Security precautions Overview of headset Earpiece Microphone Vol

Security precautions Security precautions: In order to have a proper and safety use of the headset, please read this user manual in detail and save it.  Be sure to aware the following guidelines when using your headset. 1. Should adjust volume and time reasonably when using the headset. 2. Please stop using the headset in potentially hazardous situation to ensure your safety. 3. Please avoid suing headset to listen to music, make or receive calls to avoid distraction while driving. 4. Put this product and its accessories somewhere out of the reach of children, to avoid a fatal danger caused by inappropriate use. 5. Should keep water from entering the headset during grooming, which may cause damage to sound quality or headset. 6. Should avoid turning the volume so high that you can’t hear anything around you. If you feel a tinnitus or the volume is too high, please reduce the volume. 7. Stop using the headset if you feel obvious discomfort, irritation or have other adverse reactions. 8. The headset should not be stored or use at temperatures below ‐15℃(5℉)or above 55℃
(131℉)which may shorten headset or battery life. Overview of headset  Overview of I5 Bluetooth stereo headset : Earpiece Microphone Vol (+) Next Track MF button Vol (‐)/ Previous Track LED Indicator  S2 Bluetooth sports headset in the box : S2 Bluetooth sports headset 1pc USB charging cable 1pc User’s manual 1pc  Charger and battery: Please check the charging cable is original or not before charging the Bluetooth headset. Warning: Must use original charge cable to charge for the Bluetooth headset, otherwise it may damage the headset. Thus, voltage o f charger must be 5V, electric current exceed 100mA (5V / 100mA). Hands Free Charging: This headset uses a non‐detachable built‐in rechargeable battery. In order to prevent damage of the headset, please do not remove the battery. 1. Before charging, make sure the headset has been switched off. 2. Plug USB cable into the charging port of headset; plug the other side of USB cable into USB charger or other charging device. Charging will start and the red light remains bright on the headset. 3. Charging time of headset takes approximately up to 1.5 – 2 hours, blue light remains bright or red light switch off after charging completed.  Pairing mode: Keep press the MF button until blue and red lights blink alternatively.  Reconnection mode: Keep press the MF button until blue light blinks.  Switch off Keep press the MF button until red light blinks.  Pair your headset with your mobile phone: 1. Keep the distance between the headset and mobile phone within 1 meter. The closer, the better. 2. Keep press the MF button until blue and red lights blink alternatively. , entered to pairing mode. 3. Initiate Bluetooth function of mobile phone (or other device needed to be connected). Then “ S2 ” will be shown on your phone. 4. Select “ S2 ” (some mobile phones need you to input PIN “ 0000 ” as password ) and the headset will automatically connect with your mobile phone. ※Attention : Generally , there are 120 seconds at maximum to pair headset with your mobile phone, or the headset will power off automatically when the light goes out. Please retry steps 1 to 4 to pair again if your operation doesn’t work.  Disconnect the headset with your mobile phone: Switch off the headset. Or close the Bluetooth function of your mobile phone. Or take the headset from the phone to more than 20m ( 60ft ) away.  Reconnect the paired headset with your mobile phone: 1. Keep distance of the headset and mobile phone with in 1 meter. The closer, the better. 2. Switch on the headset, and ensure the headset enters into reconnection mode when the blue light blinks. 3. Switch on Bluetooth search function in your mobile phone of other device needed to be connected. Then the headset will automatically reconnect with the mobile phone which has connected last time.  Pair your headset with two mobile phone: 1. Keep distance between the headset and mobile phone 1 ( or other device needed to be connected ) within 1 meter. The closer, the better. 2. Ensure that the headset enters into pairing mode. The blue and red lights blink alternatively. 3. Switch on Bluetooth search function of phone 1, then pair headset with phone 1. 4. Turn off the Bluetooth function in your phone 1 and the headset. 5. Restart the headset and ensure the headset enters to pairing mode. Initiate Bluetooth function in your phone 2 and connect it with the headset. 6. Turn on the Bluetooth search function in your phone 1 and connect it with the paired headset. Then the headset will connect with two mobile phones at the same time.  Answer incoming call: Press the MF button once to answer the call. Or use your mobile phone to answer it.  Voice command: The headset will issue “ YES ” or “ NO ” when there is an incoming call. Speak “ YES ” to answer it or “ NO ” to reject it.  Hang up call: Press the MF button once or use your mobile phone to hang up your call.  Reject a call: When there is an incoming call, the headset will issue a sound, keep pressing the MF button for around 2 seconds, then release or use you mobile phone to reject the call.  Voice dialing: ( Please make sure your mobile phone supports this function ) Keep pressing the MF button for 2 seconds, then release, your mobile phone will enter into the voice dialing interface.  Last call redialing: Double – click the MF button.  Voice switch :( English and Chinese ) Under paring mode, keep press the MF button and VOL ( ‐ ) at the same time to achieve it.  Three – way calling: ( Please make sure whether your phone supports this function) 1. When mobile phone 1 is in conversation, there comes a call from mobile phone 2; pressing the MF button once. And you can answer the call from mobile phone 2, and the conversation of mobile phone 1 will be dropped. 2. When mobile phone 1 is in conversation, there comes a call from mobile phone 2; pressing the MF button for 2 seconds. You can answer the call from mobile phone 2; and keep the conversation of mobile phone 1. 3. When mobile phone 1 is in conversation, you can keep pressing the MF button for around 2 seconds. The headset will be switched back to mobile phone 1. 4. When mobile phone 2 is in conversation and the mobile phone 1 is reserved. Press the MF button once, you can answer the call for mobile phone 1, and the conversation of mobile phone 2 will be dropped.  Music play / pause: Press the MF button once to play / pause music.  Volume adjustment / Music selection: Keep presses the VOL (+) and VOL (‐) to adjust volume. Press VOL (+ ) and VOL ( ‐ ) once to select previous track or next track. FAQ: 1. Headset cannot pair with mobile phone. Ans: please check whether your headset is in pairing mode or reconnection mode, check whether Bluetooth search function of you mobile phone has been opened. Thus, check your mobile device’s Bluetooth menu and delete / forget the headset, reconnect the headset following instructions of user manual. 2. Headset cannot be switch on. Ans: Please check the battery status of your headset. 3. Can I change battery for the headset? Ans: No, this headset use a built – in non – detachable Li – Polymer battery, it cannot be removed. 4. Can I use headset while driving? Ans: For safety reason, we strongly recommend not to use over – ear headset to avoid distraction while driving. 5. Headset disconnect with your mobile phone within 10 meter. Ans: Please check if there is metal or other material within relatively close range may interfere Bluetooth connection, as Bluetooth is a radio technology that is sensitive to objects between the headset and the connected device. 6. Cannot hearing a sound from your computer or mobile phone. Ans: Please check whether the output channel of your computer is Bluetooth Audio Device and Bluetooth function of your computer support A2DP profile. And please check volume of your headset, and computer / mobile phone. 7. Cannot use the headset to control volume or select track of APP of your mobile phone. Technical Specification Ans: Software settings of APP may be varied led to some functions of the APP may not control by the headset  Specification:  Bluetooth version: Bluetooth V3.0  Frequency range: 2.4 GHz – 2.48 GHz  Operating distance: up to 10m ( free space )  Standby time: up to 180hrs  Talking / music – playing time: about 5 hours  Charging time: about 2hours  Bluetooth profiles: A2DP 、AVRCP 、HSP 、Hfp  Frequency response: 20Hz – 20kHz  Operational temperature: ‐ 10 to 50℃ Technical specifications are subject to change without notice, we apologize for any inconvenience. FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference. 2.This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Radiation Exposure Statement: This equipment complies with FCC radiation exposure requirement. The device can be used in portable exposure condition without RF striction 
Download PDF