Digital Access Control Keypad(Stainless Steel Panel) Model:YK-368

R
EMC
tested
Germany
Digital Access Control Keypad(Stainless Steel Panel)
Model:YK-368
INTRODUCTION
YK-368 is a digital keypad control station, designed for access control and home security applications.
The control station provides 1 relay output.
YK-368 provides multi-User Codes or single User Code, and provides auto code entry or manual code entry.
YK-368 can be connected with access control system, home security system, can be connected with
door-open buttons.
YK-368 has advanced features with the Micropro cessor and EEPROM non-volatile memory for reliable
performance.
YK-368 is fully keypad programmable, all programming proceed on the keypad.
YK-368 is a device of simple operation, easy to use, reliable functions; it is an ideal device for office,
home and factory in access control and security system installation.
TECHNICAL DATA
Dimensions:
Operating Voltage:
Current Drain:
Relay Output Contacts:
Capacity of Recording:
Weight:
117Hx73Wx40H (mm)
12-24 VAC/DC
Quiescent State=21-27mA, Active State=45-57Ma (1 Relays actuated,
all LED lighted)
N.O. and N.C. Dry Contact, Max Rating of Contact Current 3A/24VDC
250 Codes or 1 Common Code
0.145kg
AUDIBLE & VISIBLE INDICATIONS
Definition of
Audible and
Visible Indications
Status
Indicator STATUS
Output
Indicator
PASS
Amber LED
Green LED Buzzer
Standby mode
1 Flash in 2 Sec interval
Successful key entry
1 Flash then light for 10Sec
(Press # to return to standby
mode)
Successful card / code entry 2 Flashes
Successful operation
2 Flashes
Audible Indicator
1 Beeps
Light
LED
Light for
10Sec
2 Beeps
2 Beeps
Unsuccessful card / code
entry
5 Flashes
5 Beeps
Unsuccessful operation
5 Flashes
5 Beeps
1 Short beep in 10
secretary interval
1 Long beep finish
locking
In locking status
1 Flash in 10 Sec interval
(no response to card / code
entry)
In programming mode
Light
Light
During programming
Light
Continuous
Flash
www.yli.cn
Key Act
Lamp
KEY ACT
We create security
R
EMC
tested
Germany
Programming confirmation
(PRESS KEY #)
Light
Alarm status
Continuous flash
Light
2 Beeps
Continuous beeps
Notice to user: (1)Successful entry, it will keep 10 seconds, if no further key entry in 10 seconds, It will
return to normal operation status(Standby mode).
(2)In case wrong entry, cancel the wrong entry by pressing key #, or waiting for 10 seconds then re-enter.
PROGRAMMING
Before use of the new control station, programming every item to confirm the functions and settings meet
the requirement of the users
Programming code = Management code = Master code
Default programming code is 1234
NOTE: (1) Successful programming operation The amber LED will show 2 flashes and the buzzer will
sound 2 beeps.
Unsuccessful programming operation The amber LED will show 5 flash and buzzer will sound 5 beeps.
(2)The User Number / User ID Card / User Code, are not allowed to record repeatly.Repeat record will not
be entered and will give war ning signal : amber LED 5 flash, buzzer sound 5 beeps to signify rejection. It is
required to delete the old data the re-enter.
PROCEDURES OF PROGRAMMING
(1)Entry into programming
PRESS KEY *
Enter the programming code (4-8 digits, default code is 1234)
# (The amber LED
and green LED lighted, signifying entry into the programming mode)
(2)Recording the new programming code
(For security purpose, change the new programming code from default code before use of the new control
station).
PRESS KEY 0
Enter the new programming code (4-8 digits)
#
Repeat the new programming
code
#
(3)Programming the open-door mode
A.PRESS KEY 3
00
# (Open door by User Card)
(4)Programming the door-open time
PRESS KEY 4
(01-99 seconds)
# (Setting door-opening time 1-99 seconds)
NOTE: Factory setting Door-opening time is 3 seconds
(5)Recording the User Code (Use either A or B)
A. Single User Code (Common User Code)
PRESS KEY 5
00
Enter the User Code (4-8 digits)
#
lDeleting the common User Code
When enter new common User Code the old one will be deleted automatically
B. Multi-User Codes
(Assign a number of any 3 digits as the User Number for each User Code, the User Number is not
allowed to repeat use in the programming, keep the User Number as a record of an user)
PRESS KEY 5
01
Enter the User Number (3 digits)
Enter the User Code (4-8 digits)
# (Confirming the code lengt h) (Green LED flash)
# (Green LED stop flash)(confirmed entering is completed)
NOTE: If continue to record more User Codes, at the end of each recording, it is no necessary to press
the key # per each time, to repeat the above steps until all User Code recordings are finished. Finally
to press the key # to confirm all recording are completed.
Deleting the User Code recorded(Multi-User Codes)
PRESS KEY 5
02
0000
# (Deleted all the User Codes)
PRESS KEY 5
02
Enter the User Code to be deleted
# (Deleted the User Code)
PRESS KEY 5
02
Enter the User Number of the User Code
#(Deleted the User Code of the User
Number)
www.yli.cn
We create security
R
EMC
tested
Germany
(6)Programming User Code entry mode
(User Code entry mode)
PRESS KEY 70
0
# (Manual entry mode, have to press the key # follow the User Code entered to
confirm the code length of the User Code entered. The User Code can be 4-8 digits)
PRESS KEY 70
1
# (Auto entry mode, the User Code must be set in the same code length as the
program code. No need to PRESS KEY # to confirm the code length of the User Code entered. The User
Code can 4-8 digits)
NOTE: Factory setting Manual code entry mode
(7)End of programming
Exit programming mode in 60 seconds
PRESS KEY * to exit programming mode and return to normal operation status (Standby mode)
OPERATION OF THE CONTROL STATION
NOTE: The amber LED 1 flash in 2 second interval-the control station is in normal operation mode,
standby for use.
(1) Open door by User Card
(Door opened by reading User ID Card)
(2) In any case, the door can be opened by entering the programming code (Management code)
SAFETY FUNCTIONS
(1) Entry of 10 false codes or reading 10 invalid ID Cards, the control station locks for 30 seconds.
(2) In case tamper switch is activated, warning signal is indicated: amber LED continuous flash and
buzzer continuous beeps, until tamper switch is deactivated.
Control station in locking state:
No response to ID Card / or key entry, amber LED and green LED show 1 flash and buzzer sounds 1 short
beep in 10 seconds interval, at the end of locking the buzzer sounds 1 long beep to signify the end of locking
and return to normal operation mode.
RESTORING THE DEFAULT PROGRAMMING CODE
If the programming code is lost (or unknown), use the DAP jumper to restore the default programming code,
procedures as follows:
(1)Disconnect power supply.
(2)Put the DAP jumper from OFF position to ON position.
(3)Reconnect power supply, amber LED will flash constantly and the buzzer will beep constantly.
(4)Put the DAP jumper back to OFF position, amber LED will stop flashing, buzzer will stop beep.
(5)The default programming code 1234 is restored.
Note: The restoring operations only restore the default programming code 1234,the recorded Data
or Settings will not be changed or deleted.
NOTICE TO INSTALLER
(1)Around the control station in 50cm distance, there must be no any apparatus with 100 KHZ frequency
sources (In order that no interference is appeared).
(2)In the installation, the distance of 2 control stations, or one control station and other card readers,
should over 50cm.
(3)Do not connect wires with power ON. Before apply power to the control station, should confirm power
voltage is 12VDC and the polarity (+ -) is correct.
To install the back-plate of the control station after pass all performance and function testing.
www.yli.cn
We create security
R
EMC
tested
Germany
WIRING DIAGRAM
(1) The Control Station controls the apparatus Via Power Supply
(2)The Control Station directly controls the connecting apparatus (Note: Max Rating of Relay
Contact Current 3A / 24VDC)
www.yli.cn
We create security
Download PDF