Network Camera V4.1.0 ES-HNG200I-EI

Add to my manuals
16 Pages

advertisement

Network Camera V4.1.0 ES-HNG200I-EI | Manualzz

Network Camera V4.1.0

ES-HNG200I-EI

Installer/User Guide

CONTENTS

1.0 Physical Description of Camera ....................................................................1

1.1 Camera Description ......................................................................................................................1

1.2 Camera Wiring Diagram .........................................................................................................2

2.0 Installation .......................................................................................................... 2

3.0 Setting the Network Camera over the LAN ............................................... 7

3.1 Modify device info ........................................................................................................................8

4.0 Accessing via Web Browser ........................................................................ 10

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

Save these instructions

This manual contains important instructions that should be followed during installation and maintenance of the Network Bullet

Camera V4.1.0 ES-HNG200I-EI.

Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer.

ABOUT THIS DOCUMENT

This manual applies to ES-HND200I-EI series cameras. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.

DISCLAIMER STATEMENT

“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL

Certification does not cover the performance or reliability of the security or signaling aspects of this product. UL MAKES NO

REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY

OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.

0400031020820

1.0 PHYSICAL DESCRIPTION OF CAMERA

1.1 Camera Description

NOTE: Two types of interfaces of cameras as shown in Figure 1-1 and Figure 1-2. Please choose the right figure according to the appearance of your camera.

Figure 1-1 Overview

Figure 1-2 Overview

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

1

1.2 Camera Wiring Diagram

3

4

NO.

1

2

5

DESCRIPTION

10M/100M self-adaptive Ethernet interface

Power supply interface

IN, G: Alarm input interface

1A, 1B: Alarm output interface

D+, D-: RS-485 interface

AUDIO IN, G: Audio input interface

AUDIO OUT, G: Audio output interface

Figure 1-3 Wiring Diagram

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

2

2.0 INSTALLATION

NOTES:

Read the following contents carefully before the installation.

Make sure that all the related equipment is power-off during the installation.

Check whether the power supply is matched with your AC outlet to avoid damage.

Do not place the camera in extremely hot or damp environment. To avoid heat accumulation, good ventilation is required for a proper operating environment. You may refer to the specification of the product for the detailed information about installation environment.

If the product does not function properly, please contact your dealer or the nearest service center.

Do not disassemble the camera for repair or maintenance by yourself.

The bullet camera can be installed to both wall and ceiling. This quick guide takes wall mounting steps as an example.

Steps:

1. Use the screws to fix the mounting base to the ceiling; rotate the back box counterclockwise to secure it to

the mounting base; use the lock screw to secure the dome camera.

Lock screw

Figure 2-1 Fix the Mounting Base

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

3

NOTES:

Please apply water-proof measures between the ceiling surface and mounting base and around the

cables.

For cement wall mounting, you need to use the expansion screw to fix the mounting base. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the mounting

base.

For wooden wall mounting, you can just use the self-tapping screw to fix the mounting base.

The wall must be strong enough to withstand more than 3 times of the weight of the camera and the

bracket.

2. Fix the mounting bracket with the camera to the mounting base.

NOTE: The “bottom” mark on the mounting base should align with the “bottom” mark on the

mounting bracket.

Figure 2-2 Fix the Camera

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

4

3.) View the image of the camera over the network.

4. Loosen the screws on the bracket slightly.

NOTE: The “bottom” mark on the mounting base should align with the “bottom” mark on the

mounting bracket.

5. Adjust the camera to the desired surveillance angle and then tighten the screws on bracket to fix the camera.

Rotation screw

Panning screw

Tilting screw

Figure 2-3 Adjust Monitoring Angle

6. Loosen the lock screw on the sun shield and move the sun shield until you can remove it. Remove the sun

shield.

Figure 2-4 Remove the Sun Shield

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

5

7. Rotate to remove the front cover from camera and adjust the lens to get a clear image.

Adjust the lens

Front cover

Figure 2-5 Adjust the Lens

8. Fix the lens; reinstall the front cover and the sun shield to finish the installation.

NOTE: Reinstall the front cover until aligning the mark on the front cover with the mark on the

camera.

Figure 2-6 Reinstall the Camera

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

6

3.0 SETTING THE NETWORK CAMERA OVER THE LAN

Purpose:

To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or iVMS-4200 software to search and change the IP of network camera.

The following figure shows the cable connection of network camera and PC:

Figure 3-1 Wiring over LAN

Set the IP address of the camera for accessing via LAN.

Steps:

1. To get the IP address, you can choose either of the following methods: y Use SADP, a software tool which can automatically detect network camera in the LAN and list the device

information like IP address, subnet mask, port number, device serial number, device version, etc., shown in

Figure 3-2.

y Use iVMS-4200 software and to list the online devices. Please refer to the user manual of client software for

detailed information.

2. Change the IP address and subnet mask to the same subnet as of your PC.

Refer to the following introductions to set IP address with SADP software: y Search active devices online

Search online devices automatically:

After launch the SADP software, it automatically searches the online devices every 15 seconds from the subnet where your computer locates. It displays the total number and information of the searched devices in the Online Devices interface. Device information including the device type, IP address, port number, gateway, etc. will be displayed.

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

7

Figure 3-2 Searching Online Devices

Note: Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline.

Search online devices manually:

You can will be added to the list.

also click to refresh the online device list manually. The newly searched devices

Note: You can you can click click or on each column heading to order the information; to show the device table and hide the network parameter panel on the right side, or click to show the network parameter panel.

3.1 Modify device Information:

Steps:

1.) Left click to select a device to be modified in the device list as shown in Figure 3-3. The network parameters of the device will be displayed in the Modify Network Parameters panel on the right side as shown in Figure 3-4.

2.) Edit the modifiable network parameters, e.g. IP address and port number.

Enter the password of the admin account of the device in the Password field and click changes.

to save the

Figure 3-3 Select a device

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

8

Figure 3-4 Modify Network Parameters

3. Enter the IP address of network camera in the address field of the web browser to get the liveview.

Notes:

• The default IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”.Use iVMS-4200 software and to list the online devices. Please refer to the user manual of client software for detailed information.

• For accessing the network camera from different subnets, please set the gateway for the network camera after you log in.

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

9

4.0 ACCESSING VIA WEB BROWSER

System Requirements:

Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits.

CPU: Intel Pentium IV 3.0 GHz or higher.

RAM: 1G or higher.

Display: 1024×768 resolution or higher.

Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome 8 and above version.

Steps:

1. Open the web browser.

2. In the browser address bar, input the IP address of the network camera, e.g., 192.0.0.64 and press the Enter key to enter the login interface.

3. Input the user name and password.

4. Click

Figure 4-1 Login Interface

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

10

5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to

install the plug-in.

Figure 4-2 Download Plug-in

Figure 4-3 Download Plug-in

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

11

Figure 4-4 Install Plug-in

Figure 4-5 Install Plug-in

6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login.

NOTE: For detailed instructions of further configuration, please refer to the user manual of

Vertiv | Network Camera Quick Operation Guide | v01 | UD.6L0201D0146A02

12

VertivCo.com

© 2017 Vertiv Co. All rights reserved. Vertiv, the Vertiv logo are trademarks or registered trademarks of Vertiv Co. All other names and logos referred to are trade names, trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.

UD.6L0201D0140A02

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals