SV10 LED
T
he US manufactured SV10 LED is
the brightest thru hull LED underwa-
ter light available to owners of GRP and
wood boats. The industry leading SV10
combines the unique qualities of the
latest high density LED chip technology
with a silicone optic. This silicone optic
increases the light output 30% while
protecting the LED's from moisture. Both
technologies are incorporated into the
proven SV10 light body. As with all thru
hull lights servicing and maintenance
can be completed from inside the boat
so this task is not limited to haul out
periods. This light is suitable for all mid
to large vessels including Yachts, sport
fishers and cruising boats that have
available A/C power.
SV10 LED technical specifications
Application for: GRP / fiberglass / wood hulls
––––––––––––––––––––––––––––––––––––––––––––––
Light source:
High density LED array
––––––––––––––––––––––––––––––––––––––––––––––
Available in:
White, blue, green, red or RGB
––––––––––––––––––––––––––––––––––––––––––––––
Life length:
Approx. 40,000 + hours
––––––––––––––––––––––––––––––––––––––––––––––
Lumens:
14,630
––––––––––––––––––––––––––––––––––––––––––––––
Kelvin colour temp: 7000
––––––––––––––––––––––––––––––––––––––––––––
Glass lens:
Borosilicate glass
Thickness:
12.7mm / 0.5”
Diameter:
58mm / 2.3”
––––––––––––––––––––––––––––––––––––––––––––––
Power supply:
100 – 277 VAC
50/60 Hz, 1.1 – 0.45 Amp input
Max. 150W output
––––––––––––––––––––––––––––––––––––––––––––––
Casing material: Marine Bronze / Marine Aluminum
Dimensions:
Flange diameter: 130mm (5.12”)
Body length: 258mm (10.16”)
––––––––––––––––––––––––––––––––––––––––––––––
Angles Available: Flush
––––––––––––––––––––––––––––––––––––––––––––––
Code:
SV10 LED
––––––––––––––––––––––––––––––––––––––––––––––
Total shipping weight: 18lbs
––––––––––––––––––––––––––––––––––––––––––––––
Installation: Recommended at minimum 10” (250mm)
below light load waterline between 3 – 8 feet
(1 – 2.5 meters) apart.
4” (100mm) cut out hole
This is a guideline only, for specific requirements please
contact us.
———————————————————————
All information is subject to change without prior notice,
please confirm details prior to ordering.
1881 W State Road 84, Bay 102, Fort Lauderdale, FL 33315 USA
T. 954 760 4447 Toll Free 1 866 772 0130 F. 954 525 3261
sales@seavision.com www.seavision.com
SV10 LED
Underwater Light
Thru-Hull Mount, LED Array
Introduction:
Congratulations on the purchase of your new thru-hull LED underwater light. The platform for the SV10 LED is based upon our
time-proven thru hull SV10 HID housing. Underwater Lights® USA, LLC takes pride in providing well designed, high quality and
thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be installed on your vessel for
aesthetics, to attract fish and/or for security and safety.
General Information:
The latest commercial grade “COB” High-Density Light Emitting Diode (LED) technology used in this light will provide robust and
reliable operation under normal operating conditions when used with the matching Underwater Lights® USA, LLC driver box.
The internal parts for the SV10 LED can be retro-fitted into an SV10 HID housing. Please see the matching SV10 LED retrofit
manual for details.
The SV10 LED is equipped with thermally protected circuitry and can be operated above or below the waterline. Optimum
performance and longevity will be achieved when operating underwater.
The SV10 LED is intended for use on fiberglass and wood hulled vessels.
The main body is designed and tested to act as a cofferdam for added security.
Depending upon water clarity conditions, the light beam can reach up to 30 meters (100 feet).
Safety Information:
Never try to install or remove the SV10 while the vessel is in the water.
Upon proper installation, the SV10 requires bonding to the vessels grounding and cathodic protection system.
Always disconnect and lock-out power before working on light.
Care and Maintenance:
The SV10 should be inspected for moisture every six months by removing the projector lid and inspecting internal components. This
can be accomplished while the vessel is in the water.
The SV10 electrical cabling and driver box should be visually inspected for proper operating condition every six months.
Marine growth should be removed from the glass using a soft brush to allow both heat and illumination to properly exit the light.
Technical Specifications:
Light source = Instant-on high flux, high density LED array - 14,630 maximum Lumens and 7000 Kelvin color temperature in White
- Available in Blue, Green, Red or RGB changing LED array’s - 40,000+ hours life - Internal thermal limit and reverse polarity
protection included
Lense = Borosilicate glass - 12.7mm (0.5”) thick - 58mm (2.3”) diameter net aperture
Overall Dimensions = 130mm (5.12”) diameter x 254mm (10”) long - 5.9 kilograms (13.2 pounds)
Construction = Marine bronze and black anodized marine aluminum alloy
Power supply = VAC to driver box and VDC to SV10 LED (See matching Underwater Lights® USA, LLC driver box specifications)
Troubleshooting:
Please contact our Florida technical support staff at 1-954-760-4447 or French technical support staff at +33 (0) 497 21 0296,
Monday thru Friday from 8:00 am to 5:00 pm local time.
Warranty:
Underwater Lights® USA, LLC warrants this light to be free from defects in workmanship and materials for a period of two years
from the date of original purchase. Further, misuse, abuse, improper installation, neglect, improper shipping, damage caused by
disasters such as fire, flood and lightning, unauthorized repair or modifications will void said warranty. Should your light prove
defective during the warranty period, promptly contact Underwater Lights® USA, LLC for an RMA number and then return the light
freight prepaid with the RMA number clearly marked on the outside of the shipping container.
Underwater Lights USA, LLC
1881 W State Road 84, Bay 102
Fort Lauderdale, FL 33315 USA
Phone: 1-954-760-4447
Fax: 1-954-525-3261
Internet: www.seavision.com
Email: sales@seavision.com
DOC:062212-1
Underwater Lights Europe Sarl
16, rue Rouaze
06400 Cannes, France
Phone: 33-(0)-4-97-21-02-96
Fax: 33-(0)-4-97-21-10-96
Internet: www.seavision.com
Email: sales@seavisioneurope.com
SV10 LED
Underwater Light
Thru-Hull Mount, LED Array
Installation:
The SV10 LED underwater light should be installed by qualified personnel only. It is recommended to mount the light assembly at a minimum of
250-300mm (10-12”) below the light load water line using proper tools and materials. The minimum hull thickness is 10mm (0.4”) and maximum
(for sufficient heat dissipation) is 90mm (3.5”) with an access area of at least 75mm (3”) left behind the light for lamp servicing and general
ventilation.
After selecting the desired location on a flat surface, cut a 100mm (4”) diameter hole through the vessel hull in the desired location. Caution!
Check that no electrical wiring, fuel lines, oil lines, water lines etc., pass near or through the intended hole location.
The SV10 must be partially disassembled prior to installation. For light disassembly, disconnect Receptacle (12) from Plug (13), unscrew Projector
Lid (11) from Main Body (1), remove Locking Ring (7) and Compression Ring (6) from Main Body (1). Carefully coat Main Body (1), Front Flange
(2) and inner surface of hull hole with 3M 5200 Marine Adhesive or equivalent. Caution! Avoid placing excess adhesive on Main Body (1) threads.
Note: Exposed inner hole surface must be properly sealed before light installation to prevent potential water intrusion into the hull proper. Holding
Front Flange (2), push Main Body (1) through hull hole, slide Compression Ring (6) over Main Body (1) and then tighten Locking Ring (7) hand
tight. Note: Ensure that the tips of all six fasteners (20) are NOT touching Compression Ring (6). After the 3M 5200 Marine Adhesive is fully cured,
tighten the six fasteners (20) to 9 Nm (7 ft/lbs) using a 5mm allen wrench.
Upon making proper electrical connections (see driver box manual), reverse aforementioned light disassembly procedure and hand tighten
Projector Lid (11). Note: Apply anti-seize compound to Projector Lid (11) internal threads. Upon completing light installation, it is highly
recommended that Front Flange (2) be coated with antifouling paint. Also, hand tighten 4mm set screw (22) located in Locking Ring (7), then
connect wire lead from 4mm screw (21) provided on Locking Ring (7) to the vessels bonding system.
Serviceable Parts:
The SV10 LED Underwater Light is fully serviceable and all parts are replaceable. Please contact our technical support staff to discuss your
individual needs.
For Glass Lense (8) replacement disconnect Receptacle (12) from Plug (13), unscrew Projector Lid (11) from Main Body (1), remove Glass
Retaining Ring (3) by removing the six fasteners (20) and remove Glass Gasket (9). Upon thoroughly cleaning all surfaces, reverse said procedure
to reassemble and hand tighten Projector Lid (11). Caution! Never attempt to remove/replace glass lense while vessel is in the water.
MODEL A13A11A25-12G32L
BALLOON
PART
DESCRIPTION
1
10001
MAIN BODY / COFFERDAM
2
10002
FRONT FLANGE
3
10003
GLASS RETAINING RING
4
10219
PROJECTOR MOUNT
5
10220
LENSE HOLDER
6
10006
COMPRESSION RING
7
10007
LOCKING RING
8
10010
GLASS
9
10011
GLASS GASKET
10
10012
CONNECTING RING GASKET
11
10218
PROJECTOR LID
12
10208
RECEPTACLE ASSEMBLY, 2-WAY
13
10209
PLUG ASSEMBLY, 2-WAY
14
10212
LED ARRAY
15
10222
THERMOSWITCH
16
10205
CABLE STRAIN RELIEF
17
10206
ELECTRICAL CABLE
18
10221
LENSE
19
10015
FRONT FLANGE O-RING
20
10020
M6 x 1.0 x 14LG SST SHCS
21
10033
M4 x 0.7 x 6LG SST PPHS
22
10044
M4 x 0.7 x 10LG SST SET SCREW
23
10207
M3 x 0.5 x 5LG SST PPHS
24
10211
M3 x 0.5 x 12LG SST SHCS
25
10223
M4 x 0.7 x 8LG SST PPHS
Underwater Lights USA, LLC
1881 W State Road 84, Bay 102
Fort Lauderdale, FL 33315 USA
Phone: 1-954-760-4447
Fax: 1-954-525-3261
Internet: www.seavision.com
Email: sales@seavision.com
DOC:062212-1
Underwater Lights Europe Sarl
16, rue Rouaze
06400 Cannes, France
Phone: 33-(0)-4-97-21-02-96
Fax: 33-(0)-4-97-21-10-96
Internet: www.seavision.com
Email: sales@seavisioneurope.com
SV18 Driver Box
120-230VAC
Introduction:
Congratulations on the purchase of your new thru hull LED light driver box. Underwater Lights® USA, LLC takes pride in providing
well designed, high quality and thoroughly tested lights that allow you to “enhance your boating experience”. These lights can be
installed in your vessel for aesthetics, to attract fish, for security and safety.
Features Include:
Latest control technology and electronic component construction to guarantee high levels of performance.
Universal VAC input with short circuit, over current, over voltage and over temperature protections.
Electrical wiring terminal block with VAC input fuse protection.
General Safety Information:
This driver box is specifically designed for use with matching Underwater Lights® USA, LLC brand lights only.
Always ensure that VAC power is disconnected and locked out before performing driver box installation and/or service.
The driver box should be opened and visually inspected every six months.
Driver box electrical cabling should be visually inspected for proper operating condition every six months.
Technical Specifications:
Box Dimensions = 260mm (10.2”) long x 160mm (6.3”) wide x 91mm (3.6”) deep - 2.9 kilograms (6.6 pounds)
Box Construction = Gray painted diecast aluminum alloy with polyurethane gasket, IP66/NEMA 4X rated
Driver = 100-277VAC, 50/60 Hz, 1.1-0.45 Ampere input range - Max. 150Watt output - Minimum operating temperature -30°C (-22°F)
Cable to Driver Box = Marine grade electrical cable, 16/3 stranded copper wire, with as short a length as possible
Cable from Driver Box to Light = Marine grade electrical cable, 18/2 stranded copper wire, 5 meters (16 feet) maximum length
Terminal block fuse = Fast blow 10 Amp cylindrical, 6.3mm diameter x 25mm or 32mm long (0.25” diameter x 1.0” or 1.25” long)
Troubleshooting:
Pleased contact our technical support staff in Florida at 1-954-760-4447, Monday to Friday from 8:00 am to 5:00 pm EST.
Warranty:
Underwater Lights® USA, LLC warrants this ballast box to be free from defects in workmanship and materials for a period of two
years from the date of original purchase. Further, misuse, abuse, improper installation, neglect, improper shipping, damage caused
by disasters such as fire, flood and lightning, unauthorized repair or modifications will void said warranty. Should your ballast box
prove defective during the warranty period, promptly contact Underwater Lights® USA, LLC for an RMA number and then return the
ballast box freight prepaid with the RMA number clearly marked on the outside of the shipping container.
Underwater Lights USA, LLC
1881 W State Road 84, Bay 102
Fort Lauderdale, FL 33315 USA
Phone: 1-954-760-4447
Fax: 1-954-525-3261
Internet: www.seavision.com
Email: sales@seavision.com
DOC:092205-4
Underwater Lights Europe Sarl
16 rue Rouaze
06400 Cannes, France
Phone: 33-(0)-4-97-21-02-96
Fax: 33-(0)-4-97-21-10-96
Internet: www.seavision.com
Email: sales@seavisioneurope.com
SV18 Driver Box
120-230VAC
Installation:
The driver box should be mounted in a cool, dry, well ventilated and easily accessible location. Attach the driver box to a fixed
bulkhead or similar secure structure using appropriate M6 fasteners with adequate space between driver boxes for proper cooling.
Note: Whereas the driver box can be placed in any orientation, it is recommended that the cable strain relief connectors face down.
Using marine grade 16/3 cable, run a VAC input line into the driver box and secure by way of one cable strain relief connector.
Run the marine grade 18/2 cable supplied with the thru hull LED light to the driver box and secure by way of one strain relief
connector. Caution! Avoid making tight bends and/or passing cables over sharp edges/surfaces.
Connect cable leads to the driver box fused terminal block as shown in the wiring diagram below.
Serviceable Parts:
Upon opening the driver box by unscrewing four captive lid fasteners, replacement of driver or fused terminal block is accomplished
by removal and replacement of associated fasteners and wiring. Further, a 10 Amp fuse located in the terminal block may be
pulled out and replaced as required. Caution! Ensure that VAC power is disconnected and locked out before servicing driver box.
MODEL 12G32L, 120-230VAC
BALLOON
PART
DESCRIPTION
1
ul-18032
ENCLOSURE
2
ul-18003
TERMINAL BLOCK MOUNT
3
ul-18004
CABLE STRAIN RELIEF
4
ul-18005
BLANKING PLUG
5
ul-18030
DRIVER
6
ul-18008
FUSED TERMINAL BLOCK
7
ul-18013
FAST BLOW FUSE
8
ul-18011
M3.5 x 0.6 x 12LG PPHS
9
ul-18031
M4 x 0.7 x 6LG SST PPHS
Underwater Lights USA, LLC
1881 W State Road 84, Bay 102
Fort Lauderdale, FL 33315 USA
Phone: 1-954-760-4447
Fax: 1-954-525-3261
Internet: www.seavision.com
Email: sales@seavision.com
DOC:092205-4
Underwater Lights Europe Sarl
16 rue Rouaze
06400 Cannes, France
Phone: 33-(0)-4-97-21-02-96
Fax: 33-(0)-4-97-21-10-96
Internet: www.seavision.com
Email: sales@seavisioneurope.com
Download PDF