Quickstart: SWAMP(I)-24X8

Quickstart: SWAMP(I)-24X8
SWAMP(I)-24X8
quickstart guide
Sonnex™ Multiroom Audio System
1
2
Introduction
Hardware Hookup (Continued)
Bridge Speaker Outputs (Optional)
Bridge speaker outputs to deliver more power to the speakers (8 Ω speaker only).
The SWAMP-24X8 and SWAMPI-24X8 are audio switcher/amplifiers with 24 inputs and eight output zones.
The SWAMP-24X8 and SWAMPI-24X8 are functionally identical. For simplicity within this guide, the term
“SWAMP-24X8” is used except where noted.
2
1
LEFT
+
2
RIGHT
-
+
-
LEFT
+
-
RIGHT
+
-
Hardware Hookup
Connect the Device
Make connections to the SWAMP-24X8 as shown in the following diagram.
!
!
WARNING: This device is capable of delivering immense amounts of undistorted power to your loudspeakers. Please
use caution and adequate ear protection if listening to content at high volume levels as continued exposure to high
sound pressure can cause permanent hearing impariment or loss.
NOTE: If speaker outputs are to be bridged, they must be configured for bridged operation using the
“Installer Mode” menu or Sonnex Tools. For more information, refer to section ➌ “Configuration” on
page 2.
Connect Balanced/Unbalanced Audio Sources
Four balanced/unbalanced audio inputs are provided, utilizing 5-pin terminal block connectors. For
connection details, refer to the following diagrams.
CAUTION: Keep the device unplugged until all the input, network, and speaker wiring is complete.
L
Balanced
Input
CAUTION: Check the speaker wires for shorts and frayed wiring around the SPEAKER OUTPUTS connectors.
R
+-G+-
L
Unbalanced
Input
R
+-G+-
Shield
ANALOG
SOURCES:
From Analog Audio
Sources
POWER:
From Line Voltage
Source L
+
NET:
To Cresnet Devices
Source R
+
Jumpers
SPEAKER OUTPUTS:
To Speakers or SAT-70V/100V
Sonnex Output Transformer
Speaker Connections
Make speaker connections to the SWAMP-24X8 as shown in the following diagram.
-
NOTE: When connecting a SWAMP-24X8 to a Sonnex Link device, Crestron® recommends using
Crestron DM-CBL-8G or high-quality CATe5 sheilded twisted-pair cable. Shielded connectors such
as the DM-8G-CONN must be used.
NOTE: When the SWAMP-24X8 is connected to a control system by Cresnet®, only one Sonnex Link
device can be connected.
NOTE: If the SAT-70V/100V Sonnex™ Output Transformer is connected to a speaker
terminal, use the SAT-70V/100V profile built into the Sonnex Tools application to
configure a high-pass filter on the zone that is connected to the SAT-70V/100V. For
details, refer to the Sonnex Tools help file.
+
(Continued in following column)
For details, refer to the latest revision of the
SWAMP(I)-24X8 Operations Guide, Doc. 7049.
QUICKSTART DOC. 7050C (2028551)
www.crestron.com
10.12
Specifications subject to change
without notice.
888.273.7876
201.767.3400
SWAMP(I)-24X8
Connect Sonnex Link Devices
To increase the number of output zones, the SWAMP-24X8 can connect to Sonnex Link devices via
shielded CAT5e cable to increase the number of output zones. Up to eight Sonnex Link devices can be
connected to one SWAMP-24X8.
Ground
SPDIF OUT
To Digital Audio
Receiver
+
Source R
Shield
LAN:
10BASE-T/100BASE-TX
Ethernet to LAN
SPDIF SOURCES
From Digital Audio
Sources
1
Source L
Shield
DIGITAL OUT:
To Sonnex Link
devices
+
-
+
SWAMP(I)-24X8
quickstart guide
Sonnex™ Multiroom Audio System
3
4
Configuration
Operation (Continued)
Use the “Installer Mode” menu or the Sonnex Tools software (part of Crestron Toolbox™) to configure a Sonnex
system.
▲
Main Menu
Source Mode
Use the SWAMP-24X8’s “Installer Mode” menu to configure an entire SWAMP 24X8 system using only the front
panel controls.
To enter the “Installer Mode” menu, press and hold the ▼ and ▲ buttons for approximately 5 seconds. The
“Installer Mode” menu is displayed.
Installer Mode
Source Setup
Zone Mode
Zone mode uses the front panel to route a source signal to a selected zone. To use Zone mode:
Press the ▼ or ▲ buttons to scroll through the available choices below, then press ENTER.
•
Source Setup: Select this option to adjust the compensation level for each input source.
•
Zone Setup: Select this option to configure each output zone’s settings for audio, Sonnex links (busses),
bridging (with other outputs) and power output.
•
Expander Status: Select this option to view the status of each connected SWAMPE Sonnex Multiroom
Audio Expander.
1.
From the “Main Menu”, press the ▼ or ▲ buttons to display Zone Mode and press ENTER.
2.
Press the ZONE button of the zone to be controlled.
3.
Press the SOURCE button of the source to be routed. The associated SOURCE and ZONE LEDs light and
the display shows the zone’s selected source. Alternatively, press the ZONE button twice to turn on the
zone and connect the last-selected source.
4.
To turn off the zone, press the ZONE button.
5.
Press MENU to return to the “Main Menu”.
•
Amplifier Status: Select this option to view the settings and operating status of each of the SWAMP-24X8
amplifiers as well as the amplifiers of connected SWAMPE Multiroom Audio Expanders.
•
Network Setup: Select this option to configure and view the Ethernet settings of the SWAMP-24X8.
1.
From the “Main Menu”, press the ▼ or ▲ buttons to display Source Mode and press ENTER.
•
Control Setup: Select this option to configure the SWAMP-24X8 for use with a Crestron control system
and lock/unlock the front panel controls.
2.
Press the SOURCE button of the source to be routed. The associated SOURCE LED lights.
•
About: Select this option to view information about the firmware.
3.
Press the ZONE button(s) of the zone(s) to be selected. The associated ZONE LED(s) lights.
4.
To remove a zone from a source, press the desired ZONE button. The associated ZONE LED turns off.
5.
Press MENU to return to the “Main Menu”.
Operation
The SWAMP-24X8 can be controlled from the front panel or Sonnex Tools software in Crestron Toolbox.
Source Mode
Source mode uses the front panel to select a source signal and route it to multiple zones. To use Source mode:
Volume Control
To raise the volume in the selected zone(s), turn the VOLUME knob clockwise. To lower the volume in the selected
zone(s), turn the VOLUME knob counterclockwise.
NOTE: For more information, refer to the Crestron Toolbox help file.
When operated from the front panel, the SWAMP-24X8 operates in either the Zone mode or Source mode.
The specific patents that cover Crestron products are listed at patents.crestron.com.
Use the “Main Menu” to select Zone mode or Source mode. To display the “Main Menu”, press MENU until Main
Menu appears.
(Continued in following column)
2
For details, refer to the latest revision of the
SWAMP(I)-24X8 Operations Guide, Doc. 7049.
QUICKSTART DOC. 7050C (2028551)
www.crestron.com
10.12
Specifications subject to change
without notice.
Crestron, the Crestron logo, Cresnet, Crestron Toolbox, and Sonnex are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest
in the marks and names of others.
©2012 Crestron Electronics, Inc.
888.273.7876
201.767.3400
SWAMP(I)-24X8
Alternatively, Sonnex Tools software can be used to quickly configure a system using a simple-to-use graphical
interface. For more information, refer to the Sonnex Tools help file.
4
Power
To turn on the SWAMP-24X8, move the POWER switch to . To turn off the SWAMP-24X8, move the POWER switch
to .
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising