RED
Colours available are Blue, Green, Amber and Transparent. Other voltages are also available, including 6, 12, 24, 32, 48, 110 and 440. Suitable for DC loads.
To order, add voltage to Cat. No. (for example, 30N12). Neons draw 250-275mW at 240V. Note: Inductive loads occasionally cause neons to glow in OFF
position. To prevent this, place a 47kΩ, 0.5W 240V resistor across the terminals. Neutral and Active can be connected to either terminal.
Labelled Switch Mechanisms
Clipsal offers a broad range of labelled switch mechanisms for easy identification when several switches are installed
on the same switchplate or when there is any chance of confusion over the load controlled.
10A MECHANISMS - WITH MESSAGES
Cat. No.
Description
30FM
A
250V/10A, 2 way (marked “FAN”) - terminal bores of 4.1mm ø accommodate 4
x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30HM
B
250V/10A, 2 way (marked “HEAT”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
A
B
30FM
C
30EM
C
250V/10A, 2 way (marked “EXHAUST”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30LM
D
250V/10A, 2 way (marked “LIGHT”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MAM
250V/10A, 2 way (marked “MANUAL-AUTO”) - terminal bores of 4.1mm ø
E
accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30PM
250V/10A, 2 way (marked “DISPOSAL”) - terminal bores of 4.1mm ø accommodate
F
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30XM
250V/10A, 2 way (marked “WASTE”) - terminal bores of 4.1mm ø accommodate
G
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30YM
H
D
E
F
30HM
G
250V/10A, 2 way (marked “WASH”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30DNM
I
250V/10A, 2 way (marked “DAY/NIGHT”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30FAM
J
250V/10A, 2 way (marked “FAMILY”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
H
I
J
K
250V/10A, 2 way (marked “T.V.”) - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30TM
K
30COM
250V/10A, 2 way (marked “COOL”) - terminal bores of 4.1mm ø accommodate
L
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30AUM
M
250V/10A, 2 way (marked “AUTO”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30ACM
N
250V/10A, 2 way (marked “AIR CON”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30STM
250V/10A, 2 way (marked “STUDY”) - terminal bores of 4.1mm ø accommodate
O
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30FAM
L
30TM
M
N
57
O
30COM
30 SERIES
SWITCH MECHANISMS (Continued)
30 SERIES SWITCH MECHANISMS (Continued)
10A MECHANISMS - WITH MESSAGES (CONTINUED)
Cat. No.
Description
30PUM
250V/10A, 2 way (marked “PUMP”) - terminal bores of 4.1mm ø accommodate 4
P
x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30BM
Q
P
Q
250V/10A, 2 way (marked “BATH”) - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30KM
R
58
30KM
R
250V/10A, 2 way (marked “KITCHEN”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30RUM
S
250V/10A, 2 way (marked “RUMPUS”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30LOM
T
250V/10A, 2 way (marked “LOUNGE”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30DM
U
250V/10A, 2 way (marked “DINE”) - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30FNM
V
250V/10A, 2 way (marked “OFF/ON”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30AM
W
250V/10A, 2 way (marked “ALARM”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30BDM
X
250V/10A, 2 way (marked “BED”) - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30BD1M
Y
250V/10A, 2 way (marked “BED1”) - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30BD2M
Z
250V/10A, 2 way (marked “BED2”) - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30BD3M
1
250V/10A, 2 way (marked “BED3”) - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30BD4M
2
250V/10A, 2 way (marked “BED4”) - terminal bores of 4.1mm ø accommodate 4 x
1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30HLM
3
250V/10A, 2 way (marked “HI/LOW”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MSEN
4
250V/10A, 2 way (marked “SENSOR”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MOS
5
250V/10A, 2 way (marked “OUTSIDE”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MFR
6
250V/10A, 2 way (marked “FORWARD/REVERSE”) - terminal bores of 4.1mm ø
accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MFD
7
250V/10A, 2 way (marked “FRIDGE”) - terminal bores of 4.1mm ø accommodate
4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MMW
8
250V/10A, 2 way (marked “MICROWAVE”) - terminal bores of 4.1mm ø accommodate 4
x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MZ1
9
250V/10A, 2 way (marked “ZONE1”) - terminal bores of 4.1mm ø accommodate 4
x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
S
T
U
30LOM
V
W
30FNM
X
Y
Z
1
30HLM
2
3
30MSEN
4
5
6
7
30MOS
8
9
30MZ1
30 SERIES
SWITCH MECHANISMS (Continued)
10A MECHANISMS - WITH MESSAGES (CONTINUED)
Description
30MZ2
250V/10A, 2 way (marked “ZONE2”)- terminal bores of 4.1mm ø
10 accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
30MZ3
250V/10A, 2 way (marked “ZONE3”) - terminal bores of 4.1mm ø
11 accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
30MZ4
250V/10A, 2 way (marked “ZONE4”) - terminal bores of 4.1mm ø
12 accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
39M
13
250V/10A, 3 Position - marked “HI-OFF-LO”. Three terminals, 3.5mm
ø accommodate 2 x 2.5mm² cables.
39MAOM
14
250V/10A, 3 Position - marked “MAN-OFF-AUTO”. Three terminals,
3.5mm ø accommodate 2 x 2.5mm² cables.
39MSON
15
250V/10A, 3 Position - marked “SENSOR-OFF-ON”. Three terminals,
3.5mm ø accommodate 2 x 2.5mm² cables.
10
30 SERIES SWITCH MECHANISMS (Continued)
Cat. No.
11
12
30MZ2
13
14
15
39MAOM
16A MECHANISMS - WITH MESSAGES
Cat. No.
Description
30M16SEN
250V/16A, 2 way (marked “SENSOR”) - terminal bores of 4.1mm ø
A accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
30M16OS
A
B
250V/16A, 2 way (marked “OUTSIDE”) - terminal bores of 4.1mm
B ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
30M16FR
250V/16A, 2 way (marked “FORWARD/REVERSE”) - terminal bores
C of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts
22mm ø hole. M rating is 100.
30M16FD
250V/16A, 2 way (marked “FRIDGE”) - terminal bores of 4.1mm ø
D accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
30M16MW
250V/16A, 2 way (marked “MICROWAVE”) - terminal bores of 4.1mm
E ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
16A
30M16SEN
C
D
16A
E
30M16OS
20A MECHANISMS - WITH MESSAGES
Cat. No.
Description
30M20HW
250V/20A, 2 way (marked “HOT WATER SERVICE”) - terminal bores
A of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts
22mm ø hole. M rating is 100.
A
20A
20A
30M20HW
35A MECHANISMS - WITH MESSAGES
Cat. No.
Description
30M35HOB
250V/35A, 2 way (marked “HOB”) - terminal bores of 4.1mm ø
A accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
30M35OV
30M35R
A
35A
B
250V/35A, 2 way (marked “OVEN”) - terminal bores of 4.1mm ø
B accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
250V/35A, 2 way (marked “RANGE”) - terminal bores of 4.1mm ø
C accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fi ts 22mm ø
hole. M rating is 100.
35A
59
35A
C
35A
30M35OV
30 SERIES
SWITCH MECHANISMS (Continued)
10A ILLUMINATED ROCKER SWITCH MECHANISMS - WITH MESSAGES
Cat. No.
Description
A
30 SERIES SWITCH MECHANISMS (Continued)
250V/10A - 2 way inbuilt neon (marked “SENSOR”). Neon can be
30/2NMSEN A wired to indicate ON, OFF or POWER AVAILABLE. Looping/switch
terminals of bore 3.9mm ø. Body fi ts 34mm ø hole.
30/2NMOS
B
250V/10A - 2 way inbuilt neon (marked “OUTSIDE”). Neon can be
B wired to indicate ON, OFF or POWER AVAILABLE. Looping/switch
terminals of bore 3.9mm ø. Body fi ts 34mm ø hole.
30/2NMSEN
Note: Neutral is not required.
Additional messages available. Contact your CLIPSAL office for details.
Typical messages:- RANGE - HEAT/COOL - RESET - LIVING - HI/LO - SPA - DAY NIGHT - HWS - LO - OFF - ON.
DIMMER, FAN CONTROL AND SURGE FILTER MECHANISMS
Cat. No.
Description
32E450LM
C-Thru® Dimmer Mechanism, Leading Edge (suits incandescent
A lighting and low voltage lighting using iron core transformers), 220
- 240V/450W.
32E450TM
C-Thru® Dimmer Mechanism, Trailing Edge (suits incandescent
A lighting and low voltage lighting using electronic transformers), 220
- 240V/450W.
32E500FM
A C-Thru® Fan Speed Controller Mechanism, 220-240V/500W.
30POTDM
B
Dimmer Potentiometer (suits products such as 32 Series High
Powered Dimmers, 780 Series and the 761 Series).
30POTFM
C
Fan Controller Potentiometer (suits products such as 32 Series High
Powered Dimmers & 761 Series).
32E450LM
A
32E500FM
B
C
30POTFM
SURGE
PROTECTED
WHEN LIT
30SFM
32E450TM
D
D Surge Filter Mechanism - 250V 10A
30SFM
CIRCUIT IDENTIFICATION AND BLANKING PRODUCTS
Cat. No.
Description
30P
A Removable Blank Plug, to suit or blank out 30 Series aperture.
30PID
B
30PFO
C Plug, marked “FRIDGE - FREEZER ONLY”.
Removable Plug, with identification facility, supplied with tamper
proof transparent cover.
A
30P
B
C
60
30PIDA4L
30PID
D Label Sheets, 10 x A4 packet, red and white available (non-adhesive).
D
SCHEMATIC WIRING DIAGRAMS
One-Way Mechanism with Neon Indicator
NEON
30/1NM
ACTIVE
NEON TAIL
NEON TAIL
COMMON
L
C
LOAD
ACTIVE
NEUTRAL
1
LOAD
LOOP
COMMON
1
1
SCHEMATIC WIRING DIAGRAMS
To wire neon permanently “ON”
LOOP
LOOP
LOOP
NEUTRAL
ACTIVE
1
COMMON
LOAD
ACTIVE
LOAD
1
To wire neon “ON” when switch “OFF”
COMMON
To wire neon “ON” when switch “ON”
One-Way/Two-Way Mechanism with Neon Indicator
NEON
30/2NM
2
2 WAY
NEUTRAL
NEON
2
1 WAY
ACTIVE
1 WAY
COMMON
1
LOOP
2 WAY
COMMON
To wire neon permanently “ON”
1
LOOP
NEON
2
CONNECTOR
2
LOAD
ACTIVE
COMMON
LOOP
TO NEUTRAL
COMMON
1
1
LOOP
To wire neon “ON” when LOAD “ON”
2
2
LOAD
ACTIVE
TO NEUTRAL
COMMON
COMMON
61
1
LOOP
1
LOOP
To wire neon “ON” when LOAD “OFF”
SCHEMATIC WIRING DIAGRAMS (Continued)
One-Way/Two-Way Mechanisms
2-WAY
SCHEMATIC WIRING DIAGRAMS (Continued)
2
LOOP
COMMON
COMMON
LOOP
ACTIVE
1-WAY
1
30M
30M15
30M20
30M35
LOOP
LOOP
LOOP
COMMON
1
ACTIVE
1
2
30/1/2LM
30/1ELM
LOOP
COMMON
1
2-WAY
2
30/5M
30/5M15
EARTH
EARTH
COMMON
LOOP
LOOP
COMMON
1-WAY
1
1
Double Pole Mechanisms
20A
30MD2
LOAD
2-WAY
1-WAY
30MD20
ACTIVE
LOAD
1-WAY
ACTIVE
LOAD
LOAD
LOAD
ACTIVE
ACTIVE
LOAD
ACTIVE
LOAD
ACTIVE
30MD
30MD15
LOAD
62
SCHEMATIC WIRING DIAGRAMS (Continued)
Rotary Switch Mechanisms
LOAD 3
LOAD 2
ACTIVE
ACTIVE
30RSM3
(Continued)
30RSM2
LOAD 2
LOAD 1
SCHEMATIC WIRING DIAGRAMS
LOAD 1
Intermediate Mechanism
30MI
3
1
2
TO 2 WAY SWITCH
TO 2 WAY SWITCH
4
Position 1 (Up)
1
4
TO 2 WAY SWITCH
TO 2 WAY SWITCH
2
3
Position 2 (Down)
1
4
TO 2 WAY SWITCH
TO 2 WAY SWITCH
2
3
Changeover Mechanism
30MCO
CIRCUIT 2
CIRCUIT 1
CIRCUIT 2
CIRCUIT 1
63
SCHEMATIC WIRING DIAGRAMS (Continued)
Three Position Switch Mechanisms
AUTO SWITCH WIRE
SCHEMATIC WIRING DIAGRAMS (Continued)
LOOP
COMMON
39M
ACTIVE
OFF
COMMON
MANUAL SWITCH WIRE
LOOP
C-Thru® Light Dimmer/Fan Controller
32E450L Series
32E450T Series
One Way Switching
32E500F
Series
Two Way Switching
ACTIVE
1
ACTIVE
1
C
C
LOAD
LOOP
2
LOAD
LOOP
2
301/2LM SWITCH MECH
301/2LM SWITCH MECH
DIMMER OR
FAN CONTROL
DIMMER OR
FAN CONTROL
NEUTRAL
NEUTRAL
Note: All C-Thru ® dimmer plate variants are supplied with a 30/1/2LM switch mechanism. This mech is designed to be reconfigurable:
DEFAULT STATE: 1-WAY WITH TWO LOOPING TERMINALS (marked “LOOP” and “2” above).
ALTERNATE STATE: 2-WAY WITH ONE LOOPING TERMINAL (which is marked “LOOP” above).
To change over, remove terminal screws and interchange “2” and “LOOP” terminal poles/contacts. Reinsert screws and terminate wiring as usual.
High Power Dimmers
31E1000L
31E800T
One Way Switching
Two Way Switching
LOAD
64
31E1000L
31E800T
LOAD
LOAD
NEUTRAL
ACTIVE
ACTIVE
31E1000L
31E800T
LOAD
ACTIVE
2-WAY
2-WAY
LOOP
LOOP
NEUTRAL
ACTIVE
ADDITIONAL
SWITCH
SCHEMATIC WIRING DIAGRAMS (Continued)
3-Speed Capacitive Fan Controller
SCHEMATIC WIRING DIAGRAMS (Continued)
CONTROLLER
OFF
31VF3CA
31VF3CB
HIGH
COMMON
MED
ACTIVE
CAPACITOR PACK
LOW
NEUTRAL
Combined Light Switch and Time Delay for Fans
ACTIVE
NEUTRAL
31VETF
31VETF
LAMP
NEUTRAL
ACTIVE
FAN
LAMP
Note: Not suitable for use with fluorescent loads.
Push-Button Electronic Time Delay Switch
ACTIVE
NEUTRAL
31VETR
31VETR or
2031VETR
ACTIVE
LOAD
LOAD
LOOP
REMOTE
REMOTE
CONTROL
MOMENTARY
PUSH-BUTTONS
(OPTIONAL)
No Voltage Relay Switched Sockets
PUSH TO
RESET BUTTON
4
ACTIVE
E
1
2
E
A
N
15X15RZ
A
SUPPLY
CONDUCTORS
NEUTRAL
EARTH
3
PUSH
N
NO VOLT
RELAY
SWITCHED
SOCKET
65
SCHEMATIC WIRING DIAGRAMS (Continued)
Automatic Socket
NEUTRAL
10
EARTH
SCHEMATIC WIRING DIAGRAMS (Continued)
E
A
A
N
ACTIVE
N
E
Standard Pattern Mounting,
Single Gang
15
15/2
A
E
15V
N
EARTH
E
E
A
A
E
N
Inline Base
ACTIVE
N
A
NEUTRAL
N
SUPPLY
CONDUCTORS
Round Base
Switched Socket with
One Extra Switch
EARTH
E
E
A
15X
15VX
15XX
15VXX
ACTIVE
A
N
N
T
E
L
A
C
N
1
LOAD
NEUTRAL
Switched Socket with
Two Extra Switches
SUPPLY
CONDUCTORS
EARTH
E
A
E
ACTIVE
N
A
N
66
LOAD
LOOP
2
1 C
E
2
A
N
LOOP
C
LOAD
NEUTRAL
SCHEMATIC WIRING DIAGRAMS (Continued)
Standard Pattern Mounting
Twin Combination
25
25V
NEUTRAL
SUPPLY
CONDUCTORS
E
SUPPLY
CONDUCTORS
NEUTRAL
N
SCHEMATIC WIRING DIAGRAMS (Continued)
EARTH
EARTH
E
N
N
E
A
E
ACTIVE
ACTIVE
A
N
A
A
Twin Switched Sockets
with Extra Switch
NEUTRAL
25XA
EARTH
E
SUPPLY
CONDUCTORS
N
25VXA
ACTIVE
N
2
E
LOOP
TO LOAD
C
A
1
A
Double Pole Twin Switched Sockets
EARTH
E
N
25D
E
SUPPLY
CONDUCTORS
A
A
ACTIVE
N
NEUTRAL
Earth Leakage Protected
Twin Switched Sockets
EARTH
EARTH
ELECTRONIC
RESET
TO OTHER
OUTLETS
RESET
BUTTON
SUPPLY
CONDUCTORS
LOAD
25EL Series
N
N
NEUTRAL
ACTIVE
A
A
TRIP
SOLENOID
CONTINUATION
TERMINALS
ACTIVE
CONDUCTORS
67
A
N
E
A
N
E
ARCHITRAVE AND STANDARD SIZE SWITCHPLATES - MOUNTING TEMPLATES
22mm Ø
26mm
25mm
97mm
140mm
22mm Ø
26mm
124mm
113mm
27mm
22mm Ø
70mm
85mm
22mm Ø
55mm
75mm
ARCHITRAVE AND STANDARD SIZE SWITCHPLATES
- MOUNTING TEMPLATES
25mm
32mm
30
31
32mm
25mm
32A
32
32mm
33A
33
32mm
34A
34
STANDARD SIZE SWITCHPLATES
- MOUNTING TEMPLATES
73mm
Maximum
Cut-Out Size
9mm
11mm
69mm
52mm
115mm 84mm
76mm
68
MAXIMUM
CLEARANCE
AREA
STANDARD RANGE QUICK REFERENCE GUIDE
STANDARD RANGE
QUICK REFERENCE GUIDE
69
STANDARD RANGE QUICK REFERENCE GUIDE
STANDARD SIZE FLUSH SWITCHES - 250V/10A, HORIZONTAL MOUNTING, 1 WAY/2 WAY
STANDARD RANGE QUICK REFERENCE GUIDE
Cat No
31HA
Description
1 Gang Switch.
Length
115mm
Width
73mm
Depth
11mm
Mounting Centres PAGE
84mm apart
13
84mm apart
13
32HA
2 Gang Switch.
115mm
73mm
11mm
33HA
3 Gang Switch.
115mm
73mm
11mm
84mm apart
13
34HA
4 Gang Switch.
115mm
73mm
11mm
84mm apart
13
STANDARD SIZE FLUSH SWITCHES - 250V/10A, VERTICAL MOUNTING, 1 WAY/2 WAY
70
31VA
1 Gang Switch.
115mm
73mm
11mm
84mm apart
13
32VA
2 Gang Switch.
115mm
73mm
11mm
84mm apart
13
33VA
3 Gang Switch.
115mm
73mm
11mm
84mm apart
13
34VA
4 Gang Switch.
115mm
73mm
11mm
84mm apart
13
35VA
5 Gang Switch.
115mm
73mm
11mm
84mm apart
13
36VA
6 Gang Switch.
115mm
73mm
11mm
84mm apart
13
ARCHITRAVE SIZE FLUSH SWITCHES - 250V
1 Gang Switch, 10A, 1 way/2 way.
30
75mm
32mm
10mm
55mm apart
14
30D
1 Gang Switch, 10A, 1 way, double pole.
75mm
32mm
10mm
55mm apart
14
30/15
1 Gang Switch, 15A, 1 way/2 way.
75mm
32mm
10mm
55mm apart
14
30D15
1 Gang Switch, 15A, 1 way, double pole.
75mm
32mm
10mm
55mm apart
14
39
1 Gang Switch, 10A, 1 way/2 way, 3 position - Low/OFF/High.
75mm
32mm
33mm
54.3mm apart
14
30DD
1 Gang Switch, 10A, 1 way, double pole, deep plate.
77mm
32mm
18mm
55mm apart
14
32A
2 Gang Switch, 10A, 1 way/2 way.
85mm
32mm
10mm
70mm apart
14
33A
3 Gang Switch, 10A, 1 way/2 way.
113mm
32mm
10mm
97mm apart
14
34A
4 Gang Switch, 10A, 1 way/2 way.
140mm
32mm
10mm
124mm apart
14
MINIATURE ARCHITRAVE SWITCHES - 250V/10A, 1 WAY/2 WAY
1 Gang Switch.
30T
54mm
27mm
10mm
40mm apart
14
32TA
2 Gang Switch.
75mm
27mm
10mm
60mm apart
14
33TA
3 Gang Switch.
98mm
27mm
10mm
83mm apart
14
INTERMEDIATE SIZE SWITCHES - 250V/10A, 1 WAY/2 WAY (94mm x 48mm at centre)
1 Gang Switch.
95mm
31BA
48mm
10mm
55mm apart
15
32BA
2 Gang Switch.
95mm
48mm
10mm
55mm apart
15
31BLA
1 Gang Switch.
95mm
48mm
10mm
78mm apart
15
32BLA
2 Gang Switch.
95mm
48mm
10mm
78mm apart
15
LARGE FORMAT SIZE FLUSH SWITCHES - 250V/10A, 1 WAY/2 WAY, VERTICAL MOUNTING
1 Gang Switch.
116mm
31/2VA
116mm
11mm
84 x 46mm
15
32/2VA
2 Gang Switch.
116mm
116mm
11mm
84 x 46mm
15
33/2VA
3 Gang Switch.
116mm
116mm
11mm
84 x 46mm
15
34/2VA
4 Gang Switch.
116mm
116mm
11mm
84 x 46mm
15
35/2VA
5 Gang Switch.
116mm
116mm
11mm
84 x 46mm
15
36/2VA
6 Gang Switch.
116mm
116mm
11mm
84 x 46mm
15
37/2VA
7 Gang Switch.
116mm
116mm
11mm
84 x 46mm
15
38/2VA
8 Gang Switch.
116mm
116mm
11mm
84 x 46mm
15
39/2VA
9 Gang Switch.
116mm
116mm
11mm
84 x 46mm
15
STANDARD SIZE FLUSH PLATES
1 Gang.
31VH
115mm
73mm
11mm
84mm apart
16
32VH
2 Gang.
115mm
73mm
11mm
84mm apart
16
33VH
3 Gang.
115mm
73mm
11mm
84mm apart
16
34VH
4 Gang.
115mm
73mm
11mm
84mm apart
16
35VH
5 Gang.
115mm
73mm
11mm
84mm apart
16
36VH
6 Gang.
115mm
73mm
11mm
84mm apart
16
31VX
Blank Flush Plate.
115mm
73mm
11mm
84mm apart
16
31VXCB
Blank Flush Plate. With 30A terminal block.
115mm
73mm
11mm
84mm apart
16
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
ARCHITRAVE SIZE FLUSH PLATES
Cat No
31
Description
1 Gang.
Length
75mm
Width
32mm
Depth
11mm
31D
1 Gang, deep.
75mm
32mm
18mm
Mounting Centres PAGE
55mm apart
16
55mm apart
16
32
2 Gang.
86mm
32mm
11mm
70mm apart
16
33
3 Gang.
112mm
32mm
11mm
97mm apart
16
34
4 Gang.
140mm
32mm
11mm
124mm apart
16
54mm
27mm
10mm
40mm apart
17
MINIATURE ARCHITRAVE SIZE FLUSH PLATES
1 Gang.
31T
32T
2 Gang.
75mm
27mm
10mm
60mm apart
17
33T
3 Gang.
98mm
27mm
10mm
83mm apart
17
INTERMEDIATE SIZE FLUSH PLATES
1 Gang.
31B
95mm
48mm
10mm
55mm apart
17
32B
2 Gang.
95mm
48mm
10mm
55mm apart
17
31BL
1 Gang, with large mounting centres.
95mm
48mm
10mm
78mm apart
17
32BL
12 Gang, with large mounting centres.
95mm
48mm
10mm
78mm apart
17
LARGE FORMAT SIZE FLUSH PLATES - VERTICAL MOUNTING
1 Gang.
31/2V
116mm
116mm
11mm
84mm x 46mm
17
32/2V
2 Gang.
116mm
116mm
11mm
84mm x 46mm
17
33/2V
3 Gang.
116mm
116mm
11mm
84mm x 46mm
17
34/2V
4 Gang.
116mm
116mm
11mm
84mm x 46mm
17
35/2V
5 Gang.
116mm
116mm
11mm
84mm x 46mm
17
36/2V
6 Gang.
116mm
116mm
11mm
84mm x 46mm
17
37/2V
7 Gang.
116mm
116mm
11mm
84mm x 46mm
17
38/2V
8 Gang.
116mm
116mm
11mm
84mm x 46mm
17
39/2V
9 Gang.
116mm
116mm
11mm
84mm x 46mm
17
31/2VX
2 Gang Blank Flush Plate.
116mm
116mm
11mm
84mm x 46mm
17
31/3VX
3 Gang Blank Flush Plate.
162mm
115mm
11mm
84mm x 46mm
17
SKIRTING SIZE FLUSH PLATES
1 Gang.
31BMF
99mm
45mm
18mm
78mm apart
18
32BMF
2 Gang.
99mm
45mm
18mm
78mm apart
18
35BMF
5 Gang.
156mm
45mm
18mm
136mm apart
18
24mm
50mm
18
JUNCTION BOX MOUNTED FLUSH PLATE
Round Plate, suits J-Box Mounting (70mm diameter).
31VR
70mm Ø
TELEPHONE / DATA OUTLET PLATE
Data Outlet Plate, with Cat 3 RJ45 socket.
31VRJ
115mm
73mm
11mm
84mm
18
IP54 RATED WEATHERPROOF FLUSH SWITCH
1 Gang Weatherproof Switch Plate, (IP54 rated).
31VHWP
115mm
73mm
11mm
84mm apart
18
84mm apart
20
84mm apart
20
C-THRU® LIGHT DIMMERS
11mm - plate
13mm - knob
30mm - wall recess
11mm - plate
13mm - knob
30mm - wall recess
32E450L
C-Thru® Light Dimmer, Leading Edge, 220-240V/450W.
115mm
73mm
32E450T
C-Thru® Light Dimmer, Trailing Edge, 220-240V/450W.
115mm
73mm
32E450LM
C-Thru® Light Dimmer Mechanism, Leading Edge, 220-240V/450W.
22mm
22mm
13mm - plate
41mm - wall recess
N/A
20
22mm
22mm
13mm - plate
41mm - wall recess
N/A
20
84mm apart
20
84mm apart
20
84mm apart
20
84mm apart
20
32E450TM
C-Thru® Light Dimmer Mechanism, Leading Edge, 220-240V/450W.
HIGH POWER SERIES LIGHT DIMMERS
31E800T
Trailing Edge Light Dimmer, 250V/800VA (suits electronic transformers).
115mm
73mm
31E1000L
Leading Edge Light Dimmer, 2 50V/1000VA (suits incandescent & iron core trans.).
115mm
73mm
32/1000
Incandescent & Low Voltage Remote Light Dimmer, 250V/1000VA.
115mm
73mm
32/2400
Incandescent & Low Voltage Remote Light Dimmer, 250V/2400VA.
115mm
73mm
15mm - plate
11mm - knob
30mm - wall recess
15mm - plate
11mm - knob
30mm - wall recess
11mm - plate
13mm - knob
30mm - wall recess
11mm - plate
13mm - knob
30mm - wall recess
71
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
FILTER MODULE
Cat No
32EIND
Description
Inductor Filter Module, for use with electronic transformers
Length
96m
Width
70mm
Depth
48mm
Mounting Centres PAGE
73mm apart
20
C-THRU® FAN SPEED CONTROLLER
32E500F
C-Thru® Fan Controller, 220-240V/500W.
115mm
73mm
11mm - plate
13mm - knob
30mm - wall recess
84mm apart
20
32E500FM
C-Thru® Fan Controller Mechanism, 220-240V/500W.
22mm
22mm
13mm - plate
41mm - wall recess
N/A
20
FAN SPEED CONTROLLER FOR “AIRFLOW” ACES36AL & ACES48AL
31VF3CA
3 Speed Fan Controller, 100VA, suitable for use with Airflow ACES36AL & ACES48AL.
115mm
73mm
11mm - plate
14mm - knob
40mm - wall recess
84mm apart
21
31VF3CB
3 Speed Fan Controller, 100VA, suitable for Airflow ACES56AL and AFLR48.
115mm
73mm
11mm - plate
14mm - knob
40mm - wall recess
84mm apart
21
ELECTRONIC TIMER CONTROLS - 250V/10A
254 minutes, 2 wire.
31VETR
115mm
73mm
11mm
84mm apart
21
31VETR3
15 hours, 3 wire.
115mm
73mm
11mm
84mm apart
21
31VETF
10 minutes, fans/lights.
115mm
73mm
11mm
84mm apart
21
PNEUMATIC TIME DELAY SWITCHES
Time Delay Switch.
319
115mm
73mm
11mm
84mm apart
22
319RA
Time Delay Switch, reverse action.
115mm
73mm
11mm
84mm apart
22
319N
Time Delay Switch with Neon.
115mm
73mm
11mm
84mm apart
22
319HP
Time Delay Switch, Weatherproof/Hose Proof.
115mm
73mm
11mm
84mm apart
22
319X
Time Delay Switch with Extra Switch.
115mm
73mm
11mm
84mm apart
22
121mm
ANALOGUE TIMER CONTROLS
24 Hour Timer, Single Power Outlet, 250V/10A (with safety shutter).
TC15/24
79mm
42mm
84mm apart
22
TC15/15/24 24 Hour Timer, Single Socket Outlet, 250V/15A (with safety shutter).
TC15/15/7D 7 Day Timer, Single Power Outlet, 250V/15A (with safety shutter).
121mm
79mm
42mm
84mm apart
22
121mm
79mm
42mm
84mm apart
22
TC32V1
1 Hour Timer, Flush Switch, 250V/15A.
115mm
73mm
62mm
84mm apart
22
TC32V24
24 Hour Timer, Flush Switch, 250V/15A.
115mm
73mm
62mm
84mm apart
22
TC32V7D
7 Day Timer, Flush Switch, 250V/15A.
115mm
73mm
62mm
84mm apart
22
TC475/24
24 Hour Timer, Portable Dual Switch Socket.
160mm
130mm
120mm
N/A
22
115mm
74mm
50mm
84mm apart
23
115mm
73mm
84mm apart
23
SWITCH MULTIPLIERS
Switch Multiplier, 250V/10A, 1 way.
780/1
96mm
70mm
48mm
73mm apart
23
780/2
Switch Multiplier, 250V/10A, 2 way.
96mm
70mm
48mm
73mm apart
23
780K1
Switch Multiplier, 250V/10A, 1 way (with 2 gang architrave switch assembly).
96mm
70mm
48mm
73mm apart
23
780K2
Switch Multiplier Mechanism, 250V/10A, 2 way.
96mm
70mm
48mm
73mm apart
23
780M
Switch Multiplier Mechanism, 250V/10A.
N/A
N/A
N/A
N/A
23
780A2M
Switch Multiplier Mechanism (suits 2 loads 2 way type A bias).
N/A
N/A
N/A
N/A
23
780B2M
Switch Multiplier Mechanism (suits 2 loads 2 way type B bias).
N/A
N/A
N/A
N/A
23
UNDER VOLTAGE RELAYS
Single Power Outlet, 250V/15A (with no volt relay and reset switch).
15X15RZ
115mm
73mm
11mm
84mm apart
24
15XRZ
Single Power Outlet, 250V/10A (with no volt relay and reset switch).
115mm
73mm
11mm
84mm apart
24
32VRZ
No Volt Relay and Reset Switch, 250V/10A (standard size).
115mm
73mm
11mm
84mm apart
24
32VRZ15
No Volt Relay and Reset Switch, 250V/15A (standard size).
115mm
73mm
11mm
84mm apart
24
SUNSET SWITCH
Sunset Switch, 250V/10A, 16 hours, 2 wire, IP56 (standard size).
31VSSR
BOOSTER ELEMENT RELAY
31VBER
72
Booster Relay for Solar Hot Water Element, 250V/15A.
plate - 16mm
button - 4.5
wall recess - 29mm
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
KEY TAG TYPE SWITCHES - 250V a.c.
Cat No
36VKT3N
Description
Key Tag Switch, suits 3x20A, 1/2way circuit with neon.
Length
115mm
Width
73mm
Depth
11mm
36VKT3NX
Key Tag Switch, suits 3x20A, 1/2way circuit, neon, extra 250V a.c. 10A switch mech.
115mm
73mm
11mm
Mounting Centres PAGE
84mm apart
25
84mm apart
25
36VKT4
Key Tag Type Switch, suits 4x20A, 1/2way circuits.
115mm
73mm
11mm
84mm apart
25
36VKT4X
Key Tag Type Switch, suits 4x20A, 1/2way circuits, extra 10A 250V a.c. switch mech.
115mm
73mm
11mm
84mm apart
25
35VKT
Key Tag, suits 35VKT series switches.
120mm
45mm
5mm
N/A
25
2034VKT
Short Key Tag, suits 2034VKT series switches.
92mm
40mm
7mm
N/A
25
KEY TAG ONLY
KEY OPERATED SWITCHES - 250V, 20A/16AX
Key Operated Switch, 1 way (locks in Off position).
31VK1
115mm
73mm
11mm
84mm apart
25
31VK1/2
115mm
73mm
11mm
84mm apart
25
Key Operated Switch, 2 way (locks in Off position).
31VK2
Key Operated Switch, 1 way (locks in On and Off position).
115mm
73mm
11mm
84mm apart
25
31VK2/2
Key Operated Switch, 2 way (locks in On and Off position).
115mm
73mm
11mm
84mm apart
25
COMMON KEYED SWITCHES
Key Operated Switch, 250V 20A/16AX, 1 way (locks in Off position).
31VK1CK
115mm
73mm
11mm
84mm apart
25
31VK1/2CK
115mm
73mm
11mm
84mm apart
25
Key Operated Switch, 250V 20A/16AX, 2 way (locks in Off position).
31VK2CK
Key Operated Switch, 250V 20A/16AX, 1 way (locks in On and Off position).
115mm
73mm
11mm
84mm apart
25
31VK2/2CK
Key Operated Switch, 250V 20A/16AX, 2 way (locks in On and Off position).
115mm
73mm
11mm
84mm apart
25
CEILING SWITCHES
Ceiling Switch, 250V/15A, 1 way.
306
52mm Ø
71mm
39mm
26
342
Ceiling Switch, 250V/10A, 1 way.
52mm Ø
71mm
39mm
26
343
Ceiling Switch, 250V/10A, 2 way.
52mm Ø
71mm
39mm
26
346
Ceiling Switch, 250V/15A, 1 way.
52mm Ø
71mm
39mm
26
WILCO CEILING SWITCH
Ceiling Switch, pull cord, 10A, double pole with indicator.
PC1
57mm
45mm
18mm
30mm x 28mm
26
FOOT OPERATED SWITCH
Foot Operated Switch, 250V/10A, double pole.
360
93mm
55mm
29mm
68 x 18mm apart
26
AMERICAN STYLE FLUSH SWITCHES AND PLATES - INDIRECT MOUNTING
1 Gang Switch Plate.
321
115mm
70mm
8mm
60mm apart
27
321R
Switch Plate, suits one socket.
115mm
70mm
8mm
60mm apart
27
322/1R
Switch Plate, suits 1 switch and 1 socket.
116mm
116mm
8mm
320
Switch Mechanism, 250V a.c./10A, 1 way.
93mm
35mm
60 x 46mm
27
84mm apart
27
320/15
Switch Mechanism, 250V a.c./15A, 1way.
93mm
35mm
84mm apart
27
DC3
Flush Switch, 5A, 3 terminal, 1 way, d.c. (with mounting lugs).
93mm
35mm
36mm
84mm apart
27
DC3-SPDT
Flush Switch, 5A, 3 terminal, single pole/double throw, d.c. (with mounting lugs).
93mm
35mm
36mm
84mm apart
27
Flush Switch, 10A, 1 way.
WSW110
WSW110/TW Flush Switch, 10A, 2 way.
Flush Switch, 16A, 1 way.
WSW116
93mm
35mm
32mm
84mm apart
27
93mm
35mm
32mm
84mm apart
27
93mm
35mm
32mm
84mm apart
27
WSW116/TW Flush Switch, 16A, 2 way.
Flush Switch, 10A, intermediate (with mounting lugs).
FS169/I
93mm
35mm
32mm
84mm apart
27
93mm
35mm
22mm
84mm apart
27
FS169/15DPDT Flush Switch, 15A, intermediate, double pole/double throw (with mounting lugs).
93mm
35mm
22mm
84mm apart
27
WILCO SURFACE SWITCH
SS165/15/2 Surface Switch, 15A, 2 way, 3 terminal, screw secured cover (52mm diameter).
52mm Ø
17mm
36mm apart
28
SURFACE SWITCHES - 250V
Surface Switch, 10A, 1 way, 3 terminal.
362
60mm Ø
19mm
48mm apart
28
362/15
Surface Switch, 15A, 1 way, 3 terminal.
60mm Ø
19mm
48mm apart
28
363
Surface Switch, 10A, 2 way, 4 terminal.
60mm Ø
19mm
48mm apart
28
389
Surface Switch, 25A a.c., 32V d.c., 1 way.
61mm Ø
27mm
43mm apart
28
BELL PRESS
98
Bell Press, illuminated.
60mm
25mm
19mm
48mm apart
28
73
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
WILCO PUSH BUTTON SWITCHES - WITH COLLAR AND LOCKNUT
Cat No
Description
74
Length
Width
Depth
N/A
28
N/A
28
PBS136
2A, single pole.
28mm
15mm
28mm
(Room protrusion - 18mm)
PBS236
2A double pole.
28mm
15mm
34mm
(Room protrusion - 18mm)
PUSH BUTTON WEATHERPROTECTED 1P53 SURFACE SWITCHES - 1 GANG, SINGLE POLE
60mm
35mm
WPBSW110 10A, 1 way/2 way.
60mm
35mm
WPBSW116 16A, 1 way/2 way.
CIRCUIT IDENTIFICATION PRODUCTS
Removable Blank Plug, suits 30 series.
21mm
21mm
30P
Plug, marked “FRIDGE - FREEZER ONLY”.
21mm
21mm
30PFO
30 Series ID Circuit Plug, tamper proof.
21mm
21mm
30PID
Label Sheets, 10 x A4 packet (RD, BU, GR, YL, WE colours available).
N/A
N/A
30PIDA4L
Cap, suits switch plate screw recesses.
8mm Ø
9
Identi, caps for circuit identification.
8mm Ø
9SERIES
MOUNTING ACCESSORIES
Screw Mounting Earthing Terminal.
6mm
N/A
ET30
Mounting Clip with Moulded Surround.
45mm
27mm
B30GFZ
Mounting Clip Mechanism, suits 1mm thick sheet.
29mm
29mm
F30Z1
Mounting Clip Mechanism, suits 1.5mm thick sheet.
29mm
29mm
F30Z1.5
Mounting Clip Mechanism, suits 2mm thick sheet.
29mm
29mm
F30Z2
Mounting Clip Mechanism, suits 4m thick sheet.
29mm
29mm
F30Z4
Three Gang Mounting Flange.
162mm
116mm
31/3F
CABLE CONNECTION ACCESSORIES
Blank Plate with 30A Connector Block.
115mm
73mm
31VXCB
115mm
73mm
32VA15/38TB 30M15 Mech and 38TB Terminal Block in Standard Size Plate.
22mm Ø
Grommet, suits up to 2.5mm2 ordinary duty flex cord.
38
Grommet, suits up to 1.5mm2 ordinary duty flex cord.
22mm Ø
38A
Grommet, suits up to 1mm2 ordinary duty flex cord.
22mm Ø
38X
Grommet, suits figure 8 two core flex cord.
22mm Ø
38Y
Grommet, suits up to 0.75mm2 light duty flex cord.
22mm Ø
38Z
Grommet, suits up to 2.5mm2 ordinary duty with clamp.
25mm
21mm
38HD
Cord Outlet Terminal Block with Grommet, suits 30 Series plates.
32mm
22mm
38TB
PROTECTED SWITCH - 250V, MOULDED, 1 WAY/2 WAY
10A.
75mm
46mm
PSM110
15A.
75mm
46mm
PSM115
PROTECTED SWITCHES - 250V, 10A, ZINC DIE CAST
Single pole.
79mm
51mm
PS110
Single pole, d.c. operation.
79mm
51mm
PS110-DC
Double pole.
79mm
51mm
PS110-DP
Single pole, intermediate.
79mm
51mm
PS110-I
Single pole, with neon.
79mm
51mm
PS110-N
Single pole, 2 way.
79mm
51mm
PS110-TW
Single pole, two gang.
101mm
79mm
PS110-2
Double pole, two gang.
101mm
79mm
PS110-2DP
Single pole, two gang, intermediate.
101mm
79mm
PS1102I
PROTECTED SWITCHES - 250V, 16A, ZINC DIE CAST, SINGLE POLE
Single pole.
80mm
51mm
PS116
Two gang.
80mm
51mm
PS116/TW
2 way.
101mm
80mm
PS116/2
Mounting Centres PAGE
32mm
32mm
28
28
10mm
10mm
7mm
N/A
5mm
5mm
N/A
N/A
N/A
29
29
29
29
29
29
N/A
11mm
N/A
N/A
N/A
N/A
11mm
N/A
24mm apart
N/A
N/A
N/A
N/A
92mm apart
29
29
29
29
29
29
29
11mm
11mm
84mm apart
84mm apart
N/A
N/A
N/A
N/A
N/A
N/A
N/A
30
30
30
30
30
30
30
30
30
51mm
51mm
69mm apart
69mm apart
31
31
50mm
50mm
50mm
50mm
50mm
50mm
50mm
50mm
50mm
37mm apart
37mm apart
37mm apart
37mm apart
37mm apart
37mm apart
82mm apart
82mm apart
82mm apart
31
31
31
31
31
31
31
31
31
50mm
50mm
50mm
38mm apart
38mm apart
82mm apart
31
31
31
30mm
STANDARD SIZE SINGLE AUTOMATICALLY SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Cat No
Description
Length
10A, single pole.
115mm
10
10A, double pole.
115mm
10D
10A, double pole with safety shutters.
115mm
10DS
10A, double pole with safety shutters & neon.
115mm
10DN
10A, round earth, double pole with safety shutter.
115mm
10DLS
15A, double pole with safety shutter.
115mm
10D15S
10A, double pole flush weather proof.
93mm
10DWP
15A, double pole flush weather proof.
93mm
10DWP15
10A, double pole with flap, IP34 rating.
101mm
415VF
15A, double pole with flap, IP34 rating.
101mm
415VF15
10A, single pole with security flap.
115mm
10PL
STANDARD SIZE TWIN AUTOMATICALLY SWITCHED SOCKET OUTLETS - 10A, HORIZONTALLY MOUNTED
Single pole.
115mm
20
Double pole.
115mm
20D
Double pole with safety shutters.
115mm
20DS
Double pole with safety shutters & neons.
115mm
20DN
Round earth, double pole & safety shutters.
115mm
20DLS
SKIRTING MOUNTED SINGLE AUTOMATICALLY SWITCHED SOCKET OUTLET
Single Auto Switched Socket Outlet, skirting mounted, 10A, single pole, 99 x 45mm at centre.
95mm
11
SKIRTING MOUNTED TWIN AUTOMATICALLY SWITCHED SOCKET OUTLETS - 10A
Single pole.
125mm
11/2
Single pole to suit ducting.
125mm
11/2MF
Single pole, safety shutters, neons, suits ducting.
125mm
11/2MFN
AUTOMATICALLY SWITCHED SOCKET OUTLETS - SINGLE
10A, single pole.
97mm
10M
10A, double pole.
97mm
10MD
10A, double pole with safety shutter.
97mm
10MDS
10A, round earth, double pole with safety shutter.
97mm
10MDLS
15A, double pole with shutter.
97mm
10MD15S
20A, double pole.
97mm
10MD20
SPECIAL PURPOSE AUTOMATICALLY SWITCHED SOCKET OUTLETS
Width
73mm
73mm
73mm
73mm
73mm
73mm
82mm
82mm
80mm
80mm
73mm
Depth
16mm
16mm
16mm
16mm
16mm
16mm
12mm
12mm
37mm
37mm
22mm
73mm
73mm
73mm
73mm
73mm
16mm
16mm
16mm
16mm
16mm
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
34
34
34
34
34
45mm
17mm
78mm apart
34
50mm
50mm
50mm
17mm
17mm
17mm
104mm apart
104mm apart
104mm apart
34
34
34
43mm
43mm
43mm
43mm
43mm
43mm
29mm
29mm
29mm
29mm
29mm
29mm
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
35
35
35
35
35
35
See mounting detail
Pg. 38
See mounting detail
Pg. 38
35
Mounting Centres PAGE
84mm apart
33
84mm apart
33
84mm apart
33
84mm apart
33
84mm apart
33
84mm apart
33
70 x 54mm
33
70 x 54mm
33
76 x 65mm
33
76 x 65mm
33
84mm apart
33
10MP
Single Auto Switched Socket Outlet Mechanism, 10A, single pole. Fascia - 42mm Ø.
42mm
43mm
10MDP
Single Auto Switched Socket Outlet Mechanism, 10A, double pole. Fascia - 42mm Ø.
42mm
43mm
33mm
(Room protrusion - 3.5mm)
33mm
(Room protrusion - 3.5mm)
10MDPL
Single Auto Switched Socket Outlet Mechanism, 10A, round earth, double pole.
Fascia - 42mm Ø.
42mm
43mm
33mm
(Room protrusion - 3.5mm)
See mounting detail
Pg. 38
35
10MDP15
Single Auto Switched Socket Outlet Mechanism, 15A, double pole. Fascia - 42mm Ø.
42mm
43mm
33mm
(Room protrusion - 3.5mm)
See mounting detail
Pg. 38
35
33mm
33mm
33mm
33mm
33mm
34mm
31mm
31mm
31mm
50mm apart
50mm apart
50mm apart
50mm apart
50mm apart
N/A
64mm apart
64mm apart
64mm apart
36
36
36
36
36
36
36
36
36
29mm
29mm
N/A
N/A
37
37
15mm
15mm
84mm apart
84mm apart
37
37
15mm
15mm
98mm apart
98mm apart
37
37
Single Auto Switched Socket Outlet Mechanism, 10A, double pole.
60mm
42mm
10MDLB
Single
Auto
Switched
Socket
Outlet
Mechanism,
10A,
double
pole
with
safety
shutter.
60mm
42mm
10MDSLB
Single Auto Switched Socket Outlet Mechanism, round earth, double pole, safety shutter.
60mm
42mm
10MDLSLB
60mm
42mm
10MD15SLB Single Auto Switched Socket Outlet Mechanism, 15A, double pole with safety shutter.
Single Auto Switched Socket Outlet Mechanism, 20A, double pole.
60mm
42mm
10MD20LB
GEC Miniplug Mechanism, 10A, double pole with safety shutter.
46mm
46mm
G10MDS
GEC AF Series Mechanism, 10A, double pole with safety shutter.
74mm Ø
G10FMDS
74mm Ø
G10FMD15S GEC AF Series Mechanism, 15A, double pole with safety shutter.
GEC AF Series Mechanism, 10A, round earth with safety shutter.
74mm Ø
G10FMDLS
SKIRTING MOUNTED SIDE CONNECTING SOCKET OUTLETS - 250V/10A, SINGLE POLE
Single Auto Switched Socket Outlet.
63mm
43mm
12M
Single Auto Switched Socket Outlet.
90mm
43mm
17M
STANDARD SIZE SINGLE TOGGLE SWITCHED SOCKET OUTLETS - 250V/20A, HORIZONTALLY MOUNTED
Single Switched Socket Outlet, toggle switch, single pole.
115mm
70mm
42/20
Single Switched Socket Outlet, toggle switch, single pole with safety shutter & neon.
115mm
70mm
42/20N
SINGLE TOGGLE NARROW ARCHITRAVE SIZE SWITCHED SOCKET OUTLETS - 250V/10A, VERTICALLY MOUNTED
Single pole.
115mm
48mm
40
Double pole.
115mm
48mm
40D
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
35
75
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
UNSWITCHED SOCKET OUTLETS- SINGLE
Cat No
Description
Length
Width
Depth
405
96mm
42mm
33mm
(Room protrusion - 3.5mm)
84mm apart
38
Mounting Centres PAGE
405/32
32V/15A, 2 pin polarised, extra low voltage.
96mm
42mm
33mm
(Room protrusion - 3.5mm)
84mm apart
38
415
250V/10A, 3 pin.
96mm
42mm
33mm
(Room protrusion - 3.5mm)
84mm apart
38
84mm apart
38
84mm apart
38
415L
250V/10A, 3pin, round earth pin.
96mm
42mm
33mm
(Room protrusion - 3.5mm)
415/110
110V/10A, 3 pin, 2 round live pins.
96mm
42mm
33mm
(Room protrusion - 3.5mm)
42mm
33mm
(Room protrusion - 3.5mm)
84mm apart
38
38
415/15
250V/15A, 3 pin.
96mm
415MP
250V/10A, 3 pin, panel mount.
43mm
42mm
33mm
(Room protrusion - 3.5mm)
415MP15
250V/15A, 3 pin, panel mount.
43mm
42mm
33mm
(Room protrusion - 3.5mm)
42mm
33mm
(Room protrusion - 3.5mm)
See mounting detail
Pg. 38
See mounting detail
Pg. 38
See mounting detail
Pg. 38
24mm
24mm
24mm
50mm apart
50mm apart
50mm apart
38
38
38
42mm
42mm
42mm
42mm
42mm
28mm
28mm
28mm
28mm
28mm
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
39
39
39
39
39
59mm
59mm
59mm
35mm
35mm
35mm
25mm
25mm
25mm
11mm
11mm
11mm
84mm apart
84mm apart
84mm apart
N/A
N/A
N/A
39
39
39
39
39
39
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
14mm
14mm
14mm
14mm
14mm
14mm
33mm
14mm
14mm
14mm
14mm
14mm
14mm
14mm
14mm
14mm
14mm
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
41
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
16mm
16mm
16mm
16mm
16mm
16mm
16mm
16mm
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
42
42
42
42
42
42
42
42
415MPL
76
250V/10A, 2 pin parallel.
S250V/10A, 3 pin, round earth, panel mount.
43mm
250V/10A, 3 pin, suits round J-Box.
66mm Ø
426
250V/10A, 3 pin, round earth pin, suits round J-Box.
66mm Ø
426L
250V/15A, 3 pin, suits round J-Box.
66mm Ø
426/15
WILCO SOCKET OUTLETS (GREY ONLY) - SINGLE
250V/10A, 3 flat pins.
96mm
FOS106
250V/10A, 3 pins, round earth pin.
96mm
FOS106R
96mm
FOS106/2R 110V/10A, 3pins, 2 round live pins.
96mm
FOS106/15 250V/15A, 3 flat pins.
2 flat polarised, extra low voltage.
96mm
FOS105T
ELECTRIC CLOCK CONNECTION ACCESSORIES - 250V
Clock Point Recessed Socket, 15A, 50Hz, 3 pin.
106mm
408/3
Clock Point Recessed Socket, 3 pin, suitable for other than 50Hz.
106mm
408/3A
Clock Point Recessed Socket, 5A, 4 pin.
106mm
408/4
Clock Point Plug, 5A, 50Hz, 3 pin.
48mm
409/3
Clock Point Plug, 3 pin, suitable for other than 50Hz.
48mm
409/3A
Clock Point Plug, 5A, 50Hz, 4 pin.
48mm
409/4
STANDARD SIZE SINGLE SWITCHED SOCKET OUTLETS - 250V, HORIZONTALLY MOUNTED
10A.
115mm
15
10A with safety shutter.
115mm
15S
10A with safety shutter and neon.
115mm
15N
10A, double pole.
115mm
15D
15, double pole.
115mm
15D15
S10A, double pole, with safety shutter & neon.
115mm
15DN
10A, double pole, deep plate.
115mm
15DD
10A, double pole with extra switch.
115mm
15DX
15A.
115mm
15/15
15A with safety shutter.
115mm
15/15S
15A with safety shutter and neon.
115mm
15/15N
10A, round earth pin.
115mm
15L
10A, round earth pin with safety shutter and neon.
115mm
15LN
S10A with extra switch.
115mm
15X
10A with extra switch and safety shutter.
115mm
15XS
10A with extra switch, safety shutter and neon.
115mm
15XN
10A with two extra switches.
115mm
15XX
STANDARD SIZE TWIN SWITCHED SOCKET OUTLETS - 250V, HORIZONTALLY MOUNTED
10A.
115mm
25
10A with safety shutters.
115mm
25S
10A with safety shutters and neons.
115mm
25N
10A, double pole.
115mm
25D
15A, double pole.
115mm
25D15
15A.
115mm
25/15
15A with safety shutters.
115mm
25/15S
15A with safety shutters and neons.
115mm
25/15N
38
38
STANDARD SIZE TWIN SWITCHED SOCKET OUTLETS - 250V, HORIZONTALLY MOUNTED (continued)
Cat No
Description
Length
Width
15 & 10A.
115mm
73mm
25/1510
10A, round earth pin.
115mm
73mm
25L
10A, with extra one way switch.
115mm
73mm
25X
10A, extra one way switch and shutters.
115mm
73mm
25XS
10A, marked with “FAN” on extra switch.
115mm
73mm
MF25X
10A, marked with “LIGHT” on extra switch.
115mm
73mm
ML25X
10A with removable extra switch.
115mm
73mm
25XA
10A, removable extra switch, safety shutters & neons.
115mm
73mm
25XAN
10A, double pole & removable extra switch.
115mm
73mm
25XD
STANDARD SIZE SINGLE SWITCHED SOCKET OUTLETS - 250V, VERTICALLY MOUNTED
10A.
115mm
73mm
15V
10A with safety shutter.
115mm
73mm
15VS
10A with safety shutter and neon.
115mm
73mm
15VN
15A.
115mm
73mm
15V15
15A with safety shutter and neon.
115mm
73mm
15V15N
10A with removable extra switch.
115mm
73mm
15VX
10A with safety shutters and removable extra switch.
115mm
73mm
15VXS
10A with safety shutters, neon and removable extra switch.
115mm
73mm
15VXN
10A with two removable extra switches.
115mm
73mm
15VXX
STANDARD SIZE TWIN SWITCHED SOCKET OUTLETS - 250V/10A, VERTICALLY MOUNTED
Two piece base.
115mm
73mm
15/2V
With safety shutters, two piece base.
115mm
73mm
15/2VS
With neons and safety shutters, two piece base.
115mm
73mm
15/2VN
Double pole, two piece base.
115mm
73mm
15D2V
Double pole with deep plate, two piece base.
133mm
83mm
15DD2V
Twin Switched Socket Outlet, 250V/10A.
115mm
73mm
25V
With removable extra switch.
115mm
73mm
25VXA
SKIRTING MOUNTED SINGLE SWITCHED SOCKET OUTLETS - 250V
10A with safety shutter.
98mm
45mm
16
10A with safety shutter and neon.
98mm
45mm
16N
10A, in line terminals.
98mm
45mm
16F
15A.
98mm
45mm
16/15
10A with extra switch.
125mm
45mm
16X
10A, double pole.
98mm
45mm
16D
SKIRTING MOUNTED TWIN SWITCHED SOCKET OUTLETS - 250V
10A.
168mm
45mm
16/2
10A with safety shutters.
168mm
45mm
16/2S
10A with neons & safety shutters.
168mm
45mm
16/2N
10A with straight sides.
168mm
45mm
16/2F
10A, suits ducting.
156mm
44mm
16/2MF
156mm
44mm
16/2MF1510 T15A &10A, suits ducting.
10A, double pole.
156mm
44mm
16/2MFD
INTERMEDIATE SINGLE SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Single Switched Socket Outlet, intermediate size, 250V/10A, horizontal.
115mm
61mm
14
LARGE FORMAT SIZE SINGLE SWITCHED SOCKET OUTLETS - 250V/10A, HORIZONTALLY MOUNTED
Single pole.
115mm
115mm
15/2
Single pole with safety shutter.
115mm
115mm
15/2S
Single pole with safety shutter & neon.
115mm
115mm
15/2N
LARGE FORMAT SIZE TWIN SWITCHED SOCKET OUTLETS - 250V/10A, (115mm x 115mm), VERTICALLY MOUNTED
Twin Switched Socket Outlet.
115mm
115mm
25/2V
With safety shutters.
115mm
115mm
25/2VS
With neons and safety shutters .
115mm
115mm
25-2VN
LARGE FORMAT SIZE TWIN SWITCHED SOCKET OUTLETS - HORIZONTALLY MOUNTED
Twin Switched Socket Outlet, large format, 250V/10A.
145mm
86mm
23
Depth
16mm
16mm
16mm
16mm
16mm
16mm
16mm
16mm
16mm
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
Mounting Centres PAGE
84mm apart
42
84mm apart
42
84mm apart
42
84mm apart
42
84mm apart
42
84mm apart
42
84mm apart
42
84mm apart
42
84mm apart
42
14mm
14mm
14mm
14mm
14mm
14mm
14mm
14mm
14mm
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
43
43
43
43
43
43
43
43
43
14mm
14mm
14mm
14mm
37mm
16mm
16mm
84mm apart
84mm apart
84mm apart
84mm apart
97mm apart
84mm apart
84mm apart
43
43
43
43
43
43
43
14mm
14mm
14mm
14mm
14mm
14mm
78mm apart
78mm apart
78mm apart
78mm apart
104mm apart
78mm apart
44
44
44
44
44
44
13mm
13mm
13mm
13mm
18mm
18mm
18mm
145mm apart
145mm apart
145mm apart
145mm apart
136mm apart
136mm apart
136mm apart
44
44
44
44
44
44
44
13mm
84mm apart
44
14mm
14mm
14mm
84 x 46mm
84 x 46mm
84 x 46mm
45
45
45
11mm
11mm
11mm
84 x 46mm
84 x 46mm
84 x 46mm
45
45
45
15mm
120mm apart
45
77
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
78
PROTECTED SOCKET OUTLETS
Cat No
Description
Single Switched Socket Outlet, 250V/15A, with RCD, 10mA.
15/15EL10
Single Switched Socket Outlet, 250V/15A, with RCD, 30mA.
15/15EL30
Twin Switched Socket Outlet, 250V/10A, with RCD, 10mA.
25EL10
Twin Switched Socket Outlet, 250V/10A, with RCD, 30mA.
25EL30
Spacer Block, (L122 X W83 X H30mm).
25ELSB
Length
116mm
116mm
116mm
116mm
116mm
Width
74mm
74mm
74mm
74mm
74mm
25SF
115mm
73mm
-
-
115mm
73mm
11mm
84mm apart
46
46
258mm
184mm
184mm
73mm
85mm
85mm
17mm
18mm
18mm
230 x 40mm
152mm
152mm
46
46
46
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
11mm
11mm
11mm
11mm
11mm
11mm
11mm
11mm
11mm
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
47
47
47
47
47
47
47
47
47
33mm
33mm
18mm
18mm
18mm
11mm
11mm
17mm
17mm
17mm
11mm
11mm
17mm
17mm
17mm
N/A
N/A
N/A
N/A
N/A
48
48
48
48
48
54mm
29mm
25mm
N/A
48
22mm
22mm
21mm
22mm
22mm
22mm
22mm
22mm
22mm
21mm
22mm
22mm
22mm
22mm
26mm
19mm
19mm
38mm
35mm
33mm
28mm
N/A
N/A
N/A
N/A
N/A
N/A
N/A
49
49
49
49
49
49
49
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
49
49
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
115mm
122mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
73mm
78mm
11mm
11mm
11mm
11mm
11mm
11mm
11mm
14mm
14mm
14mm
14mm
16mm
16mm
16mm
32mm
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
84mm apart
51
51
51
51
51
51
51
51
51
51
51
51
51
51
51
116mm
73mm
14mm
84mm apart
51
Twin switched socket outlet, 250V/10A, surge protected. (L115 X W73 X H16mm).
Surge Filter Mechanism, 250V/10A.
30SFFM
COOKER SOCKET OUTLET & PLUG
1.8m, 4mm2 Cord, with 250V/32A 3 pin plug.
800CL
3 Pin Cooker Socket on Standard Plate, 250V/32A (Suits 800CL).
31VCS
UNIVERSAL SHAVER OUTLET - 240V-110V
Universal Shaver Outlet, Dual Voltage.
727
Universal Shaver Outlet, Dual Voltage (horizontal mount).
727H
Universal Shaver Outlet, Dual Voltage, (vertical mount).
727V
TV ANTENNA CONNECTION ACCESSORIES
1 Gang Standard Pattern Television Assembly.
31VTVA
TV Antenna Socket in Standard Plate, 75 Ohm.
31VTV75
“PAY TV” Antenna Socket in Standard Plate.
31TVF
“PAY TV/FTA TV” with a.c. Isolation.
32TVACFF
“PAY TV/FTA TV” with F Type Connection.
32TVFF
“PAY TV/FTA TV” Screw Coaxial Connection.
32TVSF
31VTV75ACF TV Socket with 3kVAc Isolation, 75 Ohm in standard size plate.
TV Socket with F Type Conneciton, 75 Ohm in standard size plate.
31VTV75F
32VTV75FM TV-FM Splitter in standard size plate.
TV CONNECTION SOCKETS, PLUGS & TERMINATORS
Coaxial Cable Plug, 75 Ohm.
30TV75P
TV Antenna Connection Socket, 75 Ohm.
30TV75CS
Coaxial RG59 Cable Connection Plug, 75 Ohm screw type.
30TV75C
Coaxial RG6 Cable Connection Plug, 75 Ohm screw type.
30TV75C1
Terminator, suits sockets.
30TV75T
TV SURFACE MOUNTING CONNECTION ACCESSORY
Coaxial Cable Surface Socket, 75 Ohm.
30TV75S
TV ANTENNA MECHANISMS
“F” Type Connection, 75 Ohm, suits “PAY TV”.
30PFM
“PAY TV/FTA TV” with F Type Connection.
30TVM
TV Socket, 300 Ohm type, front clip.
30TVFM
TV Antenna Socket, 75 Ohm, suits 30 Series plates.
30TV75M
TV Antenna Socket, 75 Ohm, with “F” type connection.
30TV75MF
30TV75MACF TV Antenna Socket, 75 Ohm, with 3kV a.c. isolation.
TV Antenna Socket, 75 Ohm (screw fixing, solderless).
30TV75MS
TV FLY LEADS - 1.8M
3105FL118MW Male to Male.
3105FL118FW Male to Female.
CHEMICAL RESISTANT STANDARD INDUSTRIAL RANGE
Flush Plate, with 1 x 30M mechanism in vertical format.
31VA
Flush Plate, with 2 x 30M mechanism in vertical format.
32VA
Flush Plate, with 3 x 30M mechanism in vertical format.
33VA
Flush Plate, with 4 x 30M mechanism in vertical format.
34VA
Flush Plate, with 5 x 30M mechanism in vertical format.
35VA
Flush Plate, with 6 x 30M mechanism in vertical format.
36VA
Blank Flush Plate.
31VX
Single Switched Socket Outlet, 250V/10A, horizontal mounting.
15
Single Switched Socket Outlet, 250V/10A, with extra switch, horizontal mounting.
15X
Single Switched Socket Outlet, 250V/15A, horizontal mounting.
15/15
Single Switched Socket Outlet, 250V/10A, vertical mounting.
15V
Twin Switched Socket Outlet, 250V/10A, single base, vertical mounting.
25V
Twin Switched Socket Outlet, 250V/10A, horizontal mounting.
25
Twin Switched Socket Outlet, 250V/10A, with extra switch, horizontal mounting.
25XA
1 Gang Mounting Block, suits all flush plates with 115 x 73mm and 84mm centres.
449A
14mm Spacer, for standard pattern accessories, with 84mm centres, four mounting
449ASD
holes in centre.
Depth
Mounting Centres PAGE
30mm
84mm apart
46
30mm
84mm apart
46
30mm
84mm apart
46
30mm
84mm apart
46
30mm
84mm apart
46
plate - 17mm
84mm apart
46
wall recess - 23mm
46
PROTECTED SWITCHED SOCKET OUTLETS - 250V/10A, ZINC DIE CAST
Cat No
Description
Length Width Depth Mounting Centres
3 flat sockets.
100mm 79mm
50mm
82mm apart
PC110
2 flat, 1 round socket.
100mm 79mm
50mm
82mm apart
PC110-2FR
1 flat socket.
100mm 79mm
50mm
82mm apart
PC110-2RF
3 flat sockets, with neon.
100mm 79mm
50mm
82mm apart
PC110-N
3 flat sockets, vertical mount, 2 gang.
142mm 102mm 50mm
84 x 82mm apart
PC110V-2
142mm 102mm 50mm
84 x 82mm apart
PC110V-2-DP zinc die cast, 3 flat sockets, vertical mount, 2 gang, double pole.
PROTECTED SWITCHED SOCKET OUTLETS - 250V/15A, ZINC DIE CAST
3 flat sockets.
101mm 79mm
50mm
82mm apart
PC115
3 flat sockets, with neons.
101mm 79mm
50mm
82mm apart
PC115-N
3 flat sockets, vertical mount, 2 gang.
141mm 102mm 50mm
84 X 82mm apart
PC115V-2
SWITCH MECHANISMS - 250V UNLESS STATED OTHERWISE
Cat No
Description
10A, 1 way/2 way - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30M
10A, 1 way/2 way (with red dolly mark)- terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole.M rating is 100.
30MRD
10A, 1 way/2 way (suits fluoro loads)- terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 120.
30FLM
15A, 1 way/2 way (suits fluoro loads)- terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 90.
30FLM15
15A, Rotary (2 On - 2 Off) - also suitable for 12V d.c. 15A, and audio and control applications. Switch positions indicated in window.M rating is 50.
30RSM2
15A, Rotary (3 On - 1 Off) - also suitable for 12V d.c. 15A, and audio and control applications. Switch positions indicated in window.M rating is 50.
30RSM3
10A, Changeover, double throw (selects alternate circuits).
30MCO
10A, Intermediate - four terminals of 3.5mm ø accommodates 2 x 2.5mm² cables. Body fits 22mm ø hole.
30MI
440V/15A, Bell press - offers facility for momentary ON or OFF (one Looping terminal).
30MBP
15A, Illuminated bell press - offers facility for momentary ON or OFF. Neon is connected across terminals 1 & 4.Alternative lamp voltages available.
30MBPN
10A, Bell press rocker - offers facility for momentary ON or OFF. Suitable for extra low voltage applications (one Looping terminal).
30MBPR
10A, 1 way, double pole, single throw - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole.M rating is 90.
30MD
10A, double pole, marked “HEAT”.
30HMD
10A, 2 Way, double pole, double throw - six terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. M rating is 75.
30MD2
15A, 1 way, double pole, single throw - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole.M rating is 90.
30MD15
20A, 1 way, double pole - 4 terminals of 1.5mm ø accommodate 3 x 2.5mm² cables. Body fits 34mm ø hole. M rating is 100.
30MD20
15A, 1 way/2 way - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 90.
30M15
15A, 1 way/2 way (with red dolly mark)- terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 90.
30M15RD
20A, 1 way/2 way - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 90.
30M20
35A, 1 way/2 way - terminal bore of 3.6mm ø & Looping terminal bore of 3.9mm ø. M rating is 160. Marked 35A.
30M35
20A (5A fluorescent load), 1 way/2 way, toggle key actuated - one Looping terminal. M rating is 100.
30TKM
10A, 1 way (two Looping terminals) - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30/1/2LM
10A, 1 way (one Looping & one Earth terminal) - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30/1ELM
10A, 1 way rocker with neon indicator - neon can be wired to indicate ON, OFF or POWER AVAILABLE. Looping/switch terminal bores of 4.1mm ø. Body fits 34mm ø hole
30/1NM
(Note: Neutral required).
10A, 2 way rocker with neon indicator - neon can be wired to indicate ON, OFF or POWER AVAILABLE. Looping/switch terminal bores of 4.1mm ø. Body fits 34mm ø hole
30/2NM
(Note: Neutral not required).
10A, 1 way/2 way (with 5 terminals - one Looping and one Earth terminal). Terminal bore of Common, Looping and Earth of 5.3mm ø accommodates 4 x 2.5mm²
30/5M
cables. Terminal bore of ‘1’ and ‘2’ of 4.1mm ø accommodates 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 26mm ø hole. M rating is 40.
NEON INDICATOR MECHANISMS - 250V
Neon indicator (RED)
30N - RED
30N Neon indicator (OTHER COLOURS)
OTHER COLOURS
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
PAGE
54
54
54
54
54
54
54
54
54
PAGE
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
56
57
57
SWITCH MECHANISMS - 250V/10A, TERMINAL BORES OF 4.1mm o ACCOMODATE 4 X 1.5mm2 CABLES,
BODY FITS 22mm o HOLE 2 WAY WITH MESSAGES
30FM
30HM
30EM
30LM
30MAM
30PM
30XM
30YM
30DNM
30FAM
30TM
30COM
30AUM
30ACM
30STM
Marked “FAN” - M rating is 100.
Marked “HEAT” - M rating is 100.
Marked “EXHAUST” - M rating is 100.
Marked “LIGHT” - M rating is 100.
Marked “MANUAL-AUTO” - M rating is 100.
Marked“DISPOSAL” - M rating is 100.
Marked “WASTE” - M rating is 100.
Marked “WASH” - M rating is 100.
Marked “DAY/NIGHT” - M rating is 100.
Marked “FAMILY” - M rating is 100.
Marked “T.V.” - M rating is 100.
Marked “COOL” - M rating is 100.
Marked “AUTO” - M rating is 100.
Marked “AIR CON” - M rating is 100.
Marked “STUDY” - M rating is 100.
57
57
57
57
57
57
57
57
57
57
57
57
57
57
57
79
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
STANDARD RANGE QUICK REFERENCE GUIDE (Continued)
SWITCH MECHANISMS - 250V/10A, 2 WAY WITH MESSAGES250V/10A, TERMINAL BORES OF 4.1mm o
ACCOMODATE 4 X 1.5mm2 OR 3 X 2.5mm2 CABLES, BODY FITS 22mm o HOLE 2 WAY WITH MESSAGES
Cat No
Description
Marked“PUMP” - M rating is 100.
30PUM
Marked “BATH” - M rating is 100.
30BM
Marked “KITCHEN” - M rating is 100.
30KM
Marked “RUMPUS” - M rating is 100.
30RUM
Marked “LOUNGE” - M rating is 100.
30LOM
Marked “DINE” - M rating is 100.
30DM
Marked “OFF/ON” - M rating is 100.
30FNM
Marked “ALARM” - M rating is 100.
30AM
Marked “BED” - M rating is 100.
30BDM
Marked “BED1” - M rating is 100.
30BD1M
Marked “BED2” - M rating is 100.
30BD2M
Marked “BED3” - M rating is 100.
30BD3M
Marked “BED4” - M rating is 100.
30BD4M
Marked “HI/LOW” - M rating is 100.
30HLM
Marked “SENSOR” - M rating is 100.
30MSEN
Marked “OUTSIDE” - M rating is 100.
30MOS
Marked “FORWARD/REVERSE” - M rating is 100.
30MFR
Marked “FRIDGE” - M rating is 100.
30MFD
Marked “MICROWAVE” - M rating is 100.
30MMW
marked “ZONE1” - M rating is 100.
30MZ1
Marked “ZONE2”- M rating is 100.
30MZ2
Marked “ZONE3” - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MZ3
Marked “ZONE4” - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30MZ4
3 Position - marked “HI-OFF-LO”. Three terminals, 3.5mm ø accommodate 2 x 2.5mm² cables.
39M
3 Position - marked “MAN-OFF-AUTO”. Three terminals, 3.5mm ø accommodate 2 x 2.5mm² cables.
39MAOM
3 Position - marked “SENSOR-OFF-ON”. Three terminals, 3.5mm ø accommodate 2 x 2.5mm² cables.
39MSON
SWITCH MECHANISMS - 250V/16A, TERMINAL BORES OF 4.1mm o ACCOMODATE 4 X 1.5mm2 OR 3 X 2.5mm2 CABLES,
BODY FITS 22mm o HOLE 2 WAY WITH MESSAGES
Marked “SENSOR” - M rating is 100.
30M16SEN
Marked “OUTSIDE” - M rating is 100.
30M16OS
Marked “FORWARD/REVERSE” - M rating is 100.
30M16FR
Marked “FRIDGE” - M rating is 100.
30M16FD
Marked “MICROWAVE” - M rating is 100.
30M16MW
SWITCH MECHANISM - 250V/20A, 2 WAY WITH MESSAGE
Marked “HOT WATER SERVICE” - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30M20HW
SWITCH MECHANISMS - 250V/35A, TERMINAL BORES OF 4.1mm o ACCOMODATE 4 X 1.5mm2 OR 3 X 2.5mm2 CABLES,
BODY FITS 22mm o HOLE 2 WAY WITH MESSAGES
Marked “HOB” - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30M35HOB
Marked “OVEN” - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30M350V
Marked “RANGE” - terminal bores of 4.1mm ø accommodate 4 x 1.5mm² or 3 x 2.5mm² cables. Body fits 22mm ø hole. M rating is 100.
30M35R
10A ILLUMINATED ROCKER SWITCH MECHANISMS, 250V/10A, 2 WAY INBUILT NEON, WITH MESSAGES
80
PAGE
58
58
58
58
58
58
58
58
58
58
58
58
58
58
58
58
58
58
58
58
59
59
59
59
59
59
59
59
59
59
59
59
59
59
59
30/2NMSEN
Marked “SENSOR”. Neon can be wired to indicate ON, OFF or POWER AVAILABLE. Looping/switch terminals of bore 3.9mm ø. Body fits 34mm ø hole.
60
30/2NMOS
Marked “OUTSIDE”. Neon can be wired to indicate ON, OFF or POWER AVAILABLE. Looping/switch terminals of bore 3.9mm ø. Body fits 34mm ø hole.
60
DIMMER, FAN CONTROL AND SURGE FILTER MECHANISMS
32E450LM
C-Thru® Dimmer Mechanism, Leading Edge (suits incandescent lighting and low voltage lighting using iron core transformers), 220 - 240V/450W.
32E450TM
C-Thru® Dimmer Mechanism, Trailing Edge (suits incandescent lighting and low voltage lighting using electronic transformers), 220 - 240V/450W.
32E500FM
C-Thru® Fan Speed Controller Mechanism, 220-240V/500W.
30POTDM
Dimmer Potentiometer (suits products such as 780 Series and the 761 Series).
30POTFM
Fan Controller Potentiometer (suits products such as 32 Series High Powered Dimmers & 761 Series).
30SFM
Surge Filter Mechanism - 250V 10A.
CIRCUIT IDENTIFICATION AND BLANKING PRODUCTS
Removable Blank Plug, to suit or blank out 30 Series aperture.
30P
Removable Plug, with identification facility, supplied with tamper proof transparent cover.
30PID
Plug, marked “FRIDGE - FREEZER ONLY”.
30PFO
Label Sheets, 10 x A4 packet, red and white available (non-adhesive).
30PIDA4L
60
60
60
60
60
60
60
60
60
60
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
449ASD
YES
N8
YES
YES
Y1
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
YES
449A
YES
N8
YES
YES
YES
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
NS12
NS12
448
NS12
NS12
NS12
NS12
NS12
YES
NS3
NS3
NS12 NS13
NS14
NS15 NS16
NS11
NS12
NS12
448SD
NS12
NS12
NS12
NS12
NS12
YES
NS3
NS3
NS12 NS13
NS14
NS15 NS16
NS10
NS11
YES
YES
238
YES
N8
YES
YES
YES
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
NS
NS10
NS11
YES
YES
900SPBP
YES
N8
YES
YES
YES
NS
NS3
NS3
NS13
NS14
NS15 NS16
NS
NS
NS10
NS11
YES
YES
900SPMB
YES
N8
YES
YES
YES
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
YES
NS
NS
NS10
NS11
YES
YES
25ELSB
YES
N8
YES
YES
YES
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
NS12
NS
NS
NS10
NS11
NS12
NS12
900MMB
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
70/1
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
70/2
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
NS8
NS8
NS9
Y1
NS
NS
NS10
NS11
YES
Y1
449AS
449ASD
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
449A
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
448
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS
YES
YES
NS10
NS11
448SD
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS
YES
YES
NS10
238
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
900SPBP NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
900SPMB NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
900MMB YES NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
N8
70/1
YES NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
NS
NS
NS10
NS11
NS12
NS12
70/2
NS1 YES
NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
NS
NS
NS10
NS11
NS12
NS12
70/3
NS1 NS2
YES
NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
NS
NS
NS10
NS11
NS12
NS12
70/3
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
70B
NS1 NS2 NS3 NS4
NS5
NS6
NS7
YES
NS8
NS8
NS9
NS12
NS
NS
NS10
NS11
NS12
NS12
70B
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
47
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
N10
YES
NS9
NS12
NS
NS
NS10
NS11
NS12
NS12
47
NS12
NS12
NS12
NS12
NS12
NS
NS3
YES
NS12 NS13
NS14
NS15 NS16
536
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
NS
NS
NS10
YES
NS12
NS12
536
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
NS12 NS13
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
1920MB
YES
YES
YES
YES
YES
NS
NS3
NS3
154
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
Y1
NS
NS
NS10
NS11
YES
Y1
154
Y1
YES
Y1
Y1
Y3
NS
NS3
NS3
154RM
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
Y1
NS
NS
NS10
NS11
YES
Y1
154/2
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
YES
YES
NS10
NS11
NS12
NS12
155PRM
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
Y1
NS
NS
NS10
NS11
YES
Y1
155P
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
Y1
NS
NS
NS10
NS11
YES
Y1
155
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
Y1
NS
NS
NS10
NS11
YES
Y1
155NA
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
Y1
NS
NS
NS10
NS11
YES
Y1
157/1P
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
157/1PRM NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
WALL
CLIPS
1920MB
NS14
NS15 NS16
Y1
NS13
NS14
NS15 NS16
Y1
NS13
NS14
NS15 NS16
NS12 NS13
NS14
NS15 NS16
Y1
YES
Y1
Y1
Y3
NS
NS3
NS3
154/2
NS12
NS12
NS12
NS12
NS12
YES
NS3
NS3
155PRM
Y1
YES
Y1
Y1
Y3
NS
NS3
NS3
Y1
NS13
NS14
NS15 NS16
155P
Y1
YES
Y1
Y1
Y3
NS
NS3
NS3
Y1
NS13
NS14
NS15 NS16
155
Y1
YES
Y1
Y1
Y3
NS
NS3
NS3
Y1
NS13
NS14
NS15 NS16
155NA
Y1
YES
Y1
Y1
Y3
NS
NS3
NS3
Y1
NS13
NS14
NS15 NS16
YES
157/1P
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
YES
YES
157/1PRM
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
WALL BRACKETS
AND PLATES
154RM
257
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
257
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
257D
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
257D
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
257D2
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
YES
YES
NS10
NS11
NS12
NS12
257D2
NS12
NS12
NS12
NS12
NS12
YES
NS3
NS3
NS12 NS13
NS14
NS15 NS16
257D3
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
NS
NS
YES
NS11
NS12
NS12
257D3
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
157
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
157
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
157/1
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
157/1X
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
157/1
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
157/1X
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
157/2
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
YES
YES
NS10
NS11
NS12
NS12
157/2
NS12
NS12
NS12
NS12
NS12
YES
NS3
NS3
NS12 NS13
NS14
NS15 NS16
160
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
160
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
164
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
164/1
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
YES
NS
NS
NS10
NS11
YES
YES
164
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
YES
164/1
YES
YES
YES
YES
YES
NS
NS3
NS3
YES
NS13
NS14
NS15 NS16
164/2
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
YES
YES
NS10
NS11
NS12
NS12
164/2
NS12
NS12
NS12
NS12
NS12
YES
NS3
NS3
NS12 NS13
NS14
NS15 NS16
727VHB
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
NS
NS
NS10
NS11
NS12
NS12
727VHB
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
727B
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
NS
NS
NS10
NS11
NS12
NS12
727B
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
727MB
NS1 NS2 NS3 NS4
NS5
NS6
NS7
NS1
NS8
NS8
NS9
NS12
NS
NS
NS10
NS11
NS12
NS12
727MB
NS12
NS12
NS12
NS12
NS12
NS
NS3
NS3
NS12 NS13
NS14
NS15 NS16
81
YOU WILL FIND THE KEY TO THIS TABLE ON PAGE 86
MOUNTING BLOCKS
NS1
WALL
CLIPS
NS7
WALL BRACKETS
AND PLATES
NS6
16X
31E800T,
31E1000L,
31VETF
31VETR,
31VETR3,
31VSSR
319,
319RA,
319N,
319HP
319X
TC15/24,
TC15/15/24,
TC15/15/7D
TC32V1,
TC32V24,
TC32V7D
15/15EL10,
15/15EL30,
25EL10,
25EL30
15XRZ,
15X15RZ
25SF
727
727V
727H
449AS
Y3
Y4
N12
Y3
Y4
NS6
Y3
Y6
Y4
Y2
NS17
NS18
449ASD
Y2
Y3
N12
Y2
Y3
NS6
Y2
Y6
Y3
Y2
NS17
NS18
YES
449A
YES
N3
N3
YES
YES
NS6
YES
YES
N3
NS17
NS18
448
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
448SD
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
238
YES
YES
YES
YES
NS12
NS6
YES
YES
YES
YES
NS17
NS18
900SPBP
Y1
Y2
Y2
Y1
Y2
NS6
Y1
Y4
Y2
YES
NS17
NS18
900SPMB
YES
YES
YES
YES
NS12
NS6
YES
YES
YES
YES
NS17
NS18
25ELSB
YES
YES
YES
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
900MMB
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
70/1
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
70/2
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
70/3
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
70B
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
47
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
536
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
1920MB
YES
Y2
N13
Y1
Y1
NS6
YES
YES
Y1
YES
NS18
154
Y4
Y4
Y4
Y3
Y4
NS6
YES
Y6
YES
Y3
NS17
NS18
Y4
Y4
Y4
Y3
Y4
NS6
YES
Y6
YES
Y3
NS17
NS18
154/2
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
155PRM
Y4
Y4
Y4
Y3
Y4
NS6
YES
Y6
YES
Y3
NS17
NS18
155P
Y4
Y4
Y4
Y3
Y4
NS6
YES
Y6
YES
Y3
NS17
NS18
155
Y4
Y4
Y4
Y3
Y4
NS6
YES
Y6
YES
Y3
NS17
NS18
155NA
Y4
Y4
Y4
Y3
Y4
NS6
YES
Y6
YES
Y3
NS17
NS18
157/1P
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
157/1PRM
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
257
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
Cat
No.
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
257D3
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
157
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
157/1
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
157/1X
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
157/2
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
160
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
164
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
164/1
YES
YES
X5
YES
YES
NS6
YES
YES
YES
YES
NS17
NS18
164/2
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
NS18
727VHB
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12 NS17
YES
727B
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12
YES
NS18
727MB
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12
YES
NS18
31VA,
31HA,
32VA,
32HA,
33VA,
33HA,
34VA,
34HA,
35VA,
34/2VA,
36VA,
35/2VA,
31VHWP,
30,
36VKT3N, 31/2VA 36/2VA,
35BMF,
30D,
16/2MF, 36VKT3NX 32/2VA 37/2VA,
30/15,
36VKT4, 33/2VA 38/2VA,
39,
31BA 31BLA 31BMF 16/2MFD,
30DD 32A 33A 34A 30T 32TA 33TA 32BA 32BLA 32BMF 16/2MF1510 36VKT4X 31/2VX 39/2VA 31/3VX 31VR 31VTO 31VCS
157/1F NS1 NS2 NS3 NS4 NS5 NS6 NS7 NS1
NS8
NS8
NS9
YES
NS
NS
NS10 NS11 YES
YES
F157/1 NS1 NS2 NS3 NS4 NS5 NS6 NS7 NS1
NS8
NS8
NS9
YES
NS
NS
NS10 NS11 YES
YES
157/2F NS1 NS2 NS3 NS4 NS5 NS6 NS7 NS1
NS8
NS8
NS9
NS12
YES
YES
NS10 NS11 NS12 NS12
224/1
NS1 NS2 NS3 NS4 NS5 NS6 NS7 NS1
NS8
NS8
NS9
YES
NS
NS
NS10 NS11 YES
AS
223H
NS1 NS2 NS3 NS4 NS5 NS6 NS7 NS1
NS8
NS8
NS9
Y1
NS
NS
NS10 NS11 YES
AS
255
NS1 NS2 NS3 NS4 NS5 NS6 NS7 YES
YES
NS8
NS9
YES
NS
NS
NS10 NS11 YES
AS
240
Series NS1 NS2 NS3 NS4 NS5 NS6 NS7 NS1
T240
Series NS1 NS2 NS3 NS4 NS5 NS6 NS7 NS1
SC240 NS1 NS2 NS3 NS4 NS5 NS6 NS7 NS1
Series
NS8
NS8
NS9
NS12
NS
NS
NS10 YES NS12 NS12
NS8
NS8
NS9
NS12
NS
NS
NS10 YES NS12 NS12
NS8
NS8
NS9
NS12
NS
NS
NS10 YES NS12 NS12
Cat
No.
