assembly and instruction guide

assembly and instruction guide
Page 1
ASSEMBLY AND INSTRUCTION GUIDE
Model #: 40341, 40342
ABOUT YOUR OUTDOOR NIGHT-LIGHT™
BATTERY INSTALLATION
•
1. To access the battery compartment, slide the tab on the bottom of
the mounting plate to “Open” and slide down the mounting plate
on the back side of your Outdoor Night-Light™.
2. Then push up the tab of the battery cover inside and replace the
batteries according to the orientation noted in Diagram 2.
•
•
•
•
•
Light where you need it most! Your Outdoor Night-Light™ will
guide you every step of the way.
Perfect for both indoor and outdoor use. Place your Outdoor
Night-Light™ outdoors by the entrance door, and you won’t
fumble for your keys or the lock anymore. Place it indoors and
you no longer have to enter your house in the dark.
Use it outdoors for steps, doors, walkways, porches, gates,
sheds, decks and more.
Use it indoors for hallways, bathrooms, steps, and any other dark
spaces you can imagine,
The three brilliant LEDs will light your way, preventing you from
falling down the stairs or tripping over objects. Great for lighting
up dark areas.
Totally portable and needs no wiring. Uses 3 AA batteries (not
included), which will last 6-12 months depending on usage.
CHOOSING A LOCATION
The selected location should not be near light sources, such as street
or porch lighting, as these may cause the Outdoor Night-Light™ to
turn off automatically. The Outdoor Night-Light™ should also be
installed away from heaters, air conditioners, barbecues, vents, and
large reflective surfaces such as swimming pools and jacuzzis, and
white walls. To avoid damage to some components, do not aim the
motion sensor towards the sun.
At night, the LED lights will remain on for about 50-60 seconds after
the last detected movement. If a movement is detected while the
lights are on, the light duration will be reset and remain on for about
another 50-60 seconds.
Diagram 1
Diagram 2
Your Outdoor Night-Light™ uses three AA batteries. The batteries
typically last 6 months to 1 year under normal use.
Note: If your Outdoor Night-Light™ does not turn on after
battery installation: Make sure fresh batteries have been
inserted matching the correct +/- polarity orientation and are
making secure contact with the terminals.
MOUNTING YOUR OUTDOOR NIGHT-LIGHT™
1. Take out the mounting plate by sliding it down as shown in Battery
Installation.
2. Put the flat side against the wall and
use the two screws supplied to install
the mounting plate. If you are installing
it on a very hard surface, you may need
to first drill holes for the screws. The
included screw anchors can be used for
drywall, cement, brick, or similar
surfaces.
3. Slide down the main body of your
Outdoor Night-Light™ onto the mounting plate after the plate is
attached to the wall.
OPERATING YOUR OUTDOOR NIGHT-LIGHT™
1. Install the batteries (see BATTERY INSTALLATION section).
2. Choose a location (see CHOOSING A LOCATION section).
3. Mount the light (see MOUNTING YOUR OUTDOOR NIGH LIGHT
section), or simply stand the unit on any flat surface.
4. Built-in motion sensor automatically turns on the light when movement is detected in the area. The light remains on as long as motion
continues to be detected. Please note that there is no On/Off
switch, the light can only be activated by motion.
5. Built-in photosensor allows the light to only be turned on at night or in
darkness, conserving energy.
Page 2
PROBLEM
Light does not turn on when
there is movement in the
detection area.
Light turns on for no apparent
reason (false trigger).
POSSIBLE CAUSE
POSSIBLE SOLUTION
1. Batteries are old.
1. Replace the batteries with fresh batteries.
2. Nearby lighting is too bright.
2. Redirect the sensor or install in a different location,
away from other lighting.
3. The sensor is facing the wrong direction.
1. Heat sources such as air conditioners, vents,
barbecues, other outside lighting, or moving cars
are triggering the motion sensor.
2. Pets or other animals are triggering the motion
sensor.
3. Reflections from swimming pools, jacuzzis, white
walls, or other large reflective surfaces are triggering the motion sensor.
3. Aim the sensor toward the desired detection area.
1. Install the Outdoor Night-Light™ away from the
sources of interference.
2. Redirect the sensor.
3. Install the Outdoor Night-Light™ away from the
sources of reflections.
SPECIFICATIONS
Batteries Required: 3 AA cell alkaline
Wattage: Maximum 0.72 W, static ≤ 0.24 mW
Voltage: 4.5 V DC
Light Duration: approx. 55 seconds from last motion detected
Weatherproof Rating: IP44
90 DAY LIMITED WARRANTY
This Motion-Activated Light is warranted against faulty material and/or workmanship for a period of 90 days from date of original
purchase. The obligation of the manufacturer, under this warranty, is limited to servicing and replacing defective parts when the unit is
returned to MAXSA Innovations, freight pre-paid during the warranty period. To obtain warranty repair, the purchase receipt should be
returned with the product.
This warranty becomes void on any unit which has been tampered with, damaged by accident, or damaged otherwise by improper
operation.
This guarantee is in addition to any guarantees implied by State or Federal Legislation.
info@maxsainnovations.com
v10.5
2010
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising