SureCall Fusion4Home User Guide
Fusion4Home
™
2G/3G & 4G Home Signal Booster Kit
User Guide
Table of Contents
Thank you for purchasing SureCall’s Fusion4Home cellular signal booster kit. Fusion4Home was
specifically designed to eliminate frustrations over dropped calls, limited range and slow data rates by
amplifying incoming and outgoing cellular signals in homes up to 2,000 square feet.
The Fusion4Home provides enhanced cellular signals for multi-carrier 2G, 3G and 4G voice and data
reception. If you have any questions while assembling this kit please contact tech support at 1-888-3656283 or email us at: support@surecall.com.
Important:
Before installing your booster you need to register it with your carrier. You can do so online at the
following urls:
Verizon: http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html
AT&T: https://securec45.securewebsession.com/attsignalbooster.com/
T-Mobile: https://www.signalboosterregistration.com/
Sprint: https://www.sprint.com/legal/fcc_boosters.html
U.S. Cellular: http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
How It Works
Package Contents
Pg. 3
Pg. 4-5
Installation Overview
Pg. 6
Installing Your Hardware
Finding the Strongest Signal
Installing the Outside Antenna
Installing the Inside Antenna
Installing Signal Booster
Pg. 7
Pg. 8-9
Pg. 10-11
Pg. 12-13
Configure Gain Setting
Troubleshooting
Pg. 14
Pg. 15-16
Specification
Pg. 16
Kitting Information
Pg. 17
Warranty
Pg. 18-19
Safety Information
2
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
Pg. 19
How It Works
SureCall’s Fusion4Home is a high-quality bidirectional signal booster that enhances
cellular signals to areas that are prone to weak cellular coverage.
Fusion4Home works with two antennas:
• An inside antenna that communicates with your cell phone.
• An outside antenna that communicates with the cell tower.
Signals sent from a cell tower are received by the outside antenna, amplified by
the booster and then sent to your phone via the inside antenna. When your phone
transmits, the signal is sent to the inside antenna, and then sent to the cell tower
via the outside antenna.
Outside Antenna
Coaxial Cable
Inside Antenna
Signal Booster
This device may be operated ONLY in a fixed location for in-building use
SureCall SureCall
| 48346 Milmont
| 48346 Drive,
Milmont
Fremont
Drive, Fremont
CA 94538
CA| 1-888-365-6283
94538 | 1-888-365-6283
| sales@surecall.com
| sales@surecall.com
33
Package Contents
1. Unpack all package contents. For missing or damaged items, contact your reseller.
2. Turn over the signal booster and record the model and serial number for reference:
Serial #: Purchase Date: 3. Keep the carton and packing material to store the product in case you need to return it.
Standard Fusion4Home signal booster packages include the following items:
• One SureCall Fusion4Home booster
• One outside antenna
• Cable for connecting the outside antenna to the signal booster
• One inside antenna
• One power supply
Signal Booster
Fusion4Home
Outside Antenna (Option)
Omni Omni
CM288W
Yagi Yagi
CM230W-S
RG6 Outdoor and SC-240 Indoor Cable
Inside Antenna (Option)
PanelPanel
Right Angle
CM222W
Dome CM248W
Warning: U
nauthorized antennas, cables, and/or coupling devices are prohibited by FCC new rules. Please contact the FCC for details:
1-888-CALL- FCC. Changes or modifications not expressly approved by SureCall could void the user’s authority to operate the equipment.
4
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
Package Contents
Note: Fusion4Home is available in three kits that are customized to your particular needs.
Please determine which kit you have from the following list:
Model
Package Options
SC-PolyH-72-ORA-CA-Kit
1 Outdoor Omni Antenna, 1 interior right angle antenna and 50’ RG6 coax cable
SC-PolyH-72-YRA-CA-Kit
1 Outdoor Yagi Antenna, 1 interior right angle antenna an 50’ RG6 coax cable
SC-PolyH-72-YP-CA-Kit
1 Outdoor Yagi Antenna, 1 interior panel antenna, 20’ SC-240 and 50’ RG6 coax cable
For a detailed description, see Kitting Information on page 15.
Antenna Type
Model No.
Usage Coverage
Omni Outdoor Antenna
SC-289W
Omni antennas are ideal
for topographies with minimal
obstacles, they have 360º
reception
Yagi Outdoor Antenna
SC-231W
Yagi antennas are designed to
reach carrier towers that are up
to 30 miles away
Right Angle Antenna
SC-121W
Designed for signal
enhancement in 1-2 rooms
Panel Antenna
SC-248W
Panel Antennas allow optimum
reception to targeted areas
Note: Due to the recent change of our company name from Cellphone-Mate (CM) to SureCall (SC) we have changed the prefix on all of our antennas, cables
and accessories from CM to SC-.
SureCall SureCall
| 48346 Milmont
| 48346 Drive,
Milmont
Fremont
Drive, Fremont
CA 94538
CA| 1-888-365-6283
94538 | 1-888-365-6283
| sales@surecall.com
| sales@surecall.com
55
Before You Install
1.Ensure that you have positioned the booster close enough to an existing electrical
outlet.
2. Ensure that there is sufficient cable length between proposed outside antenna
location and booster connector.
3.Ensure that you have sufficient cable length between proposed inside antenna
location and booster connector. Additional cable may be purchased from your dealer,
if needed.
Installation Overview
Step 1. Find the outside area that has the strongest signal. (See page 7 for directions as needed)
Step 2. Install the outside antenna in the area identified in step 1. (See page 8-9 for directions as
needed)
Step 3. Install the inside antenna. (See page 10-11 for directions as needed)
Step 4. Mount the signal booster, connect the outside and inside antenna cables to the signal
booster, and connect the booster to an AC power source. (See page 12-13 for directions
if needed)
Step 5. Configure gain settings on the signal booster if needed. (See page 14 for directions as
needed)
Outside Antenna
Coaxial Cable
Inside Antenna
Signal Booster
6
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
Installing Your Hardware
Step 1. Find
the area with the Strongest Signal
Before installing the outside antenna, find the area with a strong cellular signal source
from your service provider by following the directions below.
Measure the strength of the existing cellular signal in various locations.
• Apple iPhones: Dial *3001#12345#* and press Call. In the top-left corner, a dB number appears instead of bars.
•A
ndroid devices: download apps such as “Network Signal Info” in the Google Play store to measure signal
strength. Search check real signal strength to find other cell signal measurement apps.
• Internet: go to www.speedtest.net to test 3G and 4G data rates.
The signal booster requires a minimum cellular signal of low –100 dBm. Signal readings usually appear as a negative number (for example, -85). It is recommended that the
signal be between -70dB to -90dB. That’s when the signal is neither too strong nor too
weak. Signals stronger than -50dB may cause the affected bands to shut down while
displaying a flashing red LED (see the graph below). If your outside signal is too weak
(-95dB or worse) you may need a Yagi antenna instead of an omnidirectional one, which
can be aimed at the cell tower of your carrier to pull in a stronger signal to the booster.
Poor
Good
-60dB
-50dB
-70dB
-80dB
-90dB
-100dB
-110dB
Signal Strength
Excellent
Cell
Tower
Outside
Antenna
Note: Where you install your outside antenna in relation to the carrier’s cell phone tower also determines signal strength. Although cell phone
carriers try to place towers for maximum coverage, local ordinances and terrain features can restrict tower locations, which can limit signal
strength at your location.
SureCall SureCall
| 48346 Milmont
| 48346 Drive,
Milmont
Fremont
Drive, Fremont
CA 94538
CA| 1-888-365-6283
94538 | 1-888-365-6283
| sales@surecall.com
| sales@surecall.com
77
Installing Your Hardware
Step 2. Install the Outside Antenna
1. Outside omni antennas receive and send signals in a 360º radius. Yagi, or directional
antennas work best when facing the direction of cellular phone towers. Mount the outside
antenna as high as possible. If you are installing a Yagi antenna, mount it facing the
nearest cellular tower being used by your carrier in the area where you located the best
signal source (see step 1 on the previous page).
2. Ensure that the mounting area has at least a 12-inch radius clear of obstructions and
other radiating elements.
3. For best performance, place the outside antenna at least 30 feet from the inside antenna.
Note that if the mounting area is prone to weak cellular signals or if dense building
materials partially block the signal, the booster will operate at its default setting of 65 dB
gain.
4. Do not collocate antennas or operate the outside antenna with any other antenna or
signal booster.
5. Run the cable from the outside antenna to the signal booster. Hand tighten the
connection
Optional 2 - Outside Yagi
Optional 1- Outside Omni
Optional 2- Inside Panel
Signal Booster
Optional 1- Inside Right Angle
IMPORTANT:: FCC 27.5 (d)(4) Statement: Fixed, mobile, and portable (hand-held) stations operating in the 1710-1755 MHz
band as well as mobile and portable stations operating in the 1695-1710 MHz and 1755-1780 MHz bands are
limited to 1 watt EIRP. Fixed stations operating in the 1710-1755 MHz band are limited to a maximum antenna
height of 10 meters above ground. Mobile and portable stations operating in these bands must employ a means
for limiting power to the minimum necessary for successful communications.
8
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
Installing Your Hardware
Installing the Yagi Antenna:
Step 1: Install U-Bolt on pole
Step 2: Slide pipe clamp over U-Bolt with the flat side facing away from the pipe.
Step 3: Slide antenna bracket onto U-Bolt in desired location.
Step 4: Install flat washer, split washer and nut, hand tighten
Note: Antenna may be installed on a variety of pipe angles, ensure that the antenna is pointing in the direction of the closest cellular tower and is vertical with the drip hole at the bottom. To find the location of the
closest cell tower go to: www.cellreception.com.
Step 3. Install the Inside Antenna
If Coverage Area is …
And Antenna Separation is…
Set all Dials to…
1500 - 2,000
square feet
40-60 feet
Maximum Power
1,000 - 1,500
square feet
30-40 feet
55 or 60
1,000 square feet
and below
20-30 feet
45 or 50
Re
q
uir
ed
An
te
nn
aS
ep
ar
at
ion
Inside antennas come in right angle antenna and flat panel versions.
Note: As you can see from the table above, acquiring the recommended inside and outside antenna separation optimizes coverage significantly. Any reduced antenna separation reduces the booster’s coverage.
Note: If desired surface for installation plate is wood or concrete, wood or masonry screws for L-plate will have to be purchased separately.
SureCall SureCall
| 48346 Milmont
| 48346 Drive,
Milmont
Fremont
Drive, Fremont
CA 94538
CA| 1-888-365-6283
94538 | 1-888-365-6283
| sales@surecall.com
| sales@surecall.com
99
Installing Your Hardware
Installing the Panel Antenna:
Connect the antenna by firmly screwing it onto the inside port of the Fusion4Home Booster. For
best results, the antenna should be mounted in an upright position. The right angle antenna connects directly to the amplifier port labeled “Inside”.
Step 1. Choose a location for mounting the antenna on vertical surface. Ideal height off the
ground or floor should be the approximate height of your cell phone when in use.
Step 2. Using plate, mark position of desired screw placement with pencil or marker.
Step 3. Screw mounting plate into place with the slide panel protruding towards you.
Step 4. Slide antenna securely onto mounting plate.
Note: Be sure to provide enough separation from outside antenna. Panel antenna should
not face outside antenna.
Step 4. Install the Signal Booster
1. Select a location close to a working AC outlet. Do not expose the signal booster to
excessive heat, direct sunlight, moisture, and airtight enclosures.
2. If you’d like to mount the booster to a wall, mark location of screw tabs on the wall in
the desired location.
3. Use supplied screws or appropriate screws for surface of mounting location and drill
through screw tab holes on booster.
10
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
Installing your Hardware
4. Connect the outside antenna cable to the signal booster connector marked OUTSIDE.
Hand-tighten the connection.
5. Connect the inside antenna cable to the signal booster connector marked INSIDE.
Hand-tighten the connection.
6. Connect the AC power cord to the signal booster.
7. Connect the plug on the other end of the 110V AC power outlet.
8. Turn the booster’s power switch on.
Booster Hardware
The following image shows the key hardware components on the booster.
Refer to this image as you install your Fusion4Home kit components.
N connector to inside antenna
Power Switch
Connector to Inside Antenna
Power Jack
F connector to outside antenna
Note: If the Power LED does not turn ON or the Alert LEDs continue to flash, (see PAGES 15-16).This booster is rated for 5-15V input voltage.
DO NOT use the booster with a higher voltage power supply. This can damage the booster, cause personal injury, and void your warranty
SureCall SureCall
| 48346 Milmont
| 48346 Drive,
Milmont
Fremont
Drive, Fremont
CA 94538
CA| 1-888-365-6283
94538 | 1-888-365-6283
| sales@surecall.com
| sales@surecall.com
1111
Installing Your Hardware
Step 5. Configure Gain Settings
The SureCall gain dials should always be at maximum level unless the control light in a specific
band is flashing red or flashing red-yellow. In either of these
cases, the first action should be to increase the antenna
isolation between the inside and outside antenna as much
as possible and restart the booster. If the situation continues, you can lower the gain with an attenuator or, as the
last resort, reduce the booster gain by 5dB at a time until
the control light in the frequency band flashes yellow.
1. Find the PCS, Cellular, LTE-A, LTE-V and AWS dials on
top of the signal booster.
2. S
et the dials according to the coverage area and the
distance between the indoor and outdoor antennas (see
below).
If Coverage Area is …
And Antenna Separation is…
Set all Dials to…
1500 - 2,000 square feet
40-60 feet
Maximum Power
1,000 - 1,500 square feet
30-40 feet
55 or 60
1,000 square feet and below
20-30 feet
45 or 50
Note: As you can see from the table above, acquiring the recommended indoor and outdoor antenna separation optimizes coverage significantly. Any
reduced antenna separation reduces the booster’s cellular signal capabilities.
If you Want to Improve Coverage
1. Find a location that receives a stronger signal and relocate the outside antenna to that location
or, for the Yagi antenna, optimize the antenna angle.
2. Increase the distance between the outside and inside antennas.
3. Be sure your signal booster’s dB gain is turned up to maximum gain on each dial.
WARNING: Do not attenuate the uplink and downlink dB settings below 35dB. This could cause the
affected frequency band to shut down.
12
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
Troubleshooting
In the event you encounter a problem, follow the suggestions below to resolve the issue.
Troubleshooting
Problem
Resolution
Signal booster has no Verify that the switch on the power supply is turned on and red LED is ON.
power
Connect the power supply to an alternate power source.
Be sure the power source is not controlled by a switch that can remove power from the outlet.
Check the green POWER LED on the signal booster. If it is OFF, return the power supply to SureCall.
Contact tech support at
1-888-365-6283 or support@surecall.com, or go to www.surecall.com and log on to online support to
receive an RMA.
After installing your
signal booster
system, you have no
signal or reception.
Cable connections should be tightly fitted to the booster and antenna.
There should be no flashing or solid red LEDs as well as no lights flashing rapidly between two colors.
Be sure your signal booster’s dB gain is turned up to full power on each dial.
LED Indicators
LED Color
LED Condition
Resolution
Red
Solid
Band is off.
If a red light has been flashing for an extended time, the band will automatically shut off and
display a solid red light.
This can also happen when the booster attenuation has been turned all the way down.
Red
Flashing
Indicates that the booster is receiving too much signal which could cause the affected band
to automatically turn off. When this happens:
1. For kits using an OMNI outside antenna, relocate the outside antenna to a location
where the signal is weaker.
2. For kits using a YAGI outside antenna, turn the antenna in short increments away from
the signal source.
3. Increase the separation between antennas (additional vertical separation works best).
4. Add an inline attenuator to the cable coming into the outside port of the booster.
5. As a last resort, turn down the dB gain on the dial until the light goes OFF or flashes
yellow.
Yellow
Flashing
Indicates that the Automatic Gain Control (AGC) is self-adjusting. This is part of normal
operation.
Yellow
Solid
Indicates that the band is inactive. Light is off while band is active.
Yellow/Red
Alternately
Flashing
Oscillation is detected.
First, try increasing the separation between the inside and outside antennas. If your booster
kit uses two directional antennas (example: outside Yagi antenna and inside panel antenna),
ensure that they are facing away from one another.
If oscillation continues, lower the dB gain in small increments until the light turns off or flashes
yellow.
SureCall SureCall
| 48346 Milmont
| 48346 Drive,
Milmont
Fremont
Drive, Fremont
CA 94538
CA| 1-888-365-6283
94538 | 1-888-365-6283
| sales@surecall.com
| sales@surecall.com
1313
Specifications
If you Want to Improve Coverage
1. Find a location that receives a stronger signal and relocate the outside antenna to that location.
2. Optimize the Yagi antenna angle.
3. Increase the distance between the outside antenna and booster.
4. S
et each dial on the booster to maximum gain.
WARNING: Do not attenuate the uplink and downlink dB settings below 35dB. This could cause
the affected frequency band to shut down.
Fusion4Home Specifications
14
Uplink Frequency Range (MHz):
698-716 / 776 – 787 / 824-849
1850-1915 / 1710-1755 (G Block Included)
Downlink Frequency Range (MHz):
728-746 / 746 – 757 / 869-894
1930-1995 / 2110-2155 (G Block Included)
Input Impedance:
75Ω donor port / 50Ω server port
Maximum Gain:
72 dB
Noise Figure:
8 dB
Supported Standards:
CDMA, WCDMA, GSM, EDGE, HSPA+, EVDO, LTE and all cellular standards
AC Input:
Input AC110V, 60 Hz; Output DC 5-15V
Maximum Output Power:
1 Watt EIRP
Cable:
RG6 / SC-240
RF Connectors:
F-Female (Outdoor) / N-Female (Indoor)
Power Consumption:
<15W
Operation Temperature:
-4º to +158º F
Dimensions:
7.875 x 5 x 1.188 inches
Weight:
2 LB 3 oz
FCC ID / IC:
RSNFUSION4H
/ 7784A-FUSION4H
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
Kitting Information
Kitting Information
Component
Product number
Gain/Loss
Note
LTE-A
LTE-V
800 MHz
1900 MHz
1700 / 2100 MHz
SC-289W-75Ω
3 dBi
3 dBi
3 dBi
4 dBi
4 dBi / 4 dBi
SC-231W-75Ω
7 dBi
7 dBi
8 dBi
10 dBi
10 dBi / 10 dBi
Outdoor Cable*
RG6 - 50 (50’)
3.32 dB
3.32 dB
3.75 dB
6.42dB
6.22 dB / 6.68 dB
50 Feet or longer
Inside Cable*
SC-240-20NN (20’)
2.06 dB
2.06 dB
2.29 dB
3.56 dB
3.36 dB / 3.76 dB
20 Feet or longer
Inside Antenna*
SC-248W
7 dBi
7 dBi
7 dBi
10 dBi
10 dBi / 10 dBi
SC-222W
3 dBi
3 dBi
3 dBi
6 dBi
6 dBi / 6 dBi
SC-121W
1.2 dBi
1.2 dBi
1.2 dBi
3 dBi
3 dBi / 3 dBi
SC-302W
2.5 dBi
2.5 dBi
3 dBi
5 dBi
4 dBi / 5 dBi
Outdoor
Antenna*
* All equivalent antennas and cables are suitable for use with the Fusion4Home
SureCall SureCall
| 48346 Milmont
| 48346 Drive,
Milmont
Fremont
Drive, Fremont
CA 94538
CA| 1-888-365-6283
94538 | 1-888-365-6283
| sales@surecall.com
| sales@surecall.com
1515
Warranty
La puissance de sortie nominale indiquée par le fabricant pour cet appareil concerne son fonctionnement avec
porteuse unique. Pour des appareils avec porteuses multiples, on doit réduire la valeur nominale de 3,5 dB, surtout
si le signal de sortie est retransmis et qu’il peut causer du brouillage aux utilisateurs de bandes adjacentes. Une
telle réduction doit porter sur la puissance d’entrée ou sur le gain, et ne doit pas se faire au moyen d’un atténuateur
raccordé à la sortie du dispositif.
This Class A digital apparatus meets all requirements of the Canadian Interference
Causing Equipment Regulations. Operation is subject to the following two conditions; (1) this device digital apparatus
meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the
following two conditions; (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation
Cet appareillage numérique de la classe A répond a toutes les exigencies de l’interférence canadienne causant des
réglements d’équipment. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer
l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle intérference reçue, y compris l’intérference qui
peut causer l’opération peu désirée.
Three-Year Product Warranty
SureCall warrants its products for three years from the date of purchase against defects in workmanship and/or materials. Specifications are subject to change. The three-year warranty only applies to products meeting the latest FCC Certification Guidelines stated
on 2/20/2013 and going into effect April 30, 2014. A two-year warranty applies to any products manufactured before May 1, 2014.
Products returned by customers must be in their original, un-modified condition, shipped in the original or protective packaging
with proof-of-purchase documentation enclosed, and a Return Merchandise Authorization (RMA) number printed clearly on the
outside of the shipping container.
Buyers may obtain an RMA number for warranty returns by calling the SureCall Return Department toll-free at 1-888-3656283. Any returns received by SureCall without an RMA number clearly printed on the outside of the shipping container will
be returned to sender. In order to receive full credit for signal boosters, all accessories originally included in the signal booster
box must be returned with the signal booster. (The Buyer does not need to include accessories sold in addition to the signal
booster, such as antennas or cables.)
This warranty does not apply to any product determined by SureCall to have been subjected to misuse, abuse, neglect, or
mishandling that alters or damages the product’s physical or electronic properties.
SureCall warrants to the Buyer that each of its products, when shipped, will be free from defects in material and workmanship, and will perform in full accordance with applicable specifications. The limit of liability under this warranty is, at SureCall’s
option, to repair or replace any product or part thereof which was purchased up to THREE YEARS after May 1, 2014 or TWO
YEARS for products purchased before May 1, 2014, as determined by examination by SureCall, prove defective in material
and/or workmanship. Warranty returns must first be authorized in writing by SureCall. Disassembly of any SureCall product by
anyone other than an authorized representative of SureCall voids this warranty in its entirety. SureCall reserves the right to make
changes in any of its products without incurring any obligation to make the same changes on previously delivered products.
As a condition to the warranties provided for herein, the Buyer will prepay the shipping charges for all products returned to
SureCall for repair, and SureCall will pay the return shipping with the exception of products returned from outside the United
States, in which case the Buyer will pay the shipping charges.
The Buyer will pay the cost of inspecting and testing any goods returned under the warranty or otherwise, which are found to
meet the applicable specifications or which are not defective or not covered by this warranty.
Products sold by SureCall shall not be considered defective or non-conforming to the Buyer’s order if they satisfactorily fulfill the
performance requirements that were published in the product specification literature, or in accordance with samples provided
by SureCall. This warranty shall not apply to any products or parts thereof which have been subject to accident, negligence,
alteration, abuse, or misuse. SureCall makes no warranty whatsoever in respect to accessories or parts not supplied by it.
16
SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
Warranty
Limitations of Warranty, Damages and Liability:
EXCEPT AS EXPRESSLY SET FORTH HEREIN, THERE ARE NO WARRANTIES, CONDITIONS, GUARANTEES, OR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHER WARRANTIES, CONDITIONS,
GUARANTEES, OR REPRESENTATIONS, WHETHER EXPRESSED OR IMPLIED, IN LAW OR IN FACT, ORAL OR IN WRITING.
SURECALL AGGREGATE LIABILITY IN DAMAGES OR OTHERWISE SHALL NOT EXCEED THE PAYMENT, IF ANY, RECEIVED
BY CELLPHONE-MATE, INC. FOR THE UNIT OF PRODUCT OR SERVICE FURNISHED OR TO BE FURNISHED, AS THE CASE
MAY BE, WHICH IS THE SUBJECT OF CLAIM OR DISPUTE. IN NO EVENT SHALL SURECALL BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, OR SPECIAL DAMAGES, HOWSOEVER CAUSED.
All matters regarding this warranty shall be interpreted in accordance with the laws of the State of California, and any controversy that cannot
be settled directly shall be settled by arbitration in California in accordance with the rules then prevailing of the American Arbitration Association, and judgment upon the award rendered may be entered in any court having jurisdiction thereof. If one or more provisions provided
herein are held to be invalid or unenforceable under applicable law, then such provision shall be ineffective and excluded to the extent of
such invalidity or unenforceability without affecting in any way the remaining provisions hereof.
SAFETY INFORMATION
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers
consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure,
contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas
MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the
FCC or a licensed wireless service provider.
WARNING: E911 location information may not be provided or may be inaccurate for calls served BY USING THIS DEVICE.
48346 Milmont Drive
Fremont, California 94538
USA
888.365.6283
Fax: 510.996.7250
www.surecall.com
SureCall has made a good faith effort to ensure the accuracy of the information in this document and disclaims the implied warranties of
merchantability and fitness for a particular purpose and makes no express warranties, except as may be stated in its written agreement with
and for its customers. SureCall shall not be held liable to anyone for any indirect, special or consequential damages due to omissions or
errors. The information and specifications in this document are subject to change without notice. © 2014. All Rights Reserved. All
trademarks and registered trademarks are the property of their respective owners.
SureCall SureCall
| 48346 Milmont
| 48346 Drive,
Milmont
Fremont
Drive, Fremont
CA 94538
CA| 1-888-365-6283
94538 | 1-888-365-6283
| sales@surecall.com
| sales@surecall.com
1717
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your
wireless provider and have your provider’s consent. Most wireless
providers consent to the use of signal boosters. Some providers
may not consent to the use of this device on their network. If you are
unsure, contact your provider.
You MUST operate this device with approved antennas and cables
as specified by the manufacturer. Antennas MUST be installed at
least 20 cm (8 inches) from any person. You MUST cease operating
this device immediately if requested by the FCC or a licensed
wireless service provider.
WARNING. E911 location information may not be provided or may be
inaccurate for calls served by using this device.
This device may be operated ONLY in a fixed location for in-building
use.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC 27.50(d)(4) Statement: Fixed, mobile and portable (hand-held) stations operating in the 1720-1755 MHz band are limited
1 Watt EIRP. Fixed stations operating in this band are limited to a maximum antenna height of 10 meters above ground. Mobile
and portable stations operating in this band must employ a means for limiting power to the minimum necessary for successful
communications.
18
Dirve, Fremont CA 94538 | 1-888-365-6283 | sales@surecall.com
SureCall | 48346 Milmont Drive,
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising