CS 06 Chassis Slides - Kepco power supplies

INSTRUCTION MANUAL
KEPCO
CS 06
An ISO 9001 Company.
CHASSIS SLIDES MODEL CS 06
1. DESCRIPTION
Chassis Slides Model CS 06 contains the components required to install a pair of chassis slides on Kepco EL Series
Electronic Loads.
CAUTION: Use of components not provided herein may damage the unit and void the warranty.
2. INSTALLATION OF CHASSIS SLIDES
2.1 MATERIAL REQUIRED (SEE TABLE 1.)
TABLE 1. MATERIAL SUPPLIED
MATERIAL
QUANTITY
One pair of slides (includes cabinet, intermediate and chassis
sections), Kepco P/N 108-0475
1
* End bracket
2
* Bar Nut
6
* Machine Screw, 10-32 X 1/2 in. long, Phillips head, Flat head
4
* Machine Screw, 10-32 X 3/8 in. long, Phillips head, Pan Head
12
* Machine Screw 10-32 x 1/4 in. long, PHPH, black, zinc oxide
(Kepco P/N 101-0531) *
7
CS 06 Instruction Sheet 228-1734
1
* Included with P/N 108-0475
KEPCO, INC.
131-38 SANFORD AVENUE
FLUSHING, NY. 11355 U.S.A.
TEL (718) 461-7000
http://www.kepcopower.com
email: hq@kepcopower.com
©2011, KEPCO, INC
Data subject to change without notice
FAX (718) 767-1102
1
228-1734 REV 1
2.2 PROCEDURE (SEE FIGURES 2, 3 AND 4.)
1. The slides are shipped pre-assembled. Press lock button and separate chassis section of each slide from
intermediate section (See Figure 1).
CABINET
SECTION
INTERMEDIATE
SECTION
CHASSIS
SECTION
PRESS LOCK BUTTON TO
SEPARATE CABINET SECTION
FROM INTERMEDIATE SECTION.
3043551
FIGURE 1.
SEPARATE CHASSIS SECTION
2. Attach two chassis sections of slide to each side of Electronic Load using seven black screws (P/N 1010531): four on one side and three on the other side (see Figure 2).
CAUTION: Using screws other than those specified will damage
the unit and void the warranty.
!
MACHINE SCREW (4),
10-32 x 1/4 PH PAN HEAD
(KEPCO P/N 101-0531)
CHASSIS
SECTION
EL SERIES
ELECTRONIC LOAD
CHASSIS
SECTION
MACHINE SCREW (5),
10-32 x 1/4 PH PAN HEAD
(KEPCO P/N 101-0531)
3043550
FIGURE 2.
KEPCO, INC.
2
INSTALLING CHASSIS SECTION ON ELECTRONIC LOAD CHASSIS
131-38 SANFORD AVENUE
FLUSHING, NY. 11355 U.S.A.
TEL (718) 461-7000
http://www.kepcopower.com
email: hq@kepcopower.com
228-1734 REV 1
FAX (718) 767-1102
061711
3. Attach two end brackets to the two cabinet sections of slides using four screws and two bar nuts (see Figure
3). Use appropriate holes to accommodate cabinet.
4. Attach two front cabinet rails to two cabinet sections using four pan head screws and two bar nuts. For flush
mounting use four flat head screws instead of the pan head screws.
5. Attach two rear cabinet rails to two cabinet sections using four pan head screws and two bar nuts.
COUNTERSINK HOLES
OF CABINET MOUNTING
RAIL FOR FLUSH MOUNTING
MACHINE SCREW (2),
10-32 x 1/2 PH
FLAT HEAD
CABINET MOUNTING RAIL,
REAR, LEFT SIDE
(NOT SUPPLIED)
USE APPROPRIATE HOLES
TO ACCOMMODATE CABINET
MACHINE SCREW (3),
10-32 x 3/8 PH
PAN HEAD
END
BRACKET
FLUSH MOUNTING
BAR NUT
MACHINE SCREW (3),
10-32 x 1/2 PH
PAN HEAD
MACHINE SCREW (2),
10-32 x 3/8 PH
PAN HEAD
0.31 IN. CLEARANCE REQUIRED
BEHIND CABINET SECTION TO
ALLOW LOCK BUTTON TO RELEASE.
CABINET
SECTION
3043548
FIGURE 3.
KEPCO, INC.
061711
CABINET MOUNTING RAIL
FRONT, LEFT SIDE
(NOT SUPPLIED)
FOR FLUSH MOUNTING,
SEE DETAIL
ATTACHING END BRACKETS AND CABINET MOUNTING RAILS TO CABINET SECTION
131-38 SANFORD AVENUE
FLUSHING, NY. 11355 U.S.A.
TEL (718) 461-7000
http://www.kepcopower.com
email: hq@kepcopower.com
228-1734 REV 1
FAX (718) 767-1102
3
6. Attach front and rear cabinet mounting rails (with cabinet and intermediate sections of slide attached) to the
cabinet rail (attaching hardware not supplied) (see Figure 4).
!
WARNING!
The load is very heavy (80 - 90 pounds). Exercise care when lifting, mounting or
otherwise handling this product. It is recommended that two or more persons
handle the electronic load.
7. Insert Electronic Load into rack by sliding chassis-mounted slide section into the cabinet-mounted intermediate section).
!
WARNING!
Do not lean on unit when fully extended. Weight added to the fully extended unit in
excess of 35 lbs can cause the slide to fail and the unit to fall.
REAR
CABINET
MOUNTING
RAIL
FRONT
CABINET
RAIL
REAR
CABINET
RAIL
FRONT
CABINET
MOUNTING
RAIL
EL SERIES
ELECTRONIC
LOAD
CABINET
SECTION
CHASSIS
SECTION
3043549
FIGURE 4.
KEPCO, INC.
4
INTERMEDIATE
SECTION
ATTACHING CABINET SECTION TO RAIL
131-38 SANFORD AVENUE
FLUSHING, NY. 11355 U.S.A.
TEL (718) 461-7000
http://www.kepcopower.com
email: hq@kepcopower.com
228-1734 REV 1
FAX (718) 767-1102
061711
Download PDF