Z
77-20SR00200220
SR-2DAB
Hi-Fi Table Radio for iPod/iPhone
OWNER’S MANUAL
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
2
< Do not expose this apparatus to drips or splashes.
< Do not place any objects filled with liquids, such as
vases, on the apparatus.
< Do not install this apparatus in a confined space such as
a book case or similar unit.
< The apparatus draws nominal non-operating power
from the AC outlet with its POWER or STANDBY/ON
switch not in the ON position.
< The apparatus should be located close enough to the
AC outlet so that you can easily grasp the power cord
plug at any time.
WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION
< DO NOT REMOVE THE EXTERNAL CASES OR CABINETS
TO EXPOSE THE ELECTRONICS. NO USER SERVICEABLE
PARTS ARE WITHIN.
< IF YOU ARE EXPERIENCING PROBLEMS WITH THIS
PRODUCT, CONTACT TEAC FOR A SERVICE REFERRAL.
DO NOT USE THE PRODUCT UNTIL IT HAS BEEN
REPAIRED.
< The mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.
< Products with Class construction are equipped with a
power supply cord that has a 3-prong grounding plug.
The cord of such a product must be plugged into an AC
outlet that has a protective grounding connection.
< If the product uses batteries (including a battery pack
or installed batteries), they should not be exposed to
sunshine, fire or excessive heat.
< CAUTION for products that use replaceable lithium
batteries: there is danger of explosion if a battery is
replaced with an incorrect type of battery. Replace only
with the same or equivalent type.
< Caution should be taken when using earphones or
headphones with the product because excessive sound
pressure (volume) from earphones or headphones can
cause hearing loss.
CLASS apparatus with double insulation,
and no protective earth provided.
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
iPhone is a trademark of Apple Inc.
“Made for iPod” means that an electronic accessory
has been designed to connect specifically to iPod and
has been certified by the developer to meet Apple
performance standards.
“Works with iPhone” means that an electronic accessory
has been designed to connect specifically to iPhone
and has been certified by the developer to meet Apple
performance standards.
Apple is not responsible for the operation of this device or
its compliance with safety and regulatory standards.
3
Contents
Thank you for choosing TEAC. Read this manual
carefully to get the best performance from this unit.
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Using the Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Battery Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Remote Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Identifying the Parts (Main Unit). . . . . . . . . . . . . . . . . . . . . . . . . . 8
Identifying the Parts (Remote Control Unit). . . . . . . . . . . . . . . 9
Identifying the Parts (Display). . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting the Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Getting Started with an iPod or iPhone. . . . . . . . . . . . . . . . . . 11
Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Listening to an External Source. . . . . . . . . . . . . . . . . . . . . . . . . . 13
Listening to an iPod or iPhone. . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Listening to the DAB Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setting the DAB Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using the DAB Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Preset Tuning (DAB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Before Using the Unit
Read this before attempting any operations.
< Depending on the electromagnetic waves used by a
television broadcast, if a TV is turned on near this unit
while it is also on, lines might appear on the TV screen.
Neither this unit nor the TV are malfunctioning. If you
see such lines, keep this unit well away from the TV set.
< As the unit may become warm during operation, always
leave sufficient space around the unit for ventilation.
< The voltage supplied to the unit should match the
voltage as printed on the rear panel. If you are in any
doubt regarding this matter, consult an electrician.
< Choose the installation location of your unit carefully.
Avoid placing it in direct sunlight or close to a source of
heat. Also avoid locations that are subject to vibration,
excessive dust, heat, cold or moisture.
< Do not place the unit on an amplifier or receiver.
< Do not open the cabinet because this might result in
damage to the circuitry or electrical shock. If a foreign
object should get into the unit, contact your dealer or
service company.
< When removing the power plug from the wall socket,
always pull directly on the plug. Never pull the cord.
< Do not attempt to clean the unit with chemical solvents
as this might damage the finish. Use a clean cloth that is
dry or slightly damp.
< Keep this manual in a safe place for future reference.
Listening to the FM Radio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Preset Tuning (FM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
RDS (Radio Data System). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Maintenance
If the surface of the unit gets dirty, wipe with a soft cloth or
use a diluted mild liquid soap. Be sure to remove any excess
liquid completely. Do not use thinner, benzine or alcohol
as they might damage the surface of the unit. Allow the
surface of the unit to dry completely before using it.
Beware of condensation
When the unit is moved from a cold to a warm place, or
used after a sudden temperature change, there is a danger
of condensation. Vapour in the air could condense on
internal mechanisms, making correct operation erratic or
impossible. To prevent this, or if this occurs, leave the unit
for one or two hours with the power turned on. The unit
will stabilize at the temperature of its surroundings.
4
Battery Precautions
Remote Control Unit
< Be sure to insert the batteries with correct positive “+”
and negative “_” polarities.
The included remote control unit allows the unit to be
operated from a distance.
When using the remote control, point it towards the
remote sensor on the front of the unit.
< Use batteries of the same type. Never use different
types of batteries together.
< Either rechargeable or non-rechargeable batteries can
be used. Refer to the precautions on their labels.
< When the remote control unit is not to be used for a
long time (more than a month), remove the battery
from the remote control unit to prevent it from leaking.
< If the batteries leak, wipe away the leakage inside the
battery compartment and replace the batteries with
new ones.
< Do not use any batteries other than those specified. Do
not mix new batteries with old ones.
< Even if the remote control is used within its effective
operation range (5 m), the unit might not respond to
the remote if there are any obstacles between them.
< The remote control might function incorrectly if it is
operated near other products that generate infrared
rays or if other remote control devices that use infrared
rays are operated near the unit. Likewise, the other
products might also function incorrectly.
Battery installation
1. Remove the battery compartment cover.
< Do not heat or disassemble batteries. Never throw them
in fire or water.
< Do not carry or store batteries with other metallic
objects. Doing so could cause batteries to short circuit,
leak or explode.
2. Put in the lithium battery (CR2032, 3 V).
< Never recharge a battery unless it is confirmed to be a
rechargeable type.
3. Close the cover.
Battery replacement
If the distance to the unit from which the remote control
can be used decreases, the battery is losing its charge. In
this case replace the battery with a new one.
< For information about the collection of batteries, please
contact your local municipality, your waste disposal
service or the place where you purchased them.
5
Connections
CAUTION:
< Turn off the power (set to standby) before making connections.
< Read the instructions of each device you intend to use with this unit.
< Be sure to connect each plug securely. To prevent hum and noise, do not bundle the connection cords.
C
A
AC wall
socket
B
F
D
VIDEO
IN
Monitor/TV
6
E
A AC Power Cord
Be sure to connect the power cord to an AC socket
that supplies the correct voltage.
If the power cord is unplugged and the batteries for
the backup are exhausted, settings for the clock, timer
and radio station presets will be lost.
E Battery compartment
The batteries supply backup power to the built-in
clock and memory when the unit is temporarily
disconnected from an AC socket.
Battery installation
B PHONES
To listen with headphones, first lower the volume
level to the minimum. Then, connect the headphones
plug into the PHONES jack, and adjust the volume by
turning the VOLUME knob.
The speakers will make no sound when headphones
are plugged in.
Caution:
Do not turn the unit on or off, or connect or
disconnect headphones from this jack while
wearing headphones. Very loud sound could be
output from the headphones.
AVOID DAMAGING YOUR HEARING - Do not put
on headphones until after plugging them in.
C AUX IN
You can connect a portable audio player to this jack
(page 13).
D VIDEO OUT
This terminal outputs the video signal from a
connected iPod/iPhone.
Use the supplied RCA (pin) W@ mini-plug video cable
to connect this to the composite video connector of a
television or monitor.
Make the following settings on your iPod/iPhone’s
menu to output video to a TV via the Dock.
In the [Video] menu, select [Video Settings], and
then set [TV OUT] to [On] or [Ask].
< When you have set [TV OUT] to [Ask], each time
you play a video your iPod/iPhone prompts you
to specify whether to output it to a TV.
< When you output video to a TV from your iPod/
iPhone, the video is not displayed on the iPod/
iPhone’s screen.
iPod touch* and iPhone models do not have
this menu. You must specify whether to output
video to a TV each time you play it.
1. Slide down to remove the cover.
2. Insert two commercially-available AAA alkaline
batteries.
3. Replace the cover.
Battery replacement
If the clock starts to show the wrong time when
the unit is disconnected from AC power, replace the
batteries with new ones.
< For information about the collection of batteries,
please contact your local municipality, your waste
disposal service or the place where you purchased
them.
Note:
Alkaline bateries should be used.
F DAB/FM antenna
Extend the antenna into a “T” shape, find the best
position for reception and attach it to a window frame
or wall with thumbtacks or the like. This antenna may
need to be repositioned if you move your unit to a
new location.
< For DAB reception, you can check the antenna
adjustment or positioning for the best reception by
viewing the signal strength on the display (page 19).
* iPod touch 1st generation: Software ver. 2.2 or
later
7
Identifying the Parts (Main Unit)
B
C
D
E
F
G
A
A
Q P
O N M L K
A Speakers (Stereo)
B VOLUME
Use this knob to adjust the volume level.
C STANDBY/ON ( )
Use this button to turn the unit on or put it in standby.
D FUNCTION
Use this button to select the source you want to listen to.
E Dock
Before use, insert an appropriate Dock Adapter in the
Dock, and then insert an iPod/iPhone (page 11).
F SELECT
In iPod mode, use this button to confirm a selection in a
menu. This button has the same functions as the Center
button of the Click Wheel of an iPod.
In DAB mode, use this button to confirm selections in
menus.
G TUNING/MULTI JOG
Use this knob to tune in a station.
Use this knob also to select setting values.
H Remote sensor
When operating the remote control unit, point it
towards here.
I ALARM 1, ALARM 2
Hold down these buttons for more than 2 seconds to
enter the timer setting mode.
These buttons are also used to turn the timer function
on and off.
J MEMORY/CLOCK ADJ
8
In tuner mode, use this button to store preset channels
into memory.
In standby mode, use this button to enter clock
adjustment mode.
J
I H
K Skip/Search (.//)
PRESET (‡/°)
In iPod mode, use these buttons to skip to songs. Hold
down these buttons to search for a part of a song.
In tuner mode, use these buttons to select a preset
station.
L Display
M SNOOZE/DIMMER
After the TIMER ON time is reached, use this button to
turn the unit off for 6 minutes.
Use this button also to dim the display.
N Play/Pause (y/J)/DISPLAY
In iPod mode, use this button to start or pause
playback.
In DAB mode, use this button to access various features.
O SHUFFLE/RDS/INFO
In iPod mode, use this button to start shuffle playback.
In FM mode, use this button to select an RDS mode.
In DAB mode, use this button to choose the type of
information displayed.
P REPEAT/AUTO SCAN
In iPod mode, use this button to set the repeat function.
In DAB mode, press this button to automatically locate
all available DAB services. Press once for UK services, or
hold for longer than 2 seconds to activate international
search.
Q SLEEP
Use this button to set the sleep timer.
Identifying the Parts (Remote Control Unit)
G Skip/Search (.//)
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
In iPod mode, use these buttons to skip to songs. Hold
down these buttons to search for a part of a song.
In DAB mode, use these buttons to select a station.
In FM mode, use this button to tune in a station.
H TREBLE
Use this button to start treble level adjustment.
I BASS
Use this button to start bass level adjustment.
P
Q
R
J MEMORY/CLOCK ADJ
In TUNER mode, use this button to store preset channels
into memory.
Use this button also to adjust the clock.
K FM MODE
In FM mode, use this button to select stereo or
monaural.
L FUNCTION
Use this button to select the source you want to listen to.
A STANDBY/ON ( )
Use this button to turn the unit on or put it into
standby.
B ALARM 1, ALARM 2
Hold down these buttons for more than 2 seconds to
enter the timer setting mode.
These buttons are also used to turn the timer function
on and off.
C SHUFFLE/RDS/INFO
In iPod mode, use this button to start shuffle playback.
In FM mode, use this button to select an RDS mode.
In DAB mode, use this button to choose the type of
information displayed.
D REPEAT/AUTO SCAN
In iPod mode, use this button to set the repeat function.
In DAB mode, press this button to automatically locate
all available DAB services. Press once for UK services, or
hold for longer than 2 seconds to activate international
search.
In FM mode, use this button to start automatic tuning.
E PRESET/SCROLL (‡/°)
In iPod mode, use these buttons to scroll up and down
in a menu. These buttons have the same functions as
the Click Wheel of an iPod.
In TUNER mode, use these buttons to select a preset
station.
F Play/Pause (y/J)
In iPod mode, use this button to start or pause
playback.
M SLEEP
Use this button to set the sleep timer.
N MENU/DISPLAY
In iPod mode, use this button to go back to the previous
menu. This button has the same functions as its iPod
counterpart.
In DAB mode, use this button to access various features.
O SELECT
In iPod mode, use this button to confirm a selection in a
menu. This button has the same functions as the Center
button of the Click Wheel of iPod.
In DAB mode, use this button to confirm selection in
menus.
P VOLUME (–/+)
Press the + and – buttons to adjust the volume level.
Q MUTING ( )
Use this button to mute the sound.
R DIMMER (
)
Use this button to change the brightness of the front
panel display and buttons.
Note:
To simplify explanations, instructions in this manual usually
only refer to the names of the buttons and controls on
the front panel. Associated controls on the remote control
operate similarly.
9
Identifying the Parts (Display)
A
B
C
D
Setting the Clock
E
Adjust the clock before attempting any operations.
1 If the unit is on, press the STANDBY/ON button
to put it in standby.
F
2 Press and hold the CLOCK ADJ button for more
than 3 seconds.
A When the unit is on, one of these indicators lights to
Hold down
more than 3sec.
show the current sound source.
B Lights when a stereo FM broadcast is tuned in stereo
mode.
C Shows the digital clock or timer on/off time.
“24 HR” or “12 HR” blinks on the display.
D Lights when the sleep timer is active.
If you want to change the hour mode (12-hour or
24-hour), turn the MULTI JOG.
E Lights when the wake up timer is active.
F Shows the current source, date, frequency, volume,
muting status, preset channel, etc.
< You can also use the Skip buttons (.//) on the
remote control unit instead of the MULTI JOG.
< If no button is pressed for 10 seconds, timer setting
mode ends.
3 Press the CLOCK ADJ button again.
The “hour” value blinks.
4 Turn the MULTI JOG to set the current hour, and
then press the CLOCK ADJ button.
The “minute” value blinks.
5 Repeat step
10
4 to set “minute”, “year”, “month”
and “day”.
After “day” is set, the clock starts.
Getting Started with an iPod or iPhone
To play your iPod/iPhone through the SR-2DAB, you must
first insert the adapter for your model of iPod/iPhone.
1 Select the Dock Adapter that fits your iPod/
iPhone.
“nano” for 1st and 2nd generation iPod nanos.
“iPhone/Classic 160GB” for iPhones and 160 GB
iPod Classic models.
Compatible iPod/iPhone Software
If your iPod/iPhone will not work with the SR-2DAB or with
the remote control unit, a software update might solve the
problem.
Visit the Apple website and download the latest iPod/
iPhone software.
http://www.apple.com/ipod/download/
“20GB + U2” for 20 GB iPods with Click Wheels, U2
Special Edition iPods, 30 GB iPods with video and
80 GB iPod Classic models.
“60GB (color) + Photo 40GB/60GB” for 40 GB
iPods with Click Wheels, iPods with color displays,
60 GB iPods with video and 160 GB iPod Classic
models.
< Use the adapter supplied with the iPod/iPhone or a
commercially available one to use other iPod/iPhone
types.
2 Insert the adapter into the SR-2DAB dock.
Fit the front edge of the adapter into the dock, and
then press the back edge of the adapter into the
Dock until a “click” is heard indicating that the adapter
is inserted correctly.
1
2
< To remove the adapter, hold its left and right sides
and gently pull it up.
11
Basic Operation
1 Press the STANDBY/ON button to turn the unit
on.
< The unit turns on with the source that was last
selected.
< If an iPod/iPhone that is in playback mode is inserted
into the Dock, the SR-2DAB will automatically turn on
and start iPod/iPhone playback.
2 Press the FUNCTION button to select a source.
Dimmer
You can change the brightness of the front panel display
and buttons.
Use the DIMMER button to set the brightness to one of
three levels or turn the light off.
This function works even if the unit is in standby.
< Setting is ended if the STANDBY/ON button is pressed.
Muting
You can mute the sound temporarily.
< To listen to an external source connected to the AUX
IN jack, select AUX.
< If you select “iPod” when no iPod/iPhone is docked,
the iPod indicator on the display blinks.
3 Play the source, and adjust the volume using
the VOLUME knob.
The volume can be adjusted from MIN (0) to MAX (40).
12
To mute the sound, press the MUTING button.
Press the MUTING button again to unmute the sound.
< “MUTING” appears on the display while muting is
engaged.
< If you change the volume or source when the sound is
muted, it will be unmuted.
Listening to an External Source
Adjusting the bass and treble
You can adjust the bass and treble between “–5” and “+5”.
In addition to connecting other audio devices, you can use
the AUX IN to listen to an iPod that has no dock connector
or when an appropriate Dock Adapter is not available.
1 Connect the PHONES jack (audio output jack) of
a portable audio player to the AUX IN jack of
the SR-2DAB using the supplied stereo mini
plug cable.
2 Select “AUX” using the FUNCTION button.
Press the BASS or TREBLE button, and then, within 5
seconds, press the volume buttons (– or +) to adjust the
bass or treble level .
3 Play the source, and adjust the volume of both
the SR-2DAB and the connected audio device.
When using the headphones jack of a device, if you
do not adjust its volume, you might not hear any
sound from the SR-2DAB.
< Turning the volume of the connected device up too
high might cause the sound from your SR-2DAB to
be distorted. In this case, reduce the volume of the
device until the distortion stops and then adjust
the volume level of the SR-2DAB to a comfortable
listening level.
13
Listening to an iPod or iPhone (1)
1 Insert the iPod/iPhone into the SR-2DAB dock.
2 Then press the Play/Pause button (y/J) on the
iPod/iPhone or the SR-2DAB.
The SR-2DAB will automatically turn on and start
playback from the iPod/iPhone’s song list.
< If an iPod/iPhone that is in playback mode is inserted
into the dock, the SR-2DAB will automatically turn on
and playback sound will be heard from the speakers.
Selecting iPod mode
Select “iPod” using the FUNCTION button. If an iPod/
iPhone is already docked, playback will start.
If no iPod/iPhone is docked, the iPod indicator on the
display blinks.
Stopping playback temporarily
(pause mode)
< Make sure to use a suitable Dock Adapter (page 11).
< The battery of an iPod/iPhone will be recharged until
it is full whenever the iPod/iPhone is docked and the
SR-2DAB is connected to AC power.
< If headphones are also plugged into the iPod/iPhone,
sound comes from both the headphones and the
SR-2DAB speakers.
Note for iPod Touch/iPhone
If an iPod touch/iPhone that is in video playback
mode is inserted into the dock while the SR-2DAB
is in the standby mode, the SR-2DAB is not turned
on.
If you want to hear the sound of video from an
iPod touch or iPhone, connect the iPod touch/
iPhone to the Dock first, and then operate the
SR-2DAB and iPod/iPhone.
< The SR-2DAB might turn on when you play data
for which the audio signal is output earlier than
the video signal.
14
Press the Play/Pause button (G/J) during playback to
stop playback at the current position.
To resume playback, press the Play/Pause button (G/J)
again.
< You can also use the button on the iPod to pause
playback.
Searching for a part of a song
Hold down
more than 2sec.
During playback, hold down a Search but ton
(. or /) for more than 2 seconds to search a song.
Release it when you find the part you want to hear.
Returning to the previous iPod menu
Press the MENU button. This button has the same
functions as its iPod/iPhone counterpart.
Selecting a menu item
Skipping to an earlier or later song
During playback , press the Skip but tons
(.//) repeatedly until you find the desired song.
The selected song will be played from the beginning.
< If the . button is pressed once during playback, the
song currently being played will be played from the
beginning. To return to the beginning of the previous
song, press the . button twice.
Press the SCROLL buttons (‡/°) to scroll to the menu
item you want, and then press the SELECT button.
15
Listening to an iPod or iPhone (2)
Activating the repeat mode
During playback, press the REPEAT button to change
the repeat mode.
Each time the REPEAT button is pressed, the iPod
REPEAT setting changes as follows:
REPEAT ONE
REPEAT ALL
(off)
< If you select “REPEAT ONE” to play only one song, the
repeat once icon (
) appears on the iPod/iPhone’s
display.
< If you select “REPEAT ALL” to play all songs, the repeat
icon ( ) appears on the iPod/iPhone’s display.
Activating the shuffle mode
During playback, press the SHUFFLE button to change
the shuffle mode.
Each time the SHUFFLE button is pressed, the iPod
SHUFFLE setting changes as follows:
SONG
ALBUM
(off)
< If you select “SONG”, the iPod/iPhone shuffles songs
within the list you choose to play.
< If you select “ALBUM”, the iPod/iPhone plays all the
songs on an album in order, and then randomly selects
another album in the list and plays through it in order.
< During shuffle playback, the shuffle icon (
on the iPod/iPhone’s display.
16
) appears
Listening to the DAB Radio
When the unit is switched to DAB mode for the first
time, the automatic tuning process will start and create a
channel list. (Autoscan local: 11B to 12D)
3 When you find the channel, press the SELECT
button.
< After the first time, when the unit is switched to DAB
mode, the last station listened to will be tuned in again.
1 Press the FUNCTION button to select “DAB”.
< If you do not press the SELECT button within
10 seconds, the display will return to the currently
tuned station.
< If you move the unit to a new area or you want to
check to see if there are new channels available
in your area, you can scan to find new channels
automatically by using the automatic scanning
function.
< If no broadcast services are found, “NO STATIONS
AVAILABLE” is displayed and the unit will automatically
enter manual tuning mode (page 20).
Auto scan
You can scan DAB bands to find new channels.
Local scan: 11B to 12D
Press the AUTO SCAN button while DAB is selected as
the source.
When the scanning process has finished, the DLS
(Dynamic Label Segment) (page 18) appears on the
second line of the display.
2 Turn the TUNING knob to select the station you
want to listen to.
Full scan: 5A to 13F
If you want to search stations internationally, press and
hold the AUTO SCAN button for longer than 2 seconds
while DAB is selected as the source. Try this if “Local
Scan” does not find the channels you want.
Hold down
more than 2sec.
Currently tuned station
< You can also select and activate “Local scan” and “Full
scan” in the DAB function control menu (page 20).
17
Setting the DAB Display
You can choose the type of information displayed in the
second line of the display while listening to DAB.
1 In DAB mode, press the INFO button.
DLS
The Dynamic Label Segment (DLS) is a scrolling text label
supplied by the radio station. It may be information about
music titles or details regarding the programme or station.
Programme type
This is a description of the type of music broadcast by the
radio station such as Pop, Rock or Classical music.
The DLS (Dynamic Label Segment) appears on the
second line of the display.
2 Turn the TUNING knob.
Ensemble name
This displays the name of the enesemble that is
broadcasting the programme.
Date and time
This displays the current date and time.
The information shown changes as follows.
DLS (Dynamic Label Segment)
Programme type
Ensemble name
Date and time
Channel and frequency
Bitrate
Signal error rate
18
DAB CT (Clock Time) mode
The CT data is supplied by the DAB station and should
always be accurate. When you set the DAB CT mode
to on, the clock setting of the SR-2DAB will be adjusted
automatically according to this data. Therefore, if you
tune in a DAB station that is broadcasting incorrect CT
data, the clock might be innacurately adjusted, and that
could eventually affect timer operation.
< The DAB CT mode is set to off in the factory default
setting.
Turning the DAB CT mode on or off
1. In DAB mode, press and hold the INFO button for
more than 2 seconds.
The DAB CT menu appears.
2. Turn the MULTI JOG to select on or off.
Using the DAB Menu (1)
Channel and frequency
This displays the channel and frequency of the currently
playing broadcast.
In DAB mode, use the DAB menu to access various
functions.
Opening the DAB menu
In DAB mode, press the DISPLAY button.
Bitrate
The bitrate and sound mode of the broadcast currently
being received is displayed.
Signal error rate
This displays the digital bit error rate (0-100) of the currently
tuned channel. The lower the figure the better the quality
of the received broadcast.
Selecting the menu item
Turn the TUNING knob to find the desired menu item
and then press the SELECT button.
Signal strength display
You can check the signal strength of the current station.
The options change as follows.
Local scan
Full scan
Manual tune
In DAB mode, press the SELECT button.
DRC
Station order
Main menu
The signal strength indicator appears.
< To return to the standard display, press the FUNCTION
button to select “DAB” again or press the INFO button.
In addition, if the unit is put into standby mode by
pushing the STANDBY/ON button, the standard display
will reappear the next time that the power is turned on.
19
Using the DAB Menu (2)
Local scan (Auto scan)
The unit will scan the DAB bands between 11B to 12D and
add the channels found to the channel list.
1 In DAB menu mode, select “Local scan” (page 19).
< You can also activate the “Full scan” by using the AUTO
SCAN button (page 17).
