TE 500 / TE 500-AVR

TE 500 /
TE 500-AVR
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
Operating instructions
en
Mode d’emploi
fr
Manual de instrucciones
es
Manual de instruções
pt
1
1
2
9
6
4
3
5
8
7
This Product is Certified
Ce produit est homologué
Producto homologado por
Este produto está registrado
C
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
US
2
3
6
4
5
4
1
1
2
3
3
2/5
4
5
1
3
1
2
07
a.m
7:30
2
6
3/5
1
4
2
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
ORIGINAL OPERATING INSTRUCTIONS
TE 500 / TE 500‑AVR breaker
It is essential that the operating instructions
are read before the power tool is operated for
the first time.
Always keep these operating instructions together with the power tool.
Ensure that the operating instructions are
with the power tool when it is given to other
persons.
Contents
1 General information
2 Description
3 Accessories, consumables
4 Technical data
5 Safety instructions
6 Before use
7 Operation
8 Care and maintenance
9 Troubleshooting
10 Disposal
11 Manufacturer’s warranty - tools
Page
1
2
4
4
5
7
7
9
9
10
10
1 These numbers refer to the corresponding illustrations. The illustrations can be found on the fold-out cover
pages. Keep these pages open while studying the operating instructions.
In these operating instructions, the designation “the
power tool” always refers to the TE 500 or TE 500-AVR
breaker.
Operating controls and indicators 1
@ Chuck
; Function selector switch
= Control switch
% Control switch lock
& Side handle
( Rear grip surface
) Service indicator
+ Theft protection indicator (optional)
§ AVR active vibration reduction (only TE 500‑AVR)
1 General information
1.1 Safety notices and their meaning
DANGER
Draws attention to imminent danger that will lead to
serious bodily injury or fatality.
WARNING
Draws attention to a potentially dangerous situation that
could lead to serious personal injury or fatality.
CAUTION
Draws attention to a potentially dangerous situation that
could lead to slight personal injury or damage to the
equipment or other property.
1.2 Explanation of the pictograms and other
information
Warning signs
General
warning
Warning:
electricity
Warning: hot
surface
NOTE
Draws attention to an instruction or other useful information.
1
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
en
Obligation signs
Wear eye
protection
en
Wear a hard
hat
Wear ear
protection
Wear
protective
gloves
Location of identification data on the power tool
The type designation can be found on the type identification plate and the serial number on the side of the motor
housing. Make a note of this data in your operating instructions and always refer to it when making an enquiry
to your Hilti representative or service department.
Type:
Serial no.:
Wear
breathing
protection
Symbols
Read the
operating
instructions
before use
Return waste
material for
recycling.
Chiseling
Chisel
position
adjustment
Volts
Amps
Alternating
current
Hertz
Double
insulated
Lock symbol
Equipped
with theft
protection
system
2 Description
2.1 Use of the product as directed
The power tool is an electrically-powered breaker with pneumatic hammering mechanism.
The power tool is designed for medium-duty chiseling on masonry and concrete.
Working on materials hazardous to the health (e.g. asbestos) is not permissible.
The power tool is designed for professional use and may be operated, serviced and maintained only by trained,
authorized personnel. This personnel must be informed of any special hazards that may be encountered. The power
tool and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not
as directed.
The working environment may be as follows: construction site, workshop, renovation, conversion or new construction.
The power tool may be used only in a dry environment.
Do not use the power tool where there is a risk of fire or explosion.
The power tool may be operated only when connected to a power supply providing a voltage and frequency in
compliance with the information given on its type identification plate.
Modification of the power tool or tampering with its parts is not permissible.
To avoid the risk of injury, use only genuine Hilti accessories and insert tools.
2
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
Observe the information printed in the operating instructions concerning operation, care and maintenance.
2.2 Chuck
TE‑Y (SDS‑max) chuck
en
2.3 Switches
Lockable control switch
Function selector switch:
Chisel adjustment (24 positions)
Chiseling
2.4 Grips
Vibration-absorbing, pivotable side handle
Vibration-absorbing grip
2.5 Protective devices
Electronic restart interlock to prevent the power tool starting unintentionally after an interruption in the electric supply
(see section 9 “Troubleshooting”).
2.6 Lubrication
Gearing and hammering mechanism with separate lubrication chambers
2.7 Active vibration reduction (only TE 500‑AVR)
The power tool is equipped with an AVR active vibration reduction system which reduces vibration significantly
compared to power tools without active vibration reduction.
2.8 TPS theft protection system (optional)
The power tool may be equipped with the TPS theft protection system as an option. If the power tool is equipped with
this feature, it can be unlocked and made ready for operation only through use of the corresponding TPS key.
2.9 LED indicators
Service indicator LED (see section “Care and maintenance”)
Theft protection system indicator (optional) (see section “Operation”)
2.10 Items supplied as standard
1
Power tool with side handle
1
Hilti toolbox
1
1
1
Operating instructions
Cleaning cloth
Grease
2.11 Using extension cords
Use only extension cords of a type approved for the application and with conductors of adequate cross section.
The power tool may otherwise lose performance and the extension cord may overheat. Check the extension cord for
damage at regular intervals. Replace damaged extension cords.
Recommended minimum conductor cross section and max. cable lengths
Conductor cross section
14 AWG
12 AWG
Mains voltage 110-120 V
75 m (246.06 ft)
125 m (410.1 ft)
Do not use extension cords with 16 AWG conductor cross section.
3
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
2.12 Using extension cords outdoors
When working outdoors, use only extension cords that are approved and correspondingly marked for this application.
2.13 Using a generator or transformer
en
This power tool may be powered by a generator or transformer when the following conditions are fulfilled: The unit
must provide a power output in watts of at least twice the value printed on the type identification plate on the power
tool. The operating voltage must remain within +5% and -15% of the rated voltage at all times, frequency must be in
the 50 – 60 Hz range and never above 65 Hz, and the unit must be equipped with automatic voltage regulation and
starting boost.
Never operate other power tools or appliances from the generator or transformer at the same time. Switching other
power tools or appliances on and off may cause undervoltage and / or overvoltage peaks, resulting in damage to the
power tool.
3 Accessories, consumables
Designation
Item number, description
TPS Theft Protection System with Company Card,
Company Remote and TPS‑K key
206999, optional
Use the Hilti insert tools listed below. With these insert tools you will achieve higher performance and longer
tool life as the power tool and insert tools have been optimized as a system.
TE‑Y (SDS‑max) chuck
Width (mm)
Pointed chisels
Length (mm)
Width (in)
280…700
Length (in)
11…27"
Flat chisels
26
280…700
³⁄₄"
Wide-flat chisels
50…120
280…500
2…4¹⁄₂"
11…27"
11…19"
Hollow chisel
28
280
1"
11"
Channel chisel
22…36
280
⁷⁄₈…1¹⁄₂"
11"
Mortar chisel
38
280
¹⁵⁄₁₆"
11"
Flexible chisel
150
650
5⁷⁄₈"
25¹⁄₂"
Bushing tool
40X40
250
5⁷⁄₈"
10"
Tamping tool
150X150
300
Earth rod rammer
∅ 15…25
300
4 Technical data
Right of technical changes reserved.
Power tool
TE 500
Rated voltage
120 V
Rated current input
13.1 A
Mains frequency
60 Hz
Weight of the TE 500
5.6 kg (12.35 lb)
Weight of the TE 500‑AVR
5.7 kg (12.57 lb)
Dimensions (L x W x H)
471 mm (18.54") x 108 mm (4.25") x 243 mm (9.57")
Single impact energy
7.5 J
4
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
Other information about the power tool
Chuck
Protection class
TE‑Y (SDS‑max)
Protection class I (grounded) or protection class II (double insulated). See type identification plate.
en
5 Safety instructions
5.1 General Power Tool Safety Warnings
a)
WARNING
Read all safety warnings and instructions. Failure
to follow the warnings and instructions may result
in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference.
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or batteryoperated (cordless) power tool.
5.1.1 Work area safety
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
a)
5.1.2 Electrical safety
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk
of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
a)
5.1.3 Personal safety
a)
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off‐position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
5.1.4 Power tool use and care
Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
a)
5
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
en
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions taking into
account the working conditions and the work to
be performed. Use of the power tool for operations different from those intended could result in a
hazardous situation.
5.1.5 Service
a)
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
5.2 Hammer safety warnings
Wear ear protectors. Exposure to noise can cause
hearing loss.
b) Use auxiliary handles, if supplied with the tool.
Loss of control can cause personal injury.
c) Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
a)
5.3 Additional safety precautions
5.3.1 Personal safety
Keep the grips dry, clean and free from oil and
grease.
b) Wear a dust mask.
c) Improve the blood circulation in your fingers by
relaxing your hands and exercising your fingers
during breaks between working.
d) Always lead the supply cord and extension cord
away from the power tool to the rear while working. This helps to avoid tripping over the cord while
working.
e) Children must be instructed not to play with the
power tool.
f) The power tool is not intended for use by children,
by debilitated persons or those who have received
no instruction or training.
a)
5.3.2 Power tool use and care
Secure the workpiece. Use clamps or a vice to
secure the workpiece. The workpiece is thus held
more securely than by hand and both hands remain
free to operate the power tool.
b) Check that the insert tools used are compatible
with the chuck system and that they are secured
in the chuck correctly.
c) Always work from a secure, safe stance.
a)
6
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
5.3.3 Electrical safety
Before beginning work, check the working area
(e.g. using a metal detector) to ensure that no
concealed electric cables or gas and water pipes
are present. External metal parts of the power tool
may become live, for example, when an electric cable
is damaged accidentally. This presents a serious risk
of electric shock.
b) Check the power tool’s supply cord at regular
intervals and have it replaced by a qualified specialist if found to be damaged. If the power tool’s
supply cord is damaged it must be replaced with
a specially-prepared supply cord available from
Hilti Customer Service. Check extension cords
at regular intervals and replace them if found to
be damaged. Do not touch the supply cord or
extension cord if it is damaged while working.
Disconnect the supply cord plug from the power
outlet. Damaged supply cords or extension cords
present a risk of electric shock.
c) Dirty or dusty power tools which have been used
frequently for work on conductive materials
should be checked at regular intervals at a Hilti
Service Center. Under unfavorable circumstances,
dampness or dust adhering to the surface of
the power tool, especially dust from conductive
materials, may present a risk of electric shock.
d) When working outdoors with an electric tool
check to ensure that the tool is connected to the
electric supply by way of a ground fault circuit
interrupter (GFCI) with a rating of max. 30 mA
(tripping current). Use of a ground fault circuit
interrupter reduces the risk of electric shock.
e) Use of a ground fault circuit interrupter (GFCI)
with a maximum tripping current of 30 mA is
recommended.
a)
5.3.4 Work area safety
a) Ensure that the workplace is well lit.
b) Ensure that the workplace is well ventilated. Exposure to dust at a poorly ventilated workplace may
result in damage to the health.
c) WARNING: Some dust created by grinding, sanding, cutting and drilling contains chemicals known
to cause cancer, birth defects, infertility or other
reproductive harm; or serious and permanent respiratory or other injury. Some examples of these
chemicals are: lead from lead-based paints, crystalline silica from bricks, concrete and other masonry
products and natural stone, arsenic and chromium
from chemically-treated lumber. Your risk from these
exposures varies, depending on how often you do
this type of work. To reduce exposure to these
chemicals, the operator and bystanders should
work in a well-ventilated area, work with approved safety equipment, such as respiratory pro-
tection appropriate for the type of dust generated,
and designed to filter out microscopic particles
and direct dust away from the face and body.
Avoid prolonged contact with dust. Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth,
eyes, or to remain on your skin may promote absorption of harmful chemicals.
d) If the work involves breaking right through, take
the appropriate safety measures at the opposite
side. Parts breaking away could fall out and / or fall
down and injure other persons.
5.3.5 Personal protective equipment
en
The user and any other persons in the vicinity must
wear ANSI Z87.1-approved eye protection, a hard
hat, ear protection, protective gloves and breathing
protection while the machine is in use.
6 Before use
2.
3.
CAUTION
Check the insert tool for damage or uneven wear each
time before use.
6.1 Fitting and adjusting the side handle 2
1.
Disconnect the supply cord plug from the power
outlet.
4.
5.
Release the side handle clamping band by turning
the knob.
Slide the side handle clamping band over the chuck
and onto the cylindrical section at the front end of
the power tool.
Pivot the side handle into the desired position.
Secure the side handle by turning the knob.
6.2 Unlocking the tool (theft protection system)
NOTE
See section “Using the TPS theft protection system”.
6.3 Use of extension cords and generators or
transformers
Please refer to section 2 “Description”.
7 Operation
2.
3.
DANGER
Always hold the power tool securely with both hands
on the grips provided. Keep the grips dry, clean and
free from oil and grease.
7.1 Preparing for use
CAUTION
Wear protective gloves when changing insert tools
as the insert tools get hot through use and they may
have sharp edges.
7.1.1 Fitting the insert tool 3
1.
Disconnect the supply cord plug from the power
outlet.
4.
5.
6.
Check that the connection end of the insert tool is
clean and lightly greased. Clean it and grease it if
necessary.
Check that the sealing lip of the dust shield is
clean and in good condition. Clean the dust shield
if necessary or have it replaced if the sealing lip is
damaged.
Push the insert tool into the chuck and rotate it while
applying slight pressure until it engages in the guide
grooves.
Push the insert tool further into the chuck until it is
heard to engage.
Check that the insert tool has engaged correctly by
pulling it.
7.1.2 Removing the insert tool 4
1.
Disconnect the supply cord plug from the power
outlet.
7
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
2.
3.
Open the chuck by pulling back the insert tool locking sleeve.
Pull the insert tool out of the chuck.
7.2 Operation
en
7.2.2 Chiseling
NOTE
Working at low temperatures: The hammering mechanism works only when the power tool has reached a
minimum operating temperature. Bring the chisel into
contact with the base material and allow the power tool
to run under no load until the minimum operating temperature is reached. If necessary, repeat this procedure
until the hammering mechanism begins to operate.
CAUTION
Working on the material may cause it to splinter. Wear
eye protection and protective gloves. Wear breathing
protection if no dust removal system is used. Splintering material presents a risk of injury to the eyes and
body.
NOTE
The chisel can be adjusted to 24 different positions
(in 15° increments). This ensures that flat chisels and
shaped chisels can always be set to the optimum working
position.
CAUTION
The work generates noise. Wear ear protectors. Exposure to noise can cause hearing loss.
CAUTION
Do not operate the power tool when the selector switch
is set to “Chisel adjustment”.
7.2.1 TPS theft protection system (optional)
NOTE
The power tool may be equipped with the optional theft
protection system. If the power tool is equipped with this
feature, it can be unlocked and made ready for operation
only through use of the corresponding TPS key.
7.2.1.1 Unlocking the power tool 5
1.
2.
Plug the supply cord into the power outlet. The
yellow theft protection indicator LED blinks. The
power tool is now ready to receive the signal from
the TPS key.
Hold the TPS key or the TPS watch strap buckle
against the lock symbol. The power tool is unlocked
as soon as the yellow theft protection indicator LED
no longer lights.
NOTE If, for example, the electric supply is briefly
interrupted due to a power failure or disconnected
when moving to a different workplace, the power
tool remains ready for operation for approx. 20 minutes. In the event of a longer interruption, the TPS
key must be used again to unlock the power tool.
7.2.1.2 Activation of the theft protection system for
the power tool
NOTE
Further detailed information on activation and use of the
theft protection system can be found in the operating
instructions for the theft protection system.
8
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
7.2.2.1 Chisel position adjustment 6
1.
2.
3.
4.
5.
Disconnect the supply cord plug from the power
outlet.
Turn the function selector switch until it engages in
the “Chisel adjustment” position.
Rotate the chisel to the desired position.
Turn the function selector switch to the “chiseling”
position.
Rotate the chisel until it engages. Do not operate the
function selector switch while the motor is running.
7.2.3 Locking the control switch
When chiseling, the control switch can be locked in the
“on” position.
7.2.3.1 Locking the control switch
1.
2.
Press the control switch fully.
Press the control switch lock fully. The lock is positioned on the inside of the upper control switch.
NOTE The power tool then operates in sustained
mode.
7.2.3.2 Resetting the control switch
Press the control switch fully and then release it.
The power tool then switches off.
8 Care and maintenance
CAUTION
Disconnect the mains plug from the power outlet.
8.1 Care of insert tools
Clean off dirt and dust deposits adhering to the insert
tools and protect them from corrosion by wiping the
insert tools from time to time with an oil-soaked rag.
8.2 Care of the power tool
CAUTION
Keep the power tool, especially its grip surfaces,
clean and free from oil and grease. Do not use cleaning agents which contain silicone.
The outer casing of the power tool is made from impactresistant plastic. Sections of the grip are made from a
synthetic rubber material.
Never operate the power tool when the ventilation slots
are blocked. Clean the ventilation slots carefully using
a dry brush. Do not permit foreign objects to enter the
interior of the power tool. Clean the outside of the power
tool at regular intervals with a slightly damp cloth. Do
not use a spray, steam pressure cleaning equipment or
running water for cleaning. This may negatively affect the
electrical safety of the power tool.
8.3 Service indicator
NOTE
The power tool is equipped with a service indicator.
Indicator
Constant red light
End of service interval - servicing is due.
After the lamp lights for the first time,
the power tool may continue to be used
for several hours before the automatic
cut-out is activated. To ensure that the
power tool is always ready for use, it
should be returned to Hilti for servicing
in good time.
See section “Troubleshooting”.
Blinking red light
8.4 Maintenance
WARNING
Repairs to the electrical section of the power tool may
be carried out only by trained electrical specialists.
Check all external parts of the power tool for damage
at regular intervals and check that all controls operate
faultlessly. Do not operate the power tool if parts are
damaged or when the controls do not function faultlessly.
If necessary, the power tool should be repaired by Hilti
Service.
8.5 Checking the power tool after care and
maintenance
After carrying out care and maintenance work on the
power tool, check that all protective and safety devices
are fitted and that they function faultlessly.
9 Troubleshooting
Fault
Possible cause
Remedy
The power tool doesn’t start.
Interruption in the electric supply.
Plug in another electric appliance and
check whether it works.
Have it checked by a trained electrical
specialist and replaced if necessary.
Apply a load to the generator by connecting another appliance (e.g. a
lamp). Subsequently switch the power
tool off and on again.
Have it checked by a trained electrical
specialist.
Switch the power tool off and on
again.
The supply cord or plug is defective.
Generator with sleep mode.
Other electrical fault.
The electronic restart interlock is activated after an interruption in the electric supply.
9
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
en
en
Fault
Possible cause
Remedy
No hammering action.
The power tool is too cold.
Allow the power tool to warm up to
the minimum operating temperature.
See section: 7.2.2 Chiseling
If necessary, the power tool should be
repaired by Hilti Service.
If necessary, the power tool should be
repaired by Hilti Service.
Have it checked by a trained electrical
specialist and replaced if necessary.
Use the TPS key to unlock the power
tool.
A fault has occurred in the power tool.
The power tool doesn’t start
and the LED blinks red.
The power tool doesn’t start
and the LED lights red.
The power tool doesn’t start
and the indicator lamp blinks
yellow.
The power tool doesn’t achieve
full power.
The chisel can’t be released
from the chuck.
A fault has occurred in the power tool.
The carbon brushes are worn.
The power tool has not been unlocked (power tools with optional theft
protection system).
The extension cord’s conductor cross
section is inadequate.
The control switch is not pressed
fully.
The chuck is not pulled back fully.
Use an extension cord with an adequate conductor cross section.
(Please refer to “Before use”.)
Press the control switch as far as it
will go.
Pull the chuck back as far as it will go
and remove the insert tool.
10 Disposal
Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials
must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for
taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or
Hilti representative for further information.
11 Manufacturer’s warranty - tools
Hilti warrants that the tool supplied is free of defects in
material and workmanship. This warranty is valid so long
as the tool is operated and handled correctly, cleaned
and serviced properly and in accordance with the Hilti
Operating Instructions, and the technical system is maintained. This means that only original Hilti consumables,
components and spare parts may be used in the tool.
This warranty provides the free-of-charge repair or replacement of defective parts only over the entire lifespan
of the tool. Parts requiring repair or replacement as a
result of normal wear and tear are not covered by this
warranty.
10
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
Additional claims are excluded, unless stringent national rules prohibit such exclusion. In particular, Hilti
is not obligated for direct, indirect, incidental or consequential damages, losses or expenses in connection with, or by reason of, the use of, or inability to
use the tool for any purpose. Implied warranties of
merchantability or fitness for a particular purpose are
specifically excluded.
For repair or replacement, send the tool or related parts
immediately upon discovery of the defect to the address
of the local Hilti marketing organization provided.
This constitutes Hilti’s entire obligation with regard to
warranty and supersedes all prior or contemporaneous
comments and oral or written agreements concerning
warranties.
Hilti Corporation
Printed: 08.07.2013 | Doc-Nr: PUB / 5130650 / 000 / 01
378617 / A4
378617
Hilti = registered trademark of Hilti Corp., Schaan
W 3256 | 0613 | 00-Pos. 3 | 1
Printed in Germany © 2013
Right of technical and programme changes reserved S. E. & O.
*378617*
LI-9494 Schaan
Tel.: +423 / 234 21 11
Fax:+423 / 234 29 65
www.hilti.com
Download PDF