2014 harley davidson touring fuel moto micro efi tuner

FUEL MOTO MICRO EFI TUNER
INSTALLATION INSTRUCTIONS
2014
HARLEY DAVIDSON
TOURING
PARTS LIST
1
1
1
1
Micro Tuner Module
USB Cable
CD-ROM
Installation Guide
1
2
2
1
Alcohol swab
Velcro
Optimizers
Posi-tap
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Note: Fuel Moto USA and Fuel Moto Micro EFI Tuner fuel management systems are not legal for use or installation on motor vehicles operated on public highways in the State of California or other States
where similar emission and decibel regulation laws may apply. The user shall determine suitability of the product for his or her use. The user shall assume all risk and liability in violation of regulations and
any incurred financial obligations due to vehicle inspections or emissions tests.
Fuel Moto USA
2215 Kelbe Dr.,
Little Chute, WI 54140
Toll Free:877-729-4754
www.fuelmotousa.com
FIG.A
Remove the seat.
2.
Remove the bolts securing the fuel tank. Lift the tank for access to the
fuel injectors.
3.
Route the Micro EFI Tuner wiring harness from the seat area, over the
frame tube, and continue towards the front of the bike as shown in
Figure A.
4.
Unplug the stock wiring harness from each injector as shown in
Figure B.
5.
Attach the connectors from the Micro EFI Tuner to the stock wiring
harness and each injector.
unplug
unplug
FIG.C
FIG.B

1.
FM-019
Connect the orange wires to the front cylinder.
Toll Free: 877-729-4754
2014 Harley Davidson Touring - 2
FIG.D
6.
Locate the Throttle Position Sensor (TPS)
behind the air filter cover.
7.
Pull back the TPS connector boot.
8.
Using the supplied posi-tap, attach the grey
wire from the Micro EFI Tuner harness to the
Green/Purple wire on the stock harness.
9.
Push the boot back onto the connector.
FIG.E

10. Attach the ground wire from the Micro EFI Tuner to the negative side of
the battery as shown in Figure E.
FIG.F
11. Using the supplied velcro, secure the Micro EFI Tuner to the side of the
battery as shown in Figure F.
Make sure to clean both surfaces with the supplied alcohol swab prior
to applying the velcro.
12. Reinstall the fuel tank and seats.
FM-019
Toll Free: 877-729-4754
2014 Harley Davidson Touring - 3
13. Unplug the front O2 sensor from the stock wiring harness as shown in
Figure G.
rear O2
FIG.G
front O2
This connector is located on the right side of the battery.
14. Unplug the rear O2 sensor from the stock wiring harness as shown in
Figure G.
This connector is located on the right side of the battery.

FIG.H
15. Attach the Micro EFI Tuner O2 optimizers to the stock wiring harnesses
as shown in Figure H.
The stock O2 sensor does not need to be connected to anything. The
sensor can be removed completely from the motorcycle if desired.
16. Replace the bolts securing the fuel tank.
17. Reinstall the seat.
FM-019
Toll Free: 877-729-4754
2014 Harley Davidson Touring - 4
Selecting the Map Position
The Fuel Moto Micro EFI Tuner comes loaded with up to ten maps. Using a #1
Phillips screwdriver, turn the map select dial to toggle between the loaded maps.
Refer to the map position table below for the maps included in your Micro EFI
Tuner Module.
USB Port
Using the RPM Range Dials
The Low, Mid, and High RPM Dials refer to the RPM range, in thirds, of your
vehicle. Each dial allows +/- 10% fuel adjustment on top of what fuel changes
are done in the map. With the dial facing straight up, there is no additional
fuel change
For example, if your vehicle revs to 6000 RPM:
• The low RPM dial will adjust 0-2000 RPM
• The mid RPM dial will adjust 2001-4000 RPM
• The high RPM dial will adjust 4001-6000 RPM
HIGH RPM Dial
MID RPM Dial
LOW RPM Dial
MAP Select
STATUS Light
Using Fuel Moto Micro EFI Tuner Control Center
Take your tuning to the next level with the Fuel Moto Micro EFI Tuner Control Center
software.
1
Insert the CD provided into your computer’s CD-ROM drive. The launch program
will run automatically. If auto-run is disabled, double-click the My Computer
icon then double-click the CD drive icon. Double-click Fuel Moto Micro EFI Tuner
setup.exe to manually start the CD.
2
Click Install Software and follow the on-screen instructions to install the Micro
Tuner software. The Micro EFI Tuner software and maps will be stored in C:\
Program Files\Fuel Moto Micro EFI Tuner Control Center.
3
Click Map Database. All maps will automatically be installed to the C:\Program
Files\Fuel Moto Micro EFI Tuner Control Center\maps folder.
Loading Additional Maps
1 Connect the USB cable from the computer to the Fuel Moto Micro EFI Tuner
Module. Verify the cable is fully seated in the Fuel Moto Micro EFI Tuner Module.
2
Run the Fuel Moto Micro EFI Tuner Control Center software by double-clicking the
program icon installed on your desktop or on your start menu.
3
Click Open Map File and select a map file.
4
Click Send Map. You can send the map to any of the ten map positions .
Altering Maps Using Software
The values in the map represent a percentage of fuel change over stock. A value
of 10 in the map indicates at that throttle position and RPM range the vehicle
will be 10% richer than stock. If the value is -10, then it would be 10% leaner than
stock. You have the ability to fine tune your fuel curve by altering these values .
The Control Center software allows a value of +250 to -100 in each cell.
www.fuelmotousa.com
2014 Harley Davidson Touring - 5
Download PDF