Quick Start Guide - i3 International

Quick Start Guide
SP12 PoE Splitter
DIMENSIONS AND PORTS
PACKAGE CONTENTS
9V
12V
5V
Voltage Selector
Switch
DC Power
Out
7.5V
Data Power In Port
Width
78 mm
(31/16”)
Height
27mm
(11/16”)
Ensure that the items received match those listed on
the order form and the packing slip.
In addition to this manual the packing box includes:
1. One palm-sized SP12 PoE Splitter.
2. Two Power cables. One Red 5.5x2.5mm and one
Black 5.5x2.1mm
INSTALLATION INSTRUCTIONS
Length
72 mm
(23/4”)
IMPORTANT
1. Install SP12 PoE Splitter for surface mounting as
required.
2. Four mounting screws (not included) can be used to
secure the splitter to a surface close enough to the
target device for the power cables to reach.
3. Insert the PoE Ethernet cable coming from the PoE
Switch or power injector hub into the Data Power In
Port.
4. Connect a CAT5/6 (not included) Ethernet cable into
the RJ45 Data Out Port on the splitter and connect it
into the data port on the target device.
5. Determine which power cable fits the target device.
The red cable has a 2.5mm connector and the black
has a 2.1mm connector. Connect the 5.5mm end of
the cord to the DC Power Out port on the splitter
and the other end of the cord into the power input of
the target device.
6. Ensure that the setting on the voltage selection
switch on the splitter is set to the power
requirements of the target device (12V, 9V, 7.5V, or
5V).
7. The LED indicators will glow Yellow to indicate the
splitter is powered on and functioning.
• It is the installer’s
responsibility to ensure
that the mounting surface
is suitable for the chosen
installation method.
• Based on installation
location and surface
type, supplied mounting
hardware may be
inadequate.
• Mounting hardware is
site-specific and will need
to be supplied by the
installer.
CAUTION
• Ensure the voltage
selection switch on the
side of the splitter is set
to the appropriate level
for the target device.
Improper voltage can
result in damage to the
non PoE device being
powered by the splitter.
i3-TRNG-CAMS-SP12.indd
The SP12 PoE Splitter receives power and data from the power over Ethernet network and
separates the data from the power to provide both the data and 12V , 9V, 7.5V, or 5V direct
power to a non PoE enabled device.
• Four built-in mounting brackets for surface mounting (mounting screws not included)
• One RJ45 PoE in port
• One RJ45 Ethernet Data Out Port
• One DC Power Out Port
• One Voltage setting switch. 12V, 9V, 7.5V, and 5V
Data Out Port
LED Indicators
KEY FEATURES
•
•
•
•
•
•
•
•
•
Complies with IEEE802.3 10Base-T; IEEE802.3u,
100Base-TX; IEEE802.3ab, and 1000Base-T.
Complies with IEEE802.3at PoE standards.
Supports two 10/100/1000M auto-detect Half/Full-Duplex
switch ports with TX interfaces.
Two RJ45 Port Interfaces, one Data+Power Input port; one
Data Output port and one Power Output port.
Auto Detects PoE equipment, IEEE802.3at, protecting the
device from being damaged by incorrect links.
Supplies a power source of 5V / 7.5V / 9V / 12V up to 2A
peak.
LED indicators for Power function display.
Ethernet Data Transfer rates: 10Mbps/Half-Duplex, 20Mbps/
Full-Duplex .
Fast Ethernet Data Transfer Rates: 100Mbps / Half-Duplex,
200Mbps / Full-Duplex, Giga 2000Mpbs / Full-Duplex.
i3 INTERNATIONAL INC.
1.866.840.0004
www.i3international.com
U.S.A
4450 Witmer Industrial Estates Unit 4
Niagara Falls, NY 14305
Canada 780 Birchmount Road, Unit 16,
Scarborough, ON, M1K 5H4 Rev. 160317
Download PDF