HP Compaq 6820s Notebook PC

HP Compaq 6820s Notebook PC
Maintenance and Service Guide
© Copyright 2007 Hewlett-Packard
Development Company, L.P.
AMD, the AMD Arrow logo, and
combinations thereof, are trademarks of
Advanced Micro Devices, Inc. Bluetooth is a
trademark owned by its proprietor and used
by Hewlett-Packard Company under license.
Intel, Core, Celeron, and Pentium are
trademarks or registered trademarks of Intel
Corporation or its subsidiaries in the U.S. and
other countries. Java is a trademark of Sun
Microsystems, Inc. Microsoft, Windows, and
Windows Vista are either trademarks or
registered trademarks of Microsoft
Corporation in the United States and/or other
countries. SD Logo is a trademark of its
proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
Second Edition: December 2007
First Edition: September 2007
Document Part Number: 456943-002
MSG revision history
Revision
Publication date
Description
A
February 2010
The top cover, part number 457616-001, does not include the TouchPad board and
cable or the TouchPad button board and cable. This information has been updated
in the following locations: Computer major components on page 12, Sequential part
number listing on page 22, and Top cover on page 55. The TouchPad board and
cable are available using part number 457617-001. The TouchPad button board and
cable is available using part number 456601-001.
iii
iv
MSG revision history
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
v
vi
Safety warning notice
Table of contents
1 Product description
2 External component identification
Top components ................................................................................................................................... 5
TouchPad ............................................................................................................................ 5
Buttons, lights, and speaker ................................................................................................ 6
Keys ..................................................................................................................................... 7
Front components ................................................................................................................................ 8
Right-side components ......................................................................................................................... 8
Left-side components ........................................................................................................................... 9
Bottom components ........................................................................................................................... 10
3 Illustrated parts catalog
Serial number location ........................................................................................................................ 11
Computer major components ............................................................................................................. 12
Plastics Kit .......................................................................................................................................... 18
Cable Kit ............................................................................................................................................. 19
Mass storage devices ......................................................................................................................... 20
Miscellaneous parts ............................................................................................................................ 21
Sequential part number listing ............................................................................................................ 22
4 Removal and replacement procedures
Preliminary replacement requirements ............................................................................................... 27
Tools required .................................................................................................................... 27
Service considerations ....................................................................................................... 27
Plastic parts ....................................................................................................... 27
Cables and connectors ..................................................................................... 28
Drive handling ................................................................................................... 28
Grounding guidelines ......................................................................................................... 29
Electrostatic discharge damage ........................................................................ 29
Packaging and transporting guidelines ............................................. 30
Workstation guidelines ..................................................................... 30
Equipment guidelines ....................................................................... 31
vii
Unknown user password ................................................................................................... 32
Component replacement procedures ................................................................................................. 33
Serial number .................................................................................................................... 33
Computer feet .................................................................................................................... 34
Battery ............................................................................................................................... 35
Hard drive .......................................................................................................................... 36
WLAN module .................................................................................................................... 38
Memory module ................................................................................................................. 41
Optical drive ....................................................................................................................... 42
Switch cover and keyboard ................................................................................................ 45
Speaker ............................................................................................................................. 49
Display lid switch module ................................................................................................... 50
Display assembly ............................................................................................................... 51
Top cover ........................................................................................................................... 55
TouchPad board and TouchPad button board ................................................................... 58
Bluetooth module ............................................................................................................... 60
System board ..................................................................................................................... 61
Fan ..................................................................................................................................... 65
Heat sink ............................................................................................................................ 67
Processor ........................................................................................................................... 69
Modem module .................................................................................................................. 71
RTC battery ....................................................................................................................... 73
5 Computer Setup
Starting Computer Setup .................................................................................................................... 75
Using Computer Setup ....................................................................................................................... 76
Navigating and selecting in Computer Setup ..................................................................... 76
Restoring factory settings in Computer Setup ................................................................... 76
Computer Setup menus ..................................................................................................................... 77
File menu ........................................................................................................................... 77
Security menu .................................................................................................................... 78
Diagnostics menu .............................................................................................................. 78
System Configuration menu .............................................................................................. 79
6 Specifications
Computer specifications ..................................................................................................................... 80
17.0-inch, WXGA display specifications ............................................................................................. 81
Hard drive specifications .................................................................................................................... 82
DVD±RW and CD-RW Double-Layer Combo Drive specifications .................................................... 83
DVD/CD-RW Combo Drive specifications .......................................................................................... 84
System DMA specifications ................................................................................................................ 85
System interrupt specifications ........................................................................................................... 86
System I/O address specifications ..................................................................................................... 87
viii
System memory map specifications ................................................................................................... 89
7 Screw listing
Phillips PM2.0×5.0 captive screw ....................................................................................................... 91
Phillips PM2.5×13.0 captive screw ..................................................................................................... 92
Phillips PM3.0×4.0 screw ................................................................................................................... 93
Phillips PM2.5×4.0 screw ................................................................................................................... 94
Torx T8M2.5×7.0 screw ..................................................................................................................... 95
Phillips PM2.0×4.0 screw ................................................................................................................... 97
Torx T8M2.5×9.0 screw ..................................................................................................................... 99
Torx T8M2.5×3.0 broad-head screw ................................................................................................ 100
Torx T8M2.5×4.0 screw ................................................................................................................... 101
Torx T8M2.5×6.0 screw ................................................................................................................... 103
Phillips PM2.0×2.0 broad-head screw .............................................................................................. 105
Phillips PM2.0×6.0 screw ................................................................................................................. 106
Phillips PM2.5×7.0 screw ................................................................................................................. 107
Phillips PM2.5×7.0 captive screw ..................................................................................................... 108
Phillips PM2.5×10.0 captive screw ................................................................................................... 109
8 Backup and recovery
Creating recovery discs in Windows Vista ....................................................................................... 110
Backing up your information in Windows Vista ................................................................................ 111
When to back up .............................................................................................................. 111
Backup suggestions ......................................................................................................... 111
Backing up specific files or folders ................................................................................... 112
Backing up the entire hard drive ...................................................................................... 112
Creating recovery points .................................................................................................. 113
Scheduling backups ......................................................................................................... 113
Performing a recovery in Windows Vista .......................................................................................... 114
Performing a recovery from the recovery discs ............................................................... 114
Performing a recovery from the hard drive ...................................................................... 114
Initiating a recovery in Windows ...................................................................... 115
Initiating a recovery from the hard drive recovery partition ............................. 115
Creating recovery discs in Windows XP ........................................................................................... 116
Backing up your information in Windows XP .................................................................................... 117
When to back up .............................................................................................................. 117
Backup suggestions ......................................................................................................... 117
Backing up specific files or folders ................................................................................... 118
Backing up the entire hard drive ...................................................................................... 118
Creating recovery points .................................................................................................. 119
Scheduling backups ......................................................................................................... 119
Performing a recovery in Windows XP ............................................................................................. 120
Performing a recovery from the recovery discs ............................................................... 120
ix
Performing a recovery from the hard drive ...................................................................... 120
Initiating a recovery in Windows ...................................................................... 121
Initiating a recovery from the hard drive recovery partition ............................. 122
9 Connector pin assignments
Audio-out (headphone) ..................................................................................................................... 123
Audio-in (microphone) ...................................................................................................................... 123
External monitor ............................................................................................................................... 124
RJ-11 (modem) ................................................................................................................................ 125
RJ-45 (network) ................................................................................................................................ 125
Universal Serial Bus ......................................................................................................................... 126
10 Power cord set requirements
Requirements for all countries and regions ...................................................................................... 127
Requirements for specific countries and regions ............................................................................. 128
11 Recycling
Battery .............................................................................................................................................. 129
Display .............................................................................................................................................. 129
Index ................................................................................................................................................................. 135
x
1
Product description
Category
Description
Product Name
HP Compaq 6820s Notebook PC
Processors
Intel® Core™ 2 Duo processors
●
T9300 2.50-GHz processor, 6-MB L2 cache, 800-MHz FSB
●
T8300 2.40-GHz processor, 3-MB L2 cache, 800-MHz FSB
●
T8100 2.10-GHz processor, 3-MB L2 cache, 800-MHz FSB
●
T7800 2.60-GHz processor, 4-MB L2 cache, 800-MHz FSB
●
T7700 2.40-GHz processor, 4-MB L2 cache, 800-MHz FSB
●
T7500 2.20-GHz processor, 4-MB L2 cache, 800-MHz FSB
●
T7300 2.00-GHz processor, 4-MB L2 cache, 800-MHz FSB
●
T7250 2.00-GHz processor, 2-MB L2 cache, 800-MHz FSB
●
T7100 1.80-GHz processor, 2-MB L2 cache, 800-MHz FSB
●
T5550 1.83-GHz processor, 2-MB L2 cache, 800-MHz FSB
●
T5470 1.60-GHz processor, 2-MB L2 cache, 800-MHz FSB
●
T5270 1.40-GHz processor, 2-MB L2 cache, 800-MHz FSB)
Intel Pentium® Dual Core processor:
●
T2310 1.83-GHz processor, 1-MB L2 cache, 533-MHz FSB
Intel Celeron® M processors
Chipset
●
550 2.00-GHz processor, 1-MB L2 cache, 533-MHz FSB
●
540 1.86-GHz processor, 1-MB L2 cache, 533-MHz FSB
●
530 1.73-GHz processor, 1-MB L2 cache, 533-MHz FSB
Northbridge: Intel PM965 with up to 800-MHz FSB
Southbridge: Intel ICH-8M
Graphics
ATI Mobility Radeon X1350 ATI-M62s graphics subsystem with up to 128-MB DDR1 or
128-MB DDR2 discrete graphics subsystem memory
Panel
All display assemblies include 2 wireless local area network (WLAN) antennae
●
17.0-inch WXGA BrightView
●
17.0-inch WXGA AntiGlare
1
Category
Description
Memory
2 customer-accessible/upgradable memory module slots
Support for dual-channel memory
Support for up to 4 GB of system RAM
PC2-5300, 667-MHz, DDR2
Support for the following configurations:
Hard drives
●
4096-MB total system memory (2048 × 2, dual-channel)
●
3072-MB total system memory (2048 + 1024)
●
2560-MB total system memory (2048 + 512)
●
2048-MB total system memory (1024 × 2, dual-channel)
●
2048-MB total system memory (2048 × 1)
●
1536-MB total system memory (1024 + 512)
●
1024-MB total system memory (512 × 2, dual-channel)
●
1024-MB total system memory (1024 × 1)
●
512-MB total system memory (512 × 1)
Support for 9.5-mm, 2.5-inch hard drives
Customer-accessible
Serial ATA
Support for the following drives:
●
250-GB, 5400-rpm
●
160-GB, 5400-rpm
●
120-GB, 5400-rpm
●
80-GB, 5400-rpm
HP 3D DriveGuard
Optical drives
Fixed (removal of 1 screw required)
Customer-accessible
Parallel ATA
12.7-mm tray load
Support for the following drives:
Diskette drive
●
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
●
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
●
Blu-ray Disc ROM and SuperMulti DVD±R/RW Double-Layer Drive
●
DVD/CD-RW Combo Drive
Supports external USB diskette drive only
Supports boot from external USB diskette drive
2
Chapter 1 Product description
Category
Description
Supports 3-mode diskette drive
Audio
HD audio - ADI1981
Single speaker
Modem
56K V.92 1.5-inch data/fax modem with digital line guard
Modem cable included in the Czech Republic, Europe, France, Greece, Hungary, Israel,
Poland, Russia, Saudi Arabia, Slovakia, Slovenia, South Africa, Turkey, and the United
Kingdom
Ethernet
Intel 82562GT
S3/S4/S5 wake-on-LAN: DC - no
S3/S4/S5 wake-on-LAN: AC - yes
Wireless
Integrated WLAN options by way of wireless module:
2 WLAN antennae built into display assembly
Support for no-WLAN option
Support for the following WLAN formats:
●
Intel 802.11a/b/g/n without iAMT
●
Broadcom 802.11a/b/g
●
Intel 802.11a/b/g without iAMT
●
Intel 802.11a/b/g (not available on computer models equipped with Intel Celeron M
processors)
●
Broadcom 802.11b/g
●
Intel 802.11b/g (not available on computer models equipped with Intel Celeron M
processors)
Integrated personal area network (PAN) options by way of Bluetooth® module:
Support for no-WPAN option
Broadcom Bluetooth 2.0+EDR
External media card
One ExpressCard/54 slot
SD/MMC Card Reader supporting Secure Digital (SD) Memory Card and MultiMediaCard
(MMC)
Ports
Audio-in (mono microphone)
Audio-out (stereo headphone)
RJ-11 (modem)
RJ-45 (Ethernet, includes link and activity lights)
USB (3)
VGA (Dsub 15-pin) supporting 1600 × 1200 external resolution at 75-GHz (hot plug/unplug
with auto-detect)
2-pin AC power
Keyboard/pointing devices
14.45-inch keyboard with separate numeric keypad
3
Category
Description
TouchPad only, with 2 TouchPad buttons and vertical scrolling (taps enabled as default)
Power requirements
90-W AC adapter with localized cable plug support (2-wire plug with ground pin, supports
2-pin DC connector)
6-cell, 55-Wh Li-ion battery
Security
Supports Kensington security lock
Operating system
Preinstalled:
Windows Vista® Basic 32 with Office Ready
Windows Vista Home Premium with Office Ready
Windows Vista Business 32 with Office Ready
Windows® XP Professional
FreeDOS
Restore media:
Windows Vista Basic 32
Windows Vista Home Premium
Windows Vista Business 32
Windows XP Professional
DRDVD Vista
Certified: Microsoft® WHQL
Serviceability
End-user replaceable parts:
AC adapter
Battery (system)
Hard drive
Memory module
Optical drive
WLAN module
4
Chapter 1 Product description
2
External component identification
Top components
TouchPad
Item
Component
Function
(1)
TouchPad*
Moves the pointer and selects or activates items on the
screen.
(2)
Left TouchPad button*
Functions like the left button on an external mouse.
(3)
Right TouchPad button*
Functions like the right button on an external mouse.
(4)
TouchPad scroll zone
Scrolls up or down.
*This table describes factory settings. View or change pointing device preferences as follows:
●
In Windows Vista, select Start > Control Panel > Hardware and Sound > Mouse.
●
In Windows XP, select Start > Control Panel > Printers and Other Hardware > Mouse.
Top components
5
Buttons, lights, and speaker
Item
Component
Function
(1)
Wireless button
Turns the wireless feature on or off, but does not establish
a wireless connection.
NOTE: A wireless network must be set up in order to
establish a wireless connection.
(2)
(3)
Wireless light
Power button
●
On: An integrated wireless device, such as a wireless
local area network (WLAN) device, the HP Broadband
Wireless Module, and/or a Bluetooth® device, is on.
●
Off: All wireless devices are off.
●
When the computer is off, press the button to turn on
the computer.
●
When the computer is on, press the button to initiate
Hibernation.
●
When the computer is in the Sleep state (Windows
Vista) or in Standby (Windows XP), press the button
briefly to exit the Sleep state or Standby.
●
When the computer is in Hibernation, press the button
briefly to exit Hibernation.
If the computer has stopped responding and Windows®
shutdown procedures are ineffective, press and hold the
power button for at least 5 seconds to turn off the computer.
To learn more about your power settings, follow these
steps:
6
Chapter 2 External component identification
●
In Windows Vista, select Start > Control Panel >
System and Maintenance > Power Options.
●
In Windows XP, select Start > Control Panel >
Performance and Maintenance > Power Options.
Item
Component
Function
(4)
Power light
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state (Windows
Vista) or Standby (Windows XP).
●
Off: The computer is off or in Hibernation.
(5)
Speaker
Produces sound.
Item
Component
Function
(1)
esc key
Displays system information when pressed in combination
with the fn key.
(2)
fn key
Executes frequently used system functions when pressed
in combination with a function key or the esc key.
(3)
Windows logo key
Displays the Windows Start menu.
(4)
Windows applications key
Displays a shortcut menu for items beneath the pointer.
(5)
Numeric keypad keys
Can be used like the keys on an external numeric keypad.
(6)
Function keys
Execute frequently used system functions when pressed
in combination with the fn key.
Keys
Top components
7
Front components
Item
Component
Function
(1)
Audio-out (headphone) jack
Produces sound when connected to optional powered
stereo speakers, headphones, ear buds, a headset, or
television audio.
(2)
Audio-in (microphone) jack
Connects an optional computer headset microphone,
stereo array microphone, or monaural microphone.
(3)
SD/MMC Card Reader
Supports the following optional digital card formats:
SD Memory Card and MMC.
Right-side components
Item
Component
Function
(1)
Optical drive
Reads optical discs and, on select models, also writes to
optical discs.
(2)
Optical drive light
Blinking: The optical drive is being accessed.
(3)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from being
mishandled or stolen.
8
Chapter 2 External component identification
Left-side components
Item
Component
Function
(1)
Battery light
●
Amber: A battery is charging.
●
Blue: A battery is close to full charge capacity.
●
Blinking amber: A battery that is the only available
power source has reached a low battery level. When
the battery reaches a critical battery level, the battery
light begins blinking rapidly.
●
If the computer is plugged into an external power
source, the light turns off when all batteries in the
computer are fully charged. If the computer is not
plugged into an external power source, the light stays
off until the battery reaches a low battery level.
(2)
ExpressCard slot
Supports optional ExpressCards.
(3)
RJ-11 (modem) jack
Connects a modem cable.
(4)
Vent
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(5)
External monitor port
Connects an external VGA monitor or projector.
(6)
Power connector
Connects an AC adapter.
(7)
RJ-45 (network) jack
Connects a network cable.
(8)
USB ports (3)
Connect optional USB devices.
Left-side components
9
Bottom components
Item
Component
Function
(1)
Battery bay
Holds the battery.
(2)
Battery release latches (2)
Release the battery from the battery bay.
(3)
Memory module compartment
Contains 2 memory module slots.
(4)
Vents (4)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(5)
Hard drive bay
Holds the hard drive.
(6)
WLAN module compartment (select models only)
Contains a WLAN module slot.
CAUTION: To prevent an unresponsive system, use only
a wireless module authorized for use in the computer by
the governmental agency that regulates wireless devices
in your country or region. If you install the module and then
receive a warning message, remove the module to restore
computer functionality, and then contact technical support
through Help and Support.
10
Chapter 2 External component identification
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model number
located on the bottom of the computer.
Serial number location
11
Computer major components
12
Chapter 3 Illustrated parts catalog
Item
Description
(1)
Display assemblies (include 2 wireless antenna transceivers and cables)
Spare part number
17.0-inch, WXGA with AntiGlare
456582-001
17.0-inch, WXGA with BrightView
456583-001
Display internal components:
Display enclosure (includes display bezel, 2 WLAN antenna transceivers and cables)
456586-001
Display hinges (includes left and right hinges)
456584-001
Display inverter
457621-001
(2)
Switch cover (includes button board and cable)
456581-001
(3)
Keyboards
(4)
For use in Belgium
456587-181
For use in the Czech Republic
456587-221
For use in Denmark
456587-081
For use in France
456587-051
For use in French Canada
456587-121
For use in Germany
456587-041
For use in Greece
456587-DJ1
For use in Hungary
456587-211
For use in Iceland
456587-DD1
For use in Israel
456587-BB1
For use in Italy
456587-061
For use in the Netherlands
456587-B31
For use in Norway
456587-091
For use in Portugal
456587-131
For use in Russia
456587-251
For use in Saudi Arabia
456587-171
For use in Slovakia
456587-231
For use in Slovenia
456587-BA1
For use in Spain
456587-071
For use in Sweden
456587-B71
For use in Switzerland
456587-BG1
For use in Turkey
456587-141
For use in the United Kingdom
456587-031
For use in the United States
456587-001
Speaker
457614-001
Computer major components
13
Item
Description
Spare part number
(5)
Top cover
457616-001
Plastics Kit (see Plastics Kit on page 18 for more Plastics Kit spare part information):
456614-001
(6a)
ExpressCard slot bezel
(6b)
WLAN module compartment cover (includes one captive screw, secured by a C-clip)
(6c)
Memory module compartment cover (includes one captive screw, secured by a C-clip)
(6d)
Hard drive bay cover (includes 2 captive screws, secured by C-clips)
TouchPad components
(7a)
TouchPad bracket (included in the Miscellaneous TouchPad Kit, which also includes the
TouchPad button board actuators, which are not illustrated)
457618-001
(7b)
TouchPad board (includes cable)
457617-001
(8)
TouchPad button board (includes cable)
456601-001
(9)
System boards (include replacement thermal material)
Includes 128-MB of DDR2 graphics subsystem memory
456613-001
Includes 64-MB of DDR2 graphics subsystem memory
456612-001
Includes 128-MB of DDR1 graphics subsystem memory
456611-001
Includes 64-MB of DDR1 graphics subsystem memory
456610-001
(10)
Battery connector board
457620-001
(11)
Optical drive connector board
456805-001
(12)
Fan
431312-001
(13)
Heat sink (includes replacement thermal material)
456606-001
(14)
Processors (includes replacement thermal material)
Intel Core 2 Duo processors:
14
●
T9300 2.50-GHz (6-MB L2 cache, 800-MHz FSB)
463050-001
●
T8300 2.40-GHz (3-MB L2 cache, 800-MHz FSB)
463049-001
●
T8100 2.10-GHz (3-MB L2 cache, 800-MHz FSB)
463048-001
●
T7800 2.60-GHz (4-MB L2 cache, 800-MHz FSB)
459465-001
●
T7700 2.40-GHz (4-MB L2 cache, 800-MHz FSB)
446894-001
●
T7500 2.20-GHz (4-MB L2 cache, 800-MHz FSB)
446893-001
●
T7300 2.00-GHz (4-MB L2 cache, 800-MHz FSB)
446892-001
●
T7250 2.00-GHz (2-MB L2 cache, 800-MHz FSB)
459463-001
●
T7100 1.80-GHz (2-MB L2 cache, 800-MHz FSB)
446891-001
●
T5550 1.83-GHz (2-MB L2 cache, 800-MHz FSB)
459464-001
●
T5470 1.60-GHz (2-MB L2 cache, 800-MHz FSB)
456575-001
●
T5270 1.40-GHz (2-MB L2 cache, 800-MHz FSB)
462345-001
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
Intel Pentium Dual Core processor:
●
462619-001
T2310 1.83-GHz (1-MB L2 cache, 533-MHz FSB)
Intel Celeron M processors:
●
550 2.00-GHz (1-MB L2 cache, 533-MHz FSB)
446888-001
●
540 1.86-GHz (1-MB L2 cache, 533-MHz FSB)
446889-001
●
530 1.73-GHz (1-MB L2 cache, 533-MHz FSB)
459462-001
(15)
RTC battery
449137-001
(16)
Modem module
441074-001
NOTE: The modem module spare part kit does not include a modem module cable. The
modem module cable is included in the Cable Kit, spare part number 457615-001. See Cable
Kit on page 19 for more Cable Kit spare part number information.
(17)
Broadcom Bluetooth module (does not include Bluetooth module cable)
398393-002
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The
Bluetooth module cable is included in the Cable Kit, spare part number 457615-001. See
Cable Kit on page 19 for more Cable Kit spare part number information.
(18)
Base enclosure (includes rubber feet)
457619-001
Rubber Kit (not illustrated, contains 6 computer feet and 8 display bezel screw covers)
456616-001
(19)
6-cell, 55-Wh Li-ion battery
456865-001
(20)
WLAN modules
Intel 802.11a/b/g/n WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay,
the United States, Venezuela, and Vietnam
441086-001
●
For use in Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
441086-002
Broadcom 802.11a/b/g WLAN modules:
●
For use in Canada, Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and
the United States
441075-001
Computer major components
15
Item
Description
Spare part number
●
441075-002
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican
Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the
Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia,
Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands,
New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of
Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi
Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri
Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland,
Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago,
Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the
United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire,
Zambia, and Zimbabwe
Intel 802.11a/b/g WLAN modules:
For use with computer models equipped with Intel Core Duo 2 and Intel Celeron M processors:
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the
United States, Uruguay, Venezuela, and Vietnam
441082-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
441082-002
For use only with computer models equipped with Intel Core Duo 2 processors:
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda,
Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican
Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India,
Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the
United States, Uruguay, Venezuela, and Vietnam
448674-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the
Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece,
Hungary, Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania,
Luxembourg, Malta, Monaco, the Netherlands, Norway, Oman, the Philippines, Poland,
Portugal, Qatar, Romania, Russia, Serbia and Montenegro, Singapore, Slovakia,
Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey, Ukraine, the
United Kingdom, and Uzbekistan
448674-002
Broadcom 802.11b/g WLAN modules:
16
Chapter 3 Illustrated parts catalog
Item
(21)
(22)
(23)
Description
Spare part number
●
For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and
the United States
441090-001
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia &
Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso,
Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,
Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El
Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French
Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong,
Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory Coast, Jamaica,
Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar,
Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the
People's Republic of China, Peru, the Philippines, Poland, Portugal, Qatar, the Republic
of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe,
Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South
Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, Togo, Tonga,
Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United
Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela,
Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
441090-002
Memory modules (PC2-5300, 667-MHz, DDR2)
2048-MB
417506-001
1024-MB
414046-001
512-MB
414045-001
Hard drives (include hard drive bracket)
250-GB, 5400-rpm
457613-001
160-GB, 5400-rpm
457014-001
120-GB, 5400-rpm
457013-001
80-GB, 5400-rpm
457012-001
Optical drives (include bezel and bracket)
DVD±RW and CD-RW Double-Layer Combo Drive with LightScribe
456799-001
DVD±RW and CD-RW Double-Layer Combo Drive
456798-001
Blu-ray Disc ROM and SuperMulti DVD±R/RW Double-Layer Drive
456580-001
DVD/CD-RW Combo Drive
456797-001
Cable Kit (not illustrated; see Cable Kit on page 19 for more Cable Kit spare part number
information)
456594-001
Computer major components
17
Plastics Kit
Item
18
Description
Spare part number
Plastics Kit:
456614-001
(1)
Hard drive bay cover (includes 2 captive screws, secured by C-clips)
(2)
WLAN module compartment cover (includes one captive screw, secured by a C-clip)
(3)
ExpressCard slot bezel
(4)
Memory module compartment cover (includes one captive screw, secured by a C-clip)
Chapter 3 Illustrated parts catalog
Cable Kit
Item
Description
Spare part number
Cable Kit:
457615-001
(1)
RJ-11 jack cable
(2)
Display lid switch module and cable
(3)
Bluetooth module cable
Cable Kit
19
Mass storage devices
Item
Description
(1)
Optical drives (include bezel and bracket)
(2)
20
Spare part number
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
456799-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
456798-001
Blu-ray Disc ROM and SuperMulti DVD±R/RW Double-Layer Drive
456580-001
DVD/CD-RW Combo Drive
456797-001
Hard drives (include bracket)
250-GB, 5400-rpm
457613-001
160-GB, 5400-rpm
457014-001
120-GB, 5400-rpm
457013-001
80-GB, 5400-rpm
457012-001
Chapter 3 Illustrated parts catalog
Miscellaneous parts
Description
Spare part number
90-W AC adapter
458220-001
Logo Kit
456617-001
Nylon carrying case
325814-001
USB 1.1 diskette drive
359118-001
Power cords:
For use in Australia
342714-011
For use in Denmark
342714-081
For use in Europe, the Middle East, and Africa
342714-021
For use in Israel
342714-BB1
For use in Italy
342714-061
For use in Switzerland
342714-AG1
For use in the United Kingdom
342714-031
For use the United States
342714-001
Screw Kit
456615-001
●
Phillips PM3.0×4.0 screw
●
Phillips PM2.5×130 captive screw
●
Phillips PM2.5×10.0 captive screw
●
Phillips PM2.5×7.0 captive screw
●
Phillips PM2.5×7.0 screw
●
Phillips PM2.5×4.0 screw
●
Phillips PM2.0×8.0 screw
●
Phillips PM2.0×6.0 screw
●
Phillips PM2.0×5.0 captive screw
●
Phillips PM2.0×4.0 screw
●
Phillips PM2.0×2.0 broad-head screw
●
Torx T8M2.5×9.0 screw
●
Torx T8M2.5×7.0 screw
●
Torx T8M2.5×6.0 screw
●
Torx T8M2.5×4.0 screw
●
Torx T8M2.5×3.0 broad-head screw
Miscellaneous parts
21
Sequential part number listing
Spare part
number
Description
325814-001
Nylon carrying case
342714-001
Power cord for use in the United States
342714-011
Power cord for use in Australia and New Zealand
342714-021
Power cord for use in Europe, the Middle East, Africa
342714-031
Power cord for use in the United Kingdom
342714-061
Power cord for use in Italy
342714-081
Power cord for use in Denmark
342714-AG1
Power cord for use in Switzerland
342714-BB1
Power cord for use in Israel
359118-001
USB 1.1 diskette drive
398393-002
Bluetooth module for use in North America
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 457615-001. See Cable Kit on page 19 for more
Cable Kit spare part number information.
414045-001
512-MB memory module (PC2-5300, 667-MHz, DDR2)
414046-001
1024-MB memory module (PC2-5300, 667-MHz, DDR2)
417506-001
2048-MB memory module (PC2-5300, 667-MHz, DDR2)
431312-001
Fan
441074-001
Modem module (includes modem module cable)
NOTE: The modem module spare part kit does not include a modem module cable. The modem module
cable is included in the Cable Kit, spare part number 457615-001. See Cable Kit on page 19 for more Cable
Kit spare part number information.
441075-001
22
Broadcom 802.11a/b/g WLAN module for use in Canada, Cayman Islands, Guam, Puerto Rico, the U.S. Virgin
Islands, and the United States
Chapter 3 Illustrated parts catalog
Spare part
number
Description
441075-002
Broadcom 802.11a/b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central
African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,
Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory
Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta,
the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the
Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao
Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts &
Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan,
Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the
United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
441082-001
Intel 802.11a/b/g WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
441082-002
Intel 802.11a/b/g WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the
Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and
Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey,
Ukraine, the United Kingdom, and Uzbekistan
441086-001
Intel 802.11a/b/g/n WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
441086-002
Intel 802.11a/b/g/n WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the
Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and
Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey,
Ukraine, the United Kingdom, and Uzbekistan
441090-001
Broadcom 802.11b/g WLAN module for use in Canada, Cayman Islands, Guam, Puerto Rico, the U.S. Virgin
Islands, and the United States
Sequential part number listing
23
24
Spare part
number
Description
441090-002
Broadcom 802.11b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh,
Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central
African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,
Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea,
Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory
Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta,
the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the
Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao
Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore,
Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts &
Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan,
Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the
United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen,
Zaire, Zambia, and Zimbabwe
446888-001
Intel Celeron M 550 1.86-GHz processor (1-MB L2 cache, 533-MHz FSB, includes replacement thermal
material)
446889-001
Intel Celeron M 540 2.00-GHz processor (1-MB L2 cache, 533-MHz FSB, includes replacement thermal
material)
446891-001
Intel Core 2 Duo T7100 1.80-GHz processor (2-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
446892-001
Intel Core 2 Duo T7300 2.00-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
446893-001
Intel Core 2 Duo T7500 2.20-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
446894-001
Intel Core 2 Duo T7700 2.40-GHz processor (4-MB L2 cache, 800-MHz FSB, includes replacement thermal
material)
448674-001
Intel 802.11a/b/g WLAN module for use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados,
Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic,
Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico,
Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay, Venezuela, and Vietnam
448674-002
Intel 802.11a/b/g WLAN module for use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia,
Cyprus, the Czech Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta, Monaco, the
Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania, Russia, Serbia and
Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka, Sweden, Switzerland, Turkey,
Ukraine, the United Kingdom, and Uzbekistan
456575-001
Intel Core 2 Duo 5470 1.60-GHz processor (2-MB L2 cache, 800-MHz FSB)
456580-001
Blu-ray Disc ROM and SuperMulti DVD±R/RW Double-Layer Drive
456581-001
Switch cover (includes button board and cable)
456582-001
17.0-inch WXGA display assembly with AntiGlare (includes 2 wireless antenna transceivers and cables)
456583-001
17.0-inch WXGA display assembly with BrightView (includes 2 wireless antenna transceivers and cables)
456584-001
Display hinges (includes left and right hinges)
Chapter 3 Illustrated parts catalog
Spare part
number
Description
456586-001
Display enclosure (includes display bezel, 2 wireless antenna transceivers and cables)
456587-001
Keyboard for use in the United States
456587-031
Keyboard for use in the United Kingdom
456587-041
Keyboard for use in Germany
456587-051
Keyboard for use in France
456587-061
Keyboard for use in Italy
456587-071
Keyboard for use in Spain
456587-081
Keyboard for use in Denmark
456587-091
Keyboard for use in Norway
456587-121
Keyboard for use in French Canada
456587-131
Keyboard for use in Portugal
456587-141
Keyboard for use in Turkey
456587-171
Keyboard for use in Saudi Arabia
456587-181
Keyboard for use in Belgium
456587-211
Keyboard for use in Hungary
456587-221
Keyboard for use in the Czech Republic
456587-231
Keyboard for use in Slovakia
456587-251
Keyboard for use in Russia
456587-B31
Keyboard for use in the Netherlands
456587-B71
Keyboard for use in Sweden and Finland
456587-BA1
Keyboard for use in Slovenia
456587-BB1
Keyboard for use in Israel
456587-BG1
Keyboard for use in Switzerland
456587-DD1
Keyboard for use in Iceland
456587-DJ1
Keyboard for use in Greece
456601-001
TouchPad button board (includes cable)
456606-001
Heat sink (includes replacement thermal material)
456610-001
System board with 64-MB DDR1 graphics subsystem memory (includes replacement thermal material)
456611-001
System board with 128-MB DDR1 graphics subsystem memory (includes replacement thermal material)
456612-001
System board with 64-MB DDR2 graphics subsystem memory (includes replacement thermal material)
456613-001
System board with 128-MB DDR2 graphics subsystem memory (includes replacement thermal material)
456614-001
Plastics Kit (see Plastics Kit on page 18 for more Plastics Kit spare part information)
456615-001
Screw Kit
Sequential part number listing
25
26
Spare part
number
Description
456616-001
Rubber Kit (contains 6 computer feet and 8 display bezel screw covers)
456617-001
Logo Kit
456797-001
DVD/CD-RW Combo Drive (includes bezel and bracket)
456798-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe (includes bezel and
bracket)
456799-001
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive (includes bezel and bracket)
456805-001
Optical drive connector board
456865-001
6-cell, 55-Wh Li-ion battery
457012-001
80-GB, 5400-rpm hard drive (includes bracket)
457013-001
120-GB, 5400-rpm hard drive (includes bracket)
457014-001
160-GB, 5400-rpm hard drive (includes bracket)
457613-001
250-GB, 5400-rpm hard drive (includes bracket)
457614-001
Speaker
457615-001
Cable Kit (see Cable Kit on page 19 for more Cable Kit spare part information)
457616-001
Top cover
457617-001
TouchPad board (includes cable)
457618-001
TouchPad Miscellaneous Kit (includes TouchPad bracket and TouchPad button board actuators)
457619-001
Base enclosure (includes 6 rubber feet)
457620-001
Battery connector board
457621-001
Display inverter
458220-001
90-W AC adapter
459462-001
Intel Celeron 530 1.73-GHz processor (1-MB L2 cache, 533-MHz FSB)
459463-001
Intel Core 2 Duo T7250 2.00-GHz processor (2-MB L2 cache, 800-MHz FSB)
459464-001
Intel Core 2 Duo T5550 1.83-GHz processor (2-MB L2 cache, 800-MHz FSB)
459465-001
Intel Core 2 Duo T7800 2.60-GHz processor (4-MB L2 cache, 800-MHz FSB)
459724-001
Optical drive board
462345-001
intel Core 2 Duo T5270 1.40-GHz processor (2-MB L2 cache, 800-MHz FSB)
462619-001
Intel Pentium Dual Core T2310 1.83-GHz processor (1-MB L2 cache, 533-MHz FSB)
463048-001
Intel Core 2 Duo T8100 processor (2.10-GHz, 3-MB L2 cache, 800-MHz FSB)
463049-001
Intel Core 2 Duo T8300 processor (2.40-GHz, 3-MB L2 cache, 800-MHz FSB)
463050-001
Intel Core 2 Duo T9300 processor (2.50-GHz, 6-MB L2 cache, 800-MHz FSB)
Chapter 3 Illustrated parts catalog
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Flat-bladed screwdriver
●
Magnetic screwdriver
●
Phillips P0 and P1 screwdrivers
●
Torx T8 screwdriver
Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Preliminary replacement requirements
27
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme
care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the
computer is off or in Hibernation, turn the computer on, and then shut it down through the operating
system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and
be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
28
Chapter 4 Removal and replacement procedures
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you area ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described
in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION:
A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Preliminary replacement requirements
29
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive
foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials are
selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
30
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Chapter 4 Removal and replacement procedures
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive strips must
be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Preliminary replacement requirements
31
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the
password:
NOTE:
These steps also clear CMOS.
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the real-time clock (RTC) battery (see RTC battery on page 73).
6.
Wait approximately 5 minutes.
7.
Replace the RTC battery and reassemble the computer.
8.
Connect AC power to the computer. Do not reinsert any batteries at this time.
9.
Turn on the computer.
All passwords and all CMOS settings have been cleared.
32
Chapter 4 Removal and replacement procedures
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 93 screws, in 17 different sizes, that must be removed, replaced, or loosened
when servicing the computer. Make special note of each screw size and location during removal and
replacement.
Serial number
Report the computer serial number to HP when requesting information or ordering spare parts. The
serial number is located on the bottom of the computer.
Component replacement procedures
33
Computer feet
The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare
part number 456616-001. There are 6 rubber feet that attach to the base enclosure in the locations
illustrated below.
34
Chapter 4 Removal and replacement procedures
Battery
Description
Spare part number
6-cell, 55-Wh Li-ion battery
456865-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the battery:
1.
Turn the computer upside down on a flat surface, with the battery bay toward you.
2.
Slide the battery release latches (1) to release the battery.
3.
Remove the battery (2) from the computer.
Install the battery by inserting it into the battery bay until you hear a click.
Component replacement procedures
35
Hard drive
NOTE:
All hard drive spare part kits include a hard drive bracket.
Description
Spare part number
250-GB, 5400-rpm hard drive
457613-001
160-GB, 5400-rpm hard drive
457014-001
120-GB, 5400-rpm hard drive
457013-001
80-GB, 5400-rpm hard drive
457012-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
Remove the hard drive:
36
1.
Position the computer with the front toward you.
2.
Loosen the two Phillips PM2.0×5.0 captive screws (1) that secure the hard drive bay cover to the
computer.
3.
Lift the right side of the hard drive bay cover (2), swing it to left, and remove the cover. The hard
drive bay cover is included in the Plastics Kit, spare part number 456614-001.
4.
Loosen the Phillips PM2.5×13.0 captive screw (1) that secures the hard drive to the computer.
Chapter 4 Removal and replacement procedures
5.
Grasp the Mylar tab (2) on the hard drive and slide the hard drive (3) to the left to disconnect it from
the system board.
6.
Remove the hard drive (4) from the hard drive bay.
7.
If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive
bracket screws (1) from each side of the hard drive.
8.
Lift the bracket (2) straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
Component replacement procedures
37
WLAN module
Description
Spare part number
Intel 802.11a/b/g/n WLAN modules:
●
For use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States,
Venezuela, and Vietnam
441086-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
441086-002
Broadcom 802.11a/b/g WLAN modules:
●
For use in Canada, Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United
States
441075-001
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of
China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El
Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana,
Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe,
Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland,
India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati,
Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,
Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New
Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New
Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania,
Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia
and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St.
Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine,
the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela,
Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
441075-002
Intel 802.11a/b/g WLAN modules:
For use with computer models equipped with Intel Core Duo 2 and Intel Celeron M processors:
38
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay,
Venezuela, and Vietnam
441082-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
441082-002
Chapter 4 Removal and replacement procedures
Description
Spare part number
For use only with computer models equipped with Intel Core Duo 2 processors:
●
For use in Antigua & Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei,
Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador,
El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia,
Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, the United States, Uruguay,
Venezuela, and Vietnam
448674-001
●
For use in Austria, Azerbaijan, Bahrain, Belgium, Brazil, Bulgaria, Croatia, Cyprus, the Czech
Republic, Denmark, Egypt, Estonia, Finland, France, Georgia, Germany, Greece, Hungary,
Iceland, Ireland, Israel, Italy, Latvia, Lebanon, Liechtenstein, Lithuania, Luxembourg, Malta,
Monaco, the Netherlands, Norway, Oman, the Philippines, Poland, Portugal, Qatar, Romania,
Russia, Serbia and Montenegro, Singapore, Slovakia, Slovenia, South Africa, Spain, Sri Lanka,
Sweden, Switzerland, Turkey, Ukraine, the United Kingdom, and Uzbekistan
448674-002
Broadcom 802.11b/g WLAN modules:
●
For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the
United States
●
441090-002
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia & Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia,
Cameroon, Cape Verde, the Central African Republic, Chad, Chile, Colombia, Comoros, the
Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the
Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana,
Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, the Ivory
Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar,
Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger,
Nigeria, Norway, Oman, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic
of China, Peru, the Philippines, Poland, Portugal, Qatar, the Republic of Moldova, Romania,
Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia
and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St.
Vincent & Grenada, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania,
Thailand, Togo, Tonga, Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda,
Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
441090-001
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless
module authorized for use in the computer by the governmental agency that regulates wireless devices
in your country or region. If you replace the module and then receive a warning message, remove the
module to restore computer functionality, and then contact technical support through Help and Support.
Before removing the WLAN module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
Component replacement procedures
39
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
Remove the WLAN module:
1.
Position the computer with the front toward you.
2.
Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the WLAN module compartment
cover to the computer.
3.
Lift the right side of the WLAN module compartment cover (2), swing it to left, and remove the
cover. The WLAN module compartment cover is included in the Plastics Kit, spare part number
456614-001.
4.
Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The black WLAN antenna cable is connected to the WLAN module “Main” terminal. The
white WLAN antenna cable is connected to the WLAN module “Aux” terminal.
5.
40
Remove the two Phillips PM2.5×4.0 screws (2) that secure the WLAN module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
Chapter 4 Removal and replacement procedures
6.
Remove the WLAN module (3) by pulling the module away from the slot at an angle.
NOTE:
WLAN modules are designed with a notch (4) to prevent incorrect installation.
Reverse this procedure to install the WLAN module.
Memory module
Description
Spare part number
2048-MB (PC2-5300, 667-MHz, DDR2)
417506-001
1024-MB (PC2-5300, 667-MHz, DDR2)
414046-001
512-MB (PC2-5300, 667-MHz, DDR2)
414045-001
Before removing the memory module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
Remove the memory module:
1.
Loosen the Phillips PM2.0×5.0 captive screw (1) that secures the memory module compartment
cover to the computer.
Component replacement procedures
41
2.
Lift the rear edge of the cover (2), swing it up and forward, and remove the cover. The memory
module compartment cover is included in the Plastics Kit, spare part number 456614-001.
3.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
4.
Remove the memory module (2) by pulling the module away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect installation into the
memory module slot.
Reverse this procedure to install a memory module.
Optical drive
NOTE:
42
All optical drive spare part kits include an optical drive bezel.
Description
Spare part number
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
456799-001
Chapter 4 Removal and replacement procedures
Description
Spare part number
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
456798-001
Blu-ray Disc ROM and SuperMulti DVD±R/RW Double-Layer Drive
456580-001
DVD/CD-RW Combo Drive
456797-001
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
Remove the optical drive:
1.
Position the computer with the right side toward you.
2.
Remove the Torx T8M2.5×7.0 screw (1) that secures the optical drive to the computer.
3.
Insert a flat-bladed screwdriver or similar tool into the optical drive tab access (2) and press the
tab to the left to release the optical drive from the computer.
4.
Remove the optical drive (3) from the computer.
5.
If it is necessary to replace the optical drive bracket, position the optical drive with the rear toward
you.
6.
Remove the two Phillips PM2.0×4.0 screws (1) that secure the optical drive bracket to the optical
drive.
Component replacement procedures
43
7.
Remove the optical drive bracket (2).
Reverse this procedure to reassemble and install an optical drive.
44
Chapter 4 Removal and replacement procedures
Switch cover and keyboard
Description
Spare part number
Switch cover (includes button board and cable)
456581-001
Keyboards for use in the following countries or regions:
Belgium
456587-181
Norway
456587-091
The Czech Republic
456587-221
Portugal
456587-131
Denmark
456587-081
Russia
456587-251
France
456587-051
Saudi Arabia
456587-171
French Canada
456587-121
Slovakia
456587-231
Germany
456587-041
Slovenia
456587-BA1
Greece
456587-DJ1
Spain
456587-071
Hungary
456587-211
Sweden and Finland
456587-B71
Iceland
456587-DD1
Switzerland
456587-BG1
Israel
456587-BB1
Turkey
456587-141
Italy
456587-061
The United Kingdom
456587-031
The Netherlands
456587-B31
The United States
456587-001
Before removing the switch cover and keyboard, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
Component replacement procedures
45
Remove the switch cover and keyboard:
1.
Remove the following screws:
(1) Two Torx T8M2.5×9.0 screws
(2) Two Torx T8M2.5×7.0 screws
(3) Three Torx T8M2.5×3.0 broad-head screws
46
2.
Remove the two Torx T8M2.5×7.0 screws that secure the keyboard to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
Chapter 4 Removal and replacement procedures
5.
Lift the switch cover (1) straight up until it disengages from the computer, and slide it back (2) until
it rests on the display assembly.
6.
Lift the rear edge of the keyboard (1) until it rests at an angle, and slide it back (2) until it rests on
the display assembly and switch cover.
Component replacement procedures
47
7.
Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and
disconnect the keyboard cable (2) from the system board.
8.
Remove the keyboard.
9.
Release the ZIF connector (1) to which the button board cable is attached, and disconnect the
button board cable (2) from the system board.
10. Remove the switch cover.
Reverse this procedure to install the switch cover and keyboard.
48
Chapter 4 Removal and replacement procedures
Speaker
Description
Spare part number
Speaker
457614-001
Before removing the speaker, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 45).
Remove the speaker:
1.
Disconnect the speaker cable (1) from the system board.
2.
Remove the two Torx T8M2.5×4.0 screws (2) that secure the speaker to the top cover.
3.
Remove the speaker (3) from the top cover.
Reverse this procedure to install the speaker.
Component replacement procedures
49
Display lid switch module
NOTE: The display lid switch module is included in the Cable Kit, spare part number Cable Kit, spare
part number 457615-001.
Before removing the display lid switch module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the switch cover and keyboard (see Switch cover and keyboard on page 45).
Remove the display lid switch module:
1.
Disconnect the display lid switch module cable (1) from the system board.
2.
Remove the display lid switch module (2) from the clip built into the top cover.
3.
Remove the display lid switch module cable from the clips (3) built into the top cover.
Reverse this procedure to install the display lid switch module.
50
Chapter 4 Removal and replacement procedures
Display assembly
NOTE:
All display assembly spare part kits include 2 WLAN antenna transceivers and cables.
Description
Spare part number
17.0-inch, WXGA with AntiGlare
456582-001
17.0-inch, WXGA with BrightView
456583-001
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 38).
6.
Remove the following components:
a.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
b.
Speaker (see Speaker on page 49)
c.
Display lid switch module (see Display lid switch module on page 50)
Remove the display assembly:
1.
Disconnect the display panel cables (1) and (2) from the system board.
2.
Remove the wireless antenna cables (3) from the clips and routing channels built into the top cover.
3.
Remove the four Torx T8M2.5×7.0 screws (1) that secure the display assembly to the computer.
Component replacement procedures
51
52
4.
Lift the display assembly (2) straight up and remove it.
5.
If it is necessary to replace the display bezel, display inverter, or display hinges, remove the eight
rubber screw covers (1) and the eight Torx T8M2.5×6.0 screws (2) that secure the display bezel
to the display assembly. The rubber screw covers are available in the Rubber Kit, spare part number
456616-001.
6.
Flex the inside edges of the left and right sides (1) and the top and bottom sides (2) of the display
bezel until the bezel disengages from the display enclosure.
Chapter 4 Removal and replacement procedures
7.
Remove the display bezel (3). The display bezel is available in the display enclosure kit using spare
part number 456586-001.
8.
If it is necessary to replace the display inverter, remove the inverter (1) from the display enclosure
as far as the display panel cable and the backlight cable will allow.
9.
Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter.
10. Remove the display inverter. The display inverter is available using spare part number
457621-001.
11. If it is necessary to replace the display hinges, remove the four Torx T8M2.5×6.0 screws (1) that
secure the display panel to the display enclosure.
Component replacement procedures
53
12. Remove the display panel (2).
13. Remove the four Phillips PM2.0×4.0 screws (1) that secure each display hinge to the display
panel.
14. Remove the display hinges (2). The left and right display hinges are available using spare part
number 456584-001.
Reverse this procedure to reassemble and install the display assembly.
54
Chapter 4 Removal and replacement procedures
Top cover
Description
Spare part number
Top cover
457616-001
Before removing the top cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
f.
Display assembly (see Display assembly on page 51)
Remove the top cover:
1.
Turn the computer upside down, with the front toward you.
2.
Remove the followng screws:
(1) Three Phillips PM2.0×2.0 broad-head screws
(2) Nine Torx T8M2.5×7.0 screws
(3) One Torx T8m2.5×4.0 screw
Component replacement procedures
55
56
3.
Turn the computer right-side up, with the left side toward you.
4.
Press in on the ExpressCard slot eject button (1) two times. The first press releases the
ExpressCard slot eject button. The second press releases the ExpressCard slot bezel from the
ExpressCard slot.
5.
Remove the ExpressCard slot bezel (2).
6.
Remove the three Torx T8M2.5×7.0 screws (3) that secure the top cover to the computer.
7.
Lift the rear edge of the top cover (1) and swing it up and forward until it rests at an angle.
8.
Lift the front edge of the top cover (2) until it disengages from the base enclosure.
9.
Tilt the top cover (3) back until the TouchPad cable is accessible.
Chapter 4 Removal and replacement procedures
10. Release the ZIF connector (4) to which the TouchPad cable is connected and disconnect the
TouchPad cable from the system board.
11. Remove the top cover.
Reverse this procedure to install the top cover.
Component replacement procedures
57
TouchPad board and TouchPad button board
Description
Spare part number
TouchPad board (includes cable)
457617-001
TouchPad button board (includes cable)
456601-001
TouchPad Miscellaneous Kit (includes TouchPad bracket and TouchPad button board actuators)
457618-001
Before removing the TouchPad board and TouchPad button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
f.
Display assembly (see Display assembly on page 51)
g.
Top cover (see Top cover on page 55)
Remove the TouchPad board and TouchPad button board:
58
1.
Turn the top cover upside down, with the front toward you.
2.
Release the ZIF connectors on the TouchPad button board (1) and TouchPad board (2) to which
the TouchPad board cable is connected.
3.
Disconnect and remove the TouchPad board cable (3).
Chapter 4 Removal and replacement procedures
4.
Remove the two Phillips PM2.0×4.0 screws (4) that secure the TouchPad bracket to the computer.
5.
Release the TouchPad bracket (1) by sliding it back.
6.
Remove the TouchPad bracket (2) by lifting it straight up.
7.
Remove the TouchPad button board (3).
8.
Remove the TouchPad button board cable (4) from the opening in the TouchPad bracket.
Component replacement procedures
59
9.
Remove the TouchPad board (1) from the top cover.
NOTE: When replacing the TouchPad board and TouchPad button board, be sure the TouchPad
button actuators (2) are installed in the top cover.
Reverse this procedure to install the TouchPad board and TouchPad button board.
Bluetooth module
NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth
module cable is included in the Cable Kit, spare part number 457615-001.
Description
Spare part number
Bluetooth module
398393-002
Before removing the Bluetooth module, follow these steps:
60
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
Chapter 4 Removal and replacement procedures
f.
Display assembly (see Display assembly on page 51)
g.
Top cover (see Top cover on page 55)
Remove the Bluetooth module:
1.
Disconnect the Bluetooth module cable (1) from the system board.
2.
Remove the two Phillips PM2.0×4.0 screws (2) that secure the Bluetooth module to the base
enclosure.
3.
Remove the Bluetooth module (3) from the base enclosure.
Reverse this procedure to install the Bluetooth module.
System board
NOTE:
All system board spare part kits include replacement thermal material.
Description
Spare part number
Includes 128 MB of DDR2 graphics subsystem memory
456613-001
Includes 64 MB of DDR2 graphics subsystem memory
456612-001
Includes 128 MB of DDR1 graphics subsystem memory
456611-001
Includes 64 MB of DDR1 graphics subsystem memory
456610-001
Before removing the system board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Component replacement procedures
61
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
f.
Display assembly (see Display assembly on page 51)
g.
Top cover (see Top cover on page 55)
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
Memory module (see Memory module on page 41)
●
WLAN module (see WLAN module on page 38)
●
Processor (see Processor on page 69)
Remove the system board:
62
1.
Remove the RJ-11 jack (1) from the clip built into the base enclosure and remove the RJ-11 jack
cable from the hook (2) built into the base enclosure.
2.
Disconnect the fan cable (3) and the Bluetooth module cable (4) from the system board.
Chapter 4 Removal and replacement procedures
3.
Remove the following screws:
(1) One Torx T8M2.5×6.0 screw that secures the system board to the base enclosure
(2) Three Torx T8M2.5×6.0 screws that secure the battery connector board to the base enclosure
(3) Four Torx T8M2.5×4.0 screws that secure the optical drive connector board to the base
enclosure
(4) One Phillips PMM2.0×6.0 screw that secures the system board to the base enclosure
4.
Flex the left side of the base enclosure (1) until the external monitor connector (2) is clear of the
opening in the base enclosure.
5.
Lift the rear edge of the system board (3) until it rests at an angle.
6.
Remove the system board (4) from the base enclosure by sliding it back.
Component replacement procedures
63
7.
If it is necessary to replace the battery connector board (1) and the optical drive connector board
(2), remove them from the connectors on the system board. The battery connector board is
available using spare part number 457620-001. The optical drive connector board is available using
spare part number 456805-001.
Reverse the preceding procedure to install the system board.
64
Chapter 4 Removal and replacement procedures
Fan
Description
Spare part number
Fan
456604-001
Before removing the fan, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
f.
Display assembly (see Display assembly on page 51)
g.
Top cover (see Top cover on page 55)
h.
System board (see System board on page 61)
Remove the fan:
1.
Remove the Phillips PM2.5×7.0 screw (1) that secures the fan to the base enclosure.
2.
Loosen the Phillips PM2.5×7.0 screw (2) that secures the fan to the base enclosure.
Component replacement procedures
65
3.
Remove the fan (3) from the base enclosure.
Reverse this procedure to install the fan.
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the left side
of the computer.
The computer uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is
designed to turn on automatically when high temperature conditions exist. These conditions are affected
by high external temperatures, system power consumption, power management/battery conservation
configurations, battery fast charging, and software requirements. Exhaust air is displaced through the
ventilation grill located on the left side of the computer.
66
Chapter 4 Removal and replacement procedures
Heat sink
Description
Spare part number
Heat sink (includes replacement thermal material)
456606-001
Before removing the heat sink, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
f.
Display assembly (see Display assembly on page 51)
g.
Top cover (see Top cover on page 55)
h.
System board (see System board on page 61)
Remove the heat sink:
1.
Turn the system board upside down, with the USB connectors toward you.
2.
In the 1, 2, 3, 4, 5, 6 sequence stamped into the heat sink, loosen the six Phillips PM2.5×10.0
screws (1) that secure the heat sink to the system board.
Component replacement procedures
67
3.
Remove the heat sink (2).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink (1), (2),
and (3) and the processor (4), Northbridge chip (5), and graphics subsystem memory (6) each time the
heat sink is removed. Thermal material is included with all heat sink, system board, and processor spare
part kits.
Reverse this procedure to install the heat sink.
68
Chapter 4 Removal and replacement procedures
Processor
NOTE:
All processor spare part kits include replacement thermal material.
Description
Spare part number
Intel Core 2 Duo processors:
●
T9300 2.50-GHz processor (6-MB L2 cache, 800-MHz FSB)
463050-001
●
T8300 2.40-GHz processor (3-MB L2 cache, 800-MHz FSB)
463049-001
●
T8100 2.10-GHz processor (3-MB L2 cache, 800-MHz FSB)
463048-001
●
T7800 2.60-GHz processor (4-MB L2 cache, 800-MHz FSB)
459465-001
●
T7700 2.40-GHz processor (4-MB L2 cache, 800-MHz FSB)
446894-001
●
T7500 2.20-GHz processor (4-MB L2 cache, 800-MHz FSB)
446893-001
●
T7300 2.00-GHz processor (4-MB L2 cache, 800-MHz FSB)
446892-001
●
T7250 2.00-GHz processor (2-MB L2 cache, 800-MHz FSB)
459463-001
●
T7100 1.80-GHz processor (2-MB L2 cache, 800-MHz FSB)
446891-001
●
T5550 1.83-GHz processor (2-MB L2 cache, 800-MHz FSB)
459464-001
●
T5470 1.60-GHz processor (2-MB L2 cache, 800-MHz FSB)
456575-001
●
T5270 1.40-GHz processor (2-MB L2 cache, 800-MHz FSB)
462345-001
Intel Pentium Dual Core processor:
●
462619-001
T2310 1.83-GHz processor (1-MB L2 cache, 533-MHz FSB)
Intel Celeron M processors:
●
550 2.00-GHz processor (1-MB L2 cache, 533-MHz FSB)
446889-001
●
540 1.86-GHz processor (1-MB L2 cache, 533-MHz FSB)
446888-001
●
530 1.73-GHz processor (1-MB L2 cache, 533-MHz FSB)
459462-001
Before removing the processor, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
Component replacement procedures
69
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
f.
Display assembly (see Display assembly on page 51)
g.
Top cover (see Top cover on page 55)
h.
System board (see System board on page 61)
Remove the processor:
1.
Turn the system board upside down, with the USB connectors toward you.
2.
Use a flat-bladed screwdriver to turn the processor locking screw (1) one-half turn counterclockwise
until you hear a click.
3.
Lift the processor (2) straight up and remove it.
NOTE: When you install the processor, the gold triangle (3) on the processor must be aligned
with the triangle (4) embossed on the processor slot.
Reverse this procedure to install the processor.
70
Chapter 4 Removal and replacement procedures
Modem module
NOTE: The modem module spare part kit does not include a modem module cable. The modem
module cable is included in the Cable Kit, spare part number 457615-001.
Description
Spare part number
Modem module
441074-001
Before removing the modem module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
f.
Display assembly (see Display assembly on page 51)
g.
Top cover (see Top cover on page 55)
h.
System board (see System board on page 61)
Remove the modem module:
1.
Turn the system board upside down, with the USB connectors toward you.
2.
Remove the two Phillips PM2.5×4.0 screws (1) that secure the modem module to the system board.
Component replacement procedures
71
3.
Lift the modem module (2) straight up to disconnect it from the system board.
4.
Remove the modem module.
Reverse this procedure to install the modem module.
72
Chapter 4 Removal and replacement procedures
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all
passwords and CMOS settings to be cleared.
Description
Spare part number
RTC battery
449137-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 35).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 36)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover and keyboard (see Switch cover and keyboard on page 45)
d.
Speaker (see Speaker on page 49)
e.
Display lid switch module (see Display lid switch module on page 50)
f.
Display assembly (see Display assembly on page 51)
g.
Top cover (see Top cover on page 55)
h.
System board (see System board on page 61)
Remove the RTC battery:
1.
Turn the system board upside down, with the audio connectors toward you.
Component replacement procedures
73
2.
Remove the RTC battery from the socket on the system board.
Reverse this procedure to install the RTC battery.
74
Chapter 4 Removal and replacement procedures
5
Computer Setup
Starting Computer Setup
Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system
is not working or will not load.
NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your
computer.
NOTE: Pointing devices are not supported in Computer Setup. You must use the keyboard to navigate
and make selections.
NOTE: An external keyboard connected by USB can be used with Computer Setup only if USB legacy
support is enabled.
To start Computer Setup:
1.
Turn on or restart the computer.
2.
Before Windows® opens and while the "F10 = ROM Based Setup" message is displayed in the
lower-left corner of the screen, press f10.
Starting Computer Setup
75
Using Computer Setup
Navigating and selecting in Computer Setup
The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and
System Configuration menus.
1.
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
Because Computer Setup is not Windows-based, it does not support the TouchPad. Navigation
and selection are by keystroke:
●
To choose a menu or a menu item, use the arrow keys.
●
To select an item, press enter.
●
To close open dialog boxes and return to the main Computer Setup screen, press esc.
●
To view navigation information, press f1.
●
To change the language, press f2.
2.
Select the File, Security, Diagnostics or System Configuration menu.
3.
To exit Computer Setup, choose one of the following methods:
●
To exit Computer Setup without saving your preferences, use the arrow keys to select File >
Ignore changes and exit. Then follow the instructions on the screen.
●
To save your preferences and exit Computer Setup, use the arrow keys to select File > Save
changes and exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
Restoring factory settings in Computer Setup
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1.
Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the
"F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen.
2.
Use the arrow keys to select File > Restore defaults, and then press enter.
3.
When the confirmation dialog box opens, press f10.
4.
To save your preferences and exit Computer Setup, use the arrow keys to select File > Save
changes and exit. Then follow the instructions on the screen.
Your preferences go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the factory
settings.
76
Chapter 5 Computer Setup
Computer Setup menus
The menu tables in this section provide an overview of Computer Setup options.
NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your
computer.
File menu
Select
To do this
System information
●
View identification information for the computer and the batteries in the system.
●
View specification information for the processor, cache and memory size,
system ROM, video revision, and keyboard controller version.
Restore defaults
Replace the configuration settings in Computer Setup with the original factory
settings. (Password settings and security settings are not changed when you restore
the factory settings.)
Ignore changes and exit
Cancel any changes entered during the current session. Then exit and restart the
computer.
Save changes and exit
Save any changes entered during the current session. Then exit and restart the
computer. Your changes go into effect when the computer restarts.
Computer Setup menus
77
Security menu
NOTE:
Some of the menu items listed in this section may not be supported by your computer.
Select
To do this
Setup Password
Enter, change, or delete a setup password.
Power-On Password
Enter, change, or delete a power-on password.
Password Options
●
Enable/disable stringent security.
●
Enable/disable the password requirement on computer restart.
●
Enable/disable DriveLock on any computer hard drive.
●
Change a DriveLock user password or master password.
DriveLock Passwords
NOTE: DriveLock settings are accessible only when you enter Computer Setup by
turning on (not restarting) the computer.
System IDs
Enter a user-defined computer asset tracking number and ownership tag.
Disk Sanitizer
Run Disk Sanitizer to destroy all existing data on the primary hard drive. The following
options are available:
●
Fast: Runs the Disk Sanitizer erase cycle once.
●
Optimum: Runs the Disk Sanitizer erase cycle 3 times.
●
Custom: Allows you to select the desired number of Disk Sanitizer erase cycles
from a list.
●
Last status: Provides information about the last time Disk Sanitizer ran on the
computer.
CAUTION: If you run Disk Sanitizer, the data on the primary hard drive is destroyed
permanently.
Diagnostics menu
78
Select
To do this
HDD Self-Test options
Run a comprehensive self-test on any hard drive in the system.
Memory Check
Run a comprehensive test on system memory.
Startup check
Verify the system components needed for starting the computer.
Chapter 5 Computer Setup
System Configuration menu
NOTE:
Some of the listed System Configuration options may not be supported by your computer.
Select
To do this
Language (or press f2)
Change the Computer Setup language.
Boot Options
●
Set an f9, f10, and f12 delay when starting up.
●
Enable/disable CD-ROM boot.
●
Enable/disable floppy boot.
●
Enable/disable internal network adapter boot and set the boot mode (PXE).
●
Enable/disable MultiBoot, which sets a boot order that can include most boot
devices in the system.
●
Set the Express Boot Popup delay in seconds.
●
Set the boot order.
●
Swap the functions of the fn key and left ctrl key.
●
Enable/disable USB legacy support. When enabled, USB legacy support allows
the following:
Device Configurations
Built-In Device Options
Port Options
◦
Use of a USB keyboard in Computer Setup even when a Windows
operating system is not running.
◦
Startup from bootable USB devices, including a hard drive, diskette drive,
or optical drive connected by a USB port to the computer.
●
Enable/disable BIOS DMA data transfers.
●
Enable/disable fan always on while connected to an AC outlet.
●
Enable/disable Data Execution Prevention. When enabled, the processor can
disable some virus code execution, which helps to improve computer
security.
●
Enable/disable SATA Native Mode.
●
Enable/disable Dual Core CPU.
●
Choose Bit-shift or LBA-assisted HDD Translation Mode.
●
Enable/disable Virtualization Technology.
●
Enable/disable embedded WLAN Device Radio.
●
Enable/disable Wake on LAN.
●
Enable/disable the optical disc drive.
●
Enable/disable the USB port.
●
Enable/disable the ExpressCard slot.
Computer Setup menus
79
6
Specifications
Computer specifications
Metric
U.S.
Length
28.49 cm
11.22 in
Width
39.62 cm
15.60 in
Height (front to rear)
3.23 to 3.58 cm
1.27 to 1.41 in
Weight (equipped with optical drive, hard drive, and battery)
2.94 kg
6.48 lbs
Dimensions
Input power
Operating voltage
19.0 V dc @ 4.74 A – 90 W
Operating current
4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating (14.7 to 10.1 psia)
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating (14.7 to 4.4 psia)
-15 m to 12,192 m
-50 ft to 40,000 ft
Shock
Operating
125 g, 2 ms, half-sine
Nonoperating
200 g, 2 ms, half-sine
Random vibration
Operating
80
Chapter 6 Specifications
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
Metric
Nonoperating
U.S.
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
17.0-inch, WXGA display specifications
Metric
U.S.
Height
24.4 cm
9.6 in
Width
38.1 cm
15.0 in
Diagonal
43.2 cm
17.0 in
Number of colors
Up to 16.8 million
Contrast ratio
200:1 (typical)
Brightness
180 nits (typical)
Dimensions
Pixel resolution
Pitch
0.259 × 0.259 mm
Format
1140 × 900
Configuration
RGB vertical stripe
Backlight
CCFT
Character display
80 × 25
Total power consumption
6.5 W
Viewing angle
+/-45° horizontal, +15°/-35° vertical (typical)
17.0-inch, WXGA display specifications
81
Hard drive specifications
250-GB*
160-GB*
120-GB*
80-GB*
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
70 mm
Weight
101 g
101 g
101 g
101 g
Interface type
SATA
SATA
SATA
SATA
Transfer rate
100 MB/sec
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
ATA security
Dimensions
Seek times (typical read, including setting)
Single track
3 ms
3 ms
3 ms
3 ms
Average
13 ms
13 ms
13 ms
13 ms
Maximum
24 ms
24 ms
24 ms
24 ms
Logical blocks
495,665,155
312,560,640
234,420,480
156,280,320
Disc rotational speed
5400 rpm
5400 rpm
5400 rpm
5400 rpm
Operating temperature
5°C to 55°C (41°F to 131°F)
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive
specifications may differ slightly.
NOTE: Certain restrictions and exclusions apply. Contact technical support for details.
82
Chapter 6 Specifications
DVD±RW and CD-RW Double-Layer Combo Drive
specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video CD), Multisession
CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CDRW), CD-R, CD-RW, DVD-ROM (DVD-5,
DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
Access time
CD
DVD
Random
< 175 ms
< 230 ms
Cache buffer
2 MB
DVD+R, DVD+RW, DVD-R, DVDRW, DVD-RAM
Data transfer rate
24X CD-ROM
3,600 KB/sec
8X DVD-ROM
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
24X DVD+R
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
DVD±RW and CD-RW Double-Layer Combo Drive specifications
83
DVD/CD-RW Combo Drive specifications
Applicable disc
Center hole diameter
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I,
CD-I Bridge (Photo-CD, Video CD), Multisession
CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CDRW), CD-R, CD-RW, DVD-ROM (DVD-5,
DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
1.5 cm (0.59 in)
Disc diameter
Standard disc
12 cm (4.72 in)
Mini disc
8 cm (3.15 in)
Disc thickness
1.2 mm (0.047 in)
Track pitch
0.74 µm
Access time
CD
DVD
Random
< 110 ms
< 130 ms
Full stroke
< 210 ms
< 225 ms
Audio output level
Line-out, 0.7 Vrms
Cache buffer
2 MB
Data transfer rate
84
24X CD-ROM
3,600 KB/sec
8X DVD
3,600 KB/sec
24X CD-R
3,600 KB/sec
24X CD-RW
3,600 KB/sec
Transfer mode
Multiword DMA mode 2
Startup time
< 15 seconds
Stop time
< 6 seconds
Chapter 6 Specifications
System DMA specifications
Hardware DMA
System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Available for ExpressCard
DMA6
Not assigned
DMA7
Not assigned
*ExpressCard controller can use DMA 1, 2, or 5.
System DMA specifications
85
System interrupt specifications
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial
port may assert IRQ3 or IRQ4.
86
Chapter 6 Specifications
System I/O address specifications
I/O address (hex)
System function (shipping configuration)
000 - 00F
DMA controller no. 1
010 - 01F
Unused
020 - 021
Interrupt controller no. 1
022 - 024
Opti chipset configuration registers
025 - 03F
Unused
02E - 02F
87334 “Super I/O” configuration for CPU
040 - 05F
Counter/timer registers
044 - 05F
Unused
060
Keyboard controller
061
Port B
062 - 063
Unused
064
Keyboard controller
065 - 06F
Unused
070 - 071
NMI enable/RTC
072 - 07F
Unused
080 - 08F
DMA page registers
090 - 091
Unused
092
Port A
093 - 09F
Unused
0A0 - 0A1
Interrupt controller no. 2
I/O Address (hex)
System function (shipping configuration)
0A2 - 0BF
Unused
0C0 - 0DF
DMA controller no. 2
0E0 - 0EF
Unused
0F0 - 0F1
Coprocessor busy clear/reset
0F2 - 0FF
Unused
100 - 16F
Unused
170 - 177
Secondary fixed disk controller
178 - 1EF
Unused
1F0 - 1F7
Primary fixed disk controller
1F8 - 200
Unused
201
JoyStick (decoded in ESS1688)
202 - 21F
Unused
System I/O address specifications
87
88
I/O address (hex)
System function (shipping configuration)
220 - 22F
Entertainment audio
230 - 26D
Unused
26E - 26
Unused
278 - 27F
Unused
280 - 2AB
Unused
2A0 - 2A7
Unused
2A8 - 2E7
Unused
2E8 - 2EF
Reserved serial port
2F0 - 2F7
Unused
2F8 - 2FF
Infrared port
300 - 31F
Unused
320 - 36F
Unused
370 - 377
Secondary diskette drive controller
378 - 37F
Parallel port (LPT1/default)
380 - 387
Unused
388 - 38B
FM synthesizer—OPL3
38C - 3AF
Unused
3B0 - 3BB
VGA
3BC - 3BF
Reserved (parallel port/no EPP support)
3C0 - 3DF
VGA
3E0 - 3E1
ExpressCard controller in CPU
3E2 - 3E3
Unused
3E8 - 3EF
Internal modem
3F0 - 3F7
“A” diskette controller
3F8 - 3FF
Serial port (COM1/default)
CF8 - CFB
PCI configuration index register (PCIDIVO-1)
CFC - CFF
PCI configuration data register (PCIDIVO-1)
Chapter 6 Specifications
System memory map specifications
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
48 KB
000C0000-000CBFFF
Video BIOS
160 KB
000C8000-000E7FFF
Unused
64 KB
000E8000-000FFFFF
System BIOS
15 MB
00100000-00FFFFFF
Extended memory
58 MB
04800000-07FFFFFF
Super extended memory
58 MB
04800000-07FFFFFF
Unused
2 MB
08000000-080FFFFF
Video memory (direct access)
4 GB
08200000-FFFEFFFF
Unused
64 KB
FFFF0000-FFFFFFFF
System BIOS
System memory map specifications
89
7
Screw listing
This section provides specification and reference information for the screws and screw locks used in
the computer. All screws listed in this section are available in the Screw Kit, spare part number
456615-001.
90
Chapter 7 Screw listing
Phillips PM2.0×5.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
4
5.0 mm
2.0 mm
5.0 mm
Where used:
(1) Two captive screws that secure the hard drive bay cover to the computer (screws are captured on
the cover by C-clips)
(2) One captive screw that secures the WLAN module compartment cover to the computer (screw is
captured on the cover by a C-clip)
(3) One captive screw that secures the memory module compartment cover to the computer (screw is
captured on the cover by a C-clip)
Phillips PM2.0×5.0 captive screw
91
Phillips PM2.5×13.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
1
13.0 mm
2.5 mm
5.0 mm
Where used: One captive screw that secures the hard drive to the computer (screw is secured to the
hard drive bracket)
92
Chapter 7 Screw listing
Phillips PM3.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
4.0 mm
3.0 mm
5.0 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
Phillips PM3.0×4.0 screw
93
Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
4
4.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the WLAN module to the system board
Where used: 2 screws that secure the modem module to the system board
94
Chapter 7 Screw listing
Torx T8M2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
23
7.0 mm
2.5 mm
5.0 mm
Where used:
(1) One screw that secures the optical drive to the computer
(2) Two screws that secure the keyboard to the computer
(3) Three screws that secure the switch cover to the computer
Torx T8M2.5×7.0 screw
95
Where used: 4 screws that secure the display assembly to the computer
Where used: 10 screws that secure the top cover to the base enclosure
Where used: 3 screws that secure the top cover to the base enclosure
96
Chapter 7 Screw listing
Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
14
4.0 mm
2.0 mm
4.5 mm
Where used: 2 screws that secure the optical drive bracket to the optical drive
Phillips PM2.0×4.0 screw
97
Where used: 8 screws that secure the display hinges to the display assembly
Where used: 2 screws that secure the TouchPad Bracket and TouchPad button board to the top cover
Where used: 2 screws that secure the Bluetooth module to the base enclosure
98
Chapter 7 Screw listing
Torx T8M2.5×9.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
2
9.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the switch cover to the computer
Torx T8M2.5×9.0 screw
99
Torx T8M2.5×3.0 broad-head screw
Color
Quantity
Length
Thread
Head diameter
Black
3
3.0 mm
2.5 mm
8.0 mm
Where used: 3 screws that secure the switch cover to the computer
100 Chapter 7 Screw listing
Torx T8M2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
7
4.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the speaker to the computer
Where used: One screw that secures the top cover to the base enclosure
Torx T8M2.5×4.0 screw 101
Where used: 4 screws that secure the battery connector board to the base enclosure
102 Chapter 7 Screw listing
Torx T8M2.5×6.0 screw
Color
Quantity
Length
Thread
Heat width
Black
16
6.0 mm
2.5 mm
5.0 mm
Where used: 8 screws that secure the display bezel to the display assembly
Where used: 4 screws that secure the display panel to the display enclosure
Torx T8M2.5×6.0 screw 103
Where used:
(1) One screw that secures the system board to the base enclosure
(2) Three screws that secure the battery connector board to the base enclosure
104 Chapter 7 Screw listing
Phillips PM2.0×2.0 broad-head screw
Color
Quantity
Length
Thread
Head diameter
Black
3
2.0 mm
2.0 mm
6.0 mm
Where used: 3 screws that secure the top cover to the base enclosure
Phillips PM2.0×2.0 broad-head screw 105
Phillips PM2.0×6.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
1
6.0 mm
2.0 mm
4.5 mm
Where used: One screw that secures the system board to the base enclosure
106 Chapter 7 Screw listing
Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
1
7.0 mm
2.5 mm
5.0 mm
Where used: One screw that secures the fan to the base enclosure
Phillips PM2.5×7.0 screw 107
Phillips PM2.5×7.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
1
7.0 mm
2.5 mm
5.0 mm
Where used: One captive screw that secures the fan to the base enclosure (screw is secured to the
fan by a C-clip)
108 Chapter 7 Screw listing
Phillips PM2.5×10.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
6
10.0 mm
2.5 mm
5.0 mm
Where used: 6 captive screws that secure the heat sink to the system board (screws are secured to
the heat sink by C-clips)
Phillips PM2.5×10.0 captive screw 109
8
Backup and recovery
Creating recovery discs in Windows Vista
After setting up the computer for the first time, be sure to create a set of recovery discs of the full factory
image. The recovery discs are used to start up (boot) the computer and recover the operating system
and software to factory settings in case of system instability or failure.
Note the following guidelines before creating recovery discs:
●
Use any of the following types of discs: CD-R, DVD+R, DVD+R DL, DVD-R, or DVD-R DL
(purchased separately). The discs you use will depend on the type of optical drive installed in your
computer. Because DVDs store more information than CDs, DVDs and DVDs with double-layer
(DL) support reduce the number of discs required.
NOTE: Read-write discs, such as CD-RW, DVD+RW, and DVD-RW, are not compatible with the
Backup & Recovery Manager software.
●
The computer must be connected to AC power during the process.
●
Only one set of the recovery discs can be created per computer.
●
Number each disc before inserting it into the optical drive of the computer.
●
If necessary, you can cancel the disc creation before you have finished creating the recovery discs.
The next time you select Create a set of recovery discs (Recommended), you will be prompted
to continue the disc creation.
To create a set of recovery discs:
1.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
2.
Click Next.
3.
Click Create a set of recovery discs (Recommended), and then click Next.
4.
Follow the on-screen instructions.
110 Chapter 8 Backup and recovery
Backing up your information in Windows Vista
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
HP Backup & Recovery Manager to create an entire drive backup as soon as you set up your computer.
With HP Backup & Recovery Manager, you can perform the following tasks:
●
Backing up your information regularly to protect your important system files
●
Creating system recovery points that allow you to reverse undesireable changes to your computer
by restoring the computer to an earlier state
●
Scheduling backups at specific intervals or events
When to back up
●
On a regularly scheduled basis
NOTE:
Set reminders to back up your information periodically.
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
Backup suggestions
●
Create a set of recovery discs using HP Backup & Recovery Manager.
●
Create system recovery points using HP Backup & Recovery Manager, and periodically copy them
to disc.
●
Store personal files in the Documents folder and back up these folders periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a.
Display the screen.
b.
Copy the screen.
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, and then select Edit > Paste.
NOTE: Before you can perform backup and recovery procedures, the computer must be connected
to external power.
NOTE: Drivers, utilities, and applications installed by HP can be copied to a CD or to a DVD using HP
Backup & Recovery Manager.
Backing up your information in Windows Vista 111
Backing up specific files or folders
You can back up specific files or folders to the recovery partition on the hard drive, to an optional external
hard drive, or to optical discs (CDs or DVDs).
NOTE: This process will take several minutes, depending on the file size and the speed of the
computer.
To back up specific files or folders:
1.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
2.
Click Next.
3.
Click Create or manage backups, and then click Next.
4.
Click Back up user created files and folders, and then click Next.
5.
Follow the on-screen instructions.
Backing up the entire hard drive
When you perform a complete backup of the hard drive, you are saving the full factory image, including
the Windows® operating system, software applications, and all personal files and folders.
NOTE: A copy of the entire hard drive image can be stored on another hard drive, on a network drive,
or on recovery discs that you create.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
To back up your entire hard drive:
1.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
2.
Click Next.
3.
Click Create or manage backups, and then click Next.
4.
Click Create or manage Entire Drive Backups, and then click Next.
5.
Follow the on-screen instructions.
112 Chapter 8 Backup and recovery
Creating recovery points
When you back up modifications since your last backup, you are creating system recovery points. This
allows you to save a snapshot of your hard drive at a specific point in time. You can then recover back
to that point if you want to reverse subsequent changes made to your system.
NOTE: The first system recovery point, a snapshot of the entire image, is automatically created the
first time you perform a backup. Subsequent recovery points make copies of changes made after that
time.
HP recommends that you create recovery points at the following times:
●
Before you add or extensively modify software or hardware
●
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier recovery point does not affect data files or e-mails created since that
recovery point.
To create a system recovery point:
1.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
2.
Click Next.
3.
Click Create or manage backups, and then click Next.
4.
Click Create or manage Recovery Points, and then click Next.
5.
Follow the on-screen instructions.
Scheduling backups
Use HP Backup Scheduler to schedule backups for the entire system, for recovery points, or for specific
files and folders. With this tool, you can schedule backups at specific intervals (daily, weekly, or monthly)
or at specific events, such as at system restart or when you dock to an optional docking station (select
models only).
To schedule backups:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup Scheduler.
2.
Follow the on-screen instructions.
Backing up your information in Windows Vista 113
Performing a recovery in Windows Vista
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
HP Backup & Recovery Manager to create an entire drive backup as soon as you set up your computer.
HP Backup & Recovery Manager helps you with the following tasks for safeguarding your information
and restoring it in case of a system failure:
●
Recovering important files—This feature helps you reinstall important files without performing a full
system recovery.
●
Performing a full system recovery—With HP Backup & Recovery Manager, you can recover your
full factory image if you experience system failure or instability. HP Backup & Recovery Manager
works from a dedicated recovery partition on the hard drive or from recovery discs you create.
Performing a recovery from the recovery discs
To perform a recovery from the recovery discs, follow these steps:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Performing a recovery from the hard drive
There are 2 ways to initiate a recovery from the hard drive:
●
From within Windows
●
From the recovery partition
114 Chapter 8 Backup and recovery
Initiating a recovery in Windows
To initiate a recovery in Windows, follow these steps:
1.
Back up all personal files.
2.
Select Start > All Programs > HP Backup & Recovery > Backup & Recovery Manager.
3.
Click Next.
4.
Click Perform a recovery, and then click Next.
5.
Follow the on-screen instructions.
Initiating a recovery from the hard drive recovery partition
To initiate a recovery from the hard drive recovery partition, follow these steps:
1.
Back up all personal files.
2.
Restart the computer, and then press f11 before the Windows operating system loads.
3.
Click a recovery option, and then click Next.
4.
Follow the on-screen instructions.
Performing a recovery in Windows Vista 115
Creating recovery discs in Windows XP
After setting up the computer for the first time, be sure to create a set of recovery discs of the full factory
image. The recovery discs are used to start up (boot) the computer and recover the operating system
and software to factory settings in case of system instability or failure.
Note the following guidelines before creating recovery discs:
●
Use any of the following types of discs: CD-R, DVD+R, DVD+R DL, DVD-R, or DVD-R DL
(purchased separately). The discs you use will depend on the type of optical drive installed in your
computer. Because DVDs store more information than CDs, DVDs and DVDs with double-layer
(DL) support reduce the number of discs required.
NOTE: Read-write discs, such as CD-RW, DVD+RW, and DVD-RW, are not compatible with the
HP Backup and Recovery Manager software.
●
The computer must be connected to AC power during the process.
●
Only one set of the recovery discs can be created per computer.
●
Number each disc before inserting it into the optical drive of the computer.
●
If necessary, you can cancel the disc creation before you have finished creating the recovery discs.
The next time you select Create factory software recovery CDs or DVDs to recover the system
(Highly recommended), you will be prompted to continue the disc creation.
To create a set of recovery discs:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager.
2.
Click Next.
3.
Click Create factory software recovery CDs or DVDs to recover the system (Highly
recommended), and then click Next.
4.
Follow the on-screen instructions.
116 Chapter 8 Backup and recovery
Backing up your information in Windows XP
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
HP Backup and Recovery Manager to create an entire drive backup as soon as you set up your
computer.
With HP Backup and Recovery Manager, you can perform the following tasks:
●
Backing up your information regularly to protect your important system files
●
Creating system recovery points that allow you to reverse undesireable changes to your computer
by restoring the computer to an earlier state
●
Scheduling backups at specific intervals or events
When to back up
●
On a regularly scheduled basis
NOTE:
Set reminders to back up your information periodically.
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
Backup suggestions
●
Create a set of recovery discs using HP Backup and Recovery Manager.
●
Create system recovery points using HP Backup and Recovery Manager, and periodically copy
them to disc.
●
Store personal files in the My Documents folder and back up these folders periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document:
a.
Display the screen.
b.
Copy the screen.
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, and then select Edit > Paste.
NOTE: Before you can perform backup and recovery procedures, the computer must be connected
to external power.
NOTE: Drivers, utilities, and applications installed by HP can be copied to a CD or to a DVD using HP
Backup and Recovery Manager.
Backing up your information in Windows XP 117
Backing up specific files or folders
You can back up specific files or folders to the recovery partition on the hard drive, to an optional external
hard drive, or to optical discs (CDs or DVDs).
NOTE: This process will take several minutes, depending on the file size and the speed of the
computer.
To back up specific files or folders:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager.
2.
Click Next.
3.
Click Back up to protect system settings and important data files, and then click Next.
4.
Click Back up individual files and folders, and then click Next.
5.
Follow the on-screen instructions.
Backing up the entire hard drive
When you perform a complete backup of the hard drive, you are saving the full factory image, including
the Windows® operating system, software applications, and all personal files and folders.
NOTE: A copy of the entire hard drive image can be stored on another hard drive, on a network drive,
or on recovery discs that you create.
NOTE: This process may take over an hour, depending on your computer speed and the amount of
data being stored.
To back up your entire hard drive:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager.
2.
Click Next.
3.
Click Back up to protect system settings and important data files, and then click Next.
4.
Click Back up entire hard drive, and then click Next.
5.
Follow the on-screen instructions.
118 Chapter 8 Backup and recovery
Creating recovery points
When you back up modifications since your last backup, you are creating system recovery points. This
allows you to save a snapshot of your hard drive at a specific point in time. You can then recover back
to that point if you want to reverse subsequent changes made to your system.
NOTE: The first system recovery point, a snapshot of the entire image, is automatically created the
first time you perform a backup. Subsequent recovery points make copies of changes made after that
time.
HP recommends that you create recovery points at the following times:
●
Before you add or extensively modify software or hardware
●
Periodically, whenever the system is performing optimally
NOTE: Recovering to an earlier recovery point does not affect data files or e-mails created since that
recovery point.
To create a system recovery point:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager.
2.
Click Next.
3.
Click Back up to protect system settings and important data files, and then click Next.
4.
Click Create or manage Recovery Points, and then click Next.
5.
Follow the on-screen instructions.
Scheduling backups
Use HP Backup Scheduler to schedule backups for the entire system, for recovery points, or for specific
files and folders. With this tool, you can schedule backups at specific intervals (daily, weekly, or monthly)
or at specific events, such as at system restart or when you dock to an optional docking station (select
models only).
To schedule backups:
1.
Select Start > All Programs > HP Backup & Recovery > HP Backup Scheduler.
2.
Follow the on-screen instructions.
Backing up your information in Windows XP 119
Performing a recovery in Windows XP
NOTE: You can only recover files that you have previously backed up. HP recommends that you use
HP Backup and Recovery Manager to create an entire drive backup as soon as you set up your
computer.
HP Backup and Recovery Manager helps you with the following tasks for safeguarding your information
and restoring it in case of a system failure:
●
Recovering important files—This feature helps you reinstall important files without performing a full
system recovery.
●
Performing a full system recovery—With HP Backup and Recovery Manager, you can recover your
full factory image if you experience system failure or instability. HP Backup and Recovery Manager
works from a dedicated recovery partition on the hard drive or from recovery discs you create.
Performing a recovery from the recovery discs
To perform a recovery from the recovery discs, follow these steps:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Performing a recovery from the hard drive
There are 2 ways to initiate a recovery from the hard drive:
●
From within Windows
●
From the recovery partition
120 Chapter 8 Backup and recovery
Initiating a recovery in Windows
To initiate a recovery in Windows, follow these steps:
1.
Back up all personal files.
2.
Select Start > All Programs > HP Backup & Recovery > HP Backup and Recovery Manager.
3.
Click Next.
4.
Click Recover important files or the entire system, and then click Next.
5.
Follow the on-screen instructions.
Performing a recovery in Windows XP 121
Initiating a recovery from the hard drive recovery partition
To initiate a recovery from the hard drive recovery partition, follow these steps:
1.
Back up all personal files.
2.
Restart the computer, and then press f11 before the Windows operating system loads.
3.
Click a recovery option, and then click Next.
4.
Follow the on-screen instructions.
122 Chapter 8 Backup and recovery
9
Connector pin assignments
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
Audio-out (headphone) 123
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
124 Chapter 9 Connector pin assignments
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
RJ-11 (modem) 125
Universal Serial Bus
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
126 Chapter 9 Connector pin assignments
10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or
region where the computer is used.
Requirements for all countries and regions
The requirements listed below are applicable to all countries and regions:
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage
rating of 125 or 250 V AC, as required by the power system of each country or region.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
Requirements for all countries and regions 127
Requirements for specific countries and regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
Korea
EK
4
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall
plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
128 Chapter 10 Power cord set requirements
11 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components. When you remove these
components, handle them carefully.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or
see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific
details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from
one computer model to another.
Battery 129
Perform the following steps to disassemble the display assembly:
1.
Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2.
Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3.
Remove the display bezel (3).
130 Chapter 11 Recycling
4.
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5.
Remove all screws (1) that secure the display panel assembly to the display enclosure.
6.
Remove the display panel assembly (2) from the display enclosure.
7.
Turn the display panel assembly upside down.
8.
Remove all screws that secure the display panel frame to the display panel.
9.
Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
Display 131
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
132 Chapter 11 Recycling
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
17. Remove the backlight frame from the display panel.
Display 133
18. Remove the backlight from the backlight frame.
19. Disconnect the display panel cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
134 Chapter 11 Recycling
Index
A
AC adapter, spare part
number 21, 26
antenna, disconnecting 40
audio, product description 3
audio-in jack
location 8
pin assignments 123
audio-out jack
location 8
pin assignments 123
B
backing up 111
backup
files and folders 112, 118
hard drive 112, 118
modifications made to
system 119
modifications made to the
system 113
scheduling 113, 119
base enclosure, spare part
number 15, 26
battery
location 10
removal 32
spare part number 15, 26,
32
battery bay 10
battery connector board
removal 64
spare part number 14, 26,
64
battery latches 10
battery light 9
Blu-ray Disc ROM and SuperMulti
DVD±R/RW Double-Layer Drive
precautions 28
removal 43
spare part number 17, 20,
24, 43
Bluetooth module
removal 60
spare part number 15, 22,
60
Bluetooth module cable,
illustrated 19
boot options 79
boot order 79
bottom components 10
button components 6
buttons
power 6
TouchPad 5
wireless 6
C
Cable Kit
contents 19
spare part number 17, 19,
26
cables, service considerations 28
carrying case, spare part
number 21, 22
chipset, product description 1
CMOS clearing 32
components
bottom 10
buttons 6
front 8
keys 7
left-side 9
lights 6
pointing devices 5
right-side 8
speaker 6
top 5
TouchPad 5
computer feet
locations 34
spare part number 34
Computer Setup
accessing 75
Diagnostics menu 78
File menu 77
navigating and selecting 76
restoring factory settings 76
Security menu 78
System Configuration
menu 79
using 76
computer specifications 80
connectors
power 9
service considerations 28
creating recovery points 113,
119
D
Diagnostics menu 78
Disk Sanitizer 78
diskette drive
precautions 28
product description 2
spare part number 21, 22
display assembly
removal 51
spare part numbers 13, 24,
51
display bezel
removal 52
spare part number 53
display component recycling 129
display enclosure, spare part
number 13, 25
Index 135
display hinge
removal 54
spare part number 13, 24,
54
display inverter
removal 53
spare part number 13, 26,
53
display lid switch module
illustrated 19
removal 50
display panel
product description 1
removal 53
display specifications 81
DriveLock password 78
drives
boot order 79
preventing damage 28
DVD/CD-RW Combo Drive
precautions 28
removal 43
spare part number 17, 20,
26, 43
specifications 84
DVD±RW and CD-RW Combo
Drive
precautions 28
removal 42
spare part numbers 17, 20,
26, 42
specifications 83
E
electrostatic discharge 29
entire hard drive backup 118
esc key 7
Ethernet, product description 3
Execution Disable 79
ExpressCard slot 9
ExpressCard slot bezel
removal 56
ExpressCard slot bezel,
illustrated 18
external media cards, product
description 3
external monitor port
location 9
pin assignments 124
136 Index
F
fan
removal 65
spare part number 14, 22,
65
feet
locations 34
spare part number 34
File menu 77
fn key 7
front components 8
function keys 7
G
graphics, product description
grounding equipment and
methods 31
1
H
hard drive
location 10
precautions 28
product description 2
removal 36
spare part numbers 17, 20,
26, 36
specifications 82
hard drive backup 112, 118
hard drive bay 10
hard drive bay cover
illustrated 18
removal 36
hard drive bracket, removal 37
hard drive recovery 114, 120
hard drive test 78
headphone jack
location 8
pin assignments 123
heat sink
removal 67
spare part number 14, 25,
67
hinge
removal 54
spare part number 13, 54
I
I/O address specifications 87
interrupt specifications 86
J
jacks
audio-in 8
audio-out 8
headphone 8
microphone 8
modem 9
network 9
RJ-11 9
RJ-45 9
K
key components 7
keyboard
product description 3
removal 45
spare part numbers 13, 25,
45
keypad keys 7
keys
esc 7
fn 7
function 7
keypad 7
Windows applications 7
Windows logo 7
L
language, changing in Computer
Setup 79
left-side components 9
legacy support, Universal Serial
Bus (USB) 75, 79
light components 6
lights
battery 9
optical drive 8
power 7
wireless 6
Logo Kit, spare part number 21,
26
M
mass storage devices, spare part
numbers 20
memory check 78
memory map specifications 89
memory module
product description 2
removal 41
spare part numbers 17, 22,
41
memory module compartment 10
memory module compartment
cover
illustrated 18
removal 41
microphone jack
location 8
pin assignments 123
Miscellaneous TouchPad Kit, spare
part number 14
model name 1
modem jack
location 9
pin assignments 125
modem module
product description 3
removal 71
spare part number 15, 22,
71
monitor port
location 9
pin assignments 124
N
navigating in Computer Setup
network jack
location 9
pin assignments 125
76
O
operating system, product
description 4
optical drive
location 8
precautions 28
product description 2
removal 42
spare part numbers 17, 20,
42
specifications 83, 84
optical drive connector board
removal 64
spare part number 14, 26,
64
optical drive light 8
P
packing guidelines 30
password clearing 32
passwords 78
pin assignments
audio-in jack 123
audio-out jack 123
external monitor port 124
headphone jack 123
microphone jack 123
modem jack 125
monitor port 124
network jack 125
RJ-11 125
RJ-45 jack 125
Universal Serial Bus (USB)
port 126
plastic parts 27
Plastics Kit
contents 18
spare part number 14, 18,
25
pointing device
components 5
illustrated 5
product description 3
pointing device components
TouchPad 5
TouchPad buttons 5
TouchPad scroll zone 5
ports
external monitor 9
monitor 9
product description 3
Universal Serial Bus (USB) 9
power button 6
power connector 9
power cord
set requirements 127
spare part numbers 21, 22
power light 7
power requirements, product
description 4
power-on password 78
processor
product description 1
removal 62
spare part numbers 14, 24,
62
product description
audio 3
chipset 1
diskette drive 2
display panel 1
Ethernet 3
external media cards 3
graphics 1
hard drives 2
keyboard 3
memory module 2
modem module 3
operating system 4
optical drives 2
pointing devices 3
ports 3
power requirements 4
processors 1
product name 1
security 4
serviceability 4
wireless 3
product name 1
R
recovery discs
creating 110
using 114, 120
recovery partition 115, 122
recovery points 113, 119
removal/replacement
preliminaries 27
procedures 33
restoring Computer Setup factory
settings 76
right-side components 8
RJ-11 jack
location 9
pin assignments 125
RJ-11 jack cable
illustrated 19
release 62
RJ-45 jack
location 9
pin assignments 125
RTC battery
removal 32
spare part number 15, 32
Rubber Kit, spare part number 26
S
scheduling backups 113, 119
Index 137
Screw Kit
contents 90
spare part number 21, 25
screw listing 90
SD/MMC Card Reader 8
security cable slot 8
Security menu 78
security, product description 4
selecting in Computer Setup 76
serial number 11, 33
service considerations 27
serviceability, product
description 4
speaker
location 7
removal 49
spare part number 13, 26,
49
specifications
computer 80
display 81
DVD/CD-RW Combo Drive 84
DVD±RW and CD-RW Combo
Drive 83
hard drive 82
I/O addresses 87
interrupts 86
memory map 89
optical drive 83, 84
system DMA 85
startup check 78
static-shielding materials 31
stringent security 78
switch cover
removal 45
spare part number 13, 24,
45
system backup 112, 118
system board
removal 61
spare part numbers 14, 25,
61
System Configuration menu 79
system DMA 85
system fan 79
system information 77
system memory map 89
system recovery points 113, 119
138 Index
T
thermal material, replacement 68
tools required 27
top components 5
top cover
removal iii
spare part number 14, 26, iii
TouchPad 5
TouchPad board
removal 58
spare part number 14, 26,
58
TouchPad button board
removal 58
spare part number 14, 25,
58
TouchPad buttons 5
TouchPad components 5
TouchPad Miscellaneous Kit, spare
part number 26, 58
TouchPad scroll zone 5
transporting guidelines 30
U
Universal Serial Bus (USB) legacy
support 75, 79
unknown password 32
USB port
location 9
pin assignments 126
V
vents 9, 10
W
Windows applications key 7
Windows logo key 7
wireless antenna,
disconnecting 40
wireless button 6
wireless light 6
wireless, product description 3
WLAN module
removal 38
spare part numbers 15, 22,
24, 38
WLAN module compartment 10
WLAN module compartment cover
illustrated 18
removal 40
workstation guidelines 30
Download PDF