MIXER POWER AMPLIFIERS BG-1015 BG-1030 BG-1060 BG-1120

MIXER POWER AMPLIFIERS BG-1015 BG-1030 BG-1060 BG-1120
OPERATING INSTRUCTIONS
MIXER POWER AMPLIFIERS
BG-1015
BG-1030
BG-1060
BG-1120
This figure represents the BG-1120.
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS ..... 2
2. SAFETY PRECAUTIONS ............................ 3
3. GENERAL DESCRIPTION .......................... 5
4. FEATURES .................................................. 5
5. NOMENCLATURE AND FUNCTIONS
Front ............................................................. 6
Rear .............................................................. 7
6. INPUT CONNECTIONS ............................... 8
7. OUTPUT CONNECTIONS ........................... 9
8. PLUG-IN MODULE INPUT PORT
8.1. Module Installation .............................. 10
8.2. Module Selector Switch Settings ......... 10
9. EQUIPMENT SETTINGS
9.1. Mute Function ...................................... 10
9.1.1. Mute operation A ....................... 11
9.1.2. Mute operation B ....................... 11
9.2. TEL Input Impedance Selection .......... 12
9.3. AUX, PROGRAM, MODULE (BGM)
Output Selection .................................. 12
9.4. Phantom Power On/Off Setting
for Microphone Input ........................... 12
9.5. Changing MIC and PROGRAM Input Types
9.5.1. MIC input ................................... 13
9.5.2. Program input ............................ 13
10. INSTALLATION ......................................... 13
11. RACK MOUNTING BRACKET ATTACHMENT ... 14
12. CONTROL SETTINGS ............................... 14
13. DIMENSIONAL DIAGRAM ........................ 15
14. BLOCK DIAGRAM .................................... 15
15. SPECIFICATIONS ..................................... 16
Accessories ................................................ 16
Optional products ....................................... 16
Thank you for purchasing TOA's Mixer Power Amplifier.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
1. IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
INSTRUCTIONS ESSENTIELLES POUR LA SÉCURITÉ
•
•
•
•
•
•
•
•
•
•
•
•
Lire ces instructions.
Conserver ces instructions pour référence ultérieure.
Respecter tous les avertissements.
Suivre toutes les instructions.
Ne pas utiliser cet appareil à proximité d'eau.
Nettoyer uniquement à l'aide d'un chiffon sec.
Ne pas obstruer les orifices de ventilation. Installer conformément aux instructions du fabricant.
Ne pas installer à proximité de sources de chaleur telles que des radiateurs, des registres thermiques, des
chaudières ou d'autres appareils (notamment des amplificateurs) produisant de la chaleur.
Ne pas contourner la fonction de sécurité de la fiche polarisée ou de mise à la terre. Une fiche polarisée est
équipée de deux broches, dont l'une est plus large que l'autre. Une fiche de mise à la terre est équipée de
deux broches et d'une troisième pour la mise à la terre. Cette dernière, la plus large, est prévue à des fins
de sécurité. Si la fiche fournie ne peut être insérée dans la prise électrique souhaitée, consulter un
électricien pour faire remplacer cette dernière.
Protéger le cordon d'alimentation pour éviter qu'il ne soit piétiné ou pincé, notamment au niveau des fiches,
des prises de courant ou de son point de sortie de l'appareil.
Utiliser uniquement les accessoires spécifiés par le fabricant.
Utiliser uniquement avec le chariot, support, trépied, la patte de montage ou la table
spécifiés par le fabricant ou vendus avec l'appareil. En cas d'utilisation d'un chariot,
manipuler la combinaison chariot/appareil pour éviter les blessures dues à un
renversement.
• Débrancher cet appareil pendant les orages ainsi que lorsqu'il reste inutilisé pendant une période prolongée.
• La maintenance de l'appareil doit être confiée à un technicien après-vente qualifié. Une maintenance s'avère
nécessaire si l'appareil est endommagé (au niveau du cordon d'alimentation ou de la fiche), a été mouillé
par un liquide, un objet est tombé à l'intérieur, s'il a été exposé à la pluie ou l'humidité, s'il ne fonctionne pas
normalement ou s'il est tombé.
2
2. SAFETY PRECAUTIONS
• Before installation or use, be sure to carefully read all the instructions in this section for correct and safe
operation.
• Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or
cautions regarding safety.
• After reading, keep this manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of
important operation and maintenance (servicing) instruction in the literature accompanying the
appliance.
Le point d'exclamation à l'intérieur d'un triangle équilatéral avertit l'utilisateur de l'existence
d'instructions d'utilisation et d'entretien (réparation) dans la documentation fournie avec l'appareil.
WARNING
Indicates a potentially hazardous situation which, if mishandled,
could result in death or serious personal injury.
When Installing the Unit
• Do not expose the unit to rain or an environment where it may be splashed by water or other liquids, as
doing so may result in fire or electric shock.
• Use the unit only with the voltage specified on the unit. Using a voltage higher than that which is specified
may result in fire or electric shock.
• Do not cut, kink, otherwise damage nor modify the power supply cord. In addition, avoid using the power
cord in close proximity to heaters, and never place heavy objects -- including the unit itself -- on the power
cord, as doing so may result in fire or electric shock.
• Be sure to replace the unit's terminal cover after connection completion. Because high voltage is applied to
the speaker output terminals, never touch these terminals to avoid electric shock.
• Avoid installing or mounting the unit in unstable locations, such as on a rickety table or a slanted surface.
Doing so may result in the unit falling down and causing personal injury and/or property damage.
• External wiring connected to the terminals marked with
requires installation by an instructed person.
• The apparatus shall be connected to a mains socket outlet with a protective earthing connection.
• The socket-outlet shall be installed near the equipment and the plug shall be easily accessible.
• Use the Rack mounting bracket MB-1000 (optional) when mounting the unit in an equipment rack. Remove
four M4 x 8 screws on both sides of the unit, and mount the bracket there using the M4 x 16 screws
(supplied with the MB-1000) instead.
When the Unit is in Use
• Should the following irregularity be found during use, immediately switch off the power, disconnect the power
supply plug from the AC outlet and contact your nearest TOA dealer. Make no further attempt to operate the
unit in this condition as this may cause fire or electric shock.
· If you detect smoke or a strange smell coming from the unit
· If water or any metallic object gets into the unit
· If the unit falls, or the unit case breaks
· If the power supply cord is damaged (exposure of the core, disconnection, etc.)
· If it is malfunctioning (no tone sounds.)
• To prevent a fire or electric shock, never open nor remove the unit case as there are high voltage
components inside the unit. Refer all servicing to your nearest TOA dealer.
• Do not place cups, bowls, or other containers of liquid or metallic objects on top of the unit. If they
accidentally spill into the unit, this may cause a fire or electric shock.
• Do not insert nor drop metallic objects or flammable materials in the ventilation slots of the unit's cover, as
this may result in fire or electric shock.
3
CAUTION
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
When Installing the Unit
• Never plug in nor remove the power supply plug with wet hands, as doing so may cause electric shock.
• When unplugging the power supply cord, be sure to grasp the power supply plug; never pull on the cord
itself. Operating the unit with a damaged power supply cord may cause a fire or electric shock.
• When moving the unit, be sure to remove its power supply cord from the wall outlet. Moving the unit with the
power cord connected to the outlet may cause damage to the power cord, resulting in fire or electric shock.
When removing the power cord, be sure to hold its plug to pull.
• Do not block the ventilation slots in the unit's cover. Doing so may cause heat to build up inside the unit and
result in fire.
• Avoid installing the unit in humid or dusty locations, in locations exposed to the direct sunlight, near the heaters,
or in locations generating sooty smoke or steam as doing otherwise may result in fire or electric shock.
• To avoid electric shocks, be sure to unplug the unit's power supply cord when connecting speakers.
• Be sure to follow the instructions below when rack-mounting the unit. Failure to do so may cause a fire or
personal injury.
· Install the equipment rack on a stable, hard floor. Fix it with anchor bolts or take other arrangements to
prevent it from falling down.
· When connecting the unit's power cord to an AC outlet, use the AC outlet with current capacity allowable to
the unit.
· No rack-mounting screws are supplied with the unit. Separately prepare the appropriate screws for the
rack.
• Keep the amplifier over 10 cm (3.94") away from
objects that may obstruct air flow to prevent the unit's
Over 10 cm
internal temperature rise.
(3.94”)
When the Unit is in Use
Over 10 cm (3.94”)
Over 10 cm (3.94”)
• Do not place heavy objects on the unit as this may cause it to fall or break which may result in personal
injury and/or property damage. In addition, the object itself may fall off and cause injury and/or damage.
• Make sure that the volume control is set to minimum position before power is switched on. Loud noise
produced at high volume when power is switched on can impair hearing.
• Do not operate the unit for an extended period of time with the sound distorting. This is an indication of a
malfunction, which in turn can cause heat to generate and result in a fire.
• If dust accumulates on the power supply plug or in the wall AC outlet, a fire may result. Clean it periodically.
In addition, insert the plug in the wall outlet securely.
• Switch off the power, and unplug the power supply plug from the AC outlet for safety purposes when
cleaning or leaving the unit unused for 10 days or more. Doing otherwise may cause a fire or electric shock.
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
L'éclair accompagné d'un symbole représentant une pointe de flèche à l'intérieur d'un triangle
équilatéral avertit l'utilisateur de la présence d'une "tension dangereuse" à l'intérieur de l'enceinte
du téléviseur, dont la magnitude peut être suffisante pour constituer un risque de choc électrique
pour les personnes.
ATTENTION
L'appareil ne doit pas être exposé aux éclaboussures ou écoulements et tous objets remplis de liquide, tels
que vases, ne doivent pas être sur l’appareil.
4
3. GENERAL DESCRIPTION
TOA's BG-1015, BG-1030, BG-1060, and BG-1120 Mixer Power Amplifiers can mix up to a total of 5
independent input signals.
Power output is rated at 15 W for the BG-1015, 30 W for the BG-1030, 60 W for the BG-1060, and 120 W for
the BG-1120.
All units are ideal for use in sound systems requiring small power outputs.
4. FEATURES
• 3 balanced inputs, 1 unbalanced input, and 1 module input
• Phantom-powered microphone input
• Telephone paging input
• Compatible with all 900 Series modules (except for mute buss functions)
• Wide frequency response ranging from 50 Hz to 20 kHz
• Low distortion and low noise level
• Excellent output regulation
• Three different speaker outputs: 4 Ω, 25 V, and 70 V
• MOH (Music On-Hold) output: 1 V, 600 Ω
• 1 W output terminal: 8 Ω
• Independent bass and treble controls
• Input and output terminals for connection of signal processors
• Two different mute functions
• Overcurrent and thermal protection circuitries
• Compact and lightweight
• Desktop or 19" rack mountable
5
5. NOMENCLATURE AND FUNCTIONS
[Front]
5
6
7
MIC
TEL
8
9
PROGRAM
3
AUX
4
MODULE
SIGNAL
PEAK
POWER
2
0
10
0
10
0
10
0
10
0
10
ON
OFF
1
INTEGRATED AMPLIFIER BG-1120
This figure represents the BG-1120.
1. Power switch [
ON /
OFF]
Power is switched on and off with each depression
of this switch.
Note
The amplifier comes into operation about 3
seconds after the power has been switched on.
2. Power indicator [POWER]
Lights green when the Power switch (1) is switched
on.
3. Signal level indicator [SIGNAL]
Lights green when the speaker output level
exceeds 20 dB.
4. Peak indicator [PEAK]
Lights red if output signals approach clipping level.
If steady lit, turn down the corresponding Input
volume control until the indicator flashes only
intermittently.
5. Microphone input volume control [MIC]
Adjusts gain of microphone input.
Turn the knob clockwise to increase the level and
counterclockwise to decrease it.
6. Telephone paging input volume control [TEL]
Adjusts gain of telephone paging input.
Turn the knob clockwise to increase the level and
counterclockwise to decrease it.
7. Program input volume control [PROGRAM]
Adjusts gain of program input.
Turn the knob clockwise to increase the level and
counterclockwise to decrease it.
8. AUX input volume control [AUX]
Adjusts gain of AUX input.
Turn the knob clockwise to increase the level and
counterclockwise to decrease it.
9. Module input volume control [MODULE]
Adjusts gain of Module input.
Turn the knob clockwise to increase the level and
counterclockwise to decrease it.
Protection function to be noted on operation
When the temperature of unit's internal heat sink exceeds the specified limit, the protection circuit
disconnects the output from the inner circuit. Output is automatically restored when the heat sink cools
down below the temperature limit.
6
[Rear]
13
14
15 17
19 22 23
24
Blank panel
18
120V
60Hz
MAX 500W
12
UNIT
BREAKER
4A
G
COM HOT
SENSE
OUTLET
BREAKER
4A
PUSH
RESET
PROGRAM
TEL
G
PUSH
RESET
A
G
COM HOT
–
OUTPUT 120 W
120V
BASS
0
NC
UNSWITCHED
11
10
MIC
COM HOT
OUTPUT 1 W
MOH
TREBLE
0
+
4Ω
25V
70V
8Ω
COM 600Ω COM
PAGE
B
–
BGM
AUX
27
+
MUTE
60Hz
COM
MODULE
MUTE
0
G
OUTPUT 1 W
0
10 0
PREAMP
OUT
MOH
POWER
IN
10
CLASS 2 WIRING
10
28
16
20 21
25 26
This figure represents the BG-1120.
10. AC power cord
Connect this cord to an AC wall outlet of 120 V
AC.
11. Ground terminal
Hum noise may be generated when external
equipment is connected to the unit. Connecting
this terminal to the functional ground terminal of
the external equipment may reduce the hum
noise.
12. AC outlet [UNSWITCHED]
Provides AC power to auxiliary equipment with
power consumption of less than 500 W.
13. Breaker [UNIT]
Cuts off the AC power to the unit when its input
current exceeds the allowable value.
Note
The yellow button in the breaker pops out to
indicate that the breaker has tripped. After
turning off the power and eliminating the cause
of the breaker trip, press the button to reset the
breaker.
14. Breaker [OUTLET]
Cuts off the AC power supply from the AC outlet
if current output exceeds 4 A.
Note
The yellow button in the breaker pops out to
indicate that the breaker has tripped. After
turning off the power and eliminating the cause
of the breaker trip, press the button to reset the
breaker.
15. Input terminal block [PROGRAM, TEL, MIC]
Connect microphone, telephone, and program
source to this terminal block. (Refer to p. 8,
"Input Connections.")
16. Output terminal block [OUTPUT, MOH, MUTE]
Provides outputs for speaker (120 W output and
1 W output), MOH (Music On-Hold), and Mute
control. (Refer to p. 9, "Output Connections" and
p. 10, "Mute Function.")
17. Sensitivity control [SENSE]
Adjusts the sensitivity of the mute circuit.
Turn clockwise to increase sensitivity, and
counterclockwise to decrease it.
18. Bass control [BASS]
Adjusts the bass frequency band level of speaker
outputs for MODULE (BGM), PROGRAM, and
AUX input signals.
Turn clockwise to increase bass output, and
counterclockwise to decrease it.
Bass level is flat at the center position.
19. Treble control [TREBLE]
Adjusts the treble frequency band level of speaker
outputs for MODULE (BGM), PROGRAM, and
AUX input signals.
Turn clockwise to increase treble output, and
counterclockwise to decrease it.
Treble level is flat at the center position.
20. 1 W output volume control [OUTPUT 1 W]
Adjusts the 1 W OUTPUT level.
Turn clockwise to increase the level and
counterclockwise to decrease it.
21. MOH output volume control [MOH]
Adjusts the MOH (Music On-Hold) output signal
level.
Turn clockwise to increase the level and
counterclockwise to decrease it.
7
22. Mute selector switch [MUTE]
Changes the type of mute operation.
(Refer to p. 10, "Mute Function.")
23. Module selector switch [MODULE]
Selects the output terminal for the module signal.
Shift the switch to the PAGE position when using
the paging module, and to the BGM position
when using the BGM module.
24. AUX input terminals [AUX]
An internal mixing type of jack.
–10 dB, 47 kΩ, unbalanced, RCA jack.
Used to connect external equipment input
signals. (Refer to p. 8, "Input Connections.")
26. Power amplifier input terminal [POWER IN]
0 dB, 10 kΩ, unbalanced, RCA jack.
Used to connect input signals from external
signal processing equipment such as limiters and
equalizers.
27. Module input port
Accepts one of 900 series plug-in modules.
For the selection of the most appropriate module,
refer to Plug-in Module Instruction manual.
28. Terminal cover
Make sure that the terminal cover is reattached
after speaker output terminal connection
completion.
25. Preamplifier output terminal [PREAMP OUT]
0 dB, 600 Ω, unbalanced, RCA jack.
Used to feed output signals to external signal
processing equipment such as limiters and
equalizers.
6. INPUT CONNECTIONS
[MIC input connections]
G
COM HOT
MIC
H
C
E
[TEL and PROGRAM input connections]
G
COM HOT
H
C
E
Input source
[AUX input connections]
AUX
H
Input source
E
H
Input source
E
8
7. OUTPUT CONNECTIONS
[Output terminals]
Each amplifier has 3 speaker outputs: 4 Ω, 25 V and 70 V. Use only one of these outputs for connection.
Class 2 wiring may be used.
Note: Impedances indicated in the diagram mean total speaker load impedance.
COM 4Ω
25V 70V
COM 4Ω
25V 70V
4Ω
WARNING
COM 4Ω
25V 70V
5.2 Ω (BG-1120)
10.4 Ω (BG-1060)
21 Ω (BG-1030)
42 Ω (BG-1015)
40.8 Ω (BG-1120)
81.7 Ω (BG-1060)
163 Ω (BG-1030)
330 Ω (BG-1015)
25 V line
70 V line
The terminals marked with the symbol are hazardous live.
The external wiring to these terminals requires installation by an
instructed person.
[Connection of speaker cable]
Step 1. Unscrew the terminal cover.
Step 2. Strip 10 mm (0.39") of insulative jacket from the end of the speaker cable,
as shown in the figure at right.
Step 3. Connect speaker cables to the speaker output terminals.
10 mm
(0.39”)
Step 4. Replace the terminal cover.
WARNING
Be sure to replace the terminal cover after connection completion.
Because high voltage is generated at the speaker output terminals,
never touch these terminals to avoid electric shock.
[MOH output connections]
[OUTPUT 1 W output connections]
The MOH output is rated at 1 V / 600 Ω.
The OUTPUT 1 W output is rated at 1 W / 8 Ω.
600Ω COM
8 Ω COM
G
E
C
H
8Ω
9
8. PLUG-IN MODULE INPUT PORT
A single port for TOA plug-in modules is located on the unit's rear panel. Any 900 Series plug-in module can
be inserted into this port.
Note: Consult your nearest TOA dealer for selection of appropriate module types.
Be sure to turn off the power before performing the following operations:
Mixer power amplifier
8.1. Module Installation
Step 1. Remove the blank panel covering the module
slot on the rear panel.
Step 2. Align the module board with the top and
bottom guide rails, and press in.
Step 3. Using the screws supplied with the module,
secure the module to the rear panel.
Guide rail
900 Series plug-in module
Module mounting screw (supplied with the module)
8.2. Module Selector Switch Settings
Shift the rear panel-mounted Module Selector Switch to either the PAGE or BGM position, depending on the
output terminal to which the module signal is to be sent.
PAGE: Signals from the installed module are only sent to the speaker
outputs.
MODULE
PAGE
BGM: The terminal to which the signal from the module is to be output
differs depending on jumper wire settings inside the unit.
(Refer to p. 12, "AUX, PROGRAM, MODULE (BGM) Output
Selection.")
BGM
Module selector switch
Set both the bass and treble controls to the center position when using the equalizer module.
Caution
Make sure that the supplied blank panel is placed over the module input port when the port is not in use.
9. EQUIPMENT SETTINGS
CAUTION
These servicing instructions are for use by qualified personnel only. To avoid electric shock, do not
perform any servicing other than that contained in the operating instructions unless you are qualified to
do so. Refer all servicing to qualified service personnel.
9.1. Mute Function
The unit features 2 different mute functions, A and B.
Mute A or B can be selected with the rear panel-mounted Mute Selector
Switch.
10
MUTE
A
B
Mute selector switch
9.1.1. Mute operation A
The mute function can be activated either by the TEL, MIC, or MODULE (PAGE) input signal, or by shorting
the rear panel-mounted mute terminals.
[Mute signal settings]
Input signals to activate the mute function can be selected by the internal jumper wire settings. The TEL, MIC,
and MODULE (PAGE) input signals are all factory-preset (Jumpers JP207, JP208, and JP209 are set.) as
muting signals.
Cut off the jumper wire corresponding to the input signal to be disabled for muting.
In any case, shorting the rear-mounted Mute terminals can also actuate the mute function.
JP208
JP207
JP209
T203
T202
T201
MOD
MIC
TEL
Preamplifier board
Note: If Module Input is selected, the mute function can only be used when the Module Selector Switch is set
to the PAGE position.
[Muted signal settings]
Use the unit's internal jumper switch JP301 to select the signal to be muted. Select either the input signal from
the TEL, MIC, and MODULE (PAGE) terminals or from the AUX, PROGRAM, and MODULE (BGM) terminals
as the signal to be muted.
Jumper switch JP301
PAGE: TEL, MIC, MODULE (PAGE)
BGM: AUX, PROGRAM, MODULE (BGM)
Preamplifier output board
Note: Selection is factory-preset to the input from AUX,
PROGRAM, and MODULE (BGM) terminals.
9.1.2. Mute operation B
The mute function can be controlled by way of the rear panel-mounted Mute terminal.
Note: The mute function cannot be controlled by means of an input signal.
[Mute terminal]
: Channel is ON.
: Signal is muted.
Open
MIC
TEL
MODULE (PAGE)
Close
MIC
TEL
MODULE (PAGE)
AUX
PROGRAM
MODULE (BGM)
AUX
PROGRAM
MODULE (BGM)
11
9.2. TEL Input Impedance Selection
The impedance is factory-preset to 10 kΩ. To switch to 600 Ω, change the position of the unit's internal jumper
switch JP204.
600 Ω
T203
T202
10 kΩ
T201
Jumper switch JP204
Preamplifier board
9.3. AUX, PROGRAM, MODULE (BGM) Output Selection
Operations shown in the following tables can be enabled with the unit's internal jumper settings.
[OUTPUT 15 W / 30 W / 60 W / 120 W]
JP210
JP211
JP212
Jumpered
Cut
Jumpered
Cut
Jumpered
Cut
[OUTPUT 1 W, MOH]
AUX:
AUX:
PROGRAM:
PROGRAM:
MODULE (BGM):
MODULE (BGM):
ON
OFF
ON
OFF
ON
OFF
JP213
JP214
JP215
Jumpered
Cut
Jumpered
Cut
Jumpered
Cut
AUX:
AUX:
PROGRAM:
PROGRAM:
MODULE (BGM):
MODULE (BGM):
[OUTPUT 1 W, MOH]
[OUTPUT 15 W / 30 W / 60 W / 120 W]
JP213: AUX
JP214: PROGRAM
JP215: MODULE (BGM)
JP212: MODULE (BGM)
JP211: PROGRAM
JP210: AUX
T203
Preamplifier board
T202
9.4. Phantom Power On/Off Setting for Microphone Input
The phantom power is set to ON or OFF with the unit's internal jumper switch JP201.
It is factory-preset to OFF.
OFF
T203
T202
ON
T201
Jumper switch JP201
Preamplifier board
12
ON
OFF
ON
OFF
ON
OFF
T201
9.5. Changing MIC and PROGRAM Input Types
Both MIC and PROGRAM inputs can be changed from electronically balanced to transformer balanced types
with the following procedures.
9.5.1. MIC input
• Install an optional IT-450 Line Transformer on the preamplifier board as shown below.
• Cut off both JP202 and JP203 jumper wires.
JP202
JP203
T203
T202
Line Transformer
IT-450
Preamplifier board
9.5.2. Program input
• Install an optional IT-453A Line Transformer on the preamplifier board as shown below.
• Cut off both JP205 and JP206 jumper wires.
T202
JP206
JP205
T201
Line Transformer
IT-453A
Preamplifier board
10. INSTALLATION
Keep the amplifier over 10 cm (3.94") away from objects that may obstruct air flow to prevent the unit's
internal temperature rise.
Over 10 cm (3.94”)
Over 10 cm (3.94”)
Over 10 cm (3.94”)
13
11. RACK MOUNTING BRACKET ATTACHMENT
To mount the amplifier in a standard 19" equipment rack, use the optional MB-1000 Rack Mounting Bracket.
Attach the MB-1000 to the amplifier using the 4 supplied screws. When using other screws, ensure that each
screw is shorter than 16 mm (0.63").
Step 1. Remove four M4 x 8 screws on both sides of the unit. The removed screws are not used.
Step 2. Attach the MB-1000 to the unit using four M4 x 16 Machine screws supplied with the MB-1000.
Machine screw M4 x 16
(supplied with the MB-1000)
MB-1000 (optional)
Screws removed in Step 1 are not used.
Notes
• Remove 4 plastic feet on the bottom surface when mounting the unit in a rack.
• Rack mounting screws are not supplied with the unit. Use the screws that are appropriate for the rack.
• When mounting the unit in an equipment rack, the inside
of the rack must be sufficiently ventilated.
Amplifier
To achieve sufficient ventilation, also mount the optional
PF-511 Perforated Panel (1U*):
Amplifier
(1) at the top and the bottom of the rack, and
Perforated Panel
(2) above and below the unit.
Amplifier
PF-511
(1-unit size)
* 1U size = 44.5 mm or 1.75" (reference size)
12. CONTROL SETTINGS
Output levels are adjustable with individual volume controls.
For music play or announcement, adjust the corresponding
volume control so that the peak indicator lights intermittently.
Note that the sound quality is downgraded when the peak
indicator remains lit.
To prevent the accidental change of the settings of input volume
controls, remove their knobs after setting them to the desired
position and attach the volume control covers instead.
Volume control cover
(accessory)
Volume control knob
14
13. DIMENSIONAL DIAGRAM
(Applicable to all models)
1800
(70.87)
Unit: mm (inches)
280 (11.02)
107.4 (4.23)
266.5 (10.49)
88.4 (3.48)
264 (10.39)
This figure represents the BG-1015.
14. BLOCK DIAGRAM
Phantom Power (DC 24 V)
JP201
OFF
ON
Option
EBA
Mic Vol.
Mic
–60 dB/600 Ω
Balanced
Mute
JP207
I.T.
Tel Vol.
Mute
Tel
–20 dB/10 kΩ
JP301
JP208
JP204
I.T.
A
JP209
PAGE
BGM
Mute Cont.
10 kΩ 600 Ω
B
Mute
Mute Cont.
Mute selector
Module
Module
PAGE
Tone
PAGE
OUT
IN
BGM
JP212
Preamp OUT
(Preamplifier Output)
Mute
Power IN
(Power Amplifier Input)
Bass Treble
BGM
Peak
JP215
Power
Option
EBA
Signal
O.T.
Program Vol.
JP211
Program
–10 dB/10 kΩ
Output 1W Vol.
JP214
70
25 Output 15 W/30 W/
4Ω 60 W/120 W
COM.
Power
Output 1 W 1 W/8 Ω
I.T.
AUX Vol.
AUX
–10 dB/47 kΩ
O.T.
MOH Vol.
MOH output
1 V/600 Ω
JP210
JP213
Power
P.T
Power S.W.
Breaker
AC 120 V
60 Hz
Breaker
A.C. Outlet
15
15. SPECIFICATIONS
Model No.
Power Source
Rated Output
Power Consumption
Rated output
Based on cUL standards
Frequency Response
Total Harmonic Distortion
Input
Output
Output Regulation
S/N Ratio
Tone Controls
Cooling Fan Speed
Indicator
Protection
Other Feature
Finish
Dimensions
Weight
(without input module)
BG-1015
15 W
BG-1030
BG-1060
120 V AC, 60 Hz
30 W
60 W
BG-1120
120 W
50 W
40 W
80 W
160 W
260 W
60 W
100 W
150 W
50 Hz – 20 kHz
0.05% at 1 kHz, rated output
Mic:
–60 dB*1, 600 Ω, electrically balanced, M3 screw terminal*2
Tel:
–20 dB*1, 10 kΩ/600 Ω, balanced, M3 screw terminal*2
Program: –10 dB*1, 10 kΩ, electrically balanced, M3 screw terminal*2
Aux:
–10 dB*1, 47 kΩ, unbalanced, RCA jack (internal mixing)
Module:
–20 dB*1, 10 kΩ, unbalanced, card edge connector
Power IN: 0 dB*1, 10 kΩ, unbalanced, RCA jack
Mute:
M3 screw terminal*2
Main:
4 Ω, 25 V and 70 V, balanced, M3 screw terminal*2
Sub:
1 W/8 Ω, unbalanced, M3 screw terminal*2
MOH:
0 dB*1, 600 Ω, balanced, M3 screw terminal*2
Preamp OUT: 0 dB*1, 600 Ω, unbalanced, RCA jack
Under 2 dB, no load to full load
Mic: 60 dB, Tel: 75 dB, Program: 75 dB, Aux: 75 dB, Module: 75 dB
(Band Pass: 20 Hz – 20 kHz, Tone Controls: Centered)
Bass: ±10 dB at 100 Hz, Treble: ±10 dB at 10 kHz
Controls affect only program input, aux input and module (BGM) input
–
Variable by heat sink temperature
Power LED, Signal LED, Peak LED
Self protection, with 1 AC breaker (outside)
Automatic electronic drive limiter
Output disconnected for approx. 3 seconds after the unit is turned on
Panel: ABS resin, black
Case: Steel plate, black, paint
264 (w) x 107.4 (h) x 280 (d) mm (10.39" x 4.23" x 11.02")
4.5 kg
4.8 kg
5.6 kg
6.4 kg
(9.92 lb)
(10.58 lb)
(12.35 lb)
(14.11 lb)
*1 0 dB = 1 V
*2 Distance between barriers on the above screw terminal: 6 mm (0.24")
Note: The design and specifications are subject to change without notice for improvement.
• Accessories
Volume control cover ....................... 5
• Optional products
Line transformer:
IT-450
Line transformer:
IT-453A
Rack mounting bracket: MB-1000
Perforated panel:
PF-511
URL: http://www.toa.jp/
133-02-00090-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising