Optimum T4200 Family Optimum T4200 Family TERMINAL INSTALLATION GUIDE TERMINAL INSTALLATION GUIDE Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. • F CC Part 68 (pending) • • • • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications to the product(s) identified in this manual unless expressly approved by Hypercom could void the user’s authority to operate these product(s). IC CS-03 (pending) CE (pending) A-tick (pending) UL/CUL Listing (pending) 685 Cathcart Street, Suite 1000 • Montreal, QC, H3B 1M7 Tel: 1 866 557-5553 • Fax: 1 866 438-5612 www.pivotalpayments.ca TIG0608 © 2008 Pivotal Payments, all rights reserved. Hypercom and Optimum and Design are registered trademarks of Hypercom Corporation. The Hypercom logo is a trademark of Hypercom Corporation. All other products or services mentioned in this document are trademarks, service marks, registered trademarks or registered service marks of their respective owners. w w w. p i v o t a l p a y m e n t s . c a Optimum T4200 Family Terminal Installation Guide Equipment Check List Paper Roll The Optimum T4200 Family Terminal Installation Guide provides basic setup information to any device within the Optimum T4200 Family. RJ11 Cable (Telephone Cable) Warning: Regional Specific • Do not use if visibly damaged. • Do not expose to temperatures above 140 °F or 60 °C. Note: Images within this guide may not exactly match your device. • Do not disassemble. • Do not incinerate or crush. • Keep out of reach of children and pets. Optimum T4200 Family Power & Cable Connections Power Cord Receipt Paper Installation 2 1 Wiring Clip A/C Power Adapter 1 3 Labeled Ports 2 Printer Cover 3 POWER Port Drop Paper Roll Turn the terminal over. With your fingers, remove the wiring clip from the back of the terminal (as shown). 4 Labeled ports on the back are defined as: - LINE port = RJ11 (telephone) cable - POWER port = A/C Power Adapter & Power Cord - SERIAL port = RS232 cable - PIN PAD port = PIN pad cable - NET port = Ethernet cable 5 Connect Power Cord to A/C Power Adapter. Insert A/C Power Adapter into POWER port (as shown). Turn connector counterclockwise, toward back of the terminal, to lock in place. Insert other end of the Power Cord into the wall receptacle. 6 With your fingers, open the printer cover (as shown). Paper Receipt Guide Drop paper roll into paper holder (as shown). Pull & tear paper against the paper rePull paper (as shown) & close printer cover. ceipt guide. Operate terminal as normal. Swiping Your Credit Card Inserting Your Smart Card 1 NET Port Pull Receipt Paper 1 Smart Card Reader Wiring Clip LINE Port Credit Card Bi-directional Card Reader Insert RJ11 cable into LINE port (as shown). Insert Ethernet cable into NET port (as shown). With your fingers, re-insert the wiring clip over the cables (as shown). Note: Bend the cable 90° at the base of the connector. Swipe credit card through the card reader with a downward or upward motion (as shown). Smart Card Insert smart card (gold chip side up) into the smart card reader (as shown). Accessories Available Regional Specific Optimum T4210 (P/N# 010332-xxx) Optimum T4220 (P/N# 010332-xxx) Optimum T4230 (P/N# 010332-xxx) Paper Roll (P/N# 710015-003) A/C Power Adapter (P/N# 870065-002) Power Cord (P/N# Based on Region) RJ11 Cable (Telephone Cable) (P/N# 810005-010)
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement