DVI-OPT-TX220-PRO Quickstart Guide

DVI-OPT-xx110 set
Quick Start Guide ver. 0.9
Installation
1.
Connect a multimode SC fiber cable to the SC MM OUT connector
on the TX110 unit.
2.
Connect the transmitter to a DVI source (e.g. computer).
3.
Connect the other end of the SC fiber to the SC MM IN connector
on the RX110 unit.
4.
Plug in the power adaptor to an electrical outlet, and then connect the DC
cable to the receiver unit.
5.
Connect the receiver unit to a DVI display (e.g. monitor).
6.
Power on the DVI source (computer). It reads the EDID from the transmitter,
and outputs the video signal according to the set resolution.
7.
Check the LEDs on the transmitter
a. If both power LED and EDID status LEDs are green, the transmitter
is ready to use.
b. If the power LED does not light up, the DVI source does not send
enough power through the DVI connector, so the external power
adaptor has to be connected to the transmitter.
c. If the EDID state LED lights red, an EDID has to be learned.
8.
Power on the display device (monitor). It will display the picture from the DVI
source (computer).
Using the LEARN button (TX110)
When the button is pressed the EDID state LED turns off to indicate press.
If the button is released sooner than 2 seconds, the press is ignored.
If the button is pressed for more than 2 seconds, the EDID learn mode
activates for a period of 10 seconds.
If the button is pressed for more than 10 seconds, and the unit is not
connected to a display device, the factory default EDID is restored.
EDID state LED legend (TX110)
LED light
GREEN continuous
RED continuous
ORANGE continuous
GREEN blinking
RED blinking
ORANGE blinking
www.lightware.eu
Meaning
EDID valid
EDID invalid
EDID learn mode active
EDID learn success
EDID learn failed
Reloading factory EDID
Learning an EDID (TX110)
1.
Plug in the power adaptor to an electrical outlet, and then connect the
transmitter.
2.
The power and the EDID state LEDs light up.
3.
Press and hold down the LEARN button for two seconds. The EDID state
LED goes dark, and then lights up orange to indicate that learn mode is
activated.
4.
Connect the transmitter to a display device.
(The learn mode is active for 10 seconds).
5.
The transmitter reads the EDID from the display device. Do not disconnect
the device while it lights orange (approximately 10 seconds).
6.
Check if the learning succeeded:
a. If the learning process was successful, the EDID state LED blinks
slowly green for 8 seconds. The stored EDID is changed.
b. If the learning process failed, the EDID state LED blinks slowly red
for 8 seconds. The previously stored EDID remains in memory.
7.
The EDID state LED changes continuous green or red depending on the
validity of the stored EDID.
8.
Disconnect the transmitter (if still connected) and the power adaptor. The
stored EDID remains in memory until it is overwritten. The unit is ready to
use for DVI signal extension.
Restoring the factory default EDID (TX110)
1.
Power up the transmitter by
a. using the power adaptor or
b. connecting it to a DVI source.
2.
Press and keep pressed the LEARN button. The EDID state LED goes dark
for two seconds, and then turns continuous orange to indicate that learn
mode is activated. (Do not connect the unit to a display device.)
3.
Keep the button pressed until the LED starts to blink orange (approximately
after 10 seconds). Five blinks indicate the EDID restore process.
4.
After the restore process finished, the LED blinks slowly green for 8
seconds. The stored EDID is changed back to factory default.
5.
The unit is ready to use for DVI signal extension.
DVI Multimode fiber transmitter
DVI-OPT-xx110 set
Quick Start Guide ver. 0.9
1 DVI connector
1 DVI connector
2 Power LED
3 Hotplug LED
2 Power LED
3 EDID LED
3 Laser LED
4 Learn button
5 Power connector
5 Power connector
6 Fiber connector
6 Fiber connector
7 Thumb-screw
7 Thumb-screw
1
DVI connector
Connect to DVI display.
sufficient.
2
Power LED
Lights green if the unit is powered on.
status.
3
Hotplug LED
Indicates that the display device is connected correctly.
mode.
4
Laser LED
Green light indicates that the laser is properly detected
on the optical input.
Power connector
Barrel plug receptacle for external power adaptor.
5
Power connector Barrel plug receptacle for external power adaptor.
6
Fiber connector
SC
output.
6
Fiber connector SC
7
Thumbscrew
Recessed, slotted thumbscrew for easy mounting by
hand or with screwdriver.
7
Thumb-screw
1
DVI connector
Connect to DVI source for transmitter use.
Connect to display device to learn EDID.
2
Power LED
Lights green if the power supply
(DVI or external adaptor supply)
3
EDID LED
Three
color
LED
displays
See legend for indications.
4
Learn button
Press for 2 seconds to activate learn
Press for 10 seconds to restore factory EDID.
5
www.lightware.eu
type
receptacle
for
is
EDID
multimode
fiber
type
receptacle
for
multimode
fiber
input.
Recessed, slotted thumbscrew for easy mounting by
hand or with screwdriver.
DVI Multimode fiber transmitter
Download PDF