Tripod B Series
Tripod Portable Projection Screen
Tripod Screen Parts Identification
USER’S GUIDE
Support beam
Top Hook, Keystone
Eliminator & Screen Handle
Vertical
Extension Bar
Vertical locking sleeve ring
(DOES NOT APPLY TO
136” MODELS)
Carrying handle & Screen height
adjustment lock/release tab
(DOES NOT APPLY TO 136”
MODELS)
Screen Material
End cap
Tripod junction
Screen case
Tripod Support Legs
*136” models see Fig. 4 on next page.
Using the Screen
A. Setting up the screen:
Follow the steps below and Fig. 1 & 2.
1. Place the screen in an upright position (fig.1) with the
legs toward the ground.
2. Deploy the Tripod Support legs by pushing down on
the Tripod Junction.
3. Turn the tripod’s screen casing in a 90-degree
horizontal position so that the screen casing is
nowparallel to the ground with the screen handle facing
the bottom of the top hook.
4. Completely extendthe legs as much as possible so they
are stable and position them away from objects that may
interfere with their balance. DO NOT stand the tripod on
an unstable platform to avoid an injury should the tripod
screen collapse.
Rev. 053116-DR
www.elitescreens.com
1
Fig.1
3
4
2
Fig. 2
1
1
B. Preparing the tripod screen for projection:
Follow the steps below and Fig. 3.
2
1. Pull the screen handle up vertically and hook the screen handle on the Top
Hook.
*Note: Use the Keystone Eliminator to prevent “Keystone Effect” from occurring.
Keystone Effect is caused when a projector presents its image at a downward angle
causing a trapezoid-shaped image to appear on the screen. The Keystone
Eliminator is designed to eliminate that effect by sloping the screen forward.
3
2. Twist the Vertical Locking Sleeve Ring counter-clockwise to unlock the
current position of the Vertical Extension Bar and raise it as necessary to
the desired height.
3. Pull the Screen Height Adjustment Lock/Release tab out (to the left)
located just above the Carrying Handle to raise or lower the bottom of the
screen. Once the desired height has been set, push the tab in to lock the
position in place.
Fig. 3
B. Preparing the tripod screen for projection: (136” models)
Follow the steps below and Fig. 4.
1. Pull the screen handle up vertically and hook the screen handle on the
Top Hook.
2. Twist the top Locking Knob counter-clockwise to unlock the current
position of the Vertical Extension Bar and raise it as necessary to the
desired height and twist back (clockwise) to lock into position.
3. Twist the bottom Locking Knob counter-clockwise to raise or lower
the bottom of the screen. Once the desired height has been set, twist back
(clockwise) to lock into position.
* Note: Due to Tripod design, bottom and top Locking Knobs may not align. To
realign, slightly loosen bottom Locking Knob, carefully spin screen to desired
position, and tighten Locking Knob.
C. Disassembling the screen:
Follow the steps below and Fig. 5.
Fig. 4
1. Unlock the Adjustment Handle by pulling the locking tab to the left or
twist Locking Knob counter-clockwise (136” models only) to unlock and
slowly slide the handle all the way down to bring down the position of the screen’s case.
2. Hold the Extension Bar and twist the Vertical Locking Sleeve Ring or Locking Knob counter-clockwise (136”
models only) to unlock and release the position of the extension bar. Once the extension bar has been brought all the
way down, unhook the screen material from the Top Hook and slowly retract the screen back into the case.
* Note: It is very important to remember to hold the extension bar first and then
unlock the sleeve to prevent the extension bar from slamming and causing injury or
damaging the screen.
3. Turn the screen’s case vertically clockwise and insert the Top Hook’s
bottom pin to lock into the screen’s end cap hole.
4. Close the tripod legs by pushing them in. Lastly, tighten the Vertical
Locking Sleeve Ring/Locking Knob (136” models only) by twisting it
clockwise.
Note:




To ensure the screen is stable, extend the tripod’s legs as much as
possible.
Do not fold the screen or allow any sharp objects to touch the
screen’s surface.
Clean the screen surface often when needed.
Careful use will extend the lifetime of this product.
Rev. 053116-DR
www.elitescreens.com
3
2
1
4
Fig. 5
2
Download PDF