CAT CARD SERIES - Select Engineered Systems

CAT CARD SERIES - Select Engineered Systems
(CAT CARD 2 and CAT CARD 4 )
The CAT Card 2 and CAT Card 4 Systems are full featured
access control systems. These systems are available in 2 door
(CAT Card 2) and 4 door (CAT Card 4) configurations and can be
linked by using the MUI (Multi Unit Interface) Option.
The systems can be expanded to control up to 16 doors and 255
relays point for control of elevators, HVAC, lights or other facility
control points that require activation or monitoring (using optional
CAT Card Reader expansion and Relay Expansion modules). The
CAT Card systems can be interfaced with the CAT Series. The
LCD and keypad mounted inside the unit housing allows easy
programming or the units can be programmed via SELCOM if a
phone line is connected or an optional Serial card plugged on to
the unit.
 CAT CARD 2 provides 2 wiegand inputs.
 CAT CARD 4 provides 4 wiegand inputs.
 Display and keypad internal for doing service or
 Two entrance control with 2 relays.
 RS485 expansion port for optional CATDR4
expansion module (up to 16 entrances) and/or
CATRLY8 relay expansion module (elevator
 Database has 6 cards per control number for
programming by department or group.
 56k baud modem.
 13,000 event log buffer, Clock calendar.
 Non-volatile memory.
 Card/Code expansion remotely.
(readers not included)
♦ CATCOMRF wireless data connection for expansion.
 NIC2, network interface card provides a TCP/IP
interface for network programming.
 OPTK4DR is a plug-on module for expanding the CAT
series from 2 readers to 4 readers internally.
 CATDR4 is a remote 4 door module that attaches to a
CAT system to expand it’s capability up to 16
entrances depending on CAT configuration.
 CATRLY8 is an elevator / aux. relay module that
contains 8 relays and can be programmed for elevator
control, light or HVAC control. Up to 32 CATRLY8’s can
be connected to a CAT system.
 RS232 or current loop serial communications: Serial I/O
 Programmable via modem.
 RS485 expansion conversion kit (CATRS485CONVKIT)
 Built-in charging circuit for backup battery.
 MUI (Multi Unit Interface) Allows up to 8 CAT’s to share a
 REX (request to exit), alarm shunt and door
sense input.
single telephone line (OPTKMUI).
 Card Readers and RF Receivers / Transmitters with or
without HID Proximity
 16 time zones, 16 access levels and 16 access
groups with max card capacity of 16,200.
 LRP - Long Range Proximity Readers and Cards.
 2 year limited warranty.
 Select Pass / Multi-Pass RF Transmitters.
 Multi-level surge suppression for protection
against power surges.
 Selcom Secured Programming Software
 Supports any standard wiegand device.
 OPTRSTWRH, weather resistant enclosure for CAT
CARD 2 and CAT CARD 4.
(CAT CARD 2 and CAT CARD 4 )
 Dimensions: 11'” W x 11” H x 3 1/2” D
 Up to 16,200 cards each with a reference
 Material Used: Housing 12 ga. Painted steel.
 Up to 16 entrances, maximum.
 Power Input: 16.5 VAC, 20 or 40 VA UL listed
transformer (provided with unit).
 Controls as many as 255 relays for elevator
and auxiliary control when adding the
CATRLY8 (relay expansion modules).
 Emergency Battery: 12V .7 AHR GEL CELL on
constant charge (for control of line voltage variation
and short term telephone support only, optional).
 Telephone Line: Standard voice grade RJ11C
 Mounting: Surface.
 Memory Type: Non-volatile.
 Shipping Weight: Approx. 7 lbs.
 Operating Environment: Temp.: -20ºC to +60ºC
(CATV temp.: 0 to 40ºC) Relative humidity: 5% to
95% non-condensing.
 Relay Output: Form C dry contact 24V @ 3AMP.
 FCC Reg.: #CPW74F63331MTE.
 ARL LISTED (UL Equivalent)
 16 time zones, 16 access levels and 16
access groups.
 (8) CAT CARDs can be connected to one
phone line using MUI’s (one each) and all can
be programmed remotely.
 13,000 Event Log Buffer (before wrapping)
 56K baud modem.
 Programming for the latest versions of Windows
including Vista, 7 and 8 using optional SELCOM
SECURED software.
 Code / Phone / Card capacities can be
upgraded remotely by the factory, through
authorized dealers only.
♦Residential gated communities or commercial use.
♦Apartment buildings, Condominiums, Townhouses.
♦Retirement homes / Convalescent homes.
♦Hospitals, Office buildings, and Banks.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF