EASTMAN Fine Grain Release Positive Film 5302 / 7302

EASTMAN Fine Grain Release
Positive Film 5302 / 7302
TECHNICAL DATA / BLACK-AND-WHITE PRINT FILM
EASTMAN Fine Grain Release Positive Film 5302 (35 mm)
and 7302 (16 mm) is a low speed, high-resolution print
film. This blue-sensitive black-and-white film is designed
for general release printing. It is also useful for making
both positive and negative titles, and for dubbing prints for
sound.
PRINTER CONDITIONS
You can make satisfactory prints using negatives of
average density if run on a continuous additive printer
(such as the Bell & Howell Model C) run at 180 ft/min, and
equipped with a 1000-watt lamp operated at 80 volts (85
volts for 35 mm), and a ground glass in the beam. Typical
starting-point printer settings are as follows:
BASE
This film has a clear acetate safety base with an anti-static
protective layer. The base thickness is 5.6 mils. In addition,
7302 Film has an anti-curl layer applied to the base.
DARKROOM RECOMMENDATIONS
Use a KODAK OC Safelight Filter / greenish-yellow, with a
15-watt bulb, no closer to the film than 1.2 metres (4 feet).
STORAGE
Store unexposed film at 13° C (55° F) or lower. For extended
storage, store at -18 C (0° F) or lower. Process exposed film
promptly. Store processed film according to the
recommendations in NAPM IT9.11-1992: for medium-term
storage (minimum of ten years), store at 25° C (77° F) or
lower at a relative humidity of 20 to 50 percent; for
extended-term storage (for preservation of material having
permanent value), store at 21° C (70° F) or lower at a
relative humidity of 20 to 30 percent. For active use, store
at 25° C (77° F) or lower, at a relative humidity of 50 ± 5
percent. This relates to optimized film handling rather than
preservation; static, dust-attraction and curl-related
problems are generally minimized at the higher relative
humidity. After usage, the film should be returned to the
appropriate medium- or long-term storage conditions as
soon as possible.
For more information about medium- and long-term
storage, see NAPM IT9.11-1992, and KODAK Publications
No. H-1, EASTMAN Professional Motion Picture Films and No.
H-23, The Book of Film Care.
©Eastman Kodak Company, 2007
November 2008 • H-1-5302
Beam
Trim Setting
16 mm
35 mm
Tape Setting
16 mm
35 mm
Red
17
21
32
24
Green
17
21
32
24
Blue
17
21
32
24
For laboratories with subtractive printers, such as a Bell
& Howell Model J Printer, the following recommendations
should be helpful as a starting point: 1000-watt lamp at 55
volts and a printer speed of 62 feet per minute for 16 mm
film. For 35 mm film, using a Bell & Howell Model D
Printer: 500-watt lamp at 75 volts and 90 feet per minute.
For both 16 and 35 mm setups use a neutral density filter
(such as the KODAK WRATTEN Neutral Density Filter,
No.96) with a density of 0.50 in the beam and a diaphragm
setting of 13.
SOUND TRACK PRINTING
A variable-area positive silver sound track can be printed
on 5302/7302 Film from a negative sound record on
EASTMAN EXR Sound Recording Film 2378/3378. The
optimum variable-area sound track density for the print
lies between 1.2 and 1.4, measured visually for both 16 and
35 mm films. This print density is chosen to provide a good
compromise between signal-to-noise ratio and frequency
response. The densities of the sound-track negatives
required to produce optimal print densities are determined
by using recognized cross-modulation test procedures.
PROCESSING
IMAGE STRUCTURE
The following process recommendations should be used as
starting points for a typical continuous-immersion
processing machine using formulas presented in KODAK
Publication No.H-24, Manual for Processing EASTMAN
Motion Picture Films, Module 15. The processing times may
require modification for a particular machine.
The modulation-transfer curves, the diffuse rms
granularity, and the resolving-power data were generated
from samples of 5302 Film exposed with tungsten light and
processed as recommended in KODAK Developer D-97 at
70 F (21 C) to the recommended control gamma. For more
information on image-structure characteristics, see
KODAK Publication No H-1, EASTMAN Professional
Motion Picture Films.
Notice: Observe precautionary information on product labels and on the
Material Safety Data Sheets.
Processing Step
Temperature
Time
Replenishment Rate
(mL per 100 ft)
35 mm
70 ± 1/2 ° F
KODAK
Developer D-97* (21 ± 0.3 ° C)
16 mm
†
650
(D-97R)
325
(D-97R)
70 ± 2 F°
(21 ± 1 ° C)
50 sec
12,000
6,000
KODAK Fixing
Bath F-5*
70 ± 2 ° F
(21 ± 1 ° C)
9 min
600
300
Wash (countercurrent)
70 ± 2 ° F
(21 ± 1 ° C)
10 min
12,000
6,000
Stop Rinse
Dry
‡
95° F (35° C)
*
†
Diffuse rms Granularity*
8
Resolving
Power†
63 lines/mm
(TOC 1.6:1)
125 lines/mm
(TOC 1000:1)
Read at a net diffuse visual density of 1.0, using a 48-micrometre aperture.
Determined according to a method similar to the one described in ISO
6328-1982, Photography — Photographic Materials — Determination of ISO
Resolving Power.
CURVES
Characteristic Curves
§
—
Characteristic Curves
4.0
—
Exposure: Tungsten
Process: KODAK Developer
D-97, at 21 C (70 F)
Densitometry: Diffuse
Visual
*
3.0
3.4
TimeGamma
3.2
3.0
9 min.
2.8
2.0
7 min.
5 min.
2.6
GAMMA
DENSITY
Agitation in the developer and fixing bath should be by recirculation through
submerged spray jets that impinge on the film strands.
† Develop to recommended control gamma of 2.4 to 2.6 (Status A).
‡ Countercurrent flow of fixer-laden water overflow from the wash tank, pH
about 6.
§ Many factors affect the drying: air temperature, relative humidity (RH);
volume, rate and distribution of the air flow; final squeegeeing, etc. In a
conventional convection-type drying cabinet with air at about 95° F (35° C)
and 40 to 50 percent RH, drying will take 15 to 20 minutes. With an
impingement-type drying cabinet, however, with a higher temperature and
lower RH, drying time is greatly reduced. With either type of dryer, the film
should be dry without tackiness 1/2 to 2/3 of the way through. Upon cooling
to room temperature after leaving the dryer, the film should be in equilibrium
with the room air at approximately 50 percent RH.
2.4
3 1/2 min.
2.2
NET
FOG
Time-Fog
2.0
2
1.0
4
6
8
DEVELOPMENT TIME
(Minutes)
2 min.
0.10
0.00
10
LUBRICATION
All films destined for projection require some lubrication to
prevent problems during early projection life. Edge waxing
with a paraffin wax solvent solution provides a simple,
inexpensive, and adequate lubrication for 35 and 70 mm
projection prints. For 8 and 16 mm prints, an overall
lubricant may be required.
2
0.0
1.0
0.0
1.0
2.0
LOG EXPOSURE (lux-seconds)
3.0
F010_0023AC
NOTICE: The sensitometric curves and data in this
publication represent product tested under the conditions
of exposure and processing specified. They are
representative of production coatings, and therefore do
not apply directly to a particular box or roll of photographic
material. They do not represent standards or specifications
that must be met by Eastman Kodak Company. The
company reserves the right to change and improve
EASTMAN Fine Grain Release Positive Film 5302 / 7302 • H-1-5302
MORE INFORMATION
Spectral-Sensitivity Curves
p
y
1.0
Effective Exposure:
1.4 seconds
Process: KODAK Developer
D-97 at 21 C(70 F) to
recommended control
gamma
Densitometry: Diffuse Visual
D=0.3 Above
gross fog
LOG SENSITIVITY *
0.0
D=1.0 Above
gross fog
_
Outside the United States and Canada, please contact your
Kodak representative.
You can also visit our web site at www.kodak.com/go/
motion for further information. You may want to
bookmark our location so you can find us easily the next
time.
1.0
Films
Film for the Cinematographer
KODAK Publication No. H-5
_
Image
Structure
KODAK Motion Picture Film
KODAK Publication No. H-1
Storage
KODAK Motion Picture Film
KODAK Publication No. H-1
The Book of Film Care
KODAK Publication No. H-23
Processing
Manual for Processing KODAK Motion Picture Films,
Process ECN-2 Specifications, Module 15
KODAK Publication No. H-24.07
LAD
LAD—Laboratory Aim Density
KODAK Publication No. H-61
Transfer
KODAK Telecine Analysis Film User’s Guide
KODAK Publication No. H-822
KODAK Telecine Exposure Calibration Film User’s
Guide
KODAK Publication No. H-807
2.0
_
3.0
250
300
350
400
450
500
550
600
650
700
750
WAVELENGTH (nm)
*Sensitivity = reciprocal of exposure (ergs/cm 2 ) required
to produce specified density
F010_0024AC
Modulation-Transfer-Function Curve
Modulation Transfer Curve
200
100
70
50
RESPONSE (%)
30
20
10
Effective Exposure:
1.4 seconds
Process: KODAK Developer
D-97 at 21 C(70 F) to
recommended control
gamma
Densitometry: Diffuse Visual
7
5
3
2
1
1
2
3 4 5
10
20
50
100
200
600
SPATIAL FREQUENCY (cycle/mm)
F010_0025AC
These photographic modulation-transfer values were
determined by using a method similar to the one described
in ANSI Standard PH2.39-1977(R1990). The film was
exposed with the specified illuminant to spatially varying
sinusoidal test patterns having an aerial image
modulation of a nominal 35 percent at the image plane,
with processing as indicated. In most cases, the
photographic modulation-transfer values are influenced by
development-adjacency effects and are not equivalent to
the true optical modulation-transfer curve of the emulsion
layer in the particular photographic product
EASTMAN Fine Grain Release Positive Film 5302 / 7302 • H-1-5302
3
EASTMAN Fine Grain Release Positive Film 5302 / 7302
FOR DIRECT ORDERING IN THE UNITED STATES AND CANADA: 1-800-621-FILM
KODAK SHOOTSAVER Film Delivery Service (U.S. only) 1-800-404-2016
Kodak Locations
NORTH AMERICA REGION
UNITED STATES
Hollywood, California
6700 Santa Monica Boulevard
Los Angeles, California
90038-1203
Tel: 323-464-6131
Orders: 1-800-621-FILM
MEXICO
Kodak Mexicana S.A. de C.V.
