698-960 / 1695-2690 / 1695-2690 MHz 6880300

698-960 / 1695-2690 / 1695-2690 MHz
6880300
Project Design Requirement
Issue D 2014-11-24





6880300A 6880300G
Triple Band Antenna, dual polarisation, 6 connectors
Independent tilt on each band 0°-10° / 0°-10° / 0°-10°
UltraLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Single RET module to control all tilt angles,
fully inserted inside the antenna (field replaceable)
XXXpol / 65° Az
17.5 / 18.5 / 18.5 dBi
0-10 / 0-10 / 0-10 °
2696 x 305 x 162 mm

Model number options:
6880300
6880300A
6880300G
Manual Electrical tilt Antenna
Remote Electrical Tilt Antenna (AISG1.1)
Remote Electrical Tilt Antenna (3GPP/AISG2.0)
Access Ports Description (Connectors)
The Antenna has 6 connectors located at its bottom face and marked with colour rings. See photo next page.
Ed D 2014-11-24 - page 1/2 - We reserve the rights to modify our products without prior notice - Several patents pending regarding this product.
Ultra Low Band:
698-960 MHz ports
2 x 7-16 DIN female Long Neck
Ultra Wide Band:
1695-2690 MHz ports
2 x 7-16 DIN female Ultra Long Neck
Ultra Wide Band:
1695-2690 MHz ports
2 x 7-16 DIN female Ultra Long Neck
Electrical Characteristics
Frequency Bands
Gain (dBi)
tilt 0°
tilt 5°
tilt 10°
R1
Y1
Y2
700
800
900
1800
2100
15.5
15.5
15.2
16.5
16.4
16.2
17.4
17.3
17.0
17.7
17.7
17.6
18.1
17.9
17.8
Input Impedance
2600
18.3
18.1
17.7
1800
2100
2600
17.7
17.7
17.6
18.1
17.9
17.8
18.3
18.1
17.7
50 ohms
50 ohms
VSWR
<1.5
<1.5
50 ohms
<1.5
Polarisation
±45°
±45°
±45°
Horizontal Beamwidth (-3 dB)
73°
67°
67°
65°
65°
65°
65°
65°
65°
Vertical Beamwidth (-3 dB)
8.6°
7.5°
6.7°
6.1°
5.3°
4.2°
6.1°
5.3°
4.2°
Electrical Downtilt range
0° to 10°
0° to 10°
Inter/Intra Band Isolation
>25dB
>25dB
>28dB
18 dB typ.
18 dB typ.
18 dB typ.
Front to back @180°+/-30°
>25 dB
>25 dB
>25 dB
Maximum Power (per port)
250 W
200 W
200 W
<-110 dBm
<-110 dBm
<-110 dBm
Upper Sidelobe Rejection
(20° sector above main beam)
Intermodulation
3rd order for 2 x 20 W carriers
0° to 10°
Electrical Downtilt Control
Electrical downtilt can be controlled separately for R1, Y1 and Y2 arrays.
The three tilt indicators are covered by a removable transparent cap.
Manual control: A coloured knob at the end of the tilt indicator allows change of the tilt without need for
a tool. Knob colour is identical to connector colours as defined above. To access the knob, the cap is
removed by turning it counter clockwise. It is re-installed by opposite rotation.
Remote control: The remote control of the electrical tilt is managed by a module (MDCU) totally inserted
at the bottom of the antenna. One single module controls individually the tilt of each band (no need of
daisy chain cables between the bands). For RET control, the transparent cap must be in place and locked.
This module does not add any additional length at the bottom of the antenna. The tilt angle indicator stays
always visible and the antenna still has manual tilt control (manual override).
RET module part number
(one only needed per antenna)
MDCU-A0000
MDCU-G0000
for AISG1.1 protocol (one unit included in 6880300A)
for 3GPP/AISG2.0 protocol (one unit included in 6880300G)
Environmental
Operating Temperature Range
Environmental
RoHS compliant
-40°C to +60ºC
ETS 300 019
Yes
w w w. a m p h e n o l -a n t e n n a s . co m
698-960 / 1695-2690 / 1695-2690 MHz
6880300
Project Design Requirement
Issue D 2014-11-24
6880300A 6880300G
Mechanical Characteristics
Dimensions (see drawing)
Height: 2696 mm Width: 305 mm Depth: 162 mm
Weight
29 kg (excluding mounting accessory)
Shroud
Outdoor plastic, Grey RAL7035
Wind Speed
Operational: 160 km/h
Wind load at 150 km/h
Frontal: 1032 N
Packaging
Carton box
2.95 x 0.40 x 0.28 m
0.243 m3 33.5 kg
Survival: 200 km/h
Lateral: 469 N
Rear: 1011 N
Mounting Kit Options (These installation accessories must be ordered separately)
Part number
Weight
Brackets for pole 48 to 115 mm
Description
0900393/00
5.1 kg
Brackets for pole 70 to 150 mm
0900501/00
5.8 kg
Kit to add mechanical tilt (0° to 10°) to above brackets
0900394/00
3.1 kg
Wall mounting brackets with azimuth pan
0900395/00
2.3 kg
Wall mounting brackets with mechanical tilt and azimuth pan
0900533/00
4.4 kg
Ed D 2014-11-24 - page 2/2 - We reserve the rights to modify our products without prior notice - Several patents pending regarding this product.
Antenna bottom
Installation
Tilt indicator covered by a transparent cap.
Manual adjustment is accessed by removing the cap.
Knob colour is same as connectors.
For RET control, the cap must be in place.
Always attach the antenna by its 2 mounting points.
Do not install the antenna with the connectors
facing upward.
Location of the MDCU for RET control
Dimensions (in mm)
w w w. a m p h e n o l -a n t e n n a s . co m
Download PDF