Bluetooth Audio ReceiveR QuicK iNStAll Guide

Bluetooth
Audio
Receiver
QUICK
INSTALL
GUIDE
Model 161091
Thank you for your purchase of the
MANHATTAN Bluetooth Audio
Receiver, Model 161091.
®
Quickly installed with a 3.5 mm
stereo plug, it pairs with PCs, MP3
players, mobile phones and other
Bluetooth-enabled media sources
to convert most speakers into a
wireless entertainment system.
(Instructions on back of this sheet.)
• Built-in rechargeable battery
provides up to 6.5 hours
of listening almost
anywhere
• Compact, integrated
design requires no
external antenna
• Lifetime Warranty
specifications
Standards/Certifications
•CE, QRB
•Bluetooth V 2.1
General
• Streaming format: SBC 48 kHz
• Frequency range: 20 Hz–22 kHz
• Power: built-in rechargeable
lithium-polymer battery with
overcharge protection, (approx.
3 hrs. recharge time; 6.5 hrs.
operating time)
•Power adapter/recharger:
-Input, 100–240 V AC, 50–60
Hz, 0.2 A
-Output, 5.0 V / 0.2 A
-Cable, 97 cm (38 in.)
• Connections: 3.5 mm stereo
(line out); DC 5 V (power in)
• Dimensions: 9 x 8 x 3 cm
(3.5 x 3.15 x 1.2 in.)
• Weight: 122 g (4.3 oz.)
Bluetooth
• Class 2
• A2DP protocol support
• Effective range: up to 20 m
(65.6 ft.)
• 748 kbps data rate
Package Contents
• Bluetooth Audio Receiver
• Power adapter/recharger
• Quick install guide
®
MANHATTAN offers a complete line of PC Components, Peripherals, Cables and
Accessories. Ask your local computer dealer for more information or visit us online at
www.manhattan-products.com
Copyright © MANHATTAN
All products mentioned are trademarks or registered trademarks of their respective owners.
MH-161091-miniQIG-1109-01
setup & Operating instructions
Prior to the initial use of the Bluetooth Audio Receiver, its built-in battery
needs to be fully charged. The first charge can take up to 4 hours, while
subsequent recharging may take less than 3 hours.
Charging the Battery
• Plug the included power adapter/recharger into an AC outlet, then
connect it to the In DC 5V jack on the receiver (above-left image).
• The middle LED (between the On/Off buttons) will light red to indicate
the battery is charging, then turn green to indicate a full charge (above-
right image).
Bluetooth Pairing and Operation
1.Connect your speakers to the 3.5 mm stereo Line Out jack on the
Bluetooth Audio Receiver.
2.Power on the receiver by pressing the On button, and keep it pressed
(for approximately 4 seconds) until the red and blue LEDs (between the
On/Off buttons) flash back and forth. The receiver is now in its pairing
mode. NOTE: Whenever the pairing between devices is not maintained
for a full minute or so, the pairing function will stop and need to be
re-established.
3.Turn on your Bluetooth-enabled device (mobile phone, PC, notebook,
etc.) and activate its Bluetooth pairing per the device’s BT instructions.
NOTE: To play music using a Bluetooth-enabled mobile phone, the
phone needs to support A2DP and AVRCP profiles.
4.When your Bluetooth-enabled device locates the receiver and displays
it (as “BT Speakers”) in its Devices list, select the receiver for pairing.
5.When the display of your Bluetooth-enabled device prompts you to
enter a PIN code, enter 0000 (zeroes). This should complete the
pairing process — indicated by the flashing blue LED — and place the
receiver in standby mode, automatically connecting to your Bluetooth-
enabled device.
6.At this point, the receiver is ready to relay sound to your speakers.
NOTE: To avoid unwanted synching, turn the receiver off when it’s not
in use.
Download PDF