www.jbctools.com English 2 Tools Control Unit Ref. DD-B 2 w w w.jbctools.com Packing List The following items should be included: DD Control Unit ...................................... 1 unit Power Cord ............................................... 1 unit DD Control Unit Ref. DD-1B (120V) DD-2B (230V) DD-9B (100V) Power Cord Ref. 0009417 (100V/120V) 0009401 (230V) Manual w w w.jbctools.com 2 Tools Control Unit Ref. DD-B 3 Features For a basic working system, you need 1 control unit, 1 stand, 1 tool and 1 cartridge. DD Control Unit Ref. DD-1B (120V) DD-2B (230V) DD-9B (100V) Compatible modules Ref. MS, MV, MN, FS Power Cord Socket Compatible stands Ref. AD-SD, PA-SD, AP-SD, HT-SD, DS-SD, DR-SD, DN-SD Compatible tools Ref. T210, T245, T245-NA, PA120, AP130, HT420, DS360, DR560 4 w w w.jbctools.com USB Connector Download the latest softwares from our website to improve your soldering station. JBC Updater www.jbctools.com/software.html Update the station software via USB connection: Cable USB AB JBC Manager www.jbctools.com/manager.html Manage and monitor as many stations as your Windows PC supports by using the JBC Manager. You can export data to another PCs. any JBC station Cable USB AB USB Hub JBC Manager Manager Settings Change settings for a group of JBC stations at the same time. Register Settings Create graphs of the soldering process in real time with power and temperature data. 5 Operation The JBC Exclusive Heating System This revolutionary technology is able to recover the tip temperature extremely quickly. This allows the user to work at a lower temperature. As a result, the tip life increases x5 times. 1. Work 2. Sleep 3. Hibernation After 30’ Lift tool from the stand and the tool tip will heat up to the selected temperature. Selected temp. 3 5 0 o C 350 c 0 Power 10% · Change temperature (from 90 to 450ºC) · Set temperature limits · Select temperature levels · Fix one temperature 6 When the tool is in the stand, the temperature reduces to 180ºC / 360ºF (preset sleep temperature). Sleep After longer periods of inactivity (pre-set to 30 minutes), the power is cut off and the tool cools down to room temperature. Hibernation Tool in the stand Tool in the stand after sleep No heat A c t u a l T e m p . 1 8 0 oC A c t u a l T e m p . 2 0 oC · Change Sleep temperature · Set Sleep delay (from 0 to 9 min or no Sleep) · Set Hibernation delay (from 0 to 60 min or no hibernation) w w w.jbctools.com Process Control Work Screen Displays a specific fixed temp. Fixed temp. 3 5 0 o C Shown when you have selected temp. levels. Levels ºC 2 7 0 3 5 0 4 0 0 Selected temp. 3 5 0 o C 350 0c The work screen provides useful information of tool status in real time. Tip temparature Power 10% Decrease & move down % Instant power supplied to the tool Increase & move up Access Menu & Confirm Selection Menu Screen Main menu Original PIN: 0105 Station settings 1 2 3 4 Temp unit Maximum temp Minimum temp Nitrogen mode 5 Help text 6 Beep 7 Change PIN Back 1 2 3 Exit Reset settings Station settings Tool settings 4 5 Counters Program version Counters Tool settings Celsius 4000C 2000C OFF 1 Fix one temp ----2 Temp levels set OFF 3 Sleep delay 0 min 1 Plugged hours 2 Working hours 3 Sleep hours Port 1 Port 1/2 OFF ON 4 Sleep temp 1800C 5 Hibernation delay 30 min 6 Temp adjust + O OC Port 1 Tool DR Back Tool DR 4 5 6 7 Hibernation hours No tool hours Sleep cycles Desoldering cycles Port 1/2 0 0 0 0 0 0 0 Back 7 Maintenance Before carrying out maintenance or storage, always allow the equipment to cool. - Clean the station’s screen with a glass cleaner or a damp cloth. - Use a damp cloth to clean the casing and the tool. Alcohol can only be used to clean the metal parts. - Check periodically that the metal parts of the tool/stand are clean so that the station can detect when the tool is in the stand. - Maintain tip surface clean and tinned prior to storage in order to avoid tip oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint. - Periodically check all cable connections. - Replace the fuse if it is blown according to the following guidelines: Fuse Remove the fuse by pulling the black cap. If necessary use a tool to lever it off. Press the new fuse into the holder and replace it in the station. - Replace any defective or damaged pieces. Use original JBC spare parts only. - Repairs should only be performed by a JBC authorized technical service. 8 w w w.jbctools.com Safety It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion. - Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire. - The power cord must be plugged into approved bases. Be sure that it is properly grounded before use. When removing it, hold the plug, not the wire. - Do not work on electrically live parts. Antistatic handle of soldering irons is electrically conductive. - The tools should be placed in the stand when not in use in order to activate the sleep mode. The soldering tip, the metal part of the tool and the stand may still be hot even when the station is turned off. Handle with care, including when adjusting the stand position. - Do not leave the appliance unattended when it is on. - Do not cover the ventilation grills. - Heat can cause inflamable products to ignite even when out of sight. - Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation. - Be careful with the fumes produced when soldering. - Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal harm. - Utmost care must be taken with liquid tin waste which can cause burns. - This appliance can be used by children over the age of eight and also persons with reduced physical, sensory or mental capabilities or lack of experience provided that they have been given adequate supervision or instruction concerning use of the appliance and understand the hazards involved. Children must not play with the appliance. Maintenance shall not be carried out by children unless supervised. 9 Exploded View 10 w w w.jbctools.com Specifications DD-1B 120V 50/60Hz. Input fuse: 4A. Output: 23.5V. DD-2B 230V 50/60Hz. Input fuse: 2A. Output: 23.5V. DD-9B 100V 50/60Hz. Input fuse: 4A. Output: 23.5V. - Total unit weight: 3,6 kg (7.8 lb) - Size: 145 x 120 x 225 mm - Temperature selection from 90°C (190°F) to 450°C (840°F) - Output Peak Power: 150W - Tip to ground resistance: <2 ohms - Ambient operating temp: 10-40 ºC / 50-104 ºF - USB connector station-PC - Complies with CE standards - ESD protected housing “skin effect” 11 This product should not be thrown in the garbage. In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life must be collected and returned to an authorized recycling facility. www.jbctools.com 0008386-0714 Warranty JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear due to use or mis-use. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project