model sb200, sb500, sb1100 side mount telescopic

model sb200, sb500, sb1100 side mount telescopic
Document Number
XM-KRE1PMEX-R5C
LIGHTING
PRODUCTS
KRER5C-Rev140115
26 Southern Blvd., Nesconset, NY 11767
TEL 631.724.8888 FAX 631.360.9727
TOLL FREE 1.800.645.0074
www.fireresearch.com
MODEL SB200, SB500, SB1100
SIDE MOUNT TELESCOPIC POLE
INSTALLATION INSTRUCTIONS
Refer to the lamphead specific Safety Summary and Maintenance sheet before installing or performing maintenance.
When positioning a telescopic pole ensure that the lamphead clears all obstructions and the twist lock is accessible.
The side mount brackets are adjustable along the outer pole to allow for mounting location flexibility. The exception to this is when
the optional pole-up indicator switch is installed.
Install Side Mount Models
Refer to drawings on page 2.
1. Place the pole in position to check for fit and freedom of operation. Mark the vertical center line for the pole.
2. Measure and mark mounting screw locations. If the optional mounting plate is used use it as a template.
3. Drill mounting screw, alignment pin, and wire holes as required. (Refer to drawing on page 2.) The brackets use a 3/8-16
screw, the alignment pins require 3/16" diameter holes, the indicator wire hole is 1/4". The optional mounting plate holes are
clearance for 5/16" screws.
Note: If optional indicator switch is installed, take notice of the bracket location on the pole and switch orientation.
4. Remove the brackets from the outer pole and install at mounting location. Ensure the O-ring is seated on the standoff and the
four spring pins align correctly. Secure in place with the provided flat head 3/8-16 screw. (If the optional mounting plate is
used, secure the plate with 5/16-18 SS hardware.)
5. Position the pole on the brackets and secure with the front collars and screws.
6. Ensure that approved strain relief for the wiring is installed.
Wiring
12/24 VDC
Connect the BLACK wire to GROUND.
Connect the RED (or WHITE) wire to POWER.
120/240 VAC
Connect the GREEN wire to chassis GROUND.
Connect the WHITE wire to NEUTRAL (LINE 1 for 240V).
Connect the BLACK wire to POWER (LINE 2 for 240V).
SB200
Side Mount
Pull-Up
Page 1 of 2
SB500
Side Mount
Push-Up
SB1100
Side Mount
Push-Up
Remote
KRER5C-Rev140115
Side Mount
Spring Pin
(4 Places)
Side Mount
Bracket Assembly
Notes:
- The side mount brackets are adjustable along the outer pole
except when the optional pole-up indicator switch is installed.
- When the optional indicator switch is installed ensure that
the 1/4" wire holes are aligned, the bracket is in the correct
position on the pole for the pole magnet to activate the switch,
and the switch is mounted facing up.
O-Ring
Silver Billet
Standoff
Rear
Collar
1/4" Hole
Plug
3/8-16
Mounting
Screw
Front
Collar
SB200
Side Mount
Pull-Up
Screw
(4 Places)
Locking
Collar
SB500, SB1100
Side Mount
Push-Up
C/L
Side Mount Bracket
Mounting Dimensions
9/16"
Side Mount
Bracket
1 1/8"
Optional Indicator
Switch Only
1/4" Wire Hole
9/16"
Indicator Switch in
Top Bracket
Side Mount
Bracket
Prepare for
3/8-16 Screw
3/16" Dia.
Alignment Pin Hole
(2 Places)
Side Mount
Bracket
Locking
Collar
Optional Mounting
Plate Dimensions
Plate mounting holes are
clearance for 5/16" screws.
Indicator Switch in
Bottom Bracket
Side Mount
Bracket
2 1/4"
Wire Strain
Relief
Split
Collar
3 3/4"
Rubber
Handle
With indicator switch
installed on SB200
bracket must be 13" from
bottom of outer pole.
With indicator switch
installed on SB500
bracket must be at the
top of outer pole.
Wire Strain
Relief
3"
4 1/2"
Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising