Oasis-user manual

Oasis-user manual
Contents
For a Better Experience
Oasis User Manual
Bluetooth Transmitter and Receiver 2-in-1
Avantree TC500
Scan me for warranty registration
1. Features & AptX low latency
Features & AptX low latency
2
2.
Package Contents
4
latest “AptX low-latency” technology for CD-like quality sound with virtually no delay.
3.
Product Overview & Control Functions
5
Multifunctional, supporting optical, bypass and voice prompts. Providing the best
4.
LED indications
7
5.
Use as a Transmitter (TX mode)
9
6.
Use as a Receiver (RX mode)
10
7.
Bypass mode (Non-Bluetooth)
11
8.
Pair and Connect two Devices Simultaneously
12
9.
Restore Factory Default Settings
14
10. Product Specifications
15
11. Troubleshooting
16
12. Warnnings
17
www.avantree.com
2. Package Contents:
Avantree Oasis is a wireless long range audio transmitter & receiver incorporating the
1.
Button
OPT
SBC
LL
APTX
B
A
RX
SBC
OPT
LL
AUX
APTX
TX
A
B
F
H
TX/RX
switch
Transmitter mode
Receiver mode
Slide to TX to enter transmitting mode.
Slide to RX to enter receiving mode.
eto
Blu
www.avantree.com
G
TX
ass
Byp
Power / Mode
switch
-4-
Status
In receiving mode
Flashes GREEN and WHITE alternately to indicate Oasis is in pairing mode
In transmitting mode
Flashes GREEN and WHITE alternately to indicate Oasis is in pairing mode
Bypass mode
Optical audio mode
AUX
AUX audio mode
SBC
Oasis is using SBC codec
APTX
Oasis is using aptX codec
LL
Oasis is using aptX low latency codec
A
Oasis is using device A
B
Oasis is using device B
8. Pair and Connect two Devices Simultaneously
In TX mode
1) Pair with the first device by following the previous instructions in the “Use as a
Transmitter (TX mode)” section.
2) Pair with the second device
• Set second headphones/speaker to pairing mode.
• Set Oasis to pairing mode again, press the
button for 3s until the TX LED
flashes GREEN and WHITE.
• Wait until connected. Once Oasis connected to two devices, you will see LEDs
A and B both illuminated.
Notes:
1) For improved compatibility and sound quality, we suggest that you use
Bluetooth devices with CSR chipset, e.g. Avantree Audition Pro, Plantronics
backbeat pro, etc.
2) When using dual-link, Oasis doesn’t support aptX low latency.
TX/RX switch
SBC codec (most standard Bluetooth audio)
~ 220ms
-3-
4. LED indications
6. Use as a Receiver (RX mode)
1) Connect audio source (TV, DVD etc.) to Oasis "TX Input" port with the audio
cables provided (optical or AUX/RCA).
2) Connect Oasis to a power source (TV, PC USB socket or power adapter) with a
USB cable.
3) Slide TX/RX switch to the "TX" position.
4) Slide Power/Mode switch to the "Bluetooth" position.
5) Select the correct audio input mode (AUX/OPT) by short pressing the
button (Very Important)
6) Pairing - Pair Oasis with your Bluetooth-enabled headsets/speakers.
• Set Oasis into pairing mode, TX LED flash GREEN / WHITE alternately fast.
– First-time use: Oasis will auto enter pairing mode (with clear memory).
– Afterward: press
button for 3 seconds.
• Set your headsets/speakers to pairing mode refer to its user manual.
• Wait until connected (For quick pairing, better keep them within 1 meter when
pairing)
1) Connect your speaker to Oasis "RX Output" port with the audio cable provided
(optical or AUX/RCA).
2) Connect Oasis to a power source with USB cable and adapter.
3) Slide TX/RX switch to the "RX" position.
4) Slide Power/Mode switch to the "Bluetooth" position.
5) Select the correct audio input mode (AUX/OPT) by short pressing the
button (Very Important)
6) Pairing - Pair Oasis with your Bluetooth-enabled phone/PC/tablet.
• Set Oasis into pairing mode, RX LED flash GREEN / WHITE alternately fast.
– First-time use: Oasis will auto enter pairing mode (with clear memory).
– Afterward: press
button for 3 seconds to enter.
• Active Bluetooth on your phone or another device to find “Avantree Oasis” to
connect.
• Wait and connected (For quick pairing, better keep them within 1 meter when
pairing).
-9-
In RX mode
1) Pair with the first device by following the previous instructions in the “Use as a
Receiver (RX mode)” section.
2) Pair with the second device
• Set Oasis to pairing mode again, press the
button for 3s until the RX LED
flashes GREEN and WHITE.
• Active Bluetooth on the second device to find “Avantree Oasis” to connect.
• Wait until connected. Once Oasis connected the two devices, you will see LEDs
A and B both illuminated.
9. Restore Factory Default Settings
You may need to reset Oasis if it is not working as expected. When Oasis is reset to
factory default settings, all the paired device information will be cleared.
1) Slide Power/Mode switch to the “Bluetooth position”.
2) Make sure Oasis is not connected to any Bluetooth devices – LEDs A and B should
both be off.
3) Press and hold the
and
buttons together until you hear voice prompt
“pairing history cleared”.
- 13 -
12. Warnnings
1) I am having trouble pairing and connecting to my Bluetooth device.
Please check the following:
1. Your wireless device supports the wireless profiles listed in the specifications.
2. Oasis and your device are next to each other or within 3 feet / 1 meter.
3. Make sure both Oasis and the wireless device are in pairing mode.
Avantree Technology CO.,Ltd.
The 4th Floor, Yurpeng Building, NO.1019 Jiabin Rd, Luohu District, Shenzhen,
Guangdong, China.
This device complies with part 15 of the FCC Rules. Operation is subject to the
condition that this device does not cause harmful interference (1) this device may
not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.Changes or
modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
- 17 -
7. Bypass mode (Non-Bluetooth)
Bypassing means using Oasis as a non-Bluetooth device which connects the TV
and speaker via wires directly. This design enables you to switch between wired
(Bypass mode) and wireless (Bluetooth mode) with just one switch without the need
to disconnect any cables.
1) Connect audio source (TV, DVD etc.) to Oasis “TX Input" port with the audio
cables provided (optical or AUX/ RCA).
2) Connect your speaker to Oasis "RX Output" port with your own audio cable
(optical or AUX/RCA).
3) Connect Oasis to a power source with USB cable and adapter.
4) Slide the Power/Mode switch to the "Bypass" position.
5) Select the correct audio input/output mode (AUX/OPT) by short pressing
the
button.
(Important Note: Bypass for AUX to AUX & OPT to OPT only).
6) Ready for use.
- 10 -
Note: Only one device can play music at any time. You must stop the music on one
device to play on the other.
11. Troubleshooting
-7-
-6-
5. Use as a transmitter (TX mode)
- 12 -
2) After connecting and pairing with my wireless device, I cannot hear any music
from my sound system.
1. Make sure you select the correct audio input mode (AUX/OPT) by short
pressing the
button.
2. Make sure to remove the protective head on optical cable.
3. In Optical mode, Oasis support device with sampling rate under 48kHz.
RX
-5-
-8-
- 16 -
Slide to “
” to turn off the device.
Hold this button for about 3 seconds.
Status indicators
oth
OPT
Power off
Enter paring mode
In AUX audio mode, short press once.
(OPT mode doesn’t support).
Details see next page.
Avantree TC500
TX
Slide to “Bypass” to power on & enter
Bypass mode.
Volume up/
Next song
Indicate status
Wireless Transmitter and Receiver 2-1
Scan me for warranty registration
RX
Bypass mode
In AUX audio mode, short press once
(OPT mode doesn’t support).
AUX
APTX
Oasis User Manual
Indicator
Operation
Slide to "Bluetooth" to power on & enter
Bluetooth mode.
Volume down/
Previous song
OPT
SBC
LL
RX
B
TX
A
For a Better Experience
E
~ 70ms
Short press once.
Short press once to switch between
AUX/ Optical switch
AUX (3.5mm) and Optical audio mode.
Voice prompt on/off Hold for 3 seconds to switch Voice on/off.
th
oo
et
Blu
ss
pa
D
~ 40ms
aptX codec
Reconnect
A
B
By
C
Function
The audio delay will be
aptX Low Latency codec
-2-
Status indicators
AUX
Audio delay when paired with different headphones/receiverHeadphones/receiver support -
Power/
Mode switch
RX
supports the normal AptX codec, or the SBC one, those codecs will be used instead.
directly to any wireless headphones or speakers.
Bluetooth mode
TX
the other side device must support the same codec. If the other side device only
solution to enable your TV or home audio system to wirelessly stream hi-fi audio
-1-
3. Product Overview & Control Functions
A. Avantree Oasis (BTTC-500)
B. Power adapter
C. USB charging cable
D. Optical cable
E. 3.5mm audio cable
F. 3.5mm female to RCA male cable
G. User manual & Quick user guide
To take advantage of the better performance of the APTX Low Latency Codec,
- 11 -
10. Product Specifications
•
•
•
•
•
•
•
•
•
•
BT version: 4.1
Supports profiles: A2DP, AVRCP
Audio codec: AptX, AptX-LL, SBC
Operational range: Class I, up to 50 meters
Input voltage/ current: Micro USB DC5.0V 500mA
Operating temperature:-10°C ~ 45°C
Storage temperature: -20°C ~ 60°C
Support sampling rate in optical mode: ≤48KHz
Product size: 114×75×30mm
Product weight: 90g
- 15 -
- 14 -
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the radiator
your body: Use only the supplied antenna.
Dispose of the packaging and
this product in accordance with
the latest provisions.
- 18 -
For a Better Experience
Need help?
- FAQ:support.avantree.com
- Live chat: www.avantree.com (5:00 pm–1:00 am PST)
- Email: support@avantree.com
- Video user guide for Oasis on Youtube.com
- Telephone support:+1 408 600 0579 (CET 8am-3pm)
+1 800 232 2078 (PST 9am-5pm)
+86 755 82285022 (CST 9am-6pm)
www.avantree.com
support@avantree.com
Z-PKMN-T500-V0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising