IMC Networks IMCV-S2SM/155 SM1310/Pl-SC+SM1310-/PL-SC

IMC Networks IMCV-S2SM/155 SM1310/Pl-SC+SM1310-/PL-SC
iMcV Fiber Mode Converters
Protocol-Independent, SNMP-Manageable
Fiber Mode Conversion Modules
The iMcV Series of fiber mode conversion modules allow
you to easily extend your network to remote locations by
converting multi-mode fiber to single-mode fiber.
In today’s dynamic networks, changing requirements are a fact of life. The multi-mode
fiber products and cabling which were the most cost-effective and sound choice for your
network yesterday may no longer give you the flexibility you require when adding remote
offices today. Easily overcome the distance limitations inherent to multi-mode fiber by
converting to single-mode fiber. Fiber mode converters are the solution.
Extend the reach of your network without replacing multi-mode fiber equipment:
As an economical alternative to using a switch with single-mode fiber ports, simply install
an IMC Networks fiber mode converter into your multi-mode fiber network. This enables
you to easily connect to single-mode cabling and achieve distances up to 100 km. Our
fiber mode converters also give you the flexibility to add single-mode fiber links only
where needed. The iMcV series of fiber mode conversion modules includes:
iMcV-S2MM:
• Converts multi-mode to single-mode fiber
• Supports 10 Mbps Ethernet to 155 Mbps ATM (OC-3); 622 Mbps; and from
622 Mbps, to 1.0625 Gbps FibreChannel (FC) to 1.25 Gbps Gigabit Ethernet
• Available with fault-tolerance (see below).
iMcV-M2MM:
• Converts multi-mode to multi-mode fiber
• 10 Mbps Ethernet to 155 Mbps ATM (OC-3)
iMcV-S2SM:
• Converts single-mode to single-mode fiber
• Supports 10 Mbps Ethernet to 155 Mbps ATM (OC-3); and from 622 Mbps,
to 1.0625 Gbps FibreChannel (FC) to 1.25 Gbps Gigabit Ethernet
Hot-swappable fiber mode conversion modules significantly reduce operation costs
by allowing other modules within the same chassis to remain up and running during
product upgrades, maintenance and troubleshooting.
The Fault-Tolerant iMcV-FT-S2MM provides a dual data path during operation, the primary link segment is active while the secondary link segment is non-active to prevent an
illegal Ethernet loop. If the primary link segment fails, iMcV-FT-S2MM automatically places
the secondary link segment online and makes the primary link segment non-active. This
allows connected devices to continue to transmit and receive data. Once the primary link
segment is re-established, that link segment will become active once again.
Easily configure and manage converters with the GUI-based iView²:
As an SNMP management application,
iView² gives network managers the ability to monitor and control IMC Networks'
products. iView² runs standalone on
Windows NT/XP/2000, as a standalone
Java Application for other operating systems, as a snap-in module for HP
OpenView, as a Web Server running
under IIS or as a Java Web Servlet.
For assistance in selecting the right
version of iView² for your operating system, please visit our web site at:
Cost-effective and flexible
• Use multi-mode fiber equipment and
implement single-mode fiber only
where longer distances are needed
Protocol-Independent
• Modules support various transmission
speeds— from 10 Mbps Ethernet up
to Gigabit Ethernet
Meets a multitude of installation
requirements
• Available with ST, SC or Small Form
Factor fiber connectors
• Single-strand fiber versions available
• CWDM fiber versions available
• Fault-tolerant versions available
• Supports very long fiber distances
Easy to configure and manage with
GUI-based iView²
• Up and running in less than 5 minutes
• Receive vital traffic and health information, as well as traps if problems
should occur
Maximizes network uptime
• Modules are hot-swappable; no need
to power-down chassis when upgrading or trouble-shooting a single module
http://www.imcnetworks.com/go/iview2
www.imcnetworks.com
800-624-1070
www.mediaconverter.com
Technical Specifications
• Includes protocol-independent operation
• Converts between dissimilar fiber modes and
wavelengths: multi-mode to single-mode; multimode to single-mode; and single-mode to
single-mode
• Ethernet, Fast Ethernet and ATM/OC-3
• OC-12, Gigabit Ethernet and FibreChannel
• 50/125µm or 62.5/125µm multi-mode fiber
• 9/125µm single-mode fiber
• Available for single-strand fiber
• Available with fault-tolerance
Regulatory Approvals:
• Connectors: ST, SC or MT-RJ
Shipping Weight: .30 lbs (.11 kg)
• Installs in any iMediaChassis, iMediaCenter or
MediaChassis
• Supports GUI-Based iView²
• Includes diagnostic LEDs
• Includes hot-swappable architecture
Operating Temperature: 32° to 122°F (0° to +50°C);
5% to 90% (non-condensing), 0 – 10,000 ft. altitude
Storage Temperature: -13° to +158°F (-25° to +70°C);
5 to 90% (non-condensing)
· FCC Class A
· UL/cUL, CSA, CE
Fiber Optics Specifications
For each product listed below in the Ordering Information section, the number in the [XX] denotes an approximate fiber distance based on industry-standard fiber specifications and worst-case (connector loss, aged fiber, splices, etc.) installations. You can typically achieve substantially longer distances.
Actual distances may vary for each installation. For complete power budgets and information on calculating specific distances, please visit web site our at
www.imcnetworks.com/go/fcs or contact IMC Networks Fiber Consulting Services at 949-465-3000.
Ordering Information
iMcV-S2MM/155 — Single-mode to multi-mode
iMcV-S2MM/1250 — Single-strand fiber1 to multi-mode
50-14520
50-14530
50-14530-MT
50-14540
50-14550
50-14555
50-14560
50-14570
50-14580
50-14590
50-14595
59-14808
59-14809
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
SM1310/PLUS-ST + MM1300-ST [40 Km]
SM1310/PLUS-SC + MM1300-SC [40 Km]
SM1310/PLUS-SC + MM1300-MT [40 Km]
SM1310/LONG-ST + MM1300-ST [80 Km]
SM1310/LONG-SC + MM1300-SC [80 Km]
SM1550/LONG-SC + MM1300-SC [100 Km]
SM1310/PLUS-ST + MM850-ST [40 Km]
SM1310/PLUS-SC + MM850-SC [40 Km]
SM1310/LONG-ST + MM850-ST [80 Km]
SM1310/LONG-SC + MM850-SC [80 Km]
SM1550/LONG-SC + MM850-SC [100 Km]
iMcV-S2MM/155 — Single-strand fiber1 to multi-mode
50-14532
50-14533
50-14535
50-14536
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
iMcV-S2MM/155,
SSFX-SM1310-SC + MM1300-SC [20 Km]
SSFX-SM1550-SC + MM1300-SC [20 Km]
SSFX-SM1310/PLUS-SC + MM1300-SC [40 Km]
SSFX-SM1550/PLUS-SC + MM1300-SC [40 Km]
iMcV-S2MM/622 — Single-mode to multi-mode
59-14802
59-14805
iMcV-S2MM/622, MM1300-SC + SM1310/PLUS-SC [40 Km]
iMcV-S2MM/622, MM1300-SC + SM1550/LONG-SC [100 Km]
iMcV-S2MM/1250 — Single-mode to multi-mode
59-14799
59-14800
59-14801
iMcV-S2MM/1250, LX-SM1310-SC + SX-MM850-SC [10 Km]
iMcV-S2MM/1250, LX-SM1310/PLUS-SC + SX-MM850-SC [40 Km]
iMcV-S2MM/1250, LX-SM1550/LONG-SC + SX-MM850-SC [100 Km]
iMcV-M2MM/155 — Multi-mode to multi-mode
50-14510
50-14511
iMcV-M2MM/155, MM1300-ST + MM850-ST [2 Km]
iMcV-M2MM/155, MM1300-SC + MM850-SC [2 Km]
iMcV-S2MM/1250, SSLX-SM1310/PLUS-SC+SX-MM850-SC [40 Km]
iMcV-S2MM/1250, SSLX-SM1550/PLUS-SC+SX-MM850-SC [40 Km]
iMcV-FT-S2MM/1250 — Single-mode to multi-mode
59-14811
59-14812
iMcV-FT-S2MM/1250, 2*LX-SM1310/PLUS-LC + SX-MM850-SC [40 Km]
iMcV-FT-S2MM/1250, 2*LX-SM1550/LONG-LC + SX-MM850-SC [100 Km]
iMcV-S2SM/155 — Single-mode to single-mode
50-14513
iMcV-S2SM/155, SM1550/LONG-SC + SM1310/PLUS-SC [100 Km]
50-14514-LC iMcV-S2SM/155, SM1550/LONG-SC + SM1310/LONG-LC [100 Km]
iMcV-S2SM/155 — Single-strand fiber1 to single-mode
50-14515
iMcV-S2SM/155, SSFX-SM1310-SC + SM1310/PLUS-SC [20 Km]
50-14516
50-14517
50-14518
iMcV-S2SM/155, SSFX-SM1550-SC + SM1310/PLUS-SC [20 Km]
iMcV-S2SM/155, SSFX-SM1310/PLUS-SC + SM1310/LONG-SC [40 Km]
iMcV-S2SM/155, SSFX-SM1550/PLUS-SC + SM1310/LONG-SC [40 Km]
iMcV-S2SM/1250 — Single-mode to single-mode
59-14803
59-14804
iMcV-S2SM/1250, LX-SM1310/PLUS-SC + LX-SM1310/PLUS-SC [40 Km]
iMcV-S2SM/1250, LX-SM1310/PLUS-SC + LX-SM1550/LONG-SC [100 Km]
iMcV-S2SM/1250 — Single-strand fiber1 to single-mode
50-14820
iMcV-S2SM/1250, SSLX-SM1310-SC + SM1310/PLUS-SC
50-14821
50-14822
50-14823
iMcV-S2SM/1250, SSLX-SM1550-SC + SM1310/PLUS-SC
iMcV-S2SM/1250, SSLX-SM1310/PLUS-SC + SM1310/PLUS-SC
iMcV-S2SM/1250, SSLX-SM1550/PLUS-SC + SM1310/PLUS-SC
1
These products have single-strand fiber technology. Deploy in pairs, or connect to another compatible IMC Networks single-strand fiber product. For more information go to:
www.imcnetworks.com/products/SSFX.cfm. Contact IMC Networks for CWDM part numbers.
Related Products — iMcV Series Modules
The iMcV Series includes 10 Mbps (iMcV-PIM), 100 Mbps (iMcV-LIM), autosensing 10/100 Mbps (iMcV-LIM 10/100), 155 Mbps ATM (iMcV-ATM) and Gigabit
Ethernet (iMcV-Gigabit) copper-to-fiber media conversion modules as well as 10/100 and 10/100/1000 switching media converters (MediaLinX series). T1/E1/J1
media converters (iMcV-T1/E1/J1), DS3/E3 media converters (iMcV-DS3/E3) and VDSL to Ethernet media converters (iMcV-VDSL-LANextender) are also available. In addition, IMC Networks has the most extensive line of protocol-independent (iMcV-S2MMs, iMcV-S2SMs and iMcV-M2MMs) fiber mode conversion modules. The iMcV series also includes: iMcV-FiberLinX, iMcV-WDM and iMcV-FiberWay modules. Single-strand fiber versions are available for many of our media
converters.
For more information on the various products in the iMcV Series, please refer to the IMC Networks Web site at: http://www.imcnetworks.com/Products/ProdDir.cfm
IMC Networks
IMC Networks
IMC Networks
IMC Networks
Headquarters
19772 Pauling
Foothill Ranch, CA 92610
TEL: 949-465-3000
FAX: 949-465-3020
[email protected]
www.imcnetworks.com
Europe
Herseltsesteenweg 268
B-3200 Aarschot Belgium
TEL: +32-16-550880
FAX: +32-16-550888
[email protected]
Eastern US/Latin America
18840 US Hwy. 19 North Suite 400
Clearwater, FL 33764
TEL: 727-524-8152/524-8071 (Latin)
FAX: 727-524-8432
[email protected]
Fiber Consulting Services
For information call:
TEL: 949-465-3000
1-800-624-1070 (US/CAN)
+32-16-550880 (Europe)
[email protected]
Copyright © 2005 IMC Networks. All rights
reserved. The information in this document is
subject to change without notice. IMC Networks
assumes no responsibility for any errors that may
appear in this document. Specific product names
may be trademarks or registered trademarks and
are the property of their respective companies.
Document #50-90520 September 2005
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement