User Manual of ATC-1000

3.6 Connection Diagram
3.0 . Hardware Installation & Initial Setup
RS-232 Connection
3.1 RS-232 Configuration:(DB9 Male)
Model XS1000
TCP/IP to RS232/422/485 Device Server
User’s Manual
(DB9Male)
Signal
I/O
PIN2
RXD
IN
PIN3
TXD
OUT
PIN5
GND
-
PIN7
RTS
OUT
PIN8
CTS
IN
3.2 RS-422/485 Configuration:(terminal header)
Terminal
1.0 Introduction
No
1
2
3
4
5
6
The XS1000 is a cost effective and highly integrated
RS-422
T+
T-
R+
R-
VIN
GND
Serial-to-Ethernet 10/100Mbps device server. Embedding a
RS-485
485+
485-
-
-
VIN
GND
RS-422 Connection
8051CPU with 64KB OTP ROM and 32KB SRAM. The serial
interface supports handshake signals RTS and CTS. The
3.3 Connecting to 10/100M:
XS1000 can access a serial RS232/422/485 device located
Use a standard Ethernet cable to connect the XS1000 to an
virtually anywhere (via Ethernet or Internet). It automatically
Ethernet switch, or use a cross-over cable if you connect it
finds devices on the network and can be configured by a
directly to a PC.
web-browser.
3.4 Power Supply:
2.0 Features:
♦ 3-in-1 RS-232/422/485 interface Max.230Kbps Serial
The XS1000 needs a 9 to 24VDC 1000mA power supply.
interface and 10/100 Mbps Ethernet.
♦ Supports 4- and 2-wire RS-485 with AUTO-SEND™.
♦ Terminal block for easy RS-422/485 serial wiring
♦ Supports IP configuration by MAC address.
♦ Supports Driver, TCP Server/Client, UDP Server/Client and
3.5 XS1000 LED indication:
LINK:
Ethernet Link established.
ACT:
Data flow TX/RX.
PWR:
Power ON.
Pair Connection protocols.
♦ Easy and powerful configuration management.
♦ Approvals: CE, RoHS.
Copyrights © U.S. Converters
RS-485 Connection
DHCP. These types are listed in the Web page for the IP
4.
4.1
Configuration and Operation
The menu features as below:
Configuration settings. Each setup screen and available
features will differ depending on what kind of IP connection
A. Assign a static IP address to your computer in the
types you select. Default is Static IP
192.168.2.2 to 192.168.2.254 range. Subnet mask
255.255.255.0. This is necessary to ensure that your
computer can communicate with your XS1000. Your
computer must have an Ethernet card and TCP/IP installed.
B. The default IP address of the XS1000 is 192.168.2.1.
Open your web browser and enter this IP address to connect
to the XS1000.
C. Default user name is ‘admin’ and the password is ‘system’.
U
U
Click “OK”. The setup screen will then appear, and you can
now configure the settings.
D. Create a new COM port using VCOM.exe.
Menus explained:
Static (or Fixed) IP
4.2 Administrator Setup
IP Address: default 192.168.2.1
Main admin window.
Subnet mask: default 255.255.255.0
4.3
Gateway: default 192.168.2.254
Authentication
U
U
U
U
The user can change the username and password to prevent
Primary DNS: default 192.168.2.253
unauthorized access.
If you are connecting through a static or fixed IP from your
Login ID and password authentication, the maximum number of
network environment, perform these steps:
characters is 15, (characters and numbers).
Step 1: Enter IP address
User Name: default admin
Step 2: Enter Subnet mask
Password: default system
Step 3: Enter Gateway IP address
U
U
Step 4: Enter Primary DNS IP address
Step 5: click Update button
4.6 DHCP
Host Name (Optional): default NETUART, maximum
length 15 characters.
If there is a DHCP Server existing in your network
environment, you can set the IP configuration to DHCP to
get a dynamic IP address. The Host Name is an optional
4.3 System IP
The XS1000 support two IP connection types: Static IP and
Copyrights © U.S. Converters
item, depending on your DHCP Server setting.
guaranteed to be received by the peer is your concern, then
Remote Host IP Address: default 192.168.2.2
5.0 System Status
you can set the XS1000 as TCP Server . Be sure the value of
If your device is acting as an active device to report
This screen shows the XS1000’s current status. All of the
the setting Port Number is same as your remote control
real-time status to a remote device and the data be
information provided is read-only.
application using.
guaranteed to be received by the peer is not your
Kernel Version: the installed version of the kernel.
Client mode inactive timeout (minutes): default 20
concern, then you can set XS1000 as TCP Client. Be
MAC Address: The present device MAC Address.
( 0=Disable)
sure the value of item Remote Connection Port
Nickname: the product’s NetUART model name.
If you want to keep the connection between XS1000 and your
Number is same as your remote control application
remote control application always on, then set the value of item
using the correct value of Remote Host IP Address.
U
U
Client mode inactive timeout (minutes) to 0, otherwise,
when the inactive time of ‘no traffic’ on the line reach the
configured value, the XS1000 will terminate the connection.
5.4 TCP Client
Remote Connection Port Number: default 23, range 0 to
65535
5.0 Load default setting
Remote Host IP Address: default 210.200.181.102
Allows the user to reset the XS1000 to default settings. The
If your device is acting as an active device to report real-time
6.0 UART Control (RS-232)
MAC Address will not be updated.
status to remote devices and the data needs to be guaranteed
Use VCOM for creating a new COM port.
to be received by the peer is your concern, then you can set the
The XS1000 support three serial types: RS232, RS422 and
XS1000 as TCP Client . Be sure the value of the setting
RS485.
Remote Connection Port Number is same as your remote
Baud Rate: default 57600, range 300bps to 230.4Kbps.
5.1 Telnet
control application using the correct value of Remote Host IP
Character Bits: 5, 6, 7, 8 (default).
Currently not supported.
Address.
Parity Check: None (default), even, odd, space, mark.
5.2 Operation mode
5.5 UDP Server
Stop Bits: 1 (default), 1.5 or 2.
The XS1000 supports four operation modes: TCP Server,
Local Port Number: default 21, range 0 to 65535
Hardware Flow Control: None (default) or Hardware.
TCP Client, UDP Server and UDP Client. These modes
If your device is acting as a passive device to accept
are listed in the Web page for the Operation Mode setting.
commands from a remote device and the data needs to
U
U
Each setup screen and available features will differ
be guaranteed to be received by peer is not your concern,
depending on what kind of operation mode you select.
then you can set XS1000 as UDP Server. Be sure the
Default is TCP Server.
value of item Local Port Number is same as what your
5.3 TCP Server
remote application is using.
Port Number: default 23, range 0 to 65535
5.6 UDP Client
If your device is acting as a passive device to accept
Remote Connection Port Number: default 21, range 0 to
commands from a remote device and the data needs to be
65535
Copyrights © U.S. Converters
Mechanical dimensions
5mm
32,5mm
25m
94mm
XS1000
15mm
45mm
14mm
All mounting holes:
Ø3.5mm
66mm
26mm
Note to Admin Panel’s UART Control advanced settings:
Character 1 and 2: These are HEX numbers. Default value: 00FF. When sending data from serial to TCP the data is fist
stored in the cache, not until the value of character 1 or 2 is received from the serial side the data is released from the cache and sent to TCP.
Silent time: If there is no data sent or received for the number of milliseconds specified the connection is dropped.
Drop character: Drops the delimiter character of the serial port when sending to TCP, (the receiver doesn't display the character).
Copyrights © U.S. Converters
How to hardware reset XS1000
1. Disconnect the Ethernet cable.
2. Disconnect the serial cable.
3. Disconnect the power supply.
5. Locate the small hole next to the power supply jack. The reset button is inside the hole.
6. Press the reset button (using a paperclip or small screwdriver) and hold the reset button.
7. While pressing/holding the reset button connect the power supply.
8. The red Power LED light will come on and the green Link LED light will light up dimly for about 1 second.
9. Hold the reset button for about 10 seconds and release it. No LED light indication will show when the unit has been reset, you just have to hold the button for 10 seconds.
10. The XS1000 now has been reset to factory settings.
Notice: the unit can also be reset from the web interface.
To access technical support, please visit the U.S.
Converters website at:
www.USconverters.com
Here you will find:
- Latest drivers and updates for download
- Technical tips
- Documentation
- Configuration support
- and much more…
Feel free to contact our technical support team at
mail@usconverters.com with any issues.
Copyrights © U.S. Converters
Copyrights © U.S. Converters
Download PDF