LIRDBSM Colour Camera Specification Specification

Specification
Model
LIRDBSM
Pick up Element
1/3"CMOS
Effective Picture Elements
(H×V)
976(H) X 496(V)
Horizontal Resolution
800TV Line
Minimum lllumination
0.01Lux/F1.2
S/N Ratio
More than 48dB
Scanning System
2:1 interlace
Synchronous System
Internal, Negative sync.
Auto Electronic Shutter
NTSC:1/60s~1/100,000s,PAL:1/50s~1/100,000s
Gama Characteristic
0.45
IR Distance
20 Meters (with ¢5X24 Unit Infrared LED)
IR Status
Under 10 Lux by CDS
IR Power On
CDS AUTO Control
Video Output
1Vpp,75 Ω
Auto Gain Control
Auto
Power/Current
DC12V(+/-10%)/ 350mA
Lens
Board Lens 3.6mm/F2.0
Dimension (mm)
¢94 x 69(H)
Weight (g)
400
LIRDBSM Colour Camera
Vandalproof IR Dome Colour Camera
Storage Temperature
-30~ +60℃
RH95% MAX
Operating Temperature
-10~ +50℃
RH95% MAX
Notes:Before providing power for the
camera, please read this User Guide in
detail!
Franchiser:
Packing List
No
Name
Model
Number
1.
Vandalproof IR Dome Colour Camera
LIRDBSM
1
2.
User Guide
LIRDBSM
1
Do not attempt to disassemble the camera.
If the camera can not work, please contact
local franchiser or our company.
BRIEF OF PRODUCT
* Sensor
Adopt CMOS 1/3" Sensor.
INTRODUCTION
CONNECTING
Monitor
Video
* Auto Gain Control (AGC)
Built-in auto gain control (AGC) circuit. The Colour
camera
can get high definition picture in low Lux condition.
12V DC
LIRDBSM
* Auto Electronic Shutter (AES)
Built-in auto electronic shutter function. The Colour
camera’s AES speed can reach 1/100,000s.
Congratulations on your purchase of this product.
This User Guide suits LIRDBSM product. We adopt the
latest CMOS technical of sensor and driver. The most
attractive characteristics are small and easy hidden, suits
the elevator and corridor. In addition, it owns the
characters of high definition and stability, strong antijamming, rich and real Colour. Fixing and using this model
are convenient too. It is very good for you to apply to
yours CCTV system.
Please read this instruction manual carefully to
ensure proper use of the product.
To prevent fire or shock hazarded. Do not expose the unit
* Gama Characteristic
Camera Gama characteristic is 0.45.
to rain or moisture.
DC12V Power Supply
* Scanning Mode
NTSC or PAL mode.
* Support UTC function
With UTC Remote Controller for the convenience of
OSD menu setting.
Link wire rule:
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
Video
The symbol is intended to alert the user to the presence of
Power
uninsulated ‘dangerous voltage’ within the product’s
enclosure that may be of sufficient Magnitude to
a risk of electric shock to persons.
CAUTION:
RISK OF ELECTRIC. DO NOT OPEN
TROUBLE AND SOLUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole whether exactitude.
. Please check all the connecting cable and monitors whether be connected
correctly or not.
Notes:
DO NOT REMOVE COVER OR BANCK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
CAUTION: TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS,DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply.
. Check the monitor and peripheral equipments used.
Note:
●The power supply must through safe attestation. Its output
voltage,current,voltage polarity and operating temperature must
match the camera’s requirement.
●When using the camera in the thunderbolt condition,please note to
mount Anti-thunder device or put off the power supply plug and cable.
●In order to capture high quality pictures, the power supply’s cable and
video output cable should not be too long.
3. The picture background Colour changes continuously
. The fluorescent lamp’s electromagnetic field cause Colour roll. This is
proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
. The power supply’s voltage unstable.
. Connecting cables not connect correctly or have high impedance.
● Please note the camera’s operating temperature and its using
environment requirement. Avoid using the camera at too high
or too low temperatures. The operating temperature is -30~
+60℃. (Recommendatory operating temperature is –10~
+50℃.)
● Never make the camera face the sun or bright object.
Otherwise, it will damage the CMOS.
● Do not mount the camera near by the radiator or heater.
Download PDF