Manual tune
2 Press the SELECT button.
This option allows you to manually tune in a channel and
view a continuously updated indication of the strength
of the signal. This could be useful when adjusting or
positioning an antenna for better reception.
1 In
DAB menu mode, select “Manual tune”
(page 19).
2 Press the SELECT button.
< You can also activate the “Local scan” by using the
AUTO SCAN button (page 17).
Full scan (Auto scan)
The unit will scan all the DAB bands between 5A to 13F
and add the channels found to the channel list. Try this If
you want to search stations internationally or if “Local Scan”
does not find the channels you want.
3 Turn the TUNING knob to select the station you
want to listen to.
1 In DAB menu mode, select “Full scan” (page 19).
2 Press the SELECT button.
Currently tuned station
20
4 When you find the channel, press the SELECT
button.
3 Turn the MULTI JOG to select the desired level
of DRC and then press the SELECT button.
The signal strength indicator appears.
5 While
viewing t he indicator, adjust or
reposition the antenna until the best reception
is indicated.
6 Press the SELECT button to cancel manual tune
and resume normal reception.
You can apply one of three DRC values.
0: DRC off
0.5: DRC low
1: DRC high
DRC
Use this option to set the Dynamic Range Control (DRC)
value to be applied to received broadcasts. DRC is used to
reduce the range between high and low volumes of audio
and is sometimes applied at the broadcast source. Pop
music might have a high value of DRC applied, appropriate
for constantly high listening levels, while classical music
broadcasts might have no DRC applied to allow the listener
to hear the full dynamic range of the source volume.
1
In DAB menu mode, select “DRC” (page 19).
< The current value is marked with a “*”.
Station order
You can select the order in which stations are listed.
2 Press the SELECT button.
1 In DAB menu mode, select “Station order”
(page 19).
2 Press the SELECT button.
Current value mark
The DRC value appears.
21
Using the DAB Menu (3)
Current setting mark
Main menu
You can check the DAB software version and initialize the
DAB settings.
The setting option appears.
1 In
DAB menu mode, select “Main menu”
(page 19).
3 Turn the MULTI JOG to select the desired option
and then press the SELECT button.
2 Press the SELECT button.
You can choose one of three station orders.
Alphanumeric
Channels are listed alphabetically by the
letters in the channel name.
Ensemble
Channels are listed by ensemble name.
Valid
This option will list active stations at the
top of the channel list, and channels that
are in the list but have no service in your
area at the end.
SW version (Software version)
Press the SELECT button again.
The version number of the installed software is
displayed.
< The current setting is marked with a “*”.
22
< This option shows the version number of the
installed software. This is for information only and no
adjustment is possible.
Preset Tuning (DAB)
Factory reset
Turn the MULTI JOG to select “Factory reset”, then
press the SELECT button.
You can programme 30 DAB channel presets.
1 Select
a DAB station you want to store
(page 17).
2 Select a preset channel to store the station
using the PRESET buttons (‡/°).
< You can also use the PRESET buttons (.//) on
the main unit.
3 Press and hold the MEMORY button for more
than 2 seconds.
A confirmation screen appears. If you are certain
that you want to initialize the DAB settings, press the
SELECT button again.
Hold down
more than 2sec.
The station is stored.
To store more stations, repeat steps 1 to 3 .
How to select a preset station
All DAB settings are cleared and the auto scan process
will start immediately.
In DAB mode, press the PRESET buttons (‡ /° )
repeatedly until the desired preset station is found.
< You can also use the PRESET buttons (.//) on the
main unit.
23
Listening to the FM Radio
1 Press the FUNCTION button to select “FM”.
When a station is tuned in, the tuning process will
stop automatically. Repeat this step until you find the
station that you want to hear.
<After you tune in a station using the automatic
tuning, it is received in Mono mode. To switch to
Stereo mode, press the FM MODE button on the
remote control unit.
2 Select the station you want to listen to.
Manual tuning
Turn the TUNING knob until you find the station that
you want to hear.
FM MODE button
Pressing this button alternates between Stereo mode
and Mono mode.
Stereo
FM stereo broadcasts are received in stereo and ST
indicator ( ) appears in the display.
Automatic tuning
Press the AUTO SCAN button to begin automatic
tuning.
< If the sound is distorted and ST indicator ( ) blinks, the
signal is not strong enough for good stereo reception.
In this case, change to Mono mode.
Mono
To compensate for weak FM stereo reception, select
this mode. Reception will now be forced into monaural,
reducing unwanted noise.
If the reception is poor
<To scan a higher frequency station, turn the TUNING
knob in the "UP" direction and press the AUTO SCAN
button. To scan a lower freqency station, turn the
TUNING knob in the "DOWN" direction and press the
AUTO SCAN button.
24
Extend and turn the DAB/FM antenna to improve the
reception of a station.
Preset Tuning (FM)
You can programme 30 FM channel presets.
Saving presets automatically
Saving presets manually
1 Tune in a station you want to store (page 24).
2 Select a preset for storing the station using the
Hold down
more than 2sec.
PRESET buttons (‡/°).
Press and hold the AUTO SCAN button for more than
2 seconds.
Up to 30 stations in your area will be stored
automatically. If there are more than 30, those with the
best reception are stored.
< You can also use the PRESET buttons (.//) on
the main unit.
How to select a preset station
3 Press and hold the MEMORY button for more
than 2 seconds.
Hold down
more than 2sec.
In FM mode, press the PRESET buttons (‡ /° )
repeatedly until the desired preset station is found.
To store more stations, repeat steps 1 to 3 .
< You can also use the PRESET buttons (.//) on the
main unit.
25
RDS (Radio Data System)
The Radio Data System (RDS) is a broadcasting service that
allows stations to send additional information along with
the regular radio programme signal.
PTY (Programme Type)
When you select PTY, the programme type will be
displayed.
If there is no PTY data, “NO PTY” will be displayed.
1 Tune in an FM RDS station (page 24).
The clock time appears on the display.
2 Press the RDS button.
RT (Radio Text)
When you select RT, the news of stations composed of
up to 64 symbols will be displayed.
If there is no RT data, “NO RT” will be displayed.
CT (Clock Time)
This displays the current date and time.
Each press of the RDS button changes the RDS mode
as follows:
PTY (Programme Type)
RT (Radio Text)
CT (Clock Time)
Frequency
26
Frequency
This displays the channel and frequency of the currently
playing broadcast.
Timer (1)
Sleep timer
Wake up timer
You can set the sleep timer so that the unit turns itself off
after a specified amount of time.
You can set the unit to turn on and off at specific times. You
can set two separate timers with ALARM 1 and ALARM 2.
< Adjust the clock before setting the timer (page 10).
Setting the wake up timer
The procedures below are to set ALARM 1.
Follow similar steps to set ALARM 2.
1 Press and hold the ALARM 1 button for more
than 2 seconds.
The sleep indicator (
) appears on the display.
Each press of the SLEEP button cycles through timer
options (from 90 down to 15 minutes). The unit will
automatically stop playback and enter Standby mode
when the time elapses.
Hold down
more than 2sec.
90
OFF
………
75
15
“ON TIME” appears on the display.
The clock hour value and the wake up timer
indicator ( ) blink.
< If no button is pressed for about 10 seconds, timer
setting mode will be exited.
2 Turn the MULTI JOG to set the hour, and then
press the ALARM 1 button.
< If you want to check the time remaining until the unit
switches to standby, press the SLEEP button once to
display the remaining time for a few seconds.
< The display is dimmed when the sleep timer is
activated.
The clock minutes value blinks.
< You can also use the Skip buttons (.//) on the
main unit instead of the MULTI JOG.
27
Timer (2)
3 Turn the MULTI JOG to set the minute, and then
6 Turn the MULTI JOG to set the volume, and then
The time when the timer will turn on has been set.
“OFF TIME” appears and the clock hour value blinks
on the display.
The volume for timer operation can be adjusted from
10 to MAX (40).
press the ALARM 1 button.
press the ALARM 1 button.
The wake up timer indicator ( ) stops blinking.
4 Repeat steps
2 and 3 to set the timer's off
time.
The time when the timer will turn off has been set.
“SOURCE” appears and the source name blinks on
the display.
5 Turn the MULTI JOG to select a source (iPod,
7 Prepare the source.
If the source is set to “iPod”, insert an iPod/iPhone.
If the source is set to “TUNER”, tune in a station.
8 Press the STANDBY/ON button to put the unit in
standby.
DAB, FM or buzzer), and then press the ALARM 1
button.
Put the unit in standby, or the wake up timer
will not work.
However, even when the unit is not in standby, if
the wake up timer has been set the unit will turn off
(enter standby) when the off time is reached.
< “AUX” cannot be selected.
“VOLUME” appears and its value blinks.
< The playback volume will gradually increase to the
set volume when the unit is turned on by the wake
up timer.
< If the source is set to “iPod” but no iPod/iPhone is set,
the buzzer will sound instead.
< If the source is set to “TUNER” and the unit turns on, it
will tune in the station that was last selected.
28
Turning the wake up timer on and off and
checking timer settings
Using the snooze function
Press the ALARM 1 or ALARM 2 button briefly to turn
the timer on/off and check timer setting details.
After the ON time is reached, press the SNOOZE button
to turn the unit off temporarily for 6 minutes. After this
time it will turn on again.
You can use this function repeatedly for up to 1 hour.
x
Wake up timer is turned on,
and the ON TIME is shown
x
Wake up timer stays on,
and the OFF TIME is shown
x
Wake up timer is turned off.
< If the wake up timer reaches the off time while the
snooze function is activated, the snooze function will
be automatically cancelled and the SR-2DAB will remain
in standby mode.
Note for use with an iPod Touch/iPhone
When the timer is turned off, the wake up timer indicator
( or ) disappears from the display.
Press the ALARM 1 or ALARM 2 button again to turn it
on.
(When using the SR-2DAB wake up timer with an
iPod Touch/iPhone as the source)
< If you turn the power of an iPod Touch/iPhone off
("Slide to power off"), you cannot use it with the
wake up timer even if it is docked in this system. To
use the wake up timer with an iPod Touch/iPhone as
the source, do not select "Slide to power off" on the
iPod Touch/iPhone. (The screen of the iPod Touch/
iPhone can be turned off without any problem.)
< If Video is displayed on an iPod Touch/iPhone’s
screen, you cannot use it with the wake up timer
even if it is docked in this system. To use the wake up
timer with your iPod Touch/iPhone as a source, select
any item other than Video on the iPod Touch/iPhone.
29
Troubleshooting
If you have problems with your system, read this page and
try to solve the problem yourself before calling your dealer
or a TEAC service Center.
General
No power.
eCheck the connection to the AC power supply. Check
whether or not the AC source is a switched socket. If it
is, confirm that the switch is turned on. Confirm that
there is power to the AC socket by plugging another
item such as a lamp or fan into it.
No sound from speakers.
eSelect the source by pressing the FUNCTION button.
eAdjust the volume.
eRemove the headphone plug from the PHONES jack.
eIf “MUTING” appears on the display, press the MUTING
button.
The sound is noisy.
eThe unit is too close to a TV or similar device. Relocate
it away from the interferring device or turn it off.
Remote control unit does not work.
ePress the STANDBY/ON button to turn the unit on.
eIf the battery is exhausted, replace it with a new one
(see page 5).
eUse the remote control unit within the operation
range (5 m) and point it at the remote sensor on the
front panel.
eRemove obstacles between the remote control unit
and the main unit.
eIf a bright light is near the unit, turn it off.
iPod/iPhone Player
Cannot insert the iPod/iPhone.
eCheck the Dock Adapter (see page 11).
eRemove dust or obstacles from the dock connectors
of the SR-2DAB and the iPod/iPhone, and insert the
iPod/iPhone again.
iPod will not play.
eRemove the iPod/iPhone from the Dock, wait a few
seconds, and insert it again.
eA software update might solve the problem. Visit the
Apple website and download the latest iPod/iPhone
software (see page 11).
Cannot operate the iPod/iPhone.
eRelease the iPod/iPhone HOLD switch.
30
DAB tuner
No sound.
eEnsure that the unit has been able to locate a DAB
station.
“NO STATIONS AVAILABLE” appears on the display.
eConfirm that a DAB broadcast is available in your area.
Cannot access secondary services.
eNot all services are accompanied by secondary
services. If a secondary service is available, the
secondary indicator (“>>”) is displayed next to the
station name.
Display disappears or “service off air” displayed.
eThis may occur if a broadcaster changes the label of a
service or removes the label while you are listening to
it. The unit will try to retune the station. If the problem
persists, follow the procedure for automatic scanning
on page 17.
Cannot listen to the selected station.
eConfirm that you have pressed the SELECT button
to listen to a selection. The station you are currently
listening to will be displayed on the first line of the
display, the second line will show other station options
as you scroll through the station order list. Press the
SELECT button to activate your selection.
A burbling sound is heard on some stations.
eA DAB system is able to produce quality audio from a
low level signal, but when the signal level is too low,
a “burbling” sound might be heard. To reduce this,
try repositioning your antenna to maximize signal
reception.
FM Tuner
Cannot listen to any station, or the signal is too weak.
eTune in a station properly.
eRotate the DAB/FM antenna until you receive a station
clearly.
If normal operation cannot be restored, unplug the
power cord from the socket and plug it in again.
Specifications
TUNER
FM Frequency Range. . . . . . . . . . . . . . . 87.5 MHz to 108 MHz
DAB Frequency Range. . . . . . . . . . . . . . . . . Band III: 5A to 13F
(174.928 MHz to 239.200 MHz)
SPEAKER SYSTEM
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 mm x 2
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ohms
GENERAL
Total Output Power . . . . . . . . . . . . . . . . . . . . . . . . . . 4 W + 4 W
Power Requirement. . . . . . . . . . . . . . . . . . . . . AC 230 V, 50 Hz
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 W
Dimension (W x H x D). . . . . . . . . . . . . 322 x 112.5 x 188 mm
Weight (Net) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 kg
STANDARD ACCESSORIES
Remote control unit (RC-1234) x 1
Battery for remote control unit (CR2032) x 1
Alkaline battery for memory backup (AAA) x 2
Dock Adapter x 4
Stereo mini-plug cable x 1
Mini-plug/pin-plug video cable x 1
Owner’s manual (this document) x 1
Warranty card x 1
< Design and specifications are subject to change without
notice.
< Weight and dimensions are approximate.
< Illustrations may differ slightly from production models.
31
Z
TEAC CORPORATION
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan Phone: (042) 356-9156
TEAC AMERICA, INC.
7733 Telegraph Road, Montebello, California 90640 U.S.A. Phone: (323) 726-0303
TEAC CANADA LTD.
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada Phone: (905) 890-8008
TEAC MEXICO, S.A. DE C.V.
Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacàn, CP 04100, México DF, México Phone: (5255)5010-6000
TEAC UK LTD.
Suites 19 & 20, Building 6, Croxley Green Business Park, Hatters Lane, Watford, Hertfordshire, WD18 8TE, U.K. Phone: (0845) 130-2511
TEAC EUROPE GMBH
Bahnstraße 12, D-65205 Wiesbaden-Erbenheim, Deutschland Phone: 0611-71580
This appliance has a serial number located on the rear panel. Please record the
model number and serial number and retain them for your records.
Model number
Serial number
0709. MA-1488A
Download PDF