NS18
257D2
82
YOU WILL FIND THE KEY TO THIS TABLE ON PAGE 86
NS17
154RM
257D
WALL BOXES
NS5
MOUNTING BLOCKS
NS1 NS2 NS3 NS4
14
Cat
No.
23,
23X
32E450L,
32E450T,
32E500F
32E450L, 31E800T,
32E450T, 31E1000L,
31VETF
32E500F
31VETR,
31VETR3,
31VSSR
319,
319RA,
319N,
19HP
319X
TC15/24,
TC15/15/24,
TC15/15/7D
TC32V1,
TC32V24,
TC32V7D
15/15EL10,
15/15EL30,
25EL10,
25EL30
15XRZ,
15X15RZ
25SF
727
727V,
727H
157/1F
YES
YES
X5
YES
YES
NS6
YES
YES
X5
YES
NS17 NS18
F157/1
X5
YES
X5
YES
YES
NS6
YES
YES
X5
YES
NS17 NS18
157/2F
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12
NS17 NS18
224/1
YES
YES
YES
YES
YES
NS6
YES
N6
YES
T
NS17 NS18
223H
Y4
Y4
Y4
Y3
Y4
NS6
Y4
N3
N3
Y3
NS17 NS18
255
YES
YES
YES
YES
YES
NS6
Y7
Y7
Y
YES
NS17 NS18
240
Series
T240
Series
SC240
Series
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12
NS17 NS18
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12
NS17 NS18
NS12
NS12
NS12
NS12
NS12
NS6
NS12
NS12
NS12
NS12
NS17 NS18
83
YOU WILL FIND THE KEY TO THIS TABLE ON PAGE 86
MOUNTING ACCESSORIES CROSS REFERENCE CHART
Y2
449AS
40
16/2,
16/2S,
16/2N,
16/2F
FIRE RATED
WALL BOXES
Y1
31VCS
16,
16N ,
16F,
16/15
ENCLOSURES
Y1
31VTO
33TA
15/2,
15/2S,
15/2N,
25/2V,
25/2VS,
25/2VN 15DD2V
JUNCTION
BOXES
N8
31VR
32TA
15/2V,
15/2VS,
15/2VN,
15D2V,
JUNCTION ENCLOSURES FIRE RATED
BOXES
WALL BOXES
Y1
31/3VX
Cat
No.
WALL BOXES
MOUNTING BLOCKS
WALL
CLIPS
WALL BRACKETS
AND PLATES
15DX
34/2VA
35/2VA
36/2VA
37/2VA
38/2VA
39/2VA
30T
25ELSB
15DN,
15/15,
15/15S,
15/15N,
15L,
15LN,
15XX,
25, 25L, 25X,
25XS, 25XA,
25XAN, 25XD 25S,
25N, 25D, 25D15,
25/15, 25/15S,
25/15N, 25/1510,
42/20, 42/20N
15DD
31/2VA
32/2VA
33/2VA
31/2VX
34A
33A
31BMF
32BMF
10,
10D,
10DS,
10DN,
10DLS,
10D15S,
20,
20D,
20DS,
20DN,
20DLS,
15, 15X
15S, 15N,
15D, 15D15,
15V,
15VS,
15VX,
15VXN,
15VXX,
15V15,
25V,
25VXA
31BA 31BLA
32BA 32BLA
Cat
No.
WALL BOXES
30,
30D
30/15
39
30DD 32A
31VA
31HA
32VA
32HA
33VA
33HA
34VA
34HA
35VA, 36VA
31VHWP
36VKT3N
35BMF
36VKT3NX
16/2MF
36VKT4
16/2MFD
16/2MF1510 36VKT4X
84
YOU WILL FIND THE KEY TO THIS TABLE ON PAGE 86
YES
YES
YES
YES
NS
NS3
NS3 YES NS13 NS14 NS15 NS16
F157/1
YES
YES
YES
YES
YES
NS
NS3
NS3 YES NS13 NS14 NS15 NS16
157/2F
NS12
NS12
NS12
NS12
NS12
YES
NS3
NS3 NS12 NS13 NS14 NS15 NS16
ENCLOSURES
224/1
YES
NS12
YES
AS
AS
NS
NS3
223H
Y1
NS12
NS
AS
AS
NS
255
YES
NS12
YES
AS
AS
240
Series
T240
Series
SC240
Series
NS12
NS12
NS12
NS12
NS12
NS12
NS12
NS12
NS12
NS12
AS
The product can be mounted, however, it will not meet Australian Standards requirements.
N3
Product base fouls the accessory mounting bosses, meaning that the product can’t be mounted flush.
N6
The product can be mounted, however, the ‘press to test’ & ‘press to reset’ buttons can’t be pushed.
N8
The finished result looks very unprofessional.
N10
Mounting centres line up, however, the product overhangs the accessory.
N12
The bosses attaching the mechanism back box to the flush plate protrude below the flush plate edge, meaning that the product can’t be mounted flush.
N13
Product base is too large to fit into the accessory.
NS1
Can be direct mounted to surface (55mm mounting centres).
NS2
Can be direct mounted to surface (70mm mounting centres).
NS3
Can be direct mounted to surface (98mm mounting centres).
NS4
Can be direct mounted to surface (124mm mounting centres).
NS5
Can be direct mounted to surface (40mm mounting centres).
NS6
Can be direct mounted to surface (60mm mounting centres).
NS7
Individual Switch & Socket sections for the Standard Range have been formatted to indicate if a product
can or cannot be installed with a particular mounting accessory.
This cross reference charts is best used in conjunction with the “Key” on Page 86.
Product of Clipsal Australia Pty Ltd
ABN 27 007 873 529
Head Office
12 Park Terrace, Bowden
South Australia 5007
Telephone (08) 8269 0511
Facsimile (08) 8340 1724
Internet clipsal.com
E-Mail plugin@clipsal.com.au
Offices in all States
NSW Sydney
Albury
(02) 9794 9200
(02) 6041 2377
VIC
Melbourne
Country Areas
(03) 9207 3200
1800 653 893
QLD
Brisbane
Townsville
(07) 3244 7444
(07) 4729 3333
SA
Adelaide
(08) 8268 0400
WA
Perth
(08) 9442 4444
Can be direct mounted to surface (87mm mounting centres).
TAS
Launceston
(03) 6343 5900
NS8
Can be direct mounted to surface (78mm mounting centres).
NT
Darwin
(08) 8947 0278
NS3 NS12 NS13 NS14 NS15 NS16
NS9
Can be direct mounted to surface (136mm mounting centres).
NS3
NS3 NS12 NS13 NS14 NS15 NS16
NS10
Can be direct mounted to surface (84mm mounting centres - 3 sets, 46mm apart).
NS
NS3
NS3 NS12 NS13 NS14 NS15 NS16
NS11
Can be direct mounted to surface (50mm mounting centres).
NS12
NS
NS3
NS3 NS12 NS13 NS14 NS15 NS16
Area Representatives
NSW Albury
Mid North Coast
Coffs Harbour
Dubbo
Newcastle
NS12
Can be direct mounted to surface (84mm mounting centres).
NS12
NS12
NS
NS3
NS3 NS12 NS13 NS14 NS15 NS16
NS13
Can be direct mounted to surface (75mm mounting centres).
NS12
NS12
NS
NS3
NS3 NS12 NS13 NS14 NS15 NS16
NS14
Can be direct mounted to surface (145mm mounting centres).
NS15
Can be direct mounted to surface (104mm mounting centres).
15V,
15VS, 15VX,
15VXN, 15VXX, 15/2V,
15/2, 15/2S,
15/2VS,
15V15,
15/2VN, 15/2N, 25/2V,
25V,
15D2V, 25/2VS, 25/2VN 15DD2V
25VXA
40
14
16/2,
16,
16N, 16/2S,
16F, 16/2N,
16/15 16/2F
16X
23,
23X
NS16
Can be direct mounted to surface (120mm mounting centres).
NS17
Can be direct mounted to surface (230mm x 40mm mounting centres).
NS18
Can be direct mounted to surface (153mm mounting centres).
T
CODE
YOU WILL FIND THE KEY TO THIS TABLE ON PAGE 86
ACT
Canberra
0419 238 824
0418 164 070
VIC
Bendigo
Geelong
Gippsland
Western Victoria
0418 570 213
0418 527 233
0418 512 680
0419 380 444
Cairns
Mackay
Maryborough
Northern Rivers
Rockhampton
Sunshine Coast
Toowoomba
Townsville
0418 773 254
0418 752 134
0418 664 338
0418 768 902
0419 869 752
0418 711 786
0418 726 394
0418 180 372
The text on the top of the cover can’t be seen.
QLD
DESCRIPTION - SUITABLE
X5
Ensure mounting accessory is set back 25mm from outer wall surface.
Y1
Allow 10mm depth for mechanism and cable protrusion.
Y2
Allow 15mm depth for mechanism and cable protrusion.
Y3
Allow 20mm depth for mechanism and cable protrusion.
Y4
Allow 25mm depth for mechanism and cable protrusion.
Y6
Allow 45mm depth for mechanism and cable protrusion.
Y7
The conduit plugs or conduit have to be shortened to accommodate the large base of product.
86
WA
SA
Bunbury
0418 931 684
Kalgoorlie &
0417 928 981
Eastern Gold Fields
Karratha
0418 937 249
Riverland/Mildura/
Broken Hill
0418 596 145
International Enquiries
International Sales and Marketing
Telephone + 61 8 8269 0587
Facsimile + 61 8 8340 7350
E-Mail export@clipsal.com.au
New Zealand
Clipsal Industries (NZ) Ltd
Telephone (09) 576 3403
Facsimile (09) 576 1015
E-Mail headoffice@clipsal.co.nz
Customer Service
Free Fax (0508) 250 305
Auckland/Mobile Phone (09) 572 0014
Free Phone (0508) CLIPSAL
2547725
You can find this brochure and many
others online in PDF format at:
clipsal.com
Follow the links off the home page
or access the following page directly:
clipsal.com/wat_lib_pdf.cfm
clipsal.com
Special thanks to
Graham Ward (Active Connection Electrical)
and Greg Spurling (Spurling Electrical)
for their contribution to this catalogue.
The shape of the switch dolly is a trade mark of
Clipsal Australia Pty. Ltd.
Clipsal Australia Pty Ltd reserves the right to change
specifications, modify designs and discontinue items
without incurring obligation and whilst every effort is
made to ensure that descriptions, specifications and
other information in this catalogue are correct, no
warranty is given in respect thereof and the company
shall not be liable for any error therein.
© Copyright Clipsal Australia Pty Ltd 2005.
All rights reserved.
This material is copyright under Australian and
international laws. Except as permitted under the
relevant law, no part of this work may be reproduced
by any process without prior written permission of
and acknowledgement to Clipsal Australia Pty Ltd.
O/N 8414 July 05/01
85
(02) 6041 2377
0418 430 361
0418 653 183
0418 822 564
0407 298 792
0418 434 169
0418 686 040
South West Sydney 0419 868 353
Tamworth
0417 714 339
Wagga Wagga
0418 578 903
Wollongong
0418 423 581
technical
te
chn
data
YES
It is often difficult to determine which mounting accessory is best utilised when installing the vast amount
of products in the Clipsal switch & socket ranges. The cross-reference chart in the following pages will
help you to simplify this task.
DESCRIPTION - NOT SUITABLE
O/N 8414 July 05/01
157/1F
MOUNTING ACCESSORIES CROSS REFERENCE CHART
C1-002
15DX
FIRE RATED
WALL BOXES
15DD
JUNCTION
BOXES
MOUNTING ACCESSORIES CROSS REFERENCE CHART
Cat
No.
CODE
STANDARD SERIES - No other range is up to standard
MOUNTING ACCESSORIES CROSS REFERENCE CHART
10,
10D,
10DS,
10DN,
10DLS,
10D15S,
20,
20D,
20DS,
20DN,
15,
15S,
15N,
15D,
15D15,
15DN,
15/15,
15/15S,
15/15N,
15L,
15LN,
15X,
15XX,
25,
25L,
25X,
25XS,
25XA,
25XAN,
25XD,
25S,
25N,
25D,
25D15,
25/15,
25/15S,
25/15N,
25/1510,
42/20,
42/20N
clipsal.com
Download PDF