art. ahcam608b – ahcam618b ahcam628b – ahcam638b

ART. AHCAM608B – AHCAM618B
AHCAM628B – AHCAM638B
AHD Day & Night cameras,
housing waterproof IP66
Technical specifications:
Image sensor
Lens
Effective picture elements (H x V)
Resolution
Min. illumination (lux)
Electronic shutter (s)
Gamma
IR leds units
IR illumination range (m)
IR filter removal
Video output
Gain control (AGC)
White balance
IP degree protection
Case type/color
Power supply
Current consumption (mA)
Power consumption (W)
Operating temperature
Operating humidity
Dimensions (W x H x D / ø x H mm)
Weight (g)
AHCAM608B
1/2.8" CMOS
Sony
3.6 mm
1920 x 1080
1080p / 2 Mp
0.01 (color) / 0
(B&W, leds IR
ON)
1/25 ÷ 1/50000
0.45
30
25
mechanic
AHD/960H
auto
auto
66
Bullet/dark grey
12 VDC
500
6
-10°C ÷ +55°C
85% max
AHCAM618B
2.8 ÷ 12 mm
1920 x 1080
1080p / 2 Mp
0.01 (color) / 0
(B&W, leds IR
ON)
1/25 ÷ 1/50000
0.45
36
30
mechanic
AHD/960H
auto
auto
66
Bullet/dark grey
12 VDC
500
6
-10°C ÷ +55°C
85% max
AHCAM628B
1/2.8" CMOS
Sony
3.6 mm
1920 x 1080
1080p / 2 Mp
0.01 (color) / 0
(B&W, leds IR
ON)
1/25 ÷ 1/50000
0.45
24
20
mechanic
AHD/960H
auto
auto
66
Minidome/white
12 VDC
400
4.8
-10°C ÷ +55°C
85% max
2.8 ÷ 12 mm
1920 x 1080
1080p / 2 Mp
0.01 (color) / 0
(B&W, leds IR
ON)
1/25 ÷ 1/50000
0.45
36
30
mechanic
AHD/960H
auto
auto
66
Minidome/white
12 VDC
500
6
-10°C ÷ +55°C
85% max
184 x 72 x 70
228 x 97 x 84
94 x 68.5
119 x 82.5
530
530
530
580
1/2.8" CMOS
Specifications are subject to change without notice
Connections:
Adjustments:
BNC
POWER SUPPLY
AHCAM638B
1/2.8" CMOS
For these camera models, the BNC connector video output signal type can be set to AHD or 960H.
Selecting the 960H analogue output allows connection of the camera to a traditional monitor so that adjustments can be
made directly at the installation site. Once these procedures are complete, the AHD output can be selected and the camera
connected to AHD series DVR devices.
Instructions for selecting the BNC connector output signal type for art. AHCAM608B and AHCAM628B are provided below.
960H video signal
1 – while the camera is off, fit the jumper in the selection connector so that the 2 pins are short-circuited
2 – power up the camera
3 – the BNC connector will now be using the 960H analogue video signal
AHD video signal
1 – while the camera is off, make sure the jumper is NOT fitted in the selection connector
2 – power up the camera
3 – the BNC connector will now be using the AHD video signal
Connector with Jumper for
video output signal type
selection
BNC
12 V DC power supply
Instructions for selecting the BNC connector output signal type for art. AHCAM618B and AHCAM638B (valid for cameras
with serial numbers from 1606xxxxx) are provided below.
960H video signal
1 – move the joystick up and hold it for more than 5 seconds
2 – the BNC connector will now be using the 960H analogue video signal
AHD video signal
1 – move the joystick to the left and hold it for more than 5 seconds
2 – the BNC connector will now be using the AHD video signal
Setup:
- Press in the middle the joystick to access the main menu.
- Move the joystick up or down to navigate through the menu.
- Move the joystick left or right to change the values.
- Select the menu EXIT and press in the middle the joystick to end the settings
Download PDF