Configuring the Millenium II Controller with the Crouzet Logic

Configuring the Millenium II Controller with the Crouzet Logic
Tel: 262-446-0000
Fax: 262-446-0300
E-mail:
bob@grossautomation.com
Connecting CROUZET Logic Millenium II Controller with
Telephone Modem TD-33
Instructions
TD-33
- Communication parameters: 115.2 Kbits, 7bits,
Even, 1, Stop
- First you need to configure the Millenium II
Controller.
- Connect the controller to the PC using the
programming cable.
- Configure the Millenium Controller according to
the instructions on the following pages.
SW 1
ON
- Connect the TD-33 to the controller using the
the programming cable.
1 2 3 4
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
Cable P/N:
88 950 102
9 pin D-sub female
9 pin D-sub female
9 pins D-sub male/male cable
• Configuring the Millenium II Controller with the
Crouzet Logic Software M2.
Rev1.0 28.11.02 JMA / Page:1
Gross Automation (877) 268-3700 · www.crouzetsales.com · sales@grossautomation.com
Tel: 262-446-0000
Fax: 262-446-0300
E-mail:
bob@grossautomation.com
Configuring the Millenium II Controller with the Crouzet
Logic Software M2.
• Connect the Millenium II to the PC using the programming
cable.
• Start the Crouzet Logic Software.
• Select modem controller configuration.
• Select 3 Com US Robotics modem ( compatible with TD-33) as
shown on the following display.
• Confirm with OK in order to close the two windows.
• The controller is now configured.
• Connect the modem with the controller.
Rev1.0 28.11.02 JMA / Page:2
Gross Automation (877) 268-3700 · www.crouzetsales.com · sales@grossautomation.com
Tel: 262-446-0000
Fax 262-446-0300
E-mail:
bob@grossautomation.com
Configuring the Millenium II Controller with the Crouzet
Logic Software M2.
• Select Controller again and set up in order to define PC modem
settings.
Rev1.0 28.11.02 JMA / Page:3
Gross Automation (877) 268-3700 · www.crouzetsales.com · sales@grossautomation.com
Tel: 262-446-0000
Fax 262-446-0300
E-mail:
bob@grossautomation.com
Configuring the Millenium II Controller with the Crouzet
Logic Software M2.
• Select the PC connected modem.
• Enter the dialing number.
• Click on the setting button to open the window above to the right.
• Click the advanced button.
• Check no flow control and no error
correcting control.
• Confirm with Ok.
• the configuration is now completed
• Select:Controller!connection!connect in order to
establish the connection.
Rev1.0 28.11.02 JMA / Page:4
Gross Automation (877) 268-3700 · www.crouzetsales.com · sales@grossautomation.com
Tel:
262-446-0000
Fax
262-446-0300
E-mail:
bob@grossautomation.com
Configuring the Millenium II Controller with the Crouzet
Logic Software M2.
Software and Hardware versions used materials
• CROUZET Controller SA-12
• Release Version - Firmware: 1.0 – 1.4 / 2.0
• Crouzet configuration Software Version 1.2
• Windows 98 SE
• Westermo telephone modem TD-33 V.34 or V.90
• PCMCIA modem on PC side
Rev1.0 28.11.02 JMA / Page:5
Gross Automation (877) 268-3700 · www.crouzetsales.com · sales@grossautomation.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising