100908 VSUC4RK INS_Bi

READ & SAVE THESE INSTRUCTIONS!
INSTALLATION INSTRUCTIONS
Video Door Answering System
Model VSUC4RK
INSTALLATION INSTRUCTIONS
This booklet contains information for installing the TV/Monitor.
All system wiring and rough-in frames should be installed
before mounting and wiring the master station. Refer to the
installation instructions packaged with the rough-in frames
for detailed wiring information.
For more detailed information on wiring and mounting other
system components (i.e., optional camera, rough-in.), refer
to the installation instructions packaged with the separate
components.
Caution
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR
MOISTURE.
THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING
OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS,
SUCH AS VASES, SHALL BE PLACE ON THE APPARATUS.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninstalled “dangerous voltage” within the product’s enclosure. This voltage may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult and electrician for replacement of the obsolete outlet.
2) Keep these instructions.
3) Heed all warnings.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
4) Follow all instructions
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
11) Only use attachments/accessories specified by the manufacturer.
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
12) Unplug the apparatus during lighting storms or when
unused for long period of time.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
13) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen
into apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been
dropped.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade
PRECAUTIONS
Installation ________________________
SAFETY ________________________________________
Do not install the unit in an extremely hot or humid place or
in a place subject to excessive dust or mechanical vibration.
Should any liquid or solid object fall into the cabinet, unplug
the unit and have it checked by the qualified personnel
before operating it any futher.
The unit is not designed to be waterproof
Cleaning __________________________
Unplug the unit from the wall outlet if it is not going to be
used for several days or more. To disconnect the cord, pull it
out by the plug. Never pull the cord itself.
Clean the unit with a dry soft cloth. Never use strong solvents such as thinner or benzine as they might damage the
finish of the unit.
Allow adequate air circulation to prevent internal heat buildup. Do not place the unit on surfaces (rugs, blankets, etc.) or
near materials (curtains, draperies) that may block the ventilation holes.
2
IMPORTANT SAFETY INSTRUCTIONS
1.
READ THESE INSTRUCTIONS — All the safety and
operating instructions should be read before the product
is operated.
2.
RETAIN INSTRUCTIONS — The safety and operating
instructions should be retained for future reference.
3.
HEED ALL WARNINGS — All warning on the product
and in the operating instructions should be adhered to.
4.
FOLLOW ALL INSTRUCTIONS — All operating and use
instructions should be followed.
5.
CLEANING — Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol.
Use a dry cloth for cleaning.
6.
ATTACHMENTS — Do not use attachments not recommended by the product manufacturer, as they may cause
hazards.
7.
WATER AND MOISTURE — Do not use this product
near water—for example, near a bath tub, wash bowl,
kitchen sink, laundry tub, in a wet basement, near a
swimming pool, and the like.
8.
ACCESSORIES — Do not place this product on an
unstable cart, stand, tripod bracket, or table. The product
may fail, causing serious injury to a child or adult, and
serious damage to the product. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the
product should follow the manufacturer’s instructions, and
should use a mounting accessory recommended by the
manufacturer.
9.
A product and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the product and cart combination to overturn.
will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug still cannot be
inserted, contact your electrician to replace you obsolete
outlet. Do not defeat the safety purpose of the polarized
plug.
13. POWER-CORD PROTECTION — Power-supply cords
should be routed so that they are not likely to be walked
on or pinched by items placed upon or against them paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
14. PROTECTIVE ATTACHMENT PLUG — The product is
equipped with an attachment plug having overload protection. This is a safety feature. See instruction Manual for
replacement of, or resetting the protective device. If
replacement of the plug is required, be sure the service
technician uses a replacement plug specified by the manufacturer that has the same overload protection as the
original plug.
15. OUTDOOR ANTENNA GROUNDING — If an outside
antenna or cable system is connected to the product, be
sure the antenna or cable system is grounded so as to
provide some protection against voltage surges and builtup static charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information with regard to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, an
requirements for the grounding electrode (Refer to the figure on page 4).
16. LIGHTNING — For added protection of the product during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This
will prevent damage to the product due to lightning and
power-line surges.
10. VENTILATION — Slots and openings in the cabinet are
provided for ventilation and to ensure reliable operation of
the product.
They protect it from overheating, and these openings
must not be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in built-in installation such as a bookcase or
rack unless proper ventilation is provided, or the manufacturer,s instructions have been adhered to.
17. POWER LINES — An outside antenna system should not
be located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits.
18. OVERLOADING — Do not overload wall outlets, extension cords, or integral convenience receptacles, as this
can result in a risk of fire or electric shock.
11. POWER SOURCES — This product should be operated
only from the type of power source indicated on th marking label. If you are not sure of the type of power supply
in your home, consult your product dealer or local power
company. For products intended for operation from battery power or other sources, refer to operating instructions.
19. OBJECT AND LIQUID ENTRY — Never push objects of
any kind into the product through openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the product.
12. GROUNDING OR POLARIZATION — This product may
be equipped with a polarized alternating current line plug
(a plug having one blade wider than the other). This plug
20. SERVICING — Do not attempt to service this product
yourself as opening or removing covers my expose you to
3
dangerous voltage or other hazards. Refer all servicing to
qualified service personal.
F. When the product exhibits a distinct change in performance — this indicates a need for service.
21. DAMAGE REQUIRING SERVICE — Unplug this product
from the wall outlet and refer servicing to qualified service
personnel under the following conditions.
22. REPLACEMENTS PARTS — When replacement parts
are required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the sam characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
A. When the power-supply cord or plug is damaged.
B. If liquid has been spilled, or objects have fallen into the
product.
23. SAFETY CHECK — Upon completion of any service or
repairs to this product, ask the service technician to perform safety checks to determine that the product is in
proper operating condition.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following
the operation instructions. Adjust only those controls
that are covered by the operating instruction, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation.
24. WALL OR CEILING MOUNTING — The product should
be mounted to a wall or ceiling only as recommended by
the manufacturer.
25. HEAT — The product should be situated away from heat
sources such as radiators, heat resistors, or other products (including amplifiers) that produce heat.
E. If the product has been dropped or damaged in any
way.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUNDING CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC-NATIONAL ELECTRICAL CODE
4
Table of Contents
VSUC4RK REPRESENTATIVE WIRING ILLUSTRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Contents of carton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Precautions and Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Wiring Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
AM Antenna Installation and Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8
FM Antenna Installation and Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-11
Optional FM Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
TV Antenna/Cable System Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Telephone Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Camera Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Maximum Number of Camera’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Wiring and Mounting the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13
Connecting Camera 1 at the TV/Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting Optional Camera 2 at the TV/Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Wiring and Mounting the TV/Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-17
Powering up the System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Camera Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Camera Lens Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
5
VSUC4RK SERIES REPRESENTATIVE WIRING ILLUSTRATION
¨
INSTALLATION
¨
¨
CONTENTS OF CARTON
¨
Check (_) for following VSUC4RK carton contents:
¨
¨
¨
¨
VSUC4RK TV/Monitor
¨
VSUC4RK Hardware bag assembly containing:
¨
(4) #8 x 1 1/2" screws
¨
(4) #8 x 1 1/4" screws
¨
(4) #8 x 7/8" screws
¨
(4) #8 x 2 1/4" screws
(4) #8 x 1 1/2" screws
(4) #8 threaded mounting shafts
(4) 1/4" spacers
(4) 1/2" spacers
¨
¨
(4) 3/4" spacers
VSC4R Camera
VSC4R Hardware bag assembly containing:
(2) #6 x 1 1/2" screws
(2) #6 x flat washers
6
AM loop Antenna with 34" lead
FM Antenna with 20 foot lead
FM Antenna with 5 foot lead
FM Antenna Balun
TV right angle coax extension
Telephone cable
IR Remote Control with battery
Mounting Hole Template
Homeowner’s manual
Installation Instructions
Registration Card
Note to Installer: Do not discard these installation instructions. Please give all installation
instructions, warranty registration and homeowner’s manual to homeowner.
PRECAUTIONS AND GUIDELINES
The NuTone VSUC4RK has been designed for ease of installation. Please read and follow ALL installation instructions,
guidelines and precautions. Any deviation from these instructions or miswiring combinations will cause the unit to fail and
all NuTone warranties will be void.
WARNING: 120 Volt AC power to the VSUC4RK TV/Monitor must remain unplugged
until all system wiring at the TV/Monitor and camera is complete.
•
Observe all local regulations and codes in your area.
•
All screw terminals at the camera and TV/Monitor must be secure.
•
Observe all color codes of wires when connecting camera to TV/Monitor.
•
The VSUC4RK and camera is designed to be used with category 5 or category 6; no other cable should be used.
The use of wire other than category 5 or category 6 cable will void all NuTone warranties and may result in
faulty installation and improper operation.
•
The door camera must not be mounted in an area that would be subject to direct sunlight or a strong reflection from the sun.
Wiring Specifications
The following cables must be installed to complete the installation. Depending on the type of installation, these cables
may be installed during framing (new construction) or in an existing home. For new construction it is important to determine the final location of the TV/Monitor and Camera so all needed cables can be ran before finished walls are installed.
An existing home will require cables to be “fished” to the TV/Monitor and camera locations.
• Use category 5 or category 6 cable for connecting:
• VSC4R camera to TV/Monitor: 250 ft maximum
• Optional second camera to TV/Monitor (NuTone Models VSC4R and VSC4S): 250 ft maximum
• Use the supplied AM antenna to connect to the AM antenna terminals on the TV/Monitor.
• Use either of the supplied FM antennas to connect to the FM antenna on the TV/Monitor. An optional (not supplied
by NuTone) FM antenna can be connected using RG-6 coax cable between FM antenna and FM connector on
TV/Monitor.
• Use RG-6 coax cable to connect TV antenna, or cable system to TV connector on TV/Monitor.
• Use supplied telephone cable to connect the phone jack to the TEL jack on TV/Monitor.
• Be certain a standard 120 VAC duplex outlet is located within reach of the power cord supplied with the TV/Monitor
(less than 6 ft).
AM Antenna Installation and Connection
The VSUC4RK is supplied with one AM radio antenna.
AM Loop Antenna
The loop antenna with 60" lead is designed to be mounted inside the
home. The loop antenna is installed after the cabinets have been
installed. Typically the loop antenna is mounted under the cabinet next to
the TV/Monitor, above the cabinet if the top of the cabinets is accessible,
or inside the cabinet. Experiment with the antenna orientation and placement to optimize AM radio reception.
7
Under the Cabinet Mounting
Fasten the plastic frame of the loop antenna using screws, nails, or staples (not supplied) in an open space under
the cabinet. Attach the two wire lead-in cable from the loop antenna to the AM-ANT terminals on the back of the
TV/Monitor.
Above the Cabinet Mounting
Fasten the plastic frame of the loop antenna using screws, nails, or staples (not supplied) in an open space above
the cabinet. Run the two wire lead-in cable behind the cabinet to the TV/Monitor location. If access behind the cabinet is not possible, drill a small hole in the top and bottom of the cabinet and “fish” the two wire lead-in cable through
the cabinet to the TV/Monitor location. Attach the two wire lead-in cable from the loop antenna to the AM-ANT terminals on the back of the TV/Monitor.
In the Cabinet Mounting
Fasten the plastic frame of the loop antenna using screws, nails, or staples (not supplied) in an open space inside
the cabinet. Drill a small hole in the bottom of the cabinet and “fish” the two wire lead-in cable through the cabinet to
the TV/Monitor location. Attach the two wire lead-in cable from the loop antenna to the AM-ANT terminals on the
back of the TV/Monitor.
FM Antenna Installation and Connection
The VSUC4RK is supplied with two different FM radio antennas. Use the antenna that best suits your installation
8
FM Folded Dipole Antenna with 20 foot lead-in
The folded dipole antenna with a 20' lead is designed to be mounted in the homes attic. If additional lead-in length is
needed, additional 300 ohm “twin lead” cable can be attached. Use one of the following methods to install the FM
antenna.
Stapling
Use staples to attach twin lead wire to rafters, or joists. Insert the staple lengthwise in the plastic between the wires.
Do not staple across the wire.
Staple
Antenna
Through
Center
Nailing
Nails may be used to attach the twin lead wire to rafters or joists. Place nails in the plastic between the two wires.
Do not nail over or through a wire. Do not wrap the twin lead wire around a nail.
Nails may be used to attach the plastic center block and the two plastic end caps. Use nail holes provided in these
pieces.
Center Block
Nail
Antenna
Through
Center
Nail Holes
End Cap
Attic Rafter
Staple antenna to attic rafters horizontally.
Nail a 5 foot piece of scrap board horizontally between rafters to provide a clear span of 60". Nail the center block of
the center of the board. Staple antenna leads to board.
9
Ceiling Joist
When attic space is limited, staple antenna to ceiling joists.
Nail or Staple Through Center
Twin-Lead Connection
1. Run the 20 foot twin lead to the location where the TV/Monitor will be mounted.
2. Keep twin lead at least 12" away from metal and other wiring.
3. Provide 12" extra of antenna lead at the TV/Monitor location.
4. Attach the lead-in cable terminals of the antenna to the screw terminals of the FM antenna balun (supplied). Plug
the FM antenna balun into the FM-ANT connector on the back of the TV/Monitor.
FM Antenna with 5 foot lead-in
The antenna with a 5' lead is designed to be mounted inside the home. This antenna is installed after the cabinets
have been installed. Typically the antenna is mounted under the cabinet, above the cabinet if the top of the cabinets
is accessible, or inside the cabinet. Experiment with the antenna orientation and placement to optimize FM radio
reception. For best radio reception, extend the antenna and lead-in to its full length.
Under the Cabinet Mounting
Fasten the FM antenna using staples (not supplied) in an open space under the cabinet. Plug the FM antenna “F”
connector into the FM-ANT “F” connector on the back of the TV/Monitor.
Important: The staples used to mount the FM antenna must not have enough force to pierce the wire insulation or
break the antenna lead. Test the staple installation in an inconspicuous spot on the cabinet before actual mounting
of the FM antenna.
10
Above the Cabinet Mounting
Fasten the FM antenna using staples (not supplied) in an open space above the cabinet. Run Antenna behind the
cabinet to the TV/Monitor location. If access behind the cabinet is not possible, drill a hole in the top and bottom of
the cabinet and “fish” antenna through the cabinet to the TV/Monitor location. Plug the FM antenna “F” connector
into the FM-ANT connector on the back of the TV/Monitor.
Important: The staples used to mount the FM antenna must not have enough force to pierce the wire insulation or
break the antenna lead. Test the staple installation in an inconspicuous spot on the cabinet before actual mounting
of the FM antenna.
In the Cabinet Mounting
Fasten the FM antenna using staples (not supplied) in an open space inside the cabinet. Drill a hole in the bottom of
the cabinet and “fish” antenna through the cabinet to the TV/Monitor location. Plug the FM antenna “F” connector
into the FM-ANT “F” connector on the back of the TV/Monitor.
Important: The staples used to mount the FM antenna must not have enough force to pierce the wire insulation or
break the antenna lead. Test the staple installation in an inconspicuous spot on the cabinet before actual mounting
of the FM antenna.
Optional FM Antenna Connection (not supplied by NuTone)
An optional FM antenna (not supplied by NuTone) can be connected to the TV/Monitor. Follow the direction supplied
by the antenna manufacture when locating and mounting the antenna. Used RG-6 coax cable to connect the antenna to the FM-ANT “F” connector on the back of the TV/Monitor. Be certain to following all safety guideline supplied
by the antenna manufacture and in these instructions.
TV Antenna/Cable System Connection
Use RG-6 coax to connect between the VHF/UHF antenna or cable system to the “F” fitting right-angle coax adapter.
Plug the right-angle adapter into the TV-ANT “F” connector on the back of the TV/Monitor. Be certain to following all
safety guideline supplied by the antenna manufacture, cable TV supplier and in these instructions.
11
Telephone Connection
Plug the telephone cable (supplied) to the incoming telephone line jack and the TEL jack on the back of the TV/Monitor.
Camera Wiring
An individual category 5 or category 6 cable must be connected from the camera to the TV/Monitor.
• Maximum cable length: 250 feet.
• Cable type: Category 5 or category 6
IMPORTANT: NuTone cannot be responsible for improper system operation that results from
interference generated by light dimmers, fluorescent lighting fixtures, and similar electrical
products. Such interference must be corrected at the source.
TO HELP REDUCE THIS INTERFERENCE, ALL WIRING CONNECTED BETWEEN THE CAMERA
AND TV/MONITOR MUST BE PLACED AT LEAST 12 INCHES FROM ANY A.C. POWER WIRING.
AVOID RUNNING INTERCOM WIRES PARALLEL TO A.C. POWER WIRING.
Maximum Number of Camera’s
The VSUC4RK is supplied with one (1) VSC4R camera. An optional second camera; NuTone model VSC4R recessed
mount camera, or VSC4S surface mount camera can be added.
IMPORTANT: Never use any camera other than NuTone models VSC4R and VSC4S or the
TV/Monitor will be damaged.
Wiring and Mounting the Camera
1. The VSC4R recessed camera is designed to mount in the VRC4R rough-in frame (purchased separately) at the time
of framing construction. At the same time the rough-in is installed, the category 5 or category 6 cable should be ran
from the camera rough-in location to the monitor location. Please refer to the instructions supplied with the VRC4R
rough-in and VSC4R camera, for mounting and wiring information.
2. At the VRC4R rough-in location, strip approx 2" of outer protective jacket from the category 5 or category 6 cable.
12
3. Separate and strip approx. 1/2" of insulation from each of the eight wires in the cable. Twist the following cables
together:
• OR and OR/WH
• GR and GR/WH
• BL and BL/WH
• BR and BR/WH
4. Attach each of the twisted pair of wires to the corresponding terminal on the back of the camera. Tighten each screw
securely.
5. Dress extra cable and position camera into rough-in.
6. Fully seat the camera into the rough-in. Open the upper and lower access doors. Attach the camera to the rough-in
using a #6 x 1 3/4" screw (supplied) and flat washer (supplied) at both the top and bottom of the camera. Level the
camera, tighten screws and close upper and lower access doors the master station panel faced down to connect
wiring.
Important: If camera is exposed to outside elements, caulk should be added to the top and sides of the camera at
the wall surface. Do not caulk bottom surface.
Mounting Screw
and flat washer
13
Connecting Camera 1 at the TV/Monitor
1. Strip approx 2" of outer protective jacket from the category 5 or category 6 cable.
2. Separate and strip approx. 1/2" of insulation from each of the eight wires in the cable. Twist the following cables
together:
• OR and OR/WH
• GR and GR/WH
• BL and BL/WH
• BR and BR/WH
3. Attach each of the twisted pair of wires to the corresponding Camera 1 screw terminals on the back of the TV/Monitor.
Tighten each screw securely.
Connecting Optional Camera 2 at the TV/Monitor
If an optional second camera has been installed, use the following connection procedure.
1. Strip approx 2" of outer protective jacket from the category 5 or category 6 cable.
2. Separate and strip approx. 1/2" of insulation from each of the eight wires in the cable. Twist the following cables
together:
• OR and OR/WH
• GR and GR/WH
• BL and BL/WH
• BR and BR/WH
3. Attach each of the twisted pair of wires to the corresponding Camera 2 screw terminals on the back of the
TV/Monitor. Tighten each screw securely.
14
Wiring and Mounting the TV/Monitor
Locate the TV/Monitor unit where the camera, TV, AM, FM and Telephone cables were previously ran. Depending on
the depth of the cabinet, decide if you need to make all the connections to the back of the TV/Monitor before fastening
the TV/Monitor to the bottom of the cabinet. The method and type of mounting hardware using to attaching the
TV/Monitor will very depending on your installation. Decide which mounting hardware to use based on the following
instructions.
Using #8 wood screws
• From underneath the cabinet, position the mounting hole template and mark the mounting hole locations.
• From underneath the cabinet, drill a 3/32" hole at each of the marked mounting hole locations (do not drill complete
thru into the inside of the cabinet).
• Measure the distance between the frame of the cabinet and the bottom of the cabinet. Combine the supplied 1/4",
1/2" and 3/4" round plastic spacers so they will fill the space between the bottom of the cabinet and the frame of
the cabinet.
• Depending on the depth of the cabinet, decide if you need to make all the connections to the back of the
TV/Monitor before fastening the TV/Monitor to the bottom of the cabinet.
• Position the round plastic spacer at each mounting hole location. To help hold the spacers in-place, position the
small diameter end of the spacer towards the TV/Monitor case. Lift and hold the TV/Monitor in position. Select a
7/8", 1 1/4", or 1 1/2" mounting screw (supplied) based on your particular installation and insert the first mounting
screw into one of the mounting holes in the TV/Monitor, and tighten.
15
• Insert the remaining 3 mounting screws (supplied) and tighten.
• Complete all the connections on the back of the TV/Monitor, if they were not made before attaching the TV/Monitor
to the cabinet.
Using #8 Machine Screws and Threaded Mounting Shafts
• From underneath the cabinet, position the mounting hole template and mark the mounting hole locations.
• From underneath the cabinet, drill a 3/16" hole at each of the marked mounting hole locations. Counter sink holes
from inside cabinet to make screw head flush with cabinet surface.
• Measure the distance between the frame of the cabinet and the bottom of the cabinet. Combine the supplied 1/4",
1/2" and 3/4" round plastic spacers so they will fill the space between the bottom of the cabinet and the frame of
the cabinet.
• Depending on the depth of the cabinet, decide if you need to make all the connections to the back of the
TV/Monitor before fastening the TV/Monitor to the bottom of the cabinet.
• Select a 1 1/2", or 2 1/4" mounting screw (supplied) based on your particular installation. Insert all four (4) mounting screws (supplied) from inside the cabinet.
16
• Position the round plastic spacer at each mounting hole location. To help hold the spacers in-place, position the
small diameter end of the spacer towards the TV/Monitor case. Lift, align the screws onto the spacers and hold the
TV/Monitor in position.
• Insert the first threaded mounting shaft (supplied) into the bottom of the TV/Monitor, and tighten using a flat blade
screw driver.
• Insert the remaining 3 threaded mounting shafts (supplied) and tighten.
• Complete all the connections on the back of the TV/Monitor, if they were not made before attaching the TV/Monitor
to the cabinet.
Powering Up the System
Once all connections throughout the system have been checked, the power cable plug can be plugged into a 120 VAC
duplex outlet. Refer to the homeowner’s manual for operating instructions.
17
Camera Volume Adjustment
The VSC4R door camera is provided with a volume level adjustment set screw. The adjustment has been pre-set at the factory to provide the optimal volume level at the door camera. The volume level can be adjusted if your specific application
requires the level to be either increased or decreased. Insert a jeweler’s screwdriver into the small hole that is shown in the
camera illustration. Rotate the small set screw to adjust the volume level.
Important: Do not use excessive force to rotate the screw. Damage could occur to the camera, and loss of audio may
result. Use extreme caution when making the adjustment. Do not use a screwdriver that is too big for the application.
VSC4R
Volume Adjustment
Camera Lens Manual Adjustment
The VSC4R door camera is provided with a manual camera lens adjustment. The adjustment can be used to fine tune the
angle of the camera lens to compensate for installations that are not directly in line to the viewing area. The adjustment is
located on the back of the camera, as shown in the camera illustration. Move the adjustment control upward to lower the
camera lens. Move the adjustment control downward to raise the camera lens. The control can also be moved left or right to
adjust the side angle. Adjust the camera lens position to provide the best viewing area for your installation.
VSC4R
Lens Adjustment
18
FCC Information Part 15 Rules
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
FCC Warning – This equipment may generate or use radio frequency energy. Changes or modifications to this equipment
may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could
lose the authority to operate this equipment if an unauthorized
change or modification is made.
FCC Warning – Changes or modifications not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
The serial number of this product may be found on the rear side
of the product. No others have the same serial numbers as
yours. You should record the number and other vital information
here and retain this book as a permanent record of your purchase to aid identification in case of theft.
FCC Information Part 68 Rules
telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance
notice isn’t practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is
necessary.
The telephone company may make changes in its facilities,
equipment, operations or procedures that could affect the
operation of the equipment. If this happens the telephone
company will provide advance notice in order for you to
make necessary modifications to maintain uninterrupted
service.
If trouble is experienced with this equipment for repair or
warranty information, please contact NuTone Inc. 4820 Red
Bank Road, Cincinnati, Ohio 45227 or dial 1-800-543-8687
or visit www.nutone.com. If the equipment is causing harm to
the telephone network, the telephone company may request
that you disconnect the equipment until the problem is
resolved.
This equipment is of a type that is not intended to be
repaired by the user.
This equipment must not be used on party lines. Connection
to party line service is subject to state tariffs. Contact the
state public utility commission, public service commission or
corporation commission for information.
This equipment complies with Part 68 of the FCC rules and
the requirements adopted by the ACTA. On the back side of
the display of this equipment is a label that contains, among
other information, a product identifier in the format US:
RICTE08BVSUC4. If requested, this number must be provided to the telephone company.
The Universal Service Order Codes (“USOC”) for this equipment is a standard RJ11C jack. A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules
and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It
is designed to be connected to a compatible modular jack
that is also compliant.
The REN is used to determine the number of devices that
may be connected to a telephone line. Excessive RENs on a
telephone line may result in the devices not ringing in
response to an incoming call. In most but not all areas, the
sum of RENs should not exceed five (5.0). To be certain of
the number of devices that may be connected to a line, as
determined by the total RENs, contact the local telephone
company. The REN for this product is 0.8B.
If this equipment causes harm to the telephone network, the
This product meets the applicable Industry Canada technical specifications.
may consist of any combination of devices subject only
to the requirement that the sum of the RENs of all the
devices does not exceed five’’. The Ringer Equivalence
Number for this device is 0.8
‘’The Ringer Equivalence Number is an indication of the
maximum number of devices allowed to be connected to
a telephone interface. The termination on an interface
19
Product specifications subject to change without notice.
4820 Red Bank Road, Cincinnati, Ohio 45227
Printed in Korea, Rev. 09/2005, Part No. 100908
Download PDF