Introduction Install Accessories Operation

1
2
3
4
Manual Version 1.0
FY WG 3 Axis Wearable Gimbal is compatible with GoPro HERO4 / 3+ / 3 and cameras with
similar dimensions. Reserved mounting space for GoPro LCD Touch BacPac
Introduction
Rolling Axis
Tilting Axis
FY WG is a lightweight, yet feature-rich, wearable 3 axis gimbal capable of capturing immersive and fully stabilized footages. It is
compatible with GoPro HERO4/ 3+/ 3 (with optional mounting space for GoPro LCD BacPac) and other cameras with similar dimensions.
The FY WG is a miniaturized version of the best-selling FeiYu gimbal, offering exceptional stabilization technology in a wearable form factor
for action cameras. A GoPro T-Clamp adapter is packaged with every FY WG. Users can attach the gimbal to any accessories supporting
the GoPro three-prong mount. The FY WG also contains two 1/4"-20 tripod mounts on its gimbal body, allowing the gimbal to be mounted
in different orientations to all universal tripod screw mount accessories (including helmets, bikes, selfie sticks and other accessories).
Install
STEP 1
Remove the screws on the
battery compartment,
insert two16340 batteries
and tighten the screws.
Accessories For
1/4 Inch Screws
3
Hexagonal Socket
Head Cap Screw
WARNING !!
! WARNING
Do not power on the
gimbal before completing
all the installation steps.
3M
Adhesive
1
Function Button
( ON / OFF )
2
Function
Interface
Panning Axis
T-Clamp
STEP 2
STEP 3
Mount the camera carefully
to the mounting bracket
and tighten the screws.
Vertical
Use the 3M Adhesive to fix the bottom of the Gimbal.
Use with GoPro Accessories, mount the provided T-clamp to the side or
the bottom of the gimbal. Attach T-clamp to any accessories
supporting the standard GoPro three-prong mount.
3 The gimbal can also be mounted directly to other accessories using the
standard 1/4" tripod mount. Tighten all screws and ensure it is firmly
mounted before using the gimbal.
Video And Camera
Charging Interface
Ensure the camera is mounted securely. Press and hold the function button
for 2 seconds. The LED light will turn blue.
Press the function button and hold for 3 seconds, it will be powered off.
POWERING
ON / OFF
Camera In Left
Please choose one way:
1
2
Forward
Camera In Left
Inverted
Camera in Right
Camera in Right
Camera in Right
Screws For
The Battery
Compartment
Camera In Left
Operation
Function
Button
Operating Modes and Functions
Rolling
Function Panning
Button
Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
Mode #2 - Panning and Tilting Mode
Mode #3 - Lock Mode
1/4 Inch Screw Hole
Tilting
Switch between different operating modes by pressing the function button.
The LED light will flash distinctively to indicate different operating modes.
Mode #1 - Panning Mode
T-Clamp Screw Hole
Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
Inversion Mode Pressing the function button three consecutive times in any operating mode, the gimbal will switch to the
Inverted Mode (Allowing the user to flip the gimbal orientation upside down). Pressing the function button three more times
while in Inverted Mode to switch back to the original orientation.
Manual Pulling Locking After the gimbal has been powered on for eight seconds, the tilt angle can be adjusted manually in the Panning Mode
and the Lock Mode. Adjust the title angle to the desired position and wait for 0.5 second until the gimbal registers the new angle.
Reset
Pressing the function button four consecutive times will reset the gimbal to initial orientation.
Tilt and Level Calibration
By using the optional G4 Remote Control, tilt and level can be adjusted without the need to connect to a computer.
For more information, please refer to G4 Remote Control section in the instruction manual.
Function Button Quick Reference
Operation
LED Status
Function Explanation
Operation
LED Status
Sound
Function
Single Tap
LED Flashes Once
Panning Mode
Long Press
For 1 Second
On Constantly
Double Tap
LED Flashes Twice
Panning and Tilting Mode
Power On
LED Flashes Once
Inversion Mode
Turn On And Switch To
The Mode’s LED Status
Two Beeps
Triple Tap
Long Press
For 2 Second
Quadruple Tap
LED Flashes Once
Reset
Long Press
For 3 Second
Turn Off After
A moment
Three Beeps
Shutdown
Lock Mode
T-Clamp
Screw Hole
T-Clamp
Screw Hole
1/4 Inch
Screw Hole
* When the gimbal is in the Inverted Mode, pressing the function button three consecutive times will revert back to the original orientation.
When the battery is low, the gimbal will make three beeping sound and automatically shut down itself.
Accessories
Hexagonal
Socket Head
Cap Screw
Charging : not included
in the pack
M 1.5 Allen Key
T-Clamp
Long screw
Extension Knurled
Thumb Screw
M2*6mm
Charger
Input: DC 5V Min 800mA
Output: DC 4.2V
Rechargeable
Battery
Type: 16340
Video Output
And Camera
Charging Cable
USB Connector
USB Cable
Curved Adhesive
Mounts
Quick-Release
Buckle
3M Adhesive
Power Adapter
European Standard
Connector
5
Remote Control (Optional Item)
Angle Adjustment
Direction Button
UP
DOWN
USB Data Cable For RC
Function
Button
LEFT
RIGHT
Micro
Interface
Direction
Button
Remote
Control
NOTE
The function
button on the
Gimbal will be
disabled after
connect the
Remote Control
Remote Control Operation Instructions
Operation
Explanation
Operation Again
Single Tap
Mode #1 Panning Mode
Other Operation Is Arbitrary
Double Tap
Mode #2 Panning and Tilting Mode
Other operation Is Arbitrary
Triple Tap
Inversion Mode
Triple Tap Again
Quadruple Tap
Reset
Other Operation Is Arbitrary
Tap Button Six Times
Calibration Using Remote Control
Single Tap Again
Mode #3 Lock Mode
Other Operation Is Arbitrary
Long Press
For 1 Second
Long Press
For 3 Second
6
Explanation
Exit inversion mode into original status
Exit calibration and enter standby. Wake the gimbal
by pressing the function button once again
Be sure to insert the
batteries before upgrading
!
In Lock Mode, tilt angle can be
controlled by pressing the“UP”or
“DOWN”button ,pan angle can be
controlled by pressing the“LEFT”or
“RIGHT”button on the remote control.
Tilt and Level Calibration
Using the Remote Control, tilt and level
can be adjusted without the need to
connect to a computer. Calibration
can be done in any operating mode.
Quickly tab the function button six times
to enter the calibration mode. Tilt angle
can be controlled by pressing the
“UP” or “DOWN” button. Roll angle
can be controlled by pressing the
“LEFT” or “RIGHT” button. When
calibration is completed, the gimbal
automatically saves the current setting
and enters the standby mode. Press the
function button once on the Remote
Control to wake the gimbal and
resume operation.
Note: Please make sure gimbal
completed initialization successfully
before attempting calibration.
Turn Off The Gimbal
Firmware Upgrade
In Panning Mode, tilt angle can be
controlled by pressing the“UP”or
“DOWN”button on the remote control
!
Parameters
WARNING
Make sure that the
connection to the
computer is done by the
53.4 mm
Upgrade........
USB Cable
USB Connector
Firmware Upgrade Instruction
91 mm
Micro
Interface
PC
Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware.
Unzip the compressed file locally to your computer. Refer to the connection diagram on how to connect the gimbal with the computer. Please
follow the instructions inside the firmware upgrade package carefully, or there will be a risk of rendering the gimbal inoperable.
Attention : Please make sure that the connection to the computer is done by the USB connector.
35 mm
Tilt and Level Calibration
The tilt and level settings can be calibrated through the use of the configuration software. User can adjust the tilt and diagonal rotation in small intervals
to better adapt to his/her filming scene. Before any calibration, please insert the batteries into the gimbal and refer to the connection diagram to
connect the gimbal with the computer.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Panning Speed Adjustment
The panning speed can be adjusted through the use of the configuration software. User can adjust to the desired panning speed to better adapt to
his/her filming scene. There are three settings available: “SLOW”, “NORMAL” and “FAST”. Default setting is “FAST”.
Attention : Please make sure that the connection to the computer is done by the USB connector.
7
95 mm
Video And Camera Charging Interface
Micro
Interface
Analog Monitor Cable
( Equipped By Users )
Analog Monitor
( Equipped By Users )
This interface can be output 5 voltage and receive analog video signal from GoPro
Connect the video output and camera charging cable as the above diagram
can power the GoPro camera and view video signal from the GoPro camera.
8
After connecting the video output and camera charging
cable, the analog monitor can be used as a display.
Note:
The Analog Monitor Cable and Analog Monitor
are not included in the pack.
Initialize The Gimbal
Initialization Instructions
FY WG needs to be initialized whenever the
following situations are observed after power on
Note: When initialization is completed,
the LED light will quickly flash.
AT T E N T I O N
Please assemble the gimbal in accordance to the diagram provided .
Please upgrade the firmware and configuration settings with the
provided USB data cable.
Please charge the battery with the provided battery charger.
Please install the camera securely before powering on the gimbal.
6.0 V ~ 9 V
Vertical Tilting Angle
320°
Rolls Angle
100°
Horizontal Panning Angle
320°
Tilting Increments
2°/S ~ 75°/S
Panning Increments
3°/S ~ 150°/S
Static Attitude
Tracking Accuracy
0.01 ~ 0.05
(Working Voltage)
Motion Attitude
Tracking Accuracy
Overload Current
Protection
0.1 ~ 0.5
(Motor Overload<2G)
800 mA
Weight
188 g (Without
Batteries & Camera)
Usage Time
3 ~ 4 Hours
Camera Maximum Height
1. Ensure gimbal is fully assembled and camera
is installed properly.
1. The tilt angle is not leveled with the horizontal 2. Place the gimbal on a flat surface and keep it
stationary.
surface.
2. The roll angle is not parallel to the horizontal 3. Power on the Gimbal.
4. Wait for the gimbal to finish its initialization
surface.
before resuming the use of the gimbal.
3. When the gimbal is Full-Axis-Lock mode,
the camera does not stay stationary..
Working Voltage
Camera Maximum Thickness
Camera Maximum Weight
43.6 mm
( Replaceable
mounting bracket )
31.7 mm
( Replaceable
mounting bracket )
150 g
Motionless Flat Surface
DISCLAIMER
FY WG 3-Axis Wearable Gimbal is a feature-rich camera stabilizer, yet lightweight and portable.
It is prohibited for any user to use the gimbal for any illegal purposes.
Guilin Feiyu Electronic Technology Co.,Ltd and our associates assume no liability for any accident, injury, death, loss, or other
claim related to or resulting from the use of this product. In no event shall Guilin Feiyu Electronic Technology Co.,Ltd and our
associates be liable for incidental or consequential damages relating to or resulting from the use of this product or any of its
parts. Damage resulting from use, accident, or normal wear and tear is not covered by our warranty.
Guilin Feiyu Electronic Technology Co.,Ltd reserves the right to amend this manual and the terms and conditions of this
product at any time.
Download PDF