sglux UV-SENSOR PROBES

sglux UV-SENSOR PROBES
Catalogue
Introduction
The applications of UV sensors are quite varied and therefore the required
sensitivity, environmental endurance, spectral response, field of view and
electronic output interface must be tailored for individual conditions of use.
This publication presents a variety of different standard UV sensors considering
these varying requirements and covering a broad range of industrial UV sensor
applications.
All of the probes are amplified and shielded against electromagnetic interference.
The visible blind sensors are based on a Silicon Carbide (SiC) UV photodiode,
which guarantees highest radiation hardness, long term stability and >1010 visible
blindness (ratio of UV to VIS-IR sensitivity). Blue and GaP type sensors are based
on a Galliumphosphide (GaP) UV photodiode.
Please find an individual four step configuration procedure at page 5 which allows
the prospective user to select among different probe mechanical designs (STEP1),
to select the correct spectral response (STEP 2), to select the different output
types (STEP 3) and to select a sensitivity range (STEP 4).
Usually the sensors are directly connected to the customer’s data bus (via voltage,
current, CAN or USB output). Alternatively, developers and scientists use the sglux
controllers and display modules.
The sglux calibration laboratory offers NIST and PTB traceable calibration
services.
UV Sensor “UV-Surface”
Standard surface-mount 180° FOV UV Sensor
The sensor UV-Surface is a cosine corrected sensor to be used for industrial or scientific UV
radiation measurements of radiation arriving at a surface, horizontal or vertical or any orientation.
On request it is also available in a submersible version. Available calibrated (NIST or PTB
traceable) on request.
Picture
Rev. 4.1
Field of View
Drawing
Manufacturer: sglux GmbH, Max-Planck-Str. 3, D-12489 Berlin, Tel. +49 30 5301 5211, Fax +49 30 5301 5209
mail: welcome@sglux.de - web: www.sglux.de - WEEE No. DE 76297302
page 1
sglux UV-SENSOR PROBES
Catalogue
UV Sensor “UV-Air”
Axis oriented in-chamber UV Sensor
The sensor UV-Air is a cosine corrected axial looking UV sensor with a male thread (M22x1,5) with
many mounting possibilities inside UV radiation chambers. Available calibrated (NIST or PTB
traceable) on request.
Picture
Field of View
UV Sensor “UV-Cosine“
Drawing
Waterproof UV Sensor for outdoor use
The sensor UV-Cosine is an outdoor cosine corrected waterproof sensor (IP68 at window side,
IP65 at plug side, or, on request IP68 for submerge applications). The PTFE housing is stain
repellent. Available calibrated (NIST or PTB traceable) on request.
Picture
Field of View
UV Sensor “UV-Water-G3/4”
Drawing
10 bar water pressure proof UV Sensor
The sensor UV-Water-G3/4 is a waterproof (10 bar or 150 psi) UV sensor to be included into
pressurized water systems (G3/4“ thread). This UV sensor is suited for use in food and beverages
machinery. On request it is also available in a submersible version. Available calibrated (NIST or
PTB traceable) on request.
Picture
Rev. 4.1
Field of View
Drawing
Manufacturer: sglux GmbH, Max-Planck-Str. 3, D-12489 Berlin, Tel. +49 30 5301 5211, Fax +49 30 5301 5209
mail: welcome@sglux.de - web: www.sglux.de - WEEE No. DE 76297302
page 2
sglux UV-SENSOR PROBES
Catalogue
UV Sensor “UV-Water”
10 bar waterprooof UV Sensor
The sensor UV-Water is a waterproof (10 bar or 150ps) UV sensor to be included into pressurized
water systems (G1/4” thread). This UV sensor is suited for use in food and beverages machinery.
On request it is also available in a submersible version. Available calibrated (NIST or PTB
tracelable) on request.
Picture
Field of View
UV Sensor “UV-DVGW”
Drawing
UV Sensor for DVGW certified water purifiers
The sensor UV-DVGW is a special type suitable for use with DVGW certified water purifiers. It
complies with the standard DVGW W294-3(2006). Always delivered calibrated according to DVGW
requirements.
Picture
UV Sensor “UV-Cure”
Field of View
Drawing
Sensor for high UV-Irradiation with integrated temperature sensor
The sensor UV-Cure is an axial looking UV sensor for measurement of high UV radiation at high
temperatures (up to 170°C) in curing and drying processes. It has an integrated temperature sensor
and a diffuser of radiation hard and temperature resistant microporous silica glass. A male thread
(M22x1,5) allows many mounting possibilities inside UV radiation chambers. Available calibrated
(NIST or PTB traceable) on request. Only available with photocurrent output.
Picture
UV Sensor “TOCON-probe”
Field of View
Drawing
Pre-amplified UV Photodetector with housing
The sensor TOCON-probe is a pre-amplified UV Photodiode inside a robust stainless steel M12x1
thread body. It is configured with an integrated sensor connector (Binder 5-Pin plug) and comes
with 2m connector cable. The sensor is easy to mount and connect (only with voltage output
available).
Picture
Rev. 4.1
Field of View
Cable assignment:
Drawing
UV sensor:
white anode, brown cathode
temperature sensor: black, blue
Manufacturer: sglux GmbH, Max-Planck-Str. 3, D-12489 Berlin, Tel. +49 30 5301 5211, Fax +49 30 5301 5209
mail: welcome@sglux.de - web: www.sglux.de - WEEE No. DE 76297302
page 3
sglux UV-SENSOR PROBES
Catalogue
UV Sensor “TOCON-probe”
Pre-amplified UV Photodetector with housing
The sensor TOCON-probe is a pre-amplified UV Photodiode inside a robust stainless steel M12x1
thread body. It is configured with an integrated sensor connector (Binder 5-Pin plug) and comes
with 2m connector cable. The sensor is easy to mount and connect (only with voltage output
available).
Picture
Field of View
UV Sensor “UV-Minilog“
Drawing
UV Datalogger with PC Software
The sensor UV-Minilog is a battery powered UV datalogger with a large internal data storage
(2 million readings). It can log data for up to 18 months without recharging. It is IP67 waterproof and
comes with free PC software. The UV-Minilog can be equipped with all UV sensors to be selected
at STEP 2 and STEP 4 of page 6 configuration guide. Available calibrated (NIST or PTB traceable)
on request.
Picture
Field of View
Drawing
Specifications, valid for all UV Sensors
Fixed Specifications
Configurable Specifications
Parameter
Value
Parameter
Value
Dimensions
Pls. refer to the drawing
Absolute Sensitivity
1nW/cm ! 10W/cm
above.
Temp. Coefficient
0.035%/K analogue sensors
<0.1%/K digital sensors
Spectral Sensitivity
Operating Temp.
-20!+80°C (170°C)
Signal Output
Storage Temp.
-40!+80°C
Connections
Humidity
<80%, non-condensing for
Air versions; 100%
2
2
UV-broadband, UVA, UVB, UVC, UV-Index,
blue light, GaP (blue+visible)
0!5V, 4!20mA, USB, 125kbits CAN bus
2m cable or 5pin male plug;
8Pin plug with 2m cable (digital sensors)
Please find the configuration guide at page 5 of this catalogue.
immersed for submersible
Rev. 4.1
Manufacturer: sglux GmbH, Max-Planck-Str. 3, D-12489 Berlin, Tel. +49 30 5301 5211, Fax +49 30 5301 5209
mail: welcome@sglux.de - web: www.sglux.de - WEEE No. DE 76297302
page 4
sglux UV-SENSOR PROBES
Catalogue
STEP 1 ! Selection of probe mechanical design
Please tick your selection. Please find detailed description of the mechanical design above.
Description
Type
UV-Surface
Standard surface-mount 180° FOV UV Sensor
UV-Air
Standard axias oriented in-chamber UV Sensor
UV-Cosine
Waterproof UV Sensor for outdoor use
UV-Water-G3/4
10 bar water pressure proof UV Sensor with G3/4” thread
UV-Water
10 bar water pressure proof UV Sensor with G1/4” thread
UV-DVGW
UV Sensor for DVGW certified water purifiers
UV-MINILOG
UV Datalogger with PC software
TOCON-probe
Pre-amplified UV photodetector in a M12x1 housing (only with voltage output available)
UV-Cure
Sensor for high UV-Irradiation with integrated temperature sensor (only with photocurrent output)
STEP 2 ! Configuration of the Spectral Sensitivity
Please select one spectral sensitivity curve.
STEP 3 ! Signal Output
Please tick your selection. The pin configuration for analog sensors is shown in the drawings on previous pages.
Connection =
Connection =
Type
Description
“cable”
“male plug”
0!5V
0...5V voltage output proportional to
radiation
input;
supply
voltage
is
7...24VDC, current consumption is <30mA
V0=brown, V+=white,
Out=green,
Shield=black
V0=Pin1=brown
V+=Pin2=black
Out=Pin3=blue
4!20mA
4...20mA current loop for PLC controllers;
the current is proportional to the radiation,
supply voltage is 24VDC
V0=brown, V+= white
V0=Pin1=brown
V+=Pin2=black
USB
The signal is transmitted via USB to a
computer. Software is included.
-----------------------!
Standard USB-A
plug, 1,5m cable
The signal is transmitted via CAN bus
(VSCP protolcol), additional USB
converter for computer use incl. software
available (DIGIBOX)
-----------------------!
Pin a=CAN low
Pin b=CAN high
Pin c=GND
Pin d=Vsupply
CAN bus
STEP 4 ! Sensitivity
2
2
We configure your UV sensor for intensities across 10 orders of magnitude from 1nW/cm to 10W/cm . For good dynamic
behaviour the min and max. intensity at the probe position needs to be known as precisely as possible. Please fill that value,
if known, into the box below. If only a rough estimate is possible, please estimate it in the range selection fields. We will
contact you for further refinement of the range.
2
max. radiation in mW/cm or, if not precisely known, range estimation
max. up to 10"W/cm
Rev. 4.1
2
max. up to 100mW/cm
2
max. up to 10W/cm
Manufacturer: sglux GmbH, Max-Planck-Str. 3, D-12489 Berlin, Tel. +49 30 5301 5211, Fax +49 30 5301 5209
mail: welcome@sglux.de - web: www.sglux.de - WEEE No. DE 76297302
2
page 5
Download PDF