LG-088310 BT-3583 Web server

LG-088310 BT-3583 Web server
Web server
BT-3583
Features
Front view
1
Voltage: 100 - 240 Vac
Frequency: 50 - 60Hz
Zigbee technology: Radio frequency band 2.4 GHz (16 channels) Bitrate: 250 KB/s
Self-healing MESH Network with high level of security
(AES128) according to IEEE 802.15.4 (LR-WPAN)
IP Wi-Fi Technology: – IEEE 802.11 b/g/n (2.4 GHz) 13 channels
– Method of encryption and authentication supported:
OPEN networks
WPA-PSK, including TKIP
WPA2-PSK, including AES
WEP 64 bits (5 digit ASCII codes or 10 hexadecimal digits)
WEP 128 bits (13 digit ASCII codes or 26 hexadecimal digits)
WPA authentication (supported for WPA2-PSK)
– Hidden networks supported
Performance: Capacity: 150 m in free field point to point
NOTE: it is recommended to install the Gateway Zigbee close to the Wi-Fi router
NOTE: it is possible install only one gateway Zigbee for each system
3
LG-088310
2
4
Legend
1. Button + LED Wi-Fi;
2. Button + LED network Zigbee;
3. RJ45 connector (for future use);
4. Fixed green LED = ON
Installation
To use the Gateway Zigbee device download the free app "MyHomePlay" available on
and
.
Installation of the plug
MQ01020-a-EN
27/01/2016
1
Web server
BT-3583
LG-088310
Installation of stabilizer for UNEL sockets.
1s
1s
1s
1s
Configuration
LED legend
0.06s
Off
1s
1s
1s
1s
1s
1s
1s
1s
1s
1s
0.2s
1s
1s
1s
1s
1s
1s
1s
Fixed light
1s
1s
1s
1s
Slow blinking
1s
1s
1s
1s
1s
1s
1s
1s
1s
Rapid flashing
0.06s
0.2s
1s
0.06s
Flashing mode
0.2s
0.06s
0.06s
0.2s
0.06s
2s
2s
0.2s
0.06s2s
1s
Steady flashing. Two per second.
1s
1s
1s
1s
0.2s
0.06s
0.2s
3 pulses / 3 s
1s
Steady flashing. One per second.
1s
1s
0.06s
0.2s
2s
1s
1s
0.06s
1s
1s
1s
0.2s
1s1s
2s
0.06s
1s
0.2s
1s
2s
3 Flashes in a second and pause for 2 seconds.
1s
1s
0.2s
1s
0.06s2s
Emitter:
2s
device which controls one or more receivers. An emitter0.2s
can be battery powered or connected to the mains.
2s
1s
2s
2s
1s
2s
1s
MQ01020-a-EN
2
1s
1s
NETW.
Receiver:
device connected to a load.
A receiver must be connected to the mains.
LEARN
27/01/2016
4
NETW.
NETW.
Web server
BT-3583
LG-088310
Creation of Zigbee network
Procedure to insert all devices on the same Zigbee network; the devices belonging to the
same network can send and receive controls from each other.
Creation
N
L
3 mm max.
B
N
L
A
N
L
3 mm max.
B
N
L
B
A
NETW.
LEARN
NETW.
A
3s
B
A
NETW.
LEARN
NETW.
LEARN
Then press the NETW button briefly of a
device to be added to the network: the corresponding orange LED lights up with fixed
light and then flashes slowly.
LEARN
Press and hold for 3 seconds the NETW
button of a device connected to the power
supply: the orange LED lights up with fixed
light when the network is created and then
flashes quickly.
When the LEDs of all devices are flashing, briefly press the
NETW button of the first device. The LEDs of all devices added to the
network will be switched off, except on the first device, where the LED
will continue to flash three times every three seconds.
NETW.
+
LEARN
A2
...+
Bn
NETW.
+
A1
LEARN
LEARN
B1
NETW.
3s
Repeat for all devices (wired or battery powered) to be
Bn
added to
A2
B1the network.
A1
+ fixed light and
. . .then
+ lights up with
+ goes
Note: if the LED
off, the device is out of range.
NETW.
LEARN
NETW.
LEARN
NETW.
LEARN
N
Add a device Lto an existing network
C
A
NETW
N
L
A
C
.
A
N
L
N
LEAR
NETW.
N
L
C
A
NETW.
A
C
.
NETW
A
NETW.
B
LEARN
NETW.
LEARN
C
LEARN
LEARN NETW.
NETW.
LEARN
LEARN
LEARN
NETW.
N
LEAR
B
NETW.
LEARN
C
/
/
/
Briefly press the NETW button of
any device: the orange LED
flashes quickly.
Briefly press the NETW button of the
device to be added: the orange LED
lights up with fixed light and then flashes
slowly.
Press the NETW of the device from which the procedure is started:
all LEDs turn off.
C
C
NETW
.
C
A
LEAR
N
.
NETW
A
LEAR
N
/
MQ01020-a-EN
27/01/2016
C
3
LEARN
/
/
NETW.
C
LEARN
LEARN
NETW.
LEARN
B
Web server
BT-3583
LG-088310
Remove a device from the network
C
C
.
NETW
A
N
LEARN
B
NETW.
LEAR
NETW.
LEARN
C
> 15"
Briefly press the
NETW button
>5"<15"
of the device to be removed: the LED
flashes quickly.
Press and hold the NETW>2"<5"
button for 10 seconds
until the orange LED turns off
and then flashes quickly.
To delete the network, perform the above operation for all devices.
Wi-Fi LED status
Off
Red LED
Wi-Fi connection - weak signal level
Red LED
Without Wi-Fi connection
Orange LED
Wi-Fi connection - medium signal level
Orange LED
Without Wi-Fi configuration (default)
Green LED
Wi-Fi connection - good signal level
Green LED
Wi-Fi connection in progress
>2"<5"
Wi-Fi button management
Red LED
Restores the default configuration
> 15"
>5"<15"
Orange LED
>2"<5"
Wi-Fi connection with mobile device
>5"<15"
>2"<5"
Green LED
WPS procedure
>2"<5"
MQ01020-a-EN
4
27/01/2016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising