Quick Installation Guide
The following instructions will allow you to set up your LongView easily. Should you require further
assistance, please consult your Installer/User Guide.
Test your LongView before permanently installing your extension cable. The
following instructions apply to both testing and installation of the unit.
LongView is available in versions with and without audio capabilities.
These instructions apply to all versions. Simply ignore instructions to
connect to the audio connectors if your unit does not have audio capability.
1. Power down your computer.
2. Place the Transmitter near the computer. Connect the
Cybex custom cable (marked CUFC) to the 25 pin
INPUT connector on the rear of the Transmitter.
3. Unplug from your computer the peripherals that
you intend to use remotely (keyboard, mouse,
monitor, speakers, microphone and serial device if
applicable).
MAD
E
IN
USA
4. Connect the CUFC cable’s 15 pin video connector to the
video output connector on your PC.
5. If you are using a PS/2 mouse, plug the CUFC cable’s PS/2 mouse connector, designated by a yellow band or mouse icon, into your PC’s PS/2 mouse jack.
If you are using a serial mouse, plug the CUFC cable’s 9 pin serial mouse connector
into your PC’s COM serial port and leave the cable’s PS/2 mouse connector unconnected.
6. Plug the CUFC cable’s remaining 6-pin mini-DIN PS/2 keyboard connector into the PS/
2 keyboard jack on your PC.
7. If you do not use a serial mouse, you
may extend your computer’s serial COM
port for other devices by connecting a
standard 9 pin serial cable (purchased
separately) from the
connector on
the rear of the Transmitter to the COM
serial port on your computer.
If you do use a serial mouse, DO NOT
connect anything to the
connector
on the rear of the Transmitter.
MAD
E
IN
USA
8.
Using standard 3.5mm stereo patch cords, connect the
connector on the rear of the
Transmitter to the speaker or line output jack of your computer and the connector to the
microphone input jack of your PC.
9.
Connect the provided wall-mount power supply to the
jack on the rear of the Transmitter, then plug the power supply into a convenient electrical outlet. Verify that the POWER
light on the front of the Transmitter is lit. (You may connect the power supply to the Receiver
instead of the Transmitter, if you wish.)
10. Plug a standard Category 5 UTP cable (up to 100 meters) into the Remote I/O jack on the
rear of the Transmitter. Cybex C5T or Cybex P5T cable is strongly recommended to achieve
best performance and maximum distance. If using a different Category 5 cable, make sure
it is terminated to the EIA (TIA) 568 B standard, commonly used for 10BaseT Ethernet.
11. Route the Category 5 cable to the location
where you intend to place the monitor, keyboard, mouse and speakers.
12. Place the Receiver near the monitor. Connect your monitor to the jack marked with
the symbol. Connect the keyboard to the
jack. Connect the mouse to the jack.
Finally, connect the speakers and microphone to the
and connectors respectively just as you would connect them to
your PC. Make sure you connect your
monitor and your speakers’ power supply
to appropriate electrical outlets. You must
use speakers with built-in amplifiers for
proper operation.
MA
DE
IN
US
A
13. If you connected the Transmitter for a serial mouse, plug your serial mouse into the
connector on the rear of the Receiver. If you are using a PS/2 mouse and you are extending
your computer’s serial COM port for some other peripheral, plug this peripheral into the
Receiver’s
connector.
14. Connect the Category 5 cable to the remote I/O jack on the rear of the Receiver. Verify that
the POWER light on the front of the Receiver is lit. No power supply is required at the
Receiver. However, you may connect the LongView wall-mount power supply to the Receiver rather than the Transmitter if you wish. If so, verify that the Transmitter’s POWER
light is now lit.
15. Turn on the computer and your monitor and you are ready to go! There are no switches,
jumpers, or other configuration required.
4991 Corporate Drive
Huntsville, Alabama 35805-6201 USA
256-430-4000 (Fax) 256-430-4030
www.cybex.com
Cybex Computer Products International Ltd.
Cybex House, Shannon Free Zone
Shannon, Co. Clare, Ireland
Tel: 00353 61 471 877
Fax: 00353 61 471 871
www.cybex.ie
590-060-001 Rev. B
DAXTEN – Ihr Partner für KVM SERVER MANAGEMENT
DEUTSCHLAND
SPANIEN
IRLAND
Daxten GmbH
Salzufer 16, Geb. B
10587 Berlin
Tel: +49 (0)30 8595 37-0
Fax:+49 (0)30 8595 37-99
info.de@daxten.com
Dakota Computer Solutions S.L.
C/Francisco de Vitoria 19
Entreplanta
50008 Zaragoza
Tel: +34 9 76 210 256
Fax:+34 9 76 219 943
info.es@daxten.com
Daxten Ltd
Unit 5 Distribution Centre
Shannon Free Zone
County Clare
Tel: +353 (0)61 23 4000
Fax:+353 (0)61 23 4099
info.ie@daxten.com
ÖSTERREICH
Daxten
Österreich Ges. m. b. H.
DÄNEMARK
USA
Daxten Österreich Ges. m. b. H.
Künstlergasse 11/4
A-1150 Wien
Tel: +43 (0)1 879 77 65
Fax:+43 (0)1 879 77 65 30
info.at@daxten.com
Daxten
Udviklingsparken
Sønderhøj 46
8260 Viby J
Tel: +45 8734 5610
Fax:+45 8734 5611
info.dk@daxten.com
Daxten LLC
1579 Lexington Road
Green Oaks, IL 60048
Free: (877) 816 1337
Tel: +1 (847) 816 1337
Fax:+1 (847) 816 4558
info.us@daxten.com
GROSSBRITANNIEN
FRANKREICH
Daxten Ltd
4 Harp Business Centre
Apsley Way
London NW2 7LW
Tel: +44 (0)20 8438 3800
Fax:+44 (0)20 8438 3899
info.uk@daxten.com
Daxten
B.P. 04
77, Route de Cheptainville
F-91630 Marolles-en-Hurepoix
Tel: +33 (0)1 64 56 09 33
Fax:+33 (0)1 69 14 88 34
info.fr@daxten.com
Download PDF