Introducing a Whole New Category
of Power Protection
Introducing
a Whole New Category
of Power Protection
Go Beyond Surge Suppressors
The new SurgeGate™ from ITW Linx brings you a higher level of protection
from power fluctuation hazards. It makes surge suppressors obsolete.
It saves you money on service calls.
It increases your system uptime.
It protects your equipment when surge protectors don’t.
SurgeGate is totally unique:
The ONLY power protector to close the gate on both over-voltage and under-voltage
The ONLY power protector to automatically reset when the power returns to normal
The ONLY power protector to protect its own circuitry
Your Options/Your Consequences
Severe or
Extended Surge
SurgeGate Alone
Conventional Surge
Suppressor Alone
SurgeGate + UPS
• Power shut off avoids system
damage
UPS Alone
No Protection
After Many Surges
Under-Voltage
• Immediate surge suppresion
• Immediate surge suppresion
• Immediate surge suppresion
• Power resets after surge
• SurgeGate protects suppresion
circuits
• SurgeGate protects suppresion
circuits
• SurgeGate protects suppresion
circuits
• Surge suppresor destroyed
• Immediate surge suppression
• Suppression circuit fails
• No protection from surge suppressor
• Catastrophic system failure
• Suppression circuit degenerates
over time
• SurgeGate protects suppression
circuits
• System malfunction or damage
• Power shut off
• Immediate surge suppression
• Immediate surge suppression
• Power shut off
• Power reset
• SurgeGate protects suppression
circuits
• SurgeGate protects suppression
circuits
• Power reset
• Surge suppressor destroyed
• Immediate surge suppression
• Supression circuit fails
• No protection from surge suppressor
• Possible UPS failure
• Suppression circuit degenerates
over time
• Suppression circuit in UPS
degenerates
• UPS keeps your system up & running
• UPS keeps your system up & running
Conventional Surge
Suppressor + UPS
Typical Surge
• Possible system damage
• UPS keeps your system up & running
• Possible system damage
• Possible UPS damage
• Immediate surge suppression
• UPS suppression circuit fails
• Possible system damage or failure
• UPS suppression circuit degenerates
over time
• System damage or failure
• Catastrophic system failure
• System damage
• System failure
• UPS keeps your system up & running
• System malfunction or damage
*Predicted results based on high-end surge suppressor and mid-rang
1. Over-voltage: DISCONNECT power
1
2
OVER-VOLTAGE
SAFE VOLTAGE
2. Safe voltage: RECONNECT power
3. Under-voltage: DISCONNECT power
UNDER
VOLTAGE
4. Safe voltage: RECONNECT power
SurgeGate Benefits Installers
If you install telecomm and/or IT systems, unnecessary service calls can undercut the profits of your
service contracts. SurgeGate eliminates many power-related service calls because it resets itself. And
3
Typical Service Call Expenses
600
the increased uptime for your customers reflects well on you!
500
■ Low-End
Cumulative
SurgeGate Benefits Users
400
■ High-End
Cumulative
If it’s your equipment, you want increased uptime and lowered expense. SurgeGate provides both.
300
It protects your systems, automatically resets, and lasts years longer than a conventional surge
suppressor.
Why Gamble?
Electronic equipment is subject to about one hundred twenty power anomalies per month.* These are
caused by lightning, transformer changes on the power grid, electric motors starting up or shutting
down, static electricity or power line crosses. Voltage sags and brownouts pose an equal threat. Can
you afford damage to your equipment when your business depends upon it? Visit www.surgegate.
com to see SurgeGate and conventional surge suppressors in action on video.
*Source: IBM study conducted at 200 locations across the US.
4
200
100
0
SurgeGate
from
ITW Linx
SurgeGate™ Technology Shuts Down Power Damage
The First REAL Protection
Against Electrical Damage
For complete information on all the SurgeGate Power
Protection products and options, visit www.itwlinx.com
Utility power suffers approximately
120 surges/sags per month.
AC POWER
fter Many Surges
COMMON GROUND
The SurgeGate tests your
line for a reliable ground,
and it shares that ground
with the add-on modules
for a highly effective
protective system.
MOVs in conventional
surge circuits degenerate
with extended and repeated
surges. Our MOVs last long,
because they are protected.
Within milliseconds, the surge
is cut off at the SurgeGate
circuit.
Protect Or Disconnect
circuitry provides the
failsafe for the most
catastrophic events. Even for
a direct lightning strike, it
completly dissconnects AC
power to the connected
equipment and to the
protector.
SurgeGate options and
modules offer auto resetting
surge protection for data
networks, telephone, and T1.
This optimized circuitry
ensures a clean, clear signal
and features solid-state
suppressors for maximum
protection and reliability
1
2
3
UNDER-VOLTAGE
OVER-VOLTAGE
SAFE VO
LTAGE
4
Patented! All new!
SurgeGate technology allows only
safe power through. If the voltage
rises above 147V or dips below 87V,
SurgeGate cuts it off within
milliseconds.
SURGEGATE CIRCUITRY
MOV
FUSE
SURGE SUPPRESSOR CIRCUITRY
When the voltage returns to the
safe zone, SurgeGate resets
automatically and restores the
flow of power. And it continues
to do so for years of service.
First defense!
Within nanoseconds!
SurgeGate power protectors
also contain high quality surge
suppressor circuits that shunt surges
to ground within nanoseconds.
State-of-the-art noise filtration for
Electro Magnetic Interference/Radio
Frequency Interference, rated at
50db (99.97%).
EMI/RFI NOISE FILTRATION
With SurgeGate, you get nothing
but safe power. Used in conjunction
with a UPS, you get the best,
constant power. SurgeGate also
protects the UPS battery for longer
life.
PROTECT OR DISCONNECT™
FAILSAFE CIRCUITRY
POWER
OUTPUT
SIGNAL PERFECT
CIRCUITRY: TELCO, T1,
SATELLITE, LAN
YOUR SYSTEMS
SurgeGate guarantees your
systems get the best protection
and the most uptime. And we
insure your equipment against
power-related damage up to
$50,000.
AC SurgeGate™
Bubble of Protection
Alarm
System
Security Alarm
*
B PERIPHERAL DEVICES
PC
*
*
Fax
Dial - up
Modem
4 Wire
Leased Line
CO Lines
T1 or
Leased Lines
E
Q
U
I
P
L
I
N
E
CAT5-LAN
E
Q
U
I
P
L
I
N
E
DS/2
E
Q
U
I
P
L
I
N
E
CO/4
E
Q
U
I
P
L
I
N
E
LL/T1
E
Q
U
I
P
T0 T1
Telco Primary
Protector
and
Connection
Block
L
I
N
E
CO/4-110
E
Q
U
I
P
L
I
N
E
CO/25
POE Connection
LAN Connection
Digital Station Sets
Analog Lines
KSU Chassis Ground
Utility
Pole
CAT6-POE
Digital Phone
To Remote Bldg.
*
L
I
N
E
T1
Leased Line
Ground
C
O
E
Q
U
I
P
KSU
L
I
N
E
S
L
I
N
E
DS/2
E
Q
U
I
P
On-Premise
Station Sets
(With No AC
Connection)
RS-232 Line
L
II
N
E
S
Printer
Primary
Protector
S
T
A
T
I
O
N
UPS
Station
Set
A REMOTE BUILDING
To Properly
Grounded
Outlet
Features:
• AC protection for telecomm & computer systems
• Diagnostic indicator lights (four)
• Patented SurgeGate circuitry
• Eight foot power cord with right angle plug
• Protect or disconnect circuitry
• EMI/RFI noise filtration
• Expandable protection using SurgeGate modules
• 50,000 Connected Equipment Warranty
* To protect equipment marked (*) additional protectors are required.
TECHNICAL SPECIFICATIONS
4/8 outlet
2 outlet
Model Number
M4KSU/M8KSU/M8COM/M4L-POE M2T
Agency Approval
UL 1363, 1449
UL 1363, 1449
LED Indicators
4
2
Grounding Requirements
Uses Electrical AC Ground
Uses Electrical AC Ground
Product Warranty
Lifetime
Lifetime
Connected Equipment Warranty
Up to $50,000
Width / Height / Depth / Weight
3.5” / 5.5” / 2” / 0.74 lbs
AC POWER PROTECTION:
Thermal Fusing
Yes
Yes
Catastrophic Surge Circuit
Yes
Yes
Overvoltage Voltage Shutoff
147V ±8V
Undervoltage Voltage Shutoff
87V ±8V
Single Pulse Energy Dissipation
1650 Joules
1350 Joules
Peak Impulse Current
52,000 A
52,000 A
EMI/RFI Noise Filtration
50db (99.7%)
50db (99.97%)
Line Voltage
120V (50/60Hz)
120V (50/60Hz)
Initial Clamping Level
200V Peak, 141 Rms
200V Peak, 141 Rms
UL 1449 Rating
330V
400V
Protection Modes
L-N, L-G, N-G
L-N, L-G, N-G
Maximum Current Rating
15A (1800W)
15A (1800W)
Response Time
1–5 Nanoseconds
1-5 Nanoseconds
Number of Outlets
4-outlet
Model M4L-POE with one
POE (Power Ethernet) line
protection
2-outlet
Model M2T 2-outlet AC
protector, with Protect or
Disconnect circuitry and
integrated cable
management. Plus
UTLET MODELS
protection for one
telephone or DSL Line.
UTLET MODELS
Base unit Model 4KSU
features four switched AC
power
outlets.
Base unit
Model 4KSU
4-outlet
features four switched AC
Base outlets.
unit Model M4KSU
power
features four switched AC
power outlets.
2
SIGNAL LINE SURGE PROTECTION:
TELCO CIRCUIT PROTECTION (if included)
UTLET MODELS
UTLET MODELS
Signal Perfect Circuitry
Yes
Yes
Fuseless/Auto-Resettable
Yes
Clamping Level
260V
Response Time
1–5 Nanoseconds
Capacitance
<50pF
<20pF
Suppression Modes
Metallic & Longitudinal
Metallic & Longitudinal
Wires Protected
2-wire, 1-pair (pins 3, 4)
2-wire, 1-pair
Termination Type
RJ-11
RJ-11/45
Base
Yesunit Model 4KSU
features
four switched AC
260V
power
outlets.
1–5 Nanoseconds
Base unit Model M8KSU
UTLET MODELS
features eight AC power
8-outlet
outlets.
Base unit Model M8KSU
Base unit
M8KSU
features
eightModel
AC power
features eight AC power
outlets.
outlets.
SIGNAL LINE SURGE PROTECTION (Telco &T1/LL)
Signal Perfect Circuitry/Fuseless
Yes
Clamping Level (TELCO)/(T1LL)
260V/70V
Response Time
1–5 Nanoseconds
Capacitance (TELCO)/(T1LL)
<50pF
Suppression Modes
Metallic & Longitudinal
UTLET MODELS
Wires Protected
(TELCO)
(T1/LL)
Base unit Model M8KSU
features eight AC power
1 pair per jack, total 5 Telco jack (pins 4, 5)
outlets.
Termination Type
(TELCO)
RJ-11/45
(T1/LL)
RJ-45
(POE)
RJ45 65V Clamping (M4L-POE)
Pins 1, 2, 4, 5
LAN CIRCUIT PROTECTION (if included)
Signal Perfect Circuitry
Yes
Fuseless/Auto-Resettable
Yes
Performance Rating
Category 5
Clamping Level
7V
Response Time
1–5 Nanoseconds
Wires Protected
8-wires (pins 1–8)
Termination Type
RJ-45
Model M8COM-60 adds
8-outletprotection for
telephone
four
voiceM8COM
or DSL lines;
Model
addsT1
protection
for protection
one T1 or for
telephone
LLfour
line;voice
LAN or
protection
DSL lines; T1
for
one 10/100BASE-T
protection
for one T1 or
Ethernet
LL line;line.
LAN protection
for one 10/100BASE-T
Ethernet line.
-
Modular Protection
TELCO CIRCUIT PROTECTION
Product Specifications:
Agency Approval
Grounding Requirements
Recommended Ground Impedance
Width
Height
Depth
Signal Perfect Circuitry
Auto-Resetting PTCs
Clamping Level
Response Time
Capacitance
Suppression Mode
(unless otherwise noted) UL 497A (Secondary)
Uses AC Ground via SurgeGate Base Units
<0.5 Ohm
(unless otherwise noted) 4.25”
(unless otherwise noted) 4.25”
1.5”
Yes
160 mA (8–10 Ohms)
(unless otherwise noted) 260V (T-R, T-G, R-G)
1–5 Nanoseconds
< 50pF
(unless otherwise noted) Metallic and Longitudinal
Features:
• Auto-Resetting Technology—PTC resistors open when a surge occurs, protecting your equipment,
but unlike fuses, the PTCs close again once the surge passes. Less downtime, and less service calls.
• Expandable System Protection—SurgeGate Series Base Units and Modules can be attached to expand
system protection as your system grows.
• Lifetime Product Warranty.
• $50,000 Connected Equipment Warranty— This ITW Linx product will protect your equipment or we
will repair or replace it up to $50,000!
Product Specifications:
MCO4—ANALOG STATION SET AND CENTRAL OFFICE LINE PROTECTOR
Protects up to 4-wires (2-pairs) using RJ-11/45 connectors (2 In/2 Out, Pins 3 & 6 and 4 & 5 protected).
MCO4X4—ANALOG STATION SET AND CENTRAL OFFICE LINE PROTECTOR
Protects up to 4-wires (2-pairs) using RJ-11/45 connectors, one line protected per jack (pins 4, 5).
MCO25—ANALOG STATION SET AND CENTRAL OFFICE LINE PROTECTOR
Protects 25-pairs using RJ-21X (Amphenol) connectors (pins 1–50, Male In / Female Out). Height: 5.87”
MCO4110—ANALOG STATION SET AND CENTRAL OFFICE LINE PROTECTOR
Protects up to 8-wires (4-pairs) using 110 punchdown block on the input and 110 punchdown block or four RJ-11 or two RJ-45 on the Output.
Width: 5.87”
MCO8110—ANALOG STATION SET AND CENTRAL OFFICE LINE PROTECTOR
Protects up to 16-wires (8-pairs) using 110 punchdown block on the Input and 110 punchdown block on the Output. Width: 5.87”
MDS25—DIGITAL STATION SET PROTECTOR
Protects up to 25 2-wire or up to 12 4-wire digital stations lines using RJ-21X (Amphenol) connectors (pins 1–50, Male In /
Female Out). Height: 5.87” Clamping Level 110V (T-G, R-G, T-R)
MLLT1—HIGH-SPEED DIGITAL T1 OR LEASED LINE PROTECTOR
Protects up one T1 or ISDN line per port using RJ-48C/48S connectors. T1/LL—2-pairs (pins 1, 2 & 4, 5); ISDN—BRI/PRI
compatible. Clamping Level: 70V; Wires Protected: 4-wires, 2-pairs per jack (pins 1, 2 & 4, 5)
BUILDING ENTRANCE AND
LAN CIRCUIT PROTECTION
Product Specifications:
Agency Approval
Grounding Requirements
Recommended Ground Impedance
Width
Height
Depth
Signal Perfect Circuitry
Fuseless/Auto-Resettable
Response Time
Capacitance
UL Primary (497) and Isolated Loop (497B)
Uses AC Ground via SurgeGate Base Units
<0.5 Ohm
4.25”
4.25”
1.5”
Yes
Yes
1–5 Nanoseconds
< 20pF
Features:
• UL Listed for Primary (497) and Isolated Loop (497B) applications.
• CAT6 products exceed TIA/EIA Standards 568 and 758 for category 5e performance.
• CAT6 products exceed TIA/EIA Standards 568B.2-1 and 758 for category 6 performance.
• Solid-state protection provides the fastest response to transient voltages (1-5 nanoseconds)
by quickly diverting damaging surges to ground.
• Use between buildings in a campus environment as a building entrance protector or in a
hostile industrial applications as an isolated loop protector.
• Expandable System Protection - SurgeGate Series Base Units and Modules can be attached
to expand system protection as your system grows.
• Lifetime Product Warranty.
• $50,000 Connected Equipment Warranty-This ITW Linx product will protect your equipment
or we will repair or replace it up to $50,000!
Product Specifications:
CAT6-75-RJ45 POE 110/RJ45
Protects high-performance (4 Pair) CAT6 + CAT5e Outside Plant Cables as well as Category 5e UTP cables for Power Over
Ethernet applications. For mid-span applications where power and data are seperate. Clamping level: 75V, Type: 110 IN RJ-45 OUT
CAT6-75 - RJ45 / POE
Protects high-performance (4 Pair) CAT6 + CAT5e Outside Plant Cables as well as Category 5e UTP Cables for voice or ISDN low-voltage (digital,
75V clamping) applications. Termination Type (CAT6): Termination Type RJ45 IN + OUT
CAT6-LAN-RJ45
Protects (4 Pair) CAT5e + CAT6 RJ45, 16V, Termination RJ45 IN + OUT
CAT6-235
Protects (4 Pair) CAT5e + CAT6, voice / ISDN / Analog, 110 Punchdown IN + OUT, 235V clamping
CAT6-235-RJ45
Protects (4 Pair) CAT5e + CAT6 for voice / ISDN / Analog, RJ45 IN + OUT, 235V clamping
CAT6-LAN
Protects (4 Pair) CAT5e + CAT6, 110 Punchdown IN + OUT, 16V clamping
CAT6-75
Protects (4 Pair) CAT5e + CAT6 rated cable, 110 Punchdown IN + OUT, 75V clamping (POE)
CAT6A-LAN
Protects (4 Pair) CAT6A outside plant cables + CAT6A UTP cables for LAN/DATA applications, 16V clamping 110 Punchdown IN + OUT
CAT6-LAN-MM
Protects (4 Pair), Solid State CAT5e + CAT6-LAN application with 16 volts clamping voltage, Metal Housing RJ45 IN + OUT
CAT6-75/POE-MM
Protects (4 Pair), Solid State CAT5e + CAT6 with 75 clamping voltage for digital / POE applications, Metal Housing RJ45 IN + OUT
CAT6-235-MM
Protects (4 Pair), Solid State CAT5e + CAT6 with 235 clamping voltage for T1, Telco and analog lines, Metal Housing RJ45 IN + OUT
IP/NETWORK CAMERA
SURGE PROTECTION
GND
SurgeGate
secondary protector
L
I
N
E
MSL-CAT5-24V
E
Q
U
I
P
M
E
N
T
800-336-LINX • www.itwlinx.com
ITW Linx RM12 Protector
RM-12MPVD
SurgeGate
primary
protector
GND
SurgeGate
primary
protector
SurgeGate
L
I
N
E
MSL-CAT5-24V
E
Q
U
I
P
M
E
N
T
800-336-LINX • www.itwlinx.com
SurgeGate
protector
M4KSU
SurgeGate Protectors:
Part Number:
RM-12MPVD (Housing) or RM6-MPVD
RM12-CAT6-LAN
RM12-CAT6-75/POE
RM12-CAT6-235
Description:
Modular Rack - up to 12 individual protection modules
Protection Module, Solid State CAT6-LAN application with 16 volts clamping voltage
Protection Module, Solid State CAT6 with 75 clamping voltages for digital / POE applications
Protection Module, Solid State CAT6 with 235 clamping voltage for T1, Telco and analog lines
SurgeGate™ Modular
Wall Mount
Features:
• UL Listed for Primary (497) and Isolated Loop (497B) applications
• Exceeds TIA/EIA Standards 568 and 758 for CAT 5e and CAT 6 (depending
on module ordered) performance
• Solid-state protection provides the fastest response to transient voltages
(1-5 nanoseconds) by quickly diverting damaging surges to ground
• Use between buildings in a campus environment as a building entrance
protector or in hostile industrial applications as an isolated loop protector
• Up to 6 individual and replaceable port modules
• RJ45 input to RJ45 output
• Single-height wall mountable chassis (1U) - Protectors sold separately
dependant on application
• Suggested Applications Include: Security cameras, POE, Phone systems,
Ethernet, & VOIP
TECHNICAL SPECIFICATIONS
PRODUCT SPECIFICATIONS:
Agency Approval
UL Primary (497) and Isolated Loop (497B)
Grounding Requirements
Field installed solid copper wire
#6 AWG for Primary
#14 AWG for Isolated Loop
Recommended Grounding Impedance
<0.5 0hm
Height/Width/Depth
2.1 / 4.0 / 10.25
Weight w/o Modules
2.0lbs.
Product Warranty
Lifetime
Connected Equipment Warranty
Up to $5,000
SINGLE LINE SURGE PROTECTION: (LAN)
Signal Perfect Circuitry
Yes
Fused
No
Performance Rating
CAT5e/CAT6 (Gigabit) Depending on Module Ordered
Clamping Level
CAT5 or CAT6 LAN = 16V
CAT5e or CAT6 75/POE = 75V
CAT5e or CAT6 235 = 235V
Response Time
1-5 Nanoseconds
Capacitance
<20pF
Wires Protected
8-wires, 4-pairs per port
Termination Type
RJ-45 In & Out
ORDERING INFORMATION
Part Number
Description
RM-6MPVD
Modular Wall - up to 6 individual protection modules
RM12-CAT6-LAN
Protection Module, Solid State CAT6-LAN application with 16 volts clamping voltage
RM12-CAT6-75/POE
Protection Module, Solid State CAT6 with 75 clamping voltage for digital / POE applications
RM12-CAT6-235
Protection Module, Solid State CAT6 with 235 clamping voltage for T1, Telco and analog lines
*Questions about ordering? Please contact us at 1-800-278-5666 / Contact an authorized distributor for pricing* (MOQ:6)
SurgeGate™
Modular Rack Mount
TECHNICAL SPECIFICATIONS
PRODUCT SPECIFICATIONS:
Agency Approval
UL Primary (497) and Isolated Loop (497B)
Grounding Requirements
Field installed solid copper wire
#6 AWG for Primary
#14 AWG for Isolated Loop
Recommended Grounding Impedance
<0.5 0hm
Height/Width/Depth
1.7”/19”/4.0”
Weight w/o Modules
2.9lbs.
Product Warranty
Lifetime
Connected Equipment Warranty
Up to $5,000
Features:
• UL Listed for Primary (497) and Isolated Loop (497B) applications
• Exceeds TIA/EIA Standards 568 and 758 for CAT 5e and CAT6
(depending on module ordered) performance
• Solid-state protection provides the fastest response to transient
voltages (1-5 nanoseconds) by quickly diverting damaging surges
to ground
• Use between buildings in a campus environment as a building
entrance protector or in hostile industrial applications as an isolated
loop protector
• Up to 12 individual and replaceable port modules
• RJ45 input to RJ45 output
• Single-height rack mountable chasis (1U)
SINGLE LINE SURGE PROTECTION: (LAN)
Signal Perfect Circuitry
Yes
Fused
No
Performance Rating
CAT5e/CAT6 (Gigabit) Depending on
Module Ordered
Clamping Level
CAT5 or CAT6 LAN = 16V
CAT5e or CAT6 75/POE = 75V
CAT5e or CAT6 235 = 235V
Response Time
1-5 Nanoseconds
Capacitance
<20pF
Wires Protected
8-wires, 4-pairs per port
Termination Type
RJ-45 In & Out
ORDERING INFORMATION
Part Number
RM-12MPVD
Description
Modular Rack - up to 12 individual protection modules
Protection Module, Solid State CAT6-LAN application with 16 volts clamping
voltage
RM12-CAT6-75/POE Protection Module, Solid State CAT6 with 75 clamping voltage for digital /
POE applications
RM12-CAT6-235
Protection Module, Solid State CAT6 with 235 clamping voltage for T1, Telco
and analog lines
RM12-CAT6-LAN
UltraLinx™ Series
66 Block Surge protector
SECONDARY
PROTECTION
DIGITAL
STATION SETS*
PRIMAR Y
PROTECTION
FAX*
UTILITY POLE
COMPUTER
WITH MODEM*
KSU CHASSIS
GROUND
CO INCOMING LINES
TELCO
PRIMAR Y
PROTECTOR
AND
DEMARCATION
POINT
MULTIPLE GROUND
BUS BAR
GROUND
C
O
L
I
N
E
S
PBX/
KSU
S
T
A
T
I
O
N
L
I
N
E
S
L
I
N
E
CO/4
E
Q
U
I
P
L
I
N
E
DS/2
E
Q
U
I
P
L
I
N
E
CO/4X4
E
Q
U
I
P
L
I
N
E
CO/25
E
Q
U
I
P
ULTRALINX
TELCO
PRIMAR Y
PROTECTOR
PROTECTORS ON
STANDARD 66 BLOCK
WITH ATTACHED MULTIPLE
GROUND BUS BAR
ULTRALINX
PRIMAR Y PROTECTOR
UPS
TELCO
GROUND
PROTECTION OK GROUND OK
UltraLinx
UP3B-7.5
GND
800-336-LINX itwlinx.com
PATENTED: 7050285
UL
TELEPHONE
PROTECTOR
58S7
PRIMAR Y
PROTECTION
TO REMOTE
LOCATIONS
TO REMOTE
LOCATIONS
ULTRALINX
LISTED
ANALOG
STATION SETS*
SURGEGATE 4 KSU
CONNECTED TO A PROPERLY
GROUNDED OUTLET
GROUND STATUS
PUSH BUTTON
LINE EQUIP.
L
I
N
E
DS/2
E
Q
U
I
P
ON-PREMISE
STATION SETS
(WITH NO AC
CONNECTION)
STATION
SET
REMOTE BUILDING
TO REMOTE LOCATIONS
Features:
• Dual Indicator Lights - Protection OK and Ground
Connection OK
• Cost Savings - Eliminate expensive five-pin blocks and use
economical 66 Blocks
• Solid-state Protection - Provides the fastest response
• Optimum Protection - Available in a number of voltage
ratings to match system operating voltages
• Single Pair Protection - Scale the protection to the system
size. Protect only the lines requiring protection
• Streamlined Installation- Eliminate redundant
cross-connects by adding protection directly at
the 66 Block. Press fit protectors to the block
and attach the ground bar to the protectors.
MGBSGL-1 Comes with Screw Ground Lug.
• Sneak Current Protection - Protects against fires caused by
overloads and power crosses
• Ideal for Retrofit Applications - Just remove the
bridging clips from the block & replace them
with the UltraLinx Protector, add the ground
connection and the pair is protected
• Lifetime Product Warranty - This surge protector shall be
free of any defects in design, materials, or workmanship, or
ITW Linx will repair or replace the defective product
TECHNICAL SPECIFICATIONS
Agency Approval
LED Indicators / Sneak Current Protection
Grounding Requirements
Recommended Grounding Impedance
PTC Rating
Fuse Rating
UP3B
UP3P
UL 497 (Primary), 497A (Secondary)
Yes
Field installed solid copper wire
for Primary 1-6 pairs 10 AWG
for Primary 7-25 pairs 6 AWG
for Secondary 1-6 pairs 14 AWG
for Secondary 7-25 pairs 6 AWG
<0.5 Ohm
UL 497A (Secondary)
for Secondary 7-25 pairs 6 AWG
<0.5 Ohm
160mA (8-10 Ohms)
350mA
1.6 Ohms
Applications
Data / Voice / Fax / Modem lines
Width / Height / Depth / Weight
Product Warranty
1.88” / 2.62” / 0.38” / 0.04 lbs
Lifetime
SIGNAL LINE SURGE PROTECTION: (TELCO)
Signal Perfect Circuitry
Auto-Resettable
Clamping Level
Response Time
Capacitance
Suppression Modes
Wires Protected
Termination Type
Yes
Field installed solid copper wire
for Secondary 1-6 pairs 14 AWG
Data / Voice / Fax / Modem
lines
1.88” / 2.62” / 0.38” / 0.04 lbs
Lifetime
Yes
Yes
Yes
7.5V, 16V, 27V, 39V, 75V, 100V, 235V
1-5 Nanoseconds
<50pF
Metallic & Longitudinal
2-wires, 1-pair
66 type M Blocks
27V, 39V, 75V, 235V
1-5 Nanoseconds
<50pF
Metallic & Longitudinal
2-wires, 1-pair
66 type M Blocks
UP3P
ORDERING INFORMATION
ITW Linx Part Number
Description
UP3P-27
UL Secondary listed with 160mA PTC for voice / fax / modem lines (27V).
UP3P-39
UL Secondary listed with 160mA PTC for voice / fax / modem lines (39V).
UP3P-75
UL Secondary listed with 160mA PTC for voice / fax / modem lines (75V).
UP3P-235
UL Secondary listed with 160mA PTC for voice / fax / modem lines (235V).
UP3B-7.5
UL Primary & Secondary listed with 350mA fuse for voice/fax/modem line (7.5V).
UP3B-16
UL Primary & Secondary listed with 350mA fuse for voice/fax/modem line (16V).
UP3B-27
UL Primary & Secondary listed with 350mA fuse for voice/fax/modem line (27V).
UP3B-39
UL Primary & Secondary listed with 350mA fuse for voice/fax/modem line (39V).
UP3B-75
UL Primary & Secondary listed with 350mA fuse for voice/fax/modem line (75V).
UP3B-100
UL Primary & Secondary listed with 350mA fuse for voice/fax/modem line (100V).
UP3B-235
UL Primary & Secondary listed with 350mA fuse for voice/fax/modem line (235V).
UP3B
Surge Protection Solutions
www.itwlinx.com
ITW Electronic Component Solutions - ITW Linx
425 N. Gary Ave. Carol Stream, IL. 60188.
Phone: 1-800-278-5666
Download PDF