Blvd. Adolfo Ruiz Cortinez 3642, Piso 14
Col. Jardines del Pedregal
Del. Alvaro Obregon
CP 01900 México, D.F, Mexico.
Tel: 01 (55) 110517-30
Fax: 01 (55) 110517-07
www.kodak.com/go/latinmotion
New York, New York
360 West 31st Street
New York, New York
10001-2727
Tel: 212-631-3400
Orders: 1-800-621-FILM
BRAZIL
KODAK BRASILEIRACOM. PROD.
PARA IMAGEME SERVIÇOS LTDA
CANADA
Kodak Canada Inc.
6 Monogram Place
2nd Floor
Toronto, Ontario
Canada M9R 0A1
Tel: 416-761-4646
Orders: 1-800-621-FILM
Fax: 416-760-4592
Toll Free Fax: 1-866-211-6311
Kodak Canada Inc.
4 Place du Commerce, Suite 100
Ile des Soeurs
Verdun, Quebec
Canada H3E 1J4
Orders: 1-800-621-FILM
Fax: 1-866-211-6311
Kodak Canada Inc.
3700 Gilmore Way
Burnaby, BC
Canada V5G 4M1
Orders: 1-800-621-FILM
Fax: 1-866-211-6311
EUROPEAN, AFRICAN AND
MIDDLE EASTERN REGION
Kodak Business Centre
Hemel One, Boundary Way
Hemel Hempstead
HP2 7YU
England, UK
Tel: + 44 1442 846945
Fax: + 44 1442 846 594
Eastman Kodak SARL
29-31 Route de L'Aeroport
Le Grand Saconnex
Case Postale 271
1215 Geneva 15
Switzerland
Tel: +41-22-747-2000
Fax: +41-22-747-2200
LATIN AMERICA REGION
1900 NW 97 Ave.
Miami, Florida 33172 USA
Tel: 305 378-0566 / 305 229-0422
Fax: 305 378-0495 / 305 229-5075
www.kodak.com/go/latinmotion
EASTMAN Fine Grain Release
Positive Film 5302 / 7302
KODAK Publication No. H-1-5302
CAT 831 2100
Rodovia Presidente Dutra Km154.7
Sao José dos Campos-SP
CEP 12240-427, Brazil
Tel: 0800 015 0002
Tel: 55 11 2132-6003 (Kodak Sao Paulo)
Tel: 55 21 8151-9923 (Kodak Rio de
Janeiro)
Fax 55 12 3932-6721
www.kodak.com/go/latinmotion
VENEZUELA
Kodak Venezuela S. A.
Av. Francisco deMiranda
Centro Lido, Torre B, Piso 7, Of. 71A y
72B
El Rosal, Caracas-Venezuela
Tel: (58-212) 955-2081
Fax: (58-212) 955-2009
www.kodak.com/go/latinmotion
PERU
Kodak Américas, Ltd.
Avenida Larco # 1301, Piso 14,
Miraflores
Lima, Perú
Tel: (51-1) 610-8700
Fax: (51-1) 610-8801
www.kodak.com/go/latinmotion
ARGENTINA
EI Business Center
Bonpland 1930-32
CP 1414 Buenos Aires, Argentina
Tel: 54-11-4778-7009 /
54-911-5932-9503
Fax: 54-11-4773-6105
www.kodak.com/go/latinmotion
CHILE
Kodak Chilena S.A.F.
Edificio Torre Oriente
Av.Alonso de Córdoba# 5151, Piso 14
Comuna Las Condes
Santiago, Chile
Tel: 56.99.220.5609
www.kodak.com/go/latinmotion
ASIA PACIFIC REGION
AUSTRALIA
Melbourne
Kodak (Australasia) Pty. Ltd.
181 Victoria Parade
Collingwood, Victoria, 3066
Australia
Tel: 61 3 8417 8520
Fax: 61 3 8417 8011
E-mail:mpfilmoz@kodak.com
www.kodak.com.au/go/motion
Sydney
Level 4, 68-72 Waterloo Road
North Ryde, NSW2113
Australia
Tel: 61 2 9870 4378
Fax: 61 2 9870 4292
CHINA (Peoples Republic)
Kodak (China) Limited
Beijing Liaison Office
9th Floor, Beijing Kerry Centre
1 Guanghua Road
Chaoyang District
Beijing 100020 China
Tel: 8610 6561 6561
Fax: 8610 6561 2199
Shanghai Liaison Office
Building 8 Jinqiao Office Park
No 27 Xin Qiao Road
Pudong, Shanghai 201206 China
Tel: 8621 5884 1000
Fax: 8621 58841666
Guangzhou Liaison Office
10F, Office Tower
China Hotel by Marriott
Liu Hua Road
GuangZhou 510015
China
Tel: 8620 8666 9888
Fax: 8620 8667 2230
www.kodak.cn/go/motion
HONG KONG
Kodak (Hong Kong) Ltd.
13/F, Cityplaza Four
12 Taikoo Wan Road
Taikoo Shing
Hong Kong
Tel: 852 2564 9352
Fax: 852 2564 9830
www.kodak.com.hk/go/motion
INDIA
Kodak India Private Limited
3rd Floor, Kalpataru Synergy
Off Western Express Highway
Vakola, Santacruz (East)
Mumbai 400 055 India
Tel: 91 22 6641 6762
Fax: 91 22 6641 6769
www.kodak.co.in/go/motion
INDONESIA
PT. Interdelta Tbk (Kodak Motion
Picture Authorized Distributor in
Indonesia)
Tel: 6221 652 333 ext. 250
Mobile: 6281 896 6655
Email:motionpicture@intedelta.co.id
JAPAN
Kodak Japan Ltd.
Tokyo Sumitomo Twin Building (East)
27-1, Shinkawa 2-chome, Chuo-ku
Tokyo 104-0033
Japan
Tel: 813 5540 2280
Fax: 813 5540 2281
e-mail:motionjp@kodak.com
www.kodak.co.jp/go/motion/
KOREA
Kodak Korea Ltd
7th Floor. Yakult Building
28-10, Jamwon-dong, Seocho-gu
Seoul 137-904
Korea
Tel: 822 3438 2620
Fax: 822 3438 2663/2664
wwwkr.kodak.com/go/motion
MALAYSIA
5th Floor, Block A
Peremba Square
Saujana Resort, Sec. U2
40150 Shah Alam
Selangor
Malaysia
Tel: 603 7680 3338
Fax: 603 7680 3333
NEW ZEALAND
Kodak New Zealand Ltd.
Suite 4B
125 The Strand
Parnell 1010
Auckland
New Zealand
Tel: 64 9 3028665
Fax: 649 302 8639
www.kodak.co/nz/go/motion
PAKISTAN
Kodak Ltd Pakistan Branch
5th Floor Bahria Complex 2
M.t.Khan Road
Karachi
Pakistan
Tel: 92 21 561 0150 & 561 1402
Fax: 92 21 561 0776
PHILIPPINES
Kodak Philippines Ltd.
2247 Chino Roces Avenue
Makati City
Philippines 1231
Tel: 632 810 0331 (trunkline) or 632
813 7916 (direct line)
Fax: 632 840 1956
SINGAPORE
Kodak (Singapore) Pte Ltd
151 Lorong Chuan (Lobby A)
#05-01, New Tech Park
Singapore 556741
Tel: 65 6371 3388
Fax: 65 6371 3377
TAIWAN
Kodak Taiwan Limited
Shin Kong Life Neihu Technology
Building
3F-1, No.301, Sec. 2, Tiding Blvd.
Neihu District
Taipei 11493
Taiwan, R.O.C.
Tel: 886 2 8751 8282
www.kodak.com.tw/go/motion
THAILAND
Kodak (Thailand) Ltd.
Floors 6 - 8th Kasemsap Bldg.
89/1 Moo 14, Vibhavadee-rangsit Rd.
Chatuchak
Bangkok 10900
Thailand
Tel: 66 2 515 8092
Kodak, Eastman, 5302, 7302, 2378, 3378, Vision, and Wratten are trademarks.
Revised 11-08
Printed in U.S.A.
Download